Estudo das propriedades mecânicas de biocompósitos de polipropileno reforçados com fibras naturais

This research presents an approach to the addition of curauá fibers and licuri fibers in a polypropylene resin matrix, such as an alternative proposal to reinforce the polymeric composites. Fiber content of 0 %, 5 %, 10 %, and 20% were analyzed for verification of their mechanical properties comparing them, inclusive with the properties of polypropylene. The grainulated biocomposites had been prepared in an extrusora. The test bodies had been molded by injection and submitted to the mechanical essays uniaxial traction, flexion on three points, impact, in addition to thermal tests (HDT). These biocomposites had been also subjected the essay physicist-chemistry index of fluidity (IF). It was observed that the biocomposites of PP with 20% curauá, obtained bigger increase in the modulus of elasticity and a bigger reduction in the resistance to the impact. In the mechanical behavior, for all the biocomposites, these were increases in values of the limit of drainage and tension of rupture, when tested by uniaxial traction, as they added the fibers. Another important point was the increase of the resistance the flexion. It was also noted that the addition of fibers reduced the thermal degradation of the mixture natural fibers / polypropylene.

Análise de desempenho de um refrigerador de pequeno porte com drop in de refrigerantes hidrocarbonetos

From what was stated in the Montreal Protocol, the researchers and refrigeration industry seek substitutes for synthetic refrigerants -chlorofluorocarbons (CFCs) and HCFCs (HCFC) - that contribute to the depletion of the ozone layer. The phase-out of these substances was started using as one of the replacement alternatives the synthetic fluids based on hydro fluorocarbons (HFCs) that have zero potential depletion of the ozone layer. However, contribute to the process of global warming. HFC refrigerants are greenhouse gases and are part of the group of gases whose emissions must be reduced as the Kyoto Protocol says. The hydrocarbons (HC's), for not contribute to the depletion of the ozone layer, because they have very low global warming potential, and are found abundantly in nature, has been presented as an alternative, and therefore, are being used in new home refrigeration equipment in several countries. In Brazil, due to incipient production of domestic refrigerators using HC's, the transition refrigerants remain on the scene for some years. This dissertation deals with an experimental evaluation of the conduct of a drinking fountain designed to work with HFC (R-134a), operating with a mixture of HC's or isobutane (R-600a) without any modification to the system or the lubricating oil. In the refrigeration laboratory of Federal University of Rio Grande do Norte were installed, in a drinking fountain, temperature and pressure sensors at strategic points in the refrigeration cycle, connected to an acquisition system of computerized data, to enable the mapping and thermodynamics analysis of the device operating with R-134a or with a mixture of HC's or with R-600a. The refrigerator-test operating with the natural fluids (mixture of HC's or R-600a) had a coefficient of performance (COP) lower than the R-134a

Obtenção de compósitos cerâmicos reforçados com carbetos refratários a partir de precursores poliméricos

In this work, were produced ceramic matrix composites based in SiCxOy e Al2O3 reinforced with NbC, by hydrosilylation reaction between D4Vi and poly(methylhydrosiloxane) mixtured with Al2O3 as inert filler, Nb and Al as reactive filler. After the mixture and compactation at 80ºC (warm pressing), the samples were pyrolised at 1200 and 1400ºC and infiltred with ICZ and LZSA respectively, and thermically, physical and structurally characterized by X-ray diffraction, density and porosity, flexural mechanical strength and fracture surface by scanning electron microscopy. The yield ceramic obtained after pyrolysis for studied composition at 1200ºC was 95%. The obtained phases had been identified as being Al3Nb, NbSi2 and NbC. The composite material presented apparent porosity varying of 15 up to 32% and mechanical flexural strenght of 32 up to 37,5MPa. After the fracture surface analysis, were observed a phases homogeneous dispersion, with some domains of amorphous and crystalline aspect. The samples that were submitted the infiltration cycle presented a layer next the surface with reduced pores number in relation to the total volume

