Effect of enzymatic treatment on the cross-flow microfiltration of acai pulp: Analysis of the fouling and recovery of phytochemicals

This study aimed to investigate the effects of pectinase enzyme treatment of acai pulp on cross-flow microfiltration (CFMF) performance and on phytochemical and functional characteristics of their compounds. Analyses of fouling mechanisms were carried out through resistance in series and blocking in law models. The enzymatic treatment was conducted using Ultrazym(R) AFPL (Novozymes A/S) at 500 mg kg(-1) of acai pulp for 30 min at 35 degrees C. Before microfiltrations, untreated and enzyme-treated acai pulps were previously diluted in distilled water (1:3; w/v). CFMFs were conducted using commercial alpha-alumina (alpha-Al2O3) ceramic membranes (Andritz AG, Austria) of 0.2 mu m and 0.8 mu m pore sizes, and 0.0047 m(2) of filtration area. The microfiltration unit was operated in batch mode for 120 min at 25 degrees C and the fluid-dynamic conditions were transmembrane pressure of Delta P = 100 kPa and cross-flow velocity of 3 m s(-1) in turbulent flow. The highest values of permeate flux and accumulated permeate volume were obtained using enzyme-treated pulp and 0.2 mu m pore size membranes with steady flux values exceeding 100 L h(-1) m(-2). For the 0.8 mu m pore size membrane, the estimated total resistance after the microfiltration of enzyme-treated acai pulp was 21% lower than the untreated pulp, and for the 0.2 mu m pore size membrane, it was 18%. Cake filtration was the dominant mechanism in the early stages of most of the CFMF processes. After approximately 20 min, however, intermediate pore blocking and complete pore blocking contributed to the overall fouling mechanisms. The reduction of the antioxidant capacity of the permeates obtained after microfiltration of the enzyme-treated pulp was higher (p < 0.01) than that obtained using untreated pulp. For total polyphenols, on the contrary, the permeates obtained after microfiltration of the enzyme-treated pulp showed a lower mean reduction (p < 0.01) than those from the untreated pulp. The results show that the enzymatic treatment had a positive effect on the CFMF process of acai pulp. (C) 2012 Elsevier Ltd. All rights reserved.

In Vitro Evaluation of the Probiotic Potential of Bacteriocin Producer Lactobacillus sakei 1

Lactobacillus sakei 1 is a food isolate that produces a heat-stable antimicrobial peptide (sakacin 1, a class ha bacteriocin) inhibitory to the opportunistic pathogen Listeria monocytogenes. Bacterial isolates with antimicrobial activity may be useful for food biopreservation and also for developing probiotics. To evaluate the probiotic potential of L. sakei I, it was tested for (i) in vitro gastric resistance (with synthetic gastric juice adjusted to pH 2.0, 2.5, or 3.0); (ii) survival and bacteriocin production in the presence of bile salts and commercial prebiotics (inulin and oligofructose); (iii) adhesion to Caco-2 cells; and (iv) effect on the adhesion of L. monocytogenes to Caco-2 cells and invasion of these cells by the organism. The results showed that L. sakei I survival in gastric environment varied according to pH, with the maximum survival achieved at pH 3.0, despite a 4-log reduction of the population after 3 h. Regarding the bile salt tolerance and influence of prebiotics, it was observed that L. sakei 1 survival rates were similar (P > 0.05) for all de Man Rogosa Shame (MRS) broth formulations when tests were done after 4 h of incubation. However, after incubation for 24 h, the survival of L. sakei 1 in MRS broth was reduced by 1.8 log (P < 0.001), when glucose was replaced by either inulin or oligofructose (without Oxgall). L. sakei 1 was unable to deconjugate bile salts, and there was a significant decrease (1.4 log) of the L. sakei 1 population in regular MRS broth plus Oxgall (P < 0.05). In spite of this, tolerance levels of L. sakei 1 to bile salts were similar in regular MRS broth and in MRS broth with oligofructose. Lower bacteriocin production was observed in MRS broth when inulin (3,200 AU/ml) or oligofructose (2,400 AU/ml) was used instead of glucose (6,400 AU/ml). L. sakei I adhered to Caco-2 cells, and its cell-free pH-neutralized supernatant containing sakacin I led to a significant reduction of in vitro listerial invasion of human intestinal Caco-2 cells.

