Direct shear testing on unsaturated silty soils to investigate the effects of drying and wetting on shear strength parameters at low suction

A modified conventional direct shear device was used to measure unsaturated shear strength of two silty soils at low suction values (0 ~ 50 kPa) that were achieved by following drying and wetting paths of soil water characteristic curves (SWCCs). The results revealed that the internal friction angle of the soils was not significantly affected by either the suction or the drying wetting SWCCs. The apparent cohesion of soil increased with a decreasing rate as suction increased. Shear stress-shear displacement curves obtained from soil specimens subjected to the same net normal stress and different suction values showed a higher initial stiffness and a greater peak stress as suction increased. A soil in wetting exhibited slightly higher peak shear stress and more contractive volume change behavior than that of soil in drying at the same net normal stress and suction.

Yield of synthetic backcross-derived lines in rainfed environments of Australia

Wheat is one of the major food crops in the world. It is Australia's largest crop and most important agricultural commodity. In Australia the crop is grown under rainfed conditions with inherently important regional environmental differences; wheat growing areas are characterized by winter dominant rainfall in southern and western Australia and summer rainfall in northern Australia. Maximizing yield potential across these diverse regions is dependent upon managing, either genetically or agronomically, those factors in the environment that limit yield. The potential of synthetic backcross lines (SBLs) to increase yield in the diverse agroecological zones of Australia was investigated. Significant yield advantages were found for many of the SBLs across diverse environments. Depending on the environment, the yield of the SBLs ranged from 8% to 30% higher than the best local check in Australia. Apart from adaptation to semiarid water stressed conditions, some SBLs were also found to be significantly higher yielding under more optimal (irrigated) conditions. The four testing environments were classified into two groups, with the northern and southern environments being in separate groups. An elite group of SBLs was identified that exhibited broad adaptation across all diverse Australian environments included in this study. Other SBLs showed specific adaptation to either northern or southern Australia. This study showed that SBLs are likely to provide breeders with the opportunity to significantly improve wheat yield beyond what was previously possible in a number of diverse production environments.

Gauge theory of a group of diffeomorphisms. I. General principles

Any (N+M)-parameter Lie group G with an N-parameter subgroup H can be realized as a global group of diffeomorphisms on an M-dimensional base space B, with representations in terms of transformation laws of fields on B belonging to linear representations of H. The gauged generalization of the global diffeomorphisms consists of general diffeomorphisms (or coordinate transformations) on a base space together with a local action of H on the fields. The particular applications of the scheme to space-time symmetries is discussed in terms of Lagrangians, field equations, currents, and source identities. Journal of Mathematical Physics is copyrighted by The American Institute of Physics.

Antimicrobial susceptibility testing of Brachyspira intermedia and Brachyspira pilosicoli isolates from Australian chickens

Susceptibilities of predominantly Australian isolates of the pathogenic intestinal spirochaetes Brachyspira intermedia (n=25) and Brachyspira pilosicoli (n=17) from chickens were tested in agar dilution against four concentrations each of the antimicrobials tiamulin, lincomycin, tylosin, metronidazole, tetracycline and ampicillin. Based on available minimum inhibitory concentration (MIC) breakpoint values for Brachyspira hyodysenteriae or other Gram-negative enteric veterinary pathogens, isolates of both species generally were susceptible to tiamulin, lincomycin, metronidazole and tetracycline. Although not classed as resistant, four isolates of B. intermedia had an elevated MIC range for tiamulin (1 to 4 mg/l), 11 isolates of B. intermedia and five of B. pilosicoli had an elevated MIC range for lincomycin (10 to 50 mg/l), one isolate of B. pilosicoli had an elevated MIC range for tetracycline (10 to 20 mg/l), and one isolate of B. intermedia and five of B. pilosicoli had an elevated MIC range for ampicillin (10 to 50 mg/l). A clear lack of susceptibility to tylosin (MIC >4 mg/l) was seen in 11 isolates each of B. intermedia and B. pilosicoli, and to ampicillin (MIC >32 mg/l) in two isolates of B. pilosicoli. These data suggest that some resistance to common antimicrobials exists among intestinal spirochetes obtained from laying hens and supports the need of MIC data for clinical isolates before any treatment is considered.