Obtenção de pós de Nb a partir da redução aluminotérmica com ignição por plasma

The aluminothermic reduction consists in an exothermic reaction between a metallic oxide and aluminum to produce the metal and the scum. The extracted melted metal of that reaction usually comes mixed with particles of Al2O3 resulting of the reduction, needing of subsequent refine to eliminate the residual impure as well as to eliminate porosities. Seeking to obtain a product in powder form with nanometric size or even submicrometric, the conventional heat source of the reaction aluminothermic , where a resistor is used (ignitor) as ignition source was substituted, for the plasma, that acts more efficient way in each particle of the sample. In that work it was used as metallic oxide the niobium pentoxide (Nb2O5) for the exothermal reaction Nb2O5 + Al. Amounts stoichiometric, substoichiometric and superestoichiometric of aluminum were used. The Nb2O5 powder was mixed with aluminum powder and milled in planetarium of high energy for a period of 6 hours. Those powders were immerged in plasm that acts in a punctual way in each particle, transfering heat, so that the reaction can be initiate and spread integrally for the whole volume of the particle. The mixture of Nb2O5 + Al was characterized through the particle size analysis by laser and X-ray diffraction (DRX) and the obtained product of reaction was characterized using the electronic microscopy of sweeping (MEV) and the formed phases were analyzed by DRX. Niobium powders with inferior sizes to 1 mm were obtained by that method. It is noticed, through the analysis of the obtained results, that is possible to accomplish the aluminothermic reduction process by plasma ignition with final particles with inferior sizes to the original oxide

Estudo da fibra de coco como reforço em tijolo de solocimento

To take care of to the demand of the new constructions in the low income communities and to develop the production of a strengthened alternative brick with staple fibers of coconut, capable to contribute mainly with the recycling of the green and mature coconut in the urban and agricultural lexes, this research was developed, to confection bricks of soil-cement with coconut fiber. Ecologically correct material and of low cost, since the greenhouse use of or oven for burning will be manufactured without. The study it presents a set of tables and graphs that prove good indices found in the values of the density, water absorption, axial compressive strength and isolation term acoustics, with evidential results that make possible the production in industrial character with press mechanics or the place of the workmanship with manual form. The preparation of coconut staple fibers was made of natural form without use of chemical products not to deprive of characteristics the properties mechanical physicist-chemistries and of the same ones. The sixty bricks produced in simple and manual press had been carried through in four lots of fifteen units. The mixture of aggregates was made in four different traces composites for: ground erinaceous, cement, fiber of dry coconut and water; the bricks had been compact in the press and cured in natural way under an area covered during the minimum time of seven days

Diagnóstico de descarga de cátodo oco de ar e pós-descarga Ar N2 por espectroscopia de emissão óptica e espectrometria de massa

Many applications require that the plasma discharge is produced apart from the surface to be processed, thus preventing damage caused by bombardment and/or plasma radiation. In the post-discharge regime in various applications thermally sensitive materials can be used. In this work, active species produced by discharge and post-discharge hollow cathode were diagnosed by optical emission spectroscopy and mass spectrometry. The discharge was produced with the gases Ar and Ar - N2 gas flow ranging from 1 to 6 cm3/min and electric current between 150 to 600 mA. It was estimated that the ion density inside the hollow cathode, with 2 mm diameter ranged between 7.71 and 14.1 x 1015 cm-3. It was observed that the gas flow and the electric current changes the emission intensity of Ar and N2 species. The major ionic species detected by quadrupole mass spectrometry were Ar+ and N2+. The ratio of optical emission intensities of N2(1 +)/Ar(811 nm) was related to the partial pressure of N2 after the hollow cathode discharge at low pressure

Estudo do aproveitamento do rejeito da mineração de esmeraldas na produção de refratários conformados isolantes