Occurrence of molds on laminated paperboard for aseptic packaging, selection of the most hydrogen peroxide- and heat-resistant isolates and determination of their thermal death kinetics in sterile distilled water

This study aimed at enumerating molds (heat-labile and heat-resistant) on the surface of paperboard material to be filled with tomato pulps through an aseptic system and at determining the most heat-and hydrogen peroxide-resistant strains. A total of 118 samples of laminated paperboard before filling were collected, being 68 before and 50 after the hydrogen peroxide bath. Seven molds, including heat-resistant strains (Penicillium variotii and Talaromyces flavus) with counts ranging between 0.71 and 1.02 CFU/cm(2) were isolated. P. variotii was more resistant to hydrogen peroxide than T. flavus and was inactivated after heating at 85 degrees C/15 min. When exposed to 35 % hydrogen peroxide at 25 degrees C, T. flavus (F5E2) and N. fischeri (control) were less resistant than P. variotti (F1A1). P. citrinum (F7E2) was shown to be as resistant as P. variotti. The D values (the time to cause one logarithmic cycle reduction in a microbial population at a determined temperature) for spores of P. variotii (F1A1) and N. fischeri (control) with 4 months of age at 85 and 90 degrees C were 3.9 and 4.5 min, respectively. Although the contamination of packages was low, the presence of heat-and chemical-resistant molds may be of concern for package sterility and product stability during shelf-life. To our knowledge, this is the first report that focuses on the isolation of molds, including heat-resistant ones, contaminating paperboard packaging material and on estimating their resistance to the chemical and physical processes used for packaging sterilization.

Ethyl carbamate kinetics in double distillation of sugar cane spirit

The aim of this study was to verify the effect of a double distillation on the reduction of the ethyl carbamate content in sugar cane spirit. Ethyl carbamate is a potentially carcinogenic compound normally present at critical levels in sugar cane spirit, constituting a public health problem and therefore hindering the export of this beverage. The ethanol, copper and ethyl carbamate contents were evaluated, using gas chromatography/mass spectroscopy, during a double distillation of the fermented sugar cane juice. The distillate fraction from the first distillation accumulated 30% of the ethyl carbamate formed. In the second distillation, the ethyl carbamate and the copper content increased during the process as the alcohol content decreased, and only 3% of the ethyl carbamate formed was collected in the spirit. Double distillation decreased the ethyl carbamate content in the sugar cane spirit by 97%. (C) Copyright 2012 The Institute of Brewing & Distilling

Direct Determination of Sugar Cane Quality Parameters by X-ray Spectrometry and Multivariate Analysis

Current methods for quality control of sugar cane are performed in extracted juice using several methodologies, often requiring appreciable time and chemicals (eventually toxic), making the methods not green and expensive. The present study proposes the use of X-ray spectrometry together with chemometric methods as an innovative and alternative technique for determining sugar cane quality parameters, specifically sucrose concentration, POL, and fiber content. Measurements in stem, leaf, and juice were performed, and those applied directly in stem provided the best results. Prediction models for sugar cane stem determinations with a single 60 s irradiation using portable X-ray fluorescence equipment allows estimating the % sucrose, % fiber, and POL simultaneously. Average relative deviations in the prediction step of around 8% are acceptable if considering that field measurements were done. These results may indicate the best period to cut a particular crop as well as for evaluating the quality of sugar cane for the sugar and alcohol industries.

A comparative study of the purification of betanin

Betanin is a natural pigment with antioxidant properties used as a food colourant. This work describes the spectrophotometric and chromatographic quantification of betanin (2S/15S) and its epimer isobetanin (2S/15R) in fresh beetroot juice, food-grade beetroot powder and betanin standard diluted in dextrin. Absorption spectra of all three samples were deconvoluted using a mixed three-function model. Food-grade beetroot powder has the largest amount of violet-red impurities, probably formed during processing. The purification of betanin from these complex matrices was carried out by seven different methods. Ion exchange chromatography was the most efficient method for the purification of betanin from all samples; however, fractions contain high amounts of salt. Reversed-phase HPLC as well as reversed-phase column chromatography also produced good results at a much faster rate. The longer retention time of isobetanin when compared to betanin in reversed-phase conditions has been investigated by means of quantum-mechanical methods. (C) 2011 Elsevier Ltd. All rights reserved.