A visual profile of Queensland Indigenous children

Purpose Little is known about the prevalence of refractive error, binocular vision, and other visual conditions in Australian Indigenous children. This is important given the association of these visual conditions with reduced reading performance in the wider population, which may also contribute to the suboptimal reading performance reported in this population. The aim of this study was to develop a visual profile of Queensland Indigenous children. Methods Vision testing was performed on 595 primary schoolchildren in Queensland, Australia. Vision parameters measured included visual acuity, refractive error, color vision, nearpoint of convergence, horizontal heterophoria, fusional vergence range, accommodative facility, AC/A ratio, visual motor integration, and rapid automatized naming. Near heterophoria, nearpoint of convergence, and near fusional vergence range were used to classify convergence insufficiency (CI). Results Although refractive error (Indigenous, 10%; non-Indigenous, 16%; p = 0.04) and strabismus (Indigenous, 0%; non-Indigenous, 3%; p = 0.03) were significantly less common in Indigenous children, CI was twice as prevalent (Indigenous, 10%; non-Indigenous, 5%; p = 0.04). Reduced visual information processing skills were more common in Indigenous children (reduced visual motor integration [Indigenous, 28%; non-Indigenous, 16%; p < 0.01] and slower rapid automatized naming [Indigenous, 67%; non-Indigenous, 59%; p = 0.04]). The prevalence of visual impairment (reduced visual acuity) and color vision deficiency was similar between groups. Conclusions Indigenous children have less refractive error and strabismus than their non-Indigenous peers. However, CI and reduced visual information processing skills were more common in this group. Given that vision screenings primarily target visual acuity assessment and strabismus detection, this is an important finding as many Indigenous children with CI and reduced visual information processing may be missed. Emphasis should be placed on identifying children with CI and reduced visual information processing given the potential effect of these conditions on school performance

Grower group case study on new farming practices in the Herbert region, Australia

Growers working together have proven to be a successful method for improving the utilization of farm resources and accelerating the adoption of the Sugar Yield Decline Joint Venture principles (SYDJV). The Pinnacle Precision Farming Group was formed in 2004 with the aim to bring together the ideas, knowledge and resources of growers in the Herbert region. Along with their common interest in controlled traffic, minimal tillage and crop rotations, the grower group utilize a farm machinery contractor to provide some of their major farming operations. This paper provides an insight into the changes made by the Pinnacle Precision Farming Group and their journey to adopt the new farming system practices. This paper also details the changes made by the group machinery contractor and a comparison of the old and new farming systems used by a group member. A focus point of the document is the impact of the new farming system on the economic, social and environmental components of the farming business. Analysis of the new farming system with a legume crop rotation revealed an increase in the farm gross margin by AU$22 024 and, in addition, a reduction in tractor operation time by 38% across the whole farm. This represents a return on marginal capital of 14.68 times the original capital outlay required by the group member. Using the new farming system without a legume crop will still improve the group members whole of farm gross margin by AU$6 839 and reduce tractor operation time by 43% across the whole farm. The Pinnacle Precision Farming group recognize the need to continually improve their farming businesses and believe that the new farming system principles are critical for the long term viability of the industry. [U$1 = AU$1.19].

Measuring the traction profile on sportsfields: Equipment development and testing

Traction is recognised as an important component of the overall playability and safety of a sportsfield. It relates to the "grip", or footing, provided through an athlete's shoe when in contact with the surface, and is normally measured by the torque generated when a weighted studded disc apparatus is dropped onto the turf and twisted manually. This paper describes the development of an automated traction tester, which mechanises the dropping and twisting of the weighted studded disc. By standardising these operational stages, more repeatable and reliable results can be expected than from the original hand-operated design where positioning of the disc and speed of rotation are controlled manually and so can vary from one measurement to the next. As well as measuring the maximum torque reached during rotation of the studded disc, the automated traction tester generates a profile of torque showing changes over time and calculates the angle through which the studded disc moved before reaching maximum torque. These aspects are now covered by a utility patent (PAT/AU/2004270767). Use of the automated traction tester is illustrated by comparative data for a range of warm-season turfgrasses, by comparisons of traction under different surface conditions generated by wear on Cynodon dactylon cultivars, and by the effects of environment, management and playing patterns on traction across a multi-use sports stadium.

Optical peanut yield monitor: Development and testing

An optical peanut yield monitor was developed, fabricated, and field-tested. The overall system includes an optical mass-flow sensor, a GPS receiver, and a data acquisition system. The concept for the mass-flow sensor is based on that of the cotton yield-monitor sensor developed previously by Thomasson and Sui (2000). A modified version of the sensor was designed to be specific to peanut mass-flow measurement. Field testing of the peanut yield monitor was conducted in Australia during the May 2003 harvest. After subsequent minor modifications, the system was more extensively tested in Mississippi in October of 2003 and November of 2004. Test results showed that the output of the peanut mass-flow sensor was very strongly correlated with the harvested load weight, and the system's performance was stable and reliable during the tests.