Emerald mining is an important area of the economy in Brazil, country which is in second place among the exporting nations of this gem. Due to the process of extraction, a great amount of reject is generated. Since there is no appropriate destination, the reject is abandoned around the mining industries, contributing to environment degradation. Nowadays, some of the most relevant things to an industry in general are: energy conservation, cost reduction, quality and productivity enhancement. The production of isolating, transformed refractory materials achieves the sustainability dimension when protection of the environment is incorporated to such process. This work investigates the use of emerald mining rejects in the ceramic body of refractory materials, aiming at obtaining a product whose characteristics are compatible with commercial products and, at the same time, allow the use of such rejects to solve the environmental issue caused by its disposal in nature. X-ray fluorescence analysis show that the emerald reject obtained after the flotation to extract molybdenum and mica has 70% of silica and alumina (SiO2+Al2O3) and 21% of a basic oxides and alkaline metals and earthy alkaline mixture (Na2O, K2O, CaO e MgO). Because of the significant amount of silica and alumina present in the reject, four refractory ceramic bodies were prepared. Samples with a rectangular shape and dimensions 100x50x10 mm were pressed in a steel mold at 27,5 MPa and sintered at 1200ºC for 40 min. under environment atmosphere in a resistive oven. The sintered samples were characterized in relation to the chemical composition (FRX), mineralogical composition (DRX), microstructure (MEV) and physical and mechanical properties. The results indicate that the mixture with 45% of reject, 45% of alumina and 10% of kaolin presents a refractory quality of 1420ºC, dimensional linear variation below 2.00%, apparent specific mass of 1,56 g/cm3 and porosity of 46,68%, which demonstrates the potential use of the reject as raw material for the industry of isolating transformed refractory materials

Estudo das propriedades físico-químicas do biodiesel e suas influências na deterioração dos elastômeros aplicados no sistema de injeção dos motores diesel

The biodiesel use has become important due to its renewable character and to reduce environmental impacts during the fuel burning. Theses benefit will be valid if the fuel shows good performance, chemistry stability and compatibility with engines. Biodiesel is a good fuel to diesel engines due to its lubricity. Then, the aimed of this study was to verify the physicalchemistry properties of biodiesel and their correlations with possible elastomers damage after biodiesel be used as fuel in an injection system. The methodology was divided in three steps: biodiesels synthesis by transesterification of three vegetable oil (soybean, palm and sunflower) and their physical-chemistry characterization (viscosity, oxidative stability, flash point, acidity, humidity and density); pressurized test of compatibility between elastomers (NBR and VITON) and biodiesel, and the last one, analyze of biodiesels lubricity by tribological test ball-plan( HFRR). Also, the effect of mixture of biodiesel and diesel in different concentrations was evaluated. The results showed that VITON showed better compatibility with all biodiesel blends in relation to NBR, however when VITON had contact with sunflower biodiesel and its blends the swelling degree suffer higher influences due to biodiesel humidity. For others biodiesels and theirs blends, this elastomer kept its mechanical properties constant. The better tribological performance was observed for blends with high biodiesel concentration, lower friction coefficient was obtained when palm biodiesel was used. The main mechanisms observed during the HFRR tests were abrasive and oxidative wear

Estudo do potencial refratário de argilas sílico-aluminosas do Rio Grande do Norte

The segment of the structural ceramics industry is one of the most important to the economy of Rio Grande do Norte. The supply chain makes a total of 206 companies that are distributed in 39 counties, concentrated in three regional centers: Seridó Apodi / Assu and great Natal. The ceramic industry in the state is around 80 million pieces per month, with 50,186 million of these tiles, which makes the Rio Grande do Norte one of the largest manufacturers of product in the Country. Different ceramic products can be manufactured by mixing two or more clays and accessory minerals. Mixtures acquire characteristics and form what is called the ceramic body. Refractory masses have a high melting point and thermal shock support. Its composition contains refractory clays with a little iron oxide and material fluxes. A line of semi-refractory ceramic products that stands out for its high added value are the bricks in ivory or red, used in building barbecues, fireplaces, wood stoves and braziers. The aim of this study was to use alumina-clay or silica- alumina-clay to the industrial RN, for the production of refractory bricks semi-refractory burning light. Clay and Kaolin were characterized for their chemical and mineralogical composition, immediately after ceramic bodies were made with different concentrations of the components, they were raised, pressed and sintered. After sintering the resulting products were characterized in terms of mechanical, thermal and dimensional than the characterization by X-ray diffraction and scanning electron microscopy. After obtaining the results, we concluded that the studied clay can be used for the production of semi-refractory bricks