Kinetic of water diffusion and color stability of a resin composite as a function of the curing tip distance

The influence of curing tip distance and storage time in the kinetics of water diffusion (water sorption-W SP, solubility-W SB, and net water uptake) and color stability of a composite were evaluated. Composite samples were polymerized at different distances (5, 10, and 15 mm) and compared to a control group (0 mm). After desiccation, the specimens were stored in distilled water to evaluate the water diffusion over a 120-day period. Net water uptake was calculated (sum of WSP and WSB). The color stability after immersion in a grape juice was compared to distilled water. Data were submitted to three-way ANOVA/Tukey's test (α = 5%). The higher distances caused higher net water uptake (p < 0.05). The immersion in the juice caused significantly higher color change as a function of curing tip distance and the time (p < 0.05). The distance of photoactivation and storage time provide the color alteration and increased net water uptake of the resin composite tested.

Guava pomace: a new source of anti-inflammatory and analgesic bioactives

Abstract Background Guava pomace is an example of the processing waste generated after the manufacturing process from the juice industry that could be a source of bioactives. Thus, the present investigation was carried out in order to evaluate the anti-inflammatory and antinociceptive potential and determinate the main phenolic compounds of a guava pomace extract (GPE). Methods The anti-inflammatory activity was evaluated by carrageenan, dextran, serotonin, histamine-induced paw edema and neutrophils migration in the peritoneal cavity models. Acetic acid-induced abdominal writhing and formalin test were performed to investigate the antinociceptive effects. In addition, the content of total phenolic and of individual phenolic compounds was determined by GC/MS. Results GPE showed anti-inflammatory activity by carrageenan, dextran, serotonin, histamine-induced paw edema and neutrophils migration in the peritoneal cavity models (p < 0.05). GPE also demonstrated antinociceptive activity by acetic acid-induced abdominal writhing and formalin test (p < 0.05). The total phenolic value was 3.40 ± 0.09 mg GAE/g and epicatechin, quercetin, myricetin, isovanilic and gallic acids were identified by GC/MS analysis. Conclusions The presence of bioactive phenolic compounds as well as important effects demonstrated in animal models suggest that guava pomace could be an interesting source of anti-inflammatory and analgesic substances.

Metabolismo di oligosaccaridi prebiotici in Bifidobacterium per il potenziale sviluppo di nuovi prodotti alimentari funzionali