Testing approximate theories of first-order phase transitions on the two-dimensional Potts model

The two-dimensional,q-state (q>4) Potts model is used as a testing ground for approximate theories of first-order phase transitions. In particular, the predictions of a theory analogous to the Ramakrishnan-Yussouff theory of freezing are compared with those of ordinary mean-field (Curie-Wiess) theory. It is found that the Curie-Weiss theory is a better approximation than the Ramakrishnan-Yussouff theory, even though the former neglects all fluctuations. It is shown that the Ramakrishnan-Yussouff theory overestimates the effects of fluctuations in this system. The reasons behind the failure of the Ramakrishnan-Yussouff approximation and the suitability of using the two-dimensional Potts model as a testing ground for these theories are discussed.

The complexities of knowing what it is you are trapping

The effectiveness of any trapping system is highly dependent on the ability to accurately identify the specimens collected. For many fruit fly species, accurate identification (= diagnostics) using morphological or molecular techniques is relatively straightforward and poses few technical challenges. However, nearly all genera of pest tephritids also contain groups of species where single, stand-alone tools are not sufficient for accurate identification: such groups include the Bactrocera dorsalis complex, the Anastrepha fraterculus complex and the Ceratitis FAR complex. Misidentification of high-impact species from such groups can have dramatic consequences and negate the benefits of an otherwise effective trapping program. To help prevent such problems, this chapter defines what is meant by a species complex and describes in detail how the correct identification of species within a complex requires the use of an integrative taxonomic approach. Integrative taxonomy uses multiple, independent lines of evidence to delimit species boundaries, and the underpinnings of this approach from both the theoretical speciation literature and the systematics/taxonomy literature are described. The strength of the integrative approach lies in the explicit testing of hypotheses and the use of multiple, independent species delimitation tools. A case is made for a core set of species delimitation tools (pre- and post-zygotic compatibility tests, multi-locus phylogenetic analysis, chemoecological studies, and morphometric and geometric morphometric analyses) to be adopted as standards by tephritologists aiming to resolve economically important species complexes. In discussing the integrative approach, emphasis is placed on the subtle but important differences between integrative and iterative taxonomy. The chapter finishes with a case study that illustrates how iterative taxonomy applied to the B. dorsalis species complex led to incorrect taxonomic conclusions, which has had major implications for quarantine, trade, and horticultural pest management. In contrast, an integrative approach to the problem has resolved species limits in this taxonomically difficult group, meaning that robust diagnostics are now available.

Topochemical photodimerization of 7-acetoxycoumarin: the acetoxy group as a steering agent

Among the various substituted coumarins investigated only 7-acetoxycoumarin is observed to photodimerize topochemically in the crystalline state and this observation may be of importance in the context of "crystal engineering".

Rationale of Length Scale-Down Model Span Testing of Transmission Lines

Length scale-down (LS) model tests have been traditionally employed for laboratory studies on aeolian vibration of transmission line conductors. The span adopted is normally 30 m and is recommended by the relevant Indian, as well as other, standards. The traditionally adopted length of the LS model is reexamined herein to establish the rationale behind the choice. Based on the theoretical studies discussed, certain guidelines for the choice of model span of conductor are emphasized. In addition, the adequacy of the LS span as a tool for predicting the performance of the full span is reestablished.

Käsityksistä ajatuksen poluille : Ammattikorkeakoulun tutkimus- ja kehitystoiminnan kehittäminen