Seletividade de herbicidas em variedades de cana-de-açúcar

Este trabalho teve como objetivo avaliar a seletividade do herbicida topramezone aplicado de forma isolada e em mistura com tebuthiuron, em pós-emergência inicial, sobre dez variedades de cana-de-açúcar em condição de cana-planta. Os tratamentos utilizados foram: topramezone + Dash® (70 g ha-1 + 0,25% v/v); topramezone + tebuthiuron + Dash® (70 + 1.000 g ha-1 + 0,25% v/v); topramezone + tebuthiuron + Dash® (100 + 1.000 g ha-1 + 0,25% v/v); e ametryn + tebuthiuron (1.500 + 1.000 g ha-1), aplicados aos 35 dias após o plantio, além de uma testemunha sem aplicação de herbicidas. Durante a condução do experimento, todas as parcelas permaneceram livres da interferência das plantas daninhas por meio de capinas. As plantas de cana-de-açúcar estavam com duas a quatro folhas por ocasião da aplicação dos herbicidas. O delineamento experimental utilizado foi o de blocos casualizados em parcelas subdivididas, com quatro repetições, sendo as variedades dispostas nas parcelas e os herbicidas nas subparcelas. As variedades utilizadas foram: SP 83 2847, SP 80 3280, RB 85 5453, SP 80 1842, SP 89 1115, RB 86 7515, PO 8862, RB 85 5156, SP 80 1816 e SP 81 3250. As avaliações visuais de fitotoxicidade foram realizadas aos 7, 14, 28 e 35 dias após a aplicação. Ao final do estudo foram determinados os parâmetros tecnológicos pol, fibra e brix e os parâmetros produtivos rendimento de colmos e produção de açúcar. A formulação isolada de topramezone seguida de suas misturas com tebuthiuron proporcionaram inicialmente severos sintomas visuais de injúrias às plantas de cana-de-açúcar; contudo, as plantas de todas as variedades testadas tiveram uma total recuperação visual a partir dos 35 dias após a aplicação dos herbicidas. A mistura de tebuthiuron com topramezone reduziu os sintomas de injúrias iniciais provocados por este último. A mistura de ametryn + tebuthiuron foi o tratamento que evidenciou a ação fitotóxica menos severa às plantas, independentemente da variedade estudada. Nenhum dos herbicidas testados afetou negativamente os componentes tecnológicos e produtivos, sendo as diferenças observadas dependentes apenas das variedades. Podem-se considerar seletivos os herbicidas utilizados sobre as variedades avaliadas de cana-de-açúcar.

Aperfeiçoamento no projeto de um protótipo de misturador-decantador à inversão de fases visando aplicação na indústria do petróleo

In the oil industry the mixture oil/water occurs in the operations of production, transportation and refining, as well as during the use of its derivatives. The amount of water produced associated with the oil varies and can reach values of 90% in volume in the case of mature phase of the production fields. The present work deals with the development of new design of the Mixer Settler based on Phase Inversion (MDIF) in a laboratory scale. We envisage this application in industrial scale so the phases of project, construction and operation are considered. The modifications most significant, in comparison with the original prototype, include the materials of construction and the substitution of the equipment used in the mixing stage of the process. It was tested the viability of substitution of the original system of mechanical mixing by a static mixer. A statistical treatment by means of an experimental design of composed central type was used in order to evaluate the behavior of the main variables of the separation process as function of the efficiency of separation for the new device. This procedure is useful to delimit an optimal region of operation with the equipment. The variables of process considered on the experimental design were: oil concentration in the feeding water (mg/L); Total volumetric flow rate (L/h); Ratio organic/water on volumetric basis (O/A). The separation efficiency is calculated by comparison of the content of oil and greases in the inlet and outlet of the equipment. For determination of TOG (Total Oil and Grease), the method used was based in the absorption of radiation in the infra-red region. The equipment used for these determinations was InfraCal® TOG/TPH Model HATR-T2 of the Wilks Enterprise, Incorporation. It´s important to stand out that this method of measure has being used by PETROBRAS S.A. Results of global efficiency of separation oil/water varied from 75.3 to 97.7% for contaminated waters containing up to 1664,1 mg/L of oil. By means of tests carried out with a real sample of contaminated water supplied by PETROBRAS we have got an effluent specified in terms of the legal standards required for discharging. Thus, the new design of equipment constitutes a real alternative for the conventional systems of treatment of produced water in the oil industry