The growth and the metabolism of Bifidobacterium adolescentis MB 239 fermenting GOS, lactose, galactose, and glucose were investigated. An unstructerd unsegregated model for growth of B. adolescentis MB 239 in batch cultures was developed and kinetic parameters were calculated with a Matlab algorithm. Galactose was the best carbon source; lactose and GOS led to lower growth rate and cellular yield, but glucose was the poorest carbon source. Lactate, acetate and ethanol yields allowed calculation of the carbon fluxes toward fermentation products. Similar distribution between 3- and 2-carbon products was observed on all the carbohydrates (45 and 55%, respectively), but ethanol production was higher on glucose than on GOS, lactose and galactose, in decreasing order. Based on the stoichiometry of the fructose 6-phosphate shunt and on the carbon distribution among the products, ATP yield was calculated on the different carbohydrates. ATP yield was the highest on galactose, while it was 5, 8, and 25% lower on lactose, GOS, and glucose, respectively. Therefore, a correspondance among ethanol production, low ATP yields, and low biomass production was established demonstrating that carbohydrate preferences may result from different sorting of carbon fluxes through the fermentative pathway. During GOS fermentation, stringent selectivity based on the degree of polymerization was exhibited, since lactose and the trisaccharide were first to be consumed, and a delay was observed until longer oligosaccharides were utilized. Throughout the growth on both lactose and GOS, galactose accumulated in the cultural broth, suggesting that β-(1-4) galactosides can be hydrolysed before they are taken up. The physiology of Bifidobacterium adolescentis MB 239 toward xylooligosaccharides (XOS) was also studied and our attention was focused on an extracellular glycosyl-hydrolase (β-Xylosidase) expressed by a culture of B. adolescentis grown on XOS as sole carbon source. The extracellular enzyme was purified from the the supernatant, which was dialyzed and concentrated by ultrafiltration. A two steps purification protocol was developed: the sample was loaded on a Mono-Q anion exchange chromatography and then, the active fractions were pooled and β-Xylosidase was purified by gel filtration chromatography on a Superdex-75. The enzyme was characterized in many aspects. β- Xylosidase was an homo-tetramer of 160 kDa as native molecular mass; it was a termostable enzyme with an optimum of temperature at 53 °C and an optimum of pH of 6.0. The kinetics parameter were calculated: km = 4.36 mM, Vmax = 0.93 mM/min. The substrate specificity with different di-, oligo- and polysaccharides was tested. The reactions were carried out overnight at pH 7 and at the optimum of temperature and the carbohydrates hydrolysis were analyzed by thin layer chromatography (TLC). Only glycosyl-hydrolase activities on XOS and on xylan were detected, whereas sucrose, lactose, cellobiose, maltose and raffinose were not hydrolyzed. It’s clearly shown that β-Xylosidase activity was higher than the Xylanase one. These studies on the carbohydrate preference of a strain of Bifidobacterium underlined the importance of the affinity between probiotics and prebiotics. On the basis of this concept, together with Barilla G&R f.lli SpA, we studied the possibility to develop a functional food containing a synbiotic. Three probiotic strains Lactobacillus plantarum BAR 10, Streptococcus thermophilus BAR 20, and Bifidobacterium lactis BAR 30 were studied to assess their suitability for utilization in synbiotic products on the basis of antioxidative activity, glutathione production, acid and bile tolerance, carbohydrates fermentation and viability in food matrices. Bile and human gastric juice resistance was tested in vitro to estimate the transit tolerance in the upper gastrointestinal tract. B. lactis and L. plantarum were more acid tolerant than S. thermophilus. All the strains resisted to bile. The growth kinetics on 13 prebiotic carbohydrates were determined. Galactooligosaccharides and fructo-oligosaccharides were successfully utilized by all the strains and could be considered the most appropriate prebiotics to be used in effective synbiotic formulations. The vitality of the three strains inoculated in different food matrices and maintained at room temperature was studied. The best survival of Lactobacillus plantarum BAR 10, Streptococcus thermophilus BAR 20, and Bifidobacterium lactis BAR 30 was found in food chocolate matrices. Then an in vivo clinical trial was carried out for 20 healthy volunteers. The increase in faecal bifidobacteria and lactobacilli populations and the efficacy of the pre-prototype was promising for the future develop of potential commercial products.

Sviluppo di un metodo elettrochimico per la determinazione della capacità antiossidante

The aim of the present thesis, carried out at the Analytical Group of the Faculty of Industrial Chemistry in Bologna, is to develop a new electrochemical method for the determination of the Antioxidant Capacity (AOC). The approach is based on the deposition of a non-conducting polymeric film on the working electrode surface and the following exposition to the radicals OH· produced by H2O2 photolysis. The strongly oxidant action of hydroxyl radicals degrades, causing an increase of the Faradic current, relevant to the redox couple [Ru(NH3)6]2+/3+ monitored by cyclic voltammetry(CV); the presence of an antioxidant compound in solution slows down the radical action, thus protecting the polymeric film and blocking the charge transfer. The parameter adopted for the quantification of the AOC, was the induction time, called also lag phase, which is the time when the degradation of the film starts. Five pure compounds, among most commonly antioxidant, were investigated : Trolox®(an analogue water-soluble of vitamin E), (L)-ascorbic acid, gallic acid, pyrogallol and (-)- epicatechin. The AOC of each antioxidant was expressed by TEAC index (Trolox® Equivalent Antioxidant Capacity), calculated from the ratio between the slope of the calibration curve of the target compound and the slope of the calibration curve of Trolox®. The results from the electrochemical method, have been compared with those obtained from some other standardized methods, widely employed. The assays used for the comparison, have been: ORAC, a spectrofluorimetric method based on the decrease of fluorescein emission after the attack of alkylperoxide radicals, ABTS and DPPH that exploit the decoloration of stable nitrogen radicals when they are reduced in presence of an antioxidant compound and, finally, a potentiometric method based on the response of the redox couple [Fe(CN)6]3-/ [Fe(CN)6]4-. From the results obtained from pure compounds, it has been found that ORAC is the methodology showing the best correlation with the developed electrochemical method, maybe since similar radical species are involved. The comparison between the considered assays, was also extended to the analysis of a real sample of fruit juice. In such a case the TEAC value resulting from the electrochemical method is higher than those from standardized assays.