This study deals with the formation of the idea of research and development (r&d) activity at one particular university of applied sciences in Finland. In this study I proceed from examining the conceptions of management regarding r&d-activities to exploring the development of the complex concept that guides these r&d-activities. The aim of this study is, first, to describe conceptions of r&d-activities, and then, second, to describe the formation of a new concept for r&d-activities in one field of study at the university of applied sciences. I used phenomenographic analysis to elucidate the conceptions and collected the data in interviews of personnel (22) who belong to the management of the university of applied sciences. The data for analysing the obstacles faced and the ways of overcoming them during the formation process of the new concept consist of the video-recorded material from ten change laboratory sessions held for the specific field of study at the university of applied sciences. In researching the formation of the concept of the activity, such research and analysis methods are used in which the concept is understood as a material construction, and with the help of which one can work out the formation of the concept during the development process. When the systematic development of the r&d-work was underway, the management of the university of applied sciences held differing views regarding the content, target, factors and organisation of the r&d-activities, as well as regarding the position of dissertations as a part of r&d-activity. Obstacles for developing rd concerned the unclear object and outcomes of the new activity, not having the tools (such as adequate know-how) for the new activity and not having found the necessary solutions for the distribution of work. In addition the rules that quide the activities of the university of applied sciences did not support working according to the new way. To improve r&d-activity, the school’s management defined three development strategies to encourage adequate rd-activity to support working life, regional development and learning. The strategies were based on the expansion of existing methods, such as service activities, dissertation work and the research activities of the teachers. Of the three possible routes, the concept of dissertation in this study was expanded to integrate the services of organisation development and the occupational growth of the students. A group of teachers in the field of social and health studies participated in the development work. The change laboratory method was used as a tool for this work. Analysis of the cognitive trails indicated that, in addition to the cycle of expansive learning activities, microcycles with different purposes can exist. According to Cussins (1992), something already in existence in each microcycle is destabilised, and something else is stabilised to replace it. In this study three microcycles were identified, during which the teachers first destabilised the existing concepts of dissertation work that guided their thinking, and then began to use new concepts to structure their thinking. Secondly, they undermined the existing concepts with material structure that defined their practical work, and developed new practical models to replace them. Thirdly, the problems accumulating in researching and testing the new activities caused the developers to destabilise the r&d-strategies of the university of applied sciences and to define a new conceptual model for r&d-work in the field. During this third cycle, the teachers developed a research arena model, which was a significant expansive innovation. In the cognitive trails developing the new concept for the r&d-activity, the teachers indeed faced the obstacles the management had described as their conceptions. These obstacles manifested themselves as contradictions. During the development process, the nature of the obstacles (i.e. contradictions) changed as the development proceeded. Solving the first and second degree contradictions highlighted the third and fourth degree contradictions. To overcome the obstacles, the teachers had to to articulate the value and motive of the development work throughout the development process. Developing the new concept for r&d-activity required many reconfigurations of practical solutions to overcome the obstacles. Developing the new concept for r&d-activity, both at the level of representations and of new practices, requires universities of applied sciences to adopt new methods in which the actors are partake in construction of new concepts of activity through adequate discussion, analysis and debate. R&d -activity can progress, if instead of implementing partial solutions, the totality of the activities (i.e. the group of partial solutions acting together) will be constructed. The development of the activity system requires many simultaneous changes as well as wide-ranging know-how and discussion related to these changes. What is perhaps most important, however, is that the group of developers mature into a determined collective actor which can engage in many agentive actions. The development of the agency is fundamental to progress.

Truckies and workplace health promotion: Targeting a hard-to-reach group

- Introduction Research identifies truck drivers as being at high risk of chronic disease. For most truck drivers their workplace is their vehicle. Truck drivers’ health is impacted by the limitations of this unique working environment, including reduced opportunities for physical activity and the intake of healthy foods. Workplaces are widely recognised as effective platforms for health promotion. However, the effectiveness of traditional and contemporary health promotion interventions in truck drivers’ novel workplace is unknown. - Methods This project worked with six transport industry workplaces in Queensland, Australia over a two-year period. Researchers used Participatory Action Research (PAR) processes to engage truck drivers and workplace managers in the implementation and evaluation of six workplace health promotion interventions. These interventions were designed to support truck drivers to increase their physical activity and access to healthy foods at work. They included traditional health promotion interventions such as a free fruit initiative, a ten thousand steps challenge, personal health messages and workplace posters, and a contemporary social media intervention. Participants were engaged via focus groups, interviews and mixed-methods surveys. - Results The project achieved positive changes in truck drivers’ health knowledge and health behaviours, particularly related to nutrition. There were positive changes in truck drivers’ self-reported health rating, body mass index (BMI) and readiness to make health-related lifestyle changes. There were also positive changes in truck drivers reporting their workplace as a key source of health information. These changes were underpinned by a positive shift in the culture of participating workplaces. Truck drivers’ perceptions of their workplace valuing, encouraging, modelling and facilitating healthy nutrition and physical activity behaviours improved. PAR processes enabled researchers to develop relationships with workplace managers, contextualise interventions and deliver rigorous outcomes. Despite the novelty of truck drivers’ mobile workplace, traditional health promotion interventions were more effective than contemporary ones. - Conclusion In this workplace health promotion project targeting a ‘hard-to-reach’ group of truck drivers, a combination of well-designed traditional workplace interventions and the PAR process resulted in positive health outcomes.

Optimized group replacement scheduling for water pipeline network

Replacement of deteriorated water pipes is a capital-intensive activity for utility companies. Replacement planning aims to minimize total costs while maintaining a satisfactory level of service and is usually conducted for individual pipes. Scheduling replacement in groups is seen to be a better method and has the potential to provide benefits such as the reduction of maintenance costs and service interruptions. However, developing group replacement schedules is a complex task and often beyond the ability of a human expert, especially when multiple or conflicting objectives need to be catered for, such as minimization of total costs and service interruptions. This paper describes the development of a novel replacement decision optimization model for group scheduling (RDOM-GS), which enables multiple group-scheduling criteria by integrating new cost functions, a service interruption model, and optimization algorithms into a unified procedure. An industry case study demonstrates that RDOM-GS can improve replacement planning significantly and reduce costs and service interruptions.