Seletividade do herbicida saflufenacil a Eucalyptus urograndis

As áreas com plantios florestais estão constantemente em expansão, e a interferência das plantas daninhas alteram o crescimento e desenvolvimento de plantas de eucalipto, pois estas competem por água, nutrientes, espaço e luz. Objetivou-se com este estudo avaliar a seletividade do herbicida saflufenacil, aplicado com e sem óleo mineral Dash, em plantas de Eucalyptus urograndis, em diferentes locais de aplicação (planta, solo e solo + planta). O delineamento experimental adotado foi o inteiramente casualizado, com quatro repetições, constituído de um fatorial 3 x 11, sendo três locais de aplicação do herbicida na planta e 11doses do herbicida saflufenacil combinadas ou não com o adjuvante Dash. Cada parcela constou de um vaso com uma planta. Os tratamentos usados foram: 0, 25, 25+Dash (0,5% v/v), 50, 50+Dash (0,5% v/v), 75, 100, 125, 150, 175 e 200 g i.a. ha-1 . Foram realizadas avaliações visuais de fitointoxicação durante 56 dias após aplicação (DAA). Avaliouse, ainda, a altura, o diâmetro de caule e a biomassa seca das plantas. Todas as doses testadas de saflufenacil sem adjuvante mostraram-se seletivas às plantas de E. urograndis, independentemente do local de aplicação. A adição de Dash aos tratamentos proporcionou injúrias severas às plantas nas avaliações iniciais, quando aplicado sobre as plantas, com a recuperação total destas no fim do ensaio, aos 56 DAA. A aplicação do herbicida em mistura com adjuvante somente no solo não causou intoxicação às plantas de eucalipto.

Isolation and mycelial growth of Diehliomyces microsporus: effect of culture medium and incubation temperature

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fontes e períodos de contato de fertilizantes e germinação de sementes de Brachiaria brizantha

A mistura de sementes forrageiras com fertilizantes pode viabilizar o cultivo consorciado, por diminuir a competição com a cultura produtora de grãos. No entanto, se realizada muito antes da semeadura, pode prejudicar a emergência e o estabelecimento das forrageiras. Realizou-se trabalho em condições de laboratório e casa de vegetação, em Botucatu (SP), com o objetivo de avaliar a germinação de sementes de Brachiaria brizantha em razão do tempo de mistura com fertilizantes químicos. O delineamento experimental empregado foi o inteiramente casualizado, com quatro repetições. Os tratamentos constaram de um fatorial 6 x 8, constituído de diferentes períodos de contato das sementes de Brachiaria brizantha cultivar Marandu (0, 6, 12, 24, 48 e 96 h) com os fertilizantes uréia, sulfato de amônio, cloreto de potássio, sulfato de potássio, superfosfato simples, superfosfato triplo e formulado N-P-K (8-28-16) nas formas de mistura de grânulos e farelado. Não houve relação entre os testes de germinação em laboratório e a emergência a campo. No solo, a emergência das plântulas de Brachiaria brizantha não é afetada se realizada a mistura com fertilizantes minerais fosfatados, cloreto de potássio e formulado farelado até 96 h antes da semeadura.

Controle biológico da podridão radicular e promoção de crescimento em pepino hidropônico com microrganismos de manguezais

O objetivo deste trabalho foi avaliar a capacidade de microrganismos de manguezais para controlar a podridão radicular causada por Pythium aphanidermatum e para promover o crescimento em pepino hidropônico (Cucumis sativus). Avaliaram-se 19 microrganismos quanto ao controle da doença em mini-hidroponia. Os microrganismos mais promissores para esse fim - Gordonia rubripertincta SO-3B-2 e a mistura dos isolados G. rubripertincta SO-3B-2, MB-P3A-49, MB-P3-C68 e SO-3L-3, de Pseudomonas stutzeri, e Bacillus cereus AVIC-3-6 - foram, posteriormente, testados quanto à promoção de crescimento do pepineiro, em casa de vegetação. Microrganismos de manguezais podem ter importância funcional no controle biológico da podridão radicular causada por P. aphanidermatum e na promoção do crescimento do pepineiro cultivado em hidroponia. Os microrganismos G. rubripertincta SO-3B-2 e P. stutzeri MB-P3A-49 são promissores na promoção do crescimento das plantas não infestadas com o patógeno.