Development of instrumental and sensory analytical methods of food obtained by traditional and emerging technologies

The consumer demand for natural, minimally processed, fresh like and functional food has lead to an increasing interest in emerging technologies. The aim of this PhD project was to study three innovative food processing technologies currently used in the food sector. Ultrasound-assisted freezing, vacuum impregnation and pulsed electric field have been investigated through laboratory scale systems and semi-industrial pilot plants. Furthermore, analytical and sensory techniques have been developed to evaluate the quality of food and vegetable matrix obtained by traditional and emerging processes. Ultrasound was found to be a valuable technique to improve the freezing process of potatoes, anticipating the beginning of the nucleation process, mainly when applied during the supercooling phase. A study of the effects of pulsed electric fields on phenol and enzymatic profile of melon juice has been realized and the statistical treatment of data was carried out through a response surface method. Next, flavour enrichment of apple sticks has been realized applying different techniques, as atmospheric, vacuum, ultrasound technologies and their combinations. The second section of the thesis deals with the development of analytical methods for the discrimination and quantification of phenol compounds in vegetable matrix, as chestnut bark extracts and olive mill waste water. The management of waste disposal in mill sector has been approached with the aim of reducing the amount of waste, and at the same time recovering valuable by-products, to be used in different industrial sectors. Finally, the sensory analysis of boiled potatoes has been carried out through the development of a quantitative descriptive procedure for the study of Italian and Mexican potato varieties. An update on flavour development in fresh and cooked potatoes has been realized and a sensory glossary, including general and specific definitions related to organic products, used in the European project Ecropolis, has been drafted.

Isolierung und Identifizierung von wachstumsfördernden Substanzen für das weinrelevante Bakterium Oenococcus oeni aus Fruchtsäften und Blattextrakten

Neben Tomatensaft wurde eine Vielzahl von Säften und Blattextrakten als Medienzusätze auf Wachstumsförderung bei 30 verschiedenen Oenococcus oeni-Stämmen getestet. Es zeigte sich eine breite Wachstumsförderung bei allen Zusätzen mit Ausnahme von Zitronensaft, sodass die Wachstumsfaktoren keine tomatenspezifischen Inhaltsstoffe sein können und eher ubiquitär in der Pflanzenwelt vorkommen. Das Ausmaß der Wachstumsförderung war stammabhängig sehr unterschiedlich und Tomatensaft stellte keineswegs für alle Stämme den optimalen Medienzusatz dar. Durch Schälen der Früchte war eine für die Analytik hilfreiche Abtrennung schalenspezifischer Inhaltsstoffe möglich, wobei auch die Schalenextrakte großes Potential für die Suche nach Wachstumsfaktoren offenbarten und die Wichtigkeit einer Auftrennung der Frucht in die verschiedenen Fruchtbereiche betonte. Aus Tomatensaft konnte analytisch der anorganische Wachstumsfaktor Mangan identifiziert werden. Die größten Zelldichten der Oenokokken-Stämme wurden hierbei bei 67 µM und 34 mM Manganzusatz erreicht. Bei 13 von 20 getesteten Oenokokkenstämmen konnte bei Zusatz von 34 mM Mangan der Tomatensaft ersetzt werden, bei 4 Stämmen (z. B. Stamm B2) fehlten jedoch noch weitere Wachstumsfaktoren und bei 3 Stämmen (z. B. Stamm B120) kam es zu einem verfrühten Absterben. Da weitere Mineralstoffe sowie veraschte Säfte und Blattextrakte keinen positiven Einfluß auf die Oenokokken-Zelldichte hatten, wurde mittels semipräparativer HPLC nach zusätzlichen organischen Wachstumsfaktoren für den Stamm B2 gesucht. Hierzu wurde der nachfolgende Wachstums-Assay miniaturisiert und erfolgreich auf Microtiterplatten etabliert. Es gelang die Isolierung und Identifizierung eines wachstumsfördernden Trisaccharides aus Mangoschalen-Extrakt, das aus den Zuckern Glucose, Rhamnose und Arabinose bestand. Von den monomeren Zuckern erhöhte lediglich die Arabinose die Zelldichte, das Optimum lag bei 1,5 g/l. Auch aus Zitronenmesokarp-Extrakt war die Isolierung eines wachstumsfördernden arabinosehaltigen Disaccharides möglich, die Menge reichte jedoch noch nicht für eine genaue Identifizierung aus. Desweiteren erwies sich 1,5 g/l Cystein als wachstumsstimulierend. Ein Zusatz aller gefundenen Wachstumsfaktoren (34 mM Mangan, 1,5 g/l Arabinose und 1,5 g/l Cystein) ersetzte den Tomatensaft bei weiteren Oenokokken-Stämmen (z.B. Stamm B120) komplett, wobei bei allen Stämmen sogar eine schnellere Anzucht erfolgte. Neben dem Tomatensaft war auch der Zusatz von Hefeextrakt zum Grundmedium nicht mehr nötig, sodass ein neues vereinfachtes Medium für die Anzucht von Oenokokken mit komplexen Nährstoffansprüchen vorgeschlagen werden konnte. Lediglich beim Stamm B2 zeigte sich noch ein OD-Unterschied von 0,2 in der stationären Phase, der nach Adsorptionsversuchen an Polyvinylpolypyrrolidon auf noch unidentifizierte Polyphenole im Tomatensaft zurückzuführen ist. Aus grünem Tee erwies sich das Polyphenol Epigallocatechingallat (EGCG) konzentrationsabhängig sowohl als Hemmstoff (>550 mg/l EGCG) als auch Wachstumsfaktor (400-500 mg/l EGCG) für den Oenokokken-Stamm B2. Der hemmende als auch der fördernde Einfluss auf das Wachstum wurde mittels Sytox/DAPI-Färbung bestätigt. Der sogenannte „Tomatensaft-Faktor“ ist also nicht eine spezielle Substanz, sondern das synergistische Zusammenwirken mehrerer einfacher Substanzen wie Mineralstoffe, Aminosäuren, Kohlenhydrate und Polyphenole. Auch sind die Oenokokken-Stämme bezüglich ihres Nährstoffbedarfes sehr unterschiedlich, sodass für jeden Stamm einzeln das optimale Substratspektrum ermittelt werden muss.

1st and 2nd Generation Ethanol from Biomass Crops

In chapter 1 and 2 calcium hydroxide as impregnation agent before steam explosion of sugarcane bagasse and switchgrass, respectively, was compared with auto-hydrolysis, assessing the effects on enzymatic hydrolysis and simultaneous saccharification and fermentation (SSF) at high solid concentration of pretreated solid fraction. In addition, anaerobic digestion of pretreated liquid fraction was carried out, in order to appraise the effectiveness of calcium hydroxide before steam explosion in a more comprehensive way. In As water is an expensive input in both cultivation of biomass crops and subsequent pretreatment, Chapter 3 addressed the effects of variable soil moisture on biomass growth and composition of biomass sorghum. Moreover, the effect of water stress was related to the characteristics of stem juice for 1st generation ethanol and structural carbohydrates for 2nd generation ethanol. In the frame of chapter 1, calcium hydroxide was proven to be a suitable catalyst for sugarcane bagasse before steam explosion, in order to enhance fibre deconstruction. In chapter 2, effect of calcium hydroxide on switchgrass showed a great potential when ethanol was focused, whereas acid addition produced higher methane yield. Regarding chapter 3, during crop cycle the amount of cellulose, hemicellulose and AIL changed causing a decrease of 2G ethanol amount. Biomass physical and chemical properties involved a lower glucose yield and concentration at the end of enzymatic hydrolysis and, consequently, a lower 2G ethanol concentration at the end of simultaneous saccharification and fermentation, proving that there is strong relationship between structure, chemical composition, and fermentable sugar yield. The significantly higher concentration of ethanol at the early crop stage could be an important incentive to consider biomass sorghum as second crop in the season, to be introduced into some agricultural systems, potentially benefiting farmers and, above all, avoiding the exacerbation of the debate about fuel vs food crops.

Mikrobielle Synthese von Biopolymeren aus der nachwachsenden Rohstoffquelle Weizenstroh

Weizenstroh als erneuerbare Ressource zur Produktion von Biopolymeren und wichtigen Grundchemikalien stellt eine ökologisch sinnvolle Alternative dar. Durch die vom PFI durchgeführte Thermodruckhydrolyse konnte das Weizenstroh und die darin enthaltenen Zucker fast vollständig mobilisiert werden. Ein umfangreiches Screening nach Organismen, welche die Zucker des Weizenstrohs verwerten konnten, ergab, dass einige wenige Stämme zur PHB-Bildung aus Xylose befähigt waren (10 %). Zur PHB-Synthese aus Glucose waren indes ca. doppelt so viele Organismen in der Lage (20 %). Zwei der insgesamt 118 untersuchten Organismen zeigten besonders gute PHB-Bildung sowohl mit Xylose als auch mit Glucose als Substrat. Dabei handelte es sich um die hauseigenen Stämme Bacillus licheniformis KHC 3 und Bacillus megaterium KNaC 2. Nach Enttoxifizierung der hemicellulosischen Fraktion konnte diese als C-Quelle im Mineral Medium eingesetzt werden. Burkholderia sacchari DSM 17165 und Hydrogenophaga pseudoflava DSM 1034, sowie die hauseigenen Isolate Bacillus licheniformis KHC 3 und Bacillus megaterium KNaC 2 wurden für die Synthese von PHB aus der hemicellulosischen Fraktion verwendet. Die Zucker der hemicellulosischen Fraktion (Xylose, Glucose, Arabinose) konnten durch diese Organismen zur PHB-Synthese genutzt werden. Hierbei stellte sich heraus, dass die beiden Bacillus-Stämme besser zur Produktion von PHB aus dem hemicellulosischen Hydrolysat geeignet waren als die Stämme der DSMZ. Die alternative Umsetzung der im hemicellulosischem Hydrolysat enthaltenen Zucker (Xylose, Glucose und Arabinose) in die wichtigen Grundchemikalien Lactat und Acetat konnte durch die Verwendung von heterofermentativen Milchsäurebakterien verwirklicht werden. Die Bildung dieser wichtigen Grundchemikalien stellt eine interessante Alternative zur PHB-Synthese dar. Die Menge an teuren Zusätzen wie Tomatensaft, welcher für das Wachstum der MSB essentiell war, konnte reduziert werden. Die Glucose der zweiten Fraktion des Weizenstrohs, der cellulosischen Fraktion, konnte ebenfalls durch den Einsatz von Mikroorganismen in PHB umgewandelt werden. Kommerzielle Cellulasen der Firma Novozymes konnten große Mengen an Glucose (≥10 g/l) aus der cellulosischen Fraktion freisetzen. Diese freie Glucose wurde mit Hilfe von Cupriavidus necator DSM 545, Cupriavidus necator NCIMB 11599, Bacillus licheniformis KHC 3 und Bacillus megaterium KNaC 2 zu PHB fermentiert. Wie auch beim hemicellulosischen Hydrolysat konnten hier die beiden Bacillus-Stämme die besten Ergebnisse erzielen. Bei ihnen machte die PHB mehr als die Hälfte der Trockenmasse aus. Die Abtrennung des Zielprodukts ohne die Verwendung von umweltschädlichen Lösungsmitteln wurde durch die Lyse der Zielzellen durch eigens isolierte Enzyme aus Streptomyceten verwirklicht. Die Zelllyse durch die Enzyme aus Streptomyces globisporus subsp. caucasius DSM 40814 und Streptomyces albidoflavus DSM 40233 war erfolgreich und zeigte vor allem bei den Bacillen hohe Wirkung (83 % und 99 % Zelllyse). Bei dem Gram-negativen Organismus Cupriavidus necator DSM 428 konnte die anfangs niedrige Zelllyse von 38 % durch Ultraschallbehandlung auf ca. 75 % erhöht werden.

Thickness of softened human enamel removed by toothbrush abrasion: an in vitro study

The aim of the study was to assess the thickness of softened enamel removed by toothbrushing. Human enamel specimens were indented with a Knoop diamond. Softening was performed with citric acid or orange juice. The specimens were brushed in a brushing machine with a manual soft toothbrush in toothpaste slurry or in artificial saliva. Enamel loss was calculated from the change in indentation depth of the same indent before and after abrasion. Mean surface losses (95% confidence interval) were recorded in treatment groups (in nanometers): (1) citric acid, abrasion with slurry = 339 (280-398); (2) citric acid, abrasion with artificial saliva = 16 (5-27); (3) orange juice, abrasion with slurry = 268 (233-303); (4) orange juice, abrasion with artificial saliva = 14 (5-23); (5) no softening, abrasion with slurry = 28 (10-46). The calculated thickness of the softened enamel varied between 254 and 323 nm, depending on the acid used.