Obtenção e caracterização de um compósito polimérico de matriz poliéster e reforço/carga de tecido plano de algodão

He was obtained and studied the feasibility of using TPA (Tissue Cotton Plan) screen type, for bagging, with a weight of 207.9 g / m2 in a composite of orthophthalic crystal polyester resin matrix. The process for obtaining the composite was tested against the maximum number of layers that could be used without compromising the processability and manufacturing of CPs in compression mold. Five configurations / formulations were selected and tested at 1, 4, 8, 10 and 12 layers of cotton tissue - TPA. TPA was not subjected to chemical treatment, only by passing a mechanical washing process. The composite in its various configurations / formulations was characterized to determine its physical properties. The properties of the composite were higher viability resistance to bending, approaching the matrix and impact resistance, superiority in relation to the polyester resin. Another property that has shown good result compared to other composite has water absorption. Analyzing all the properties set the settings / formulations with higher viability were TA8 and TA10, by combining good processability and higher mechanical strength, with lower loss compared to polyester resin matrix. The composite showed lower mechanical behavior of the resin matrix for all the formulations studied except the impact resistance. The SEM showed a good adhesion between the layers of TPA and polyester resin matrix, without the presence of micro voids in the matrix confirming the efficient manufacturing process of the samples for characterization. The composite proposed proved to be viable for the fabrication of structures with low requests from mechanical stresses, and as demonstrated for the manufacture of solar and wind prototypes, and packaging, shelving, decorative items, crafts and shelves, with good visual appearance.

Obtenção e caracterização de um compósito polimérico de matriz poliéster e reforço/carga de tecido plano de algodão

He was obtained and studied the feasibility of using TPA (Tissue Cotton Plan) screen type, for bagging, with a weight of 207.9 g / m2 in a composite of orthophthalic crystal polyester resin matrix. The process for obtaining the composite was tested against the maximum number of layers that could be used without compromising the processability and manufacturing of CPs in compression mold. Five configurations / formulations were selected and tested at 1, 4, 8, 10 and 12 layers of cotton tissue - TPA. TPA was not subjected to chemical treatment, only by passing a mechanical washing process. The composite in its various configurations / formulations was characterized to determine its physical properties. The properties of the composite were higher viability resistance to bending, approaching the matrix and impact resistance, superiority in relation to the polyester resin. Another property that has shown good result compared to other composite has water absorption. Analyzing all the properties set the settings / formulations with higher viability were TA8 and TA10, by combining good processability and higher mechanical strength, with lower loss compared to polyester resin matrix. The composite showed lower mechanical behavior of the resin matrix for all the formulations studied except the impact resistance. The SEM showed a good adhesion between the layers of TPA and polyester resin matrix, without the presence of micro voids in the matrix confirming the efficient manufacturing process of the samples for characterization. The composite proposed proved to be viable for the fabrication of structures with low requests from mechanical stresses, and as demonstrated for the manufacture of solar and wind prototypes, and packaging, shelving, decorative items, crafts and shelves, with good visual appearance.

Efeito da adição de WC e Co na sinterização e propriedades mecânicas da alumina

Composites based on alumina (Al2O3), tungsten carbide (WC) and cobalt (Co) exhibit specific properties such as low density, high oxidation resistance, high melting point and high chemical inertia. That composite shows to be a promising material for application in various fields of engineering. In this work, the mechanical properties of the composite (Al2O3 – WC – Co), particularly density and hardness, were evaluated according to the effects of the variables of powder processing parameters, green compact and sintered. Powder composites with the composition of 80 wt% Al2O3, 18 wt% WC and 2 wt% Co were processed by high energy ball milling in a planetary mill for 50 hours as well as mixed by manual mixing in a glass vessel with the same proportion. Samples were collected (2, 10, 20, 30, 40 and 50 hours) during the milling process. Then, the powders were compacted in a cylindrical die with 5 mm in diameter in a uniaxial press with pressures of 200 and 400 MPa. The sintering was in two stages: first, the solid phase sintering was performed at 1126 and 1300 °C for 1 hour with a heating rate of 10 °C/min in a resistive furnace under argon atmosphere for green samples compacted in 200 and 400 MPa; the second sintering was performed on dilatometer in solid phase at 1300 °C for green sample compacted in 200 MPa, another sintering also was performed on dilatometer, this time in liquid phase at 1550 °C for green samples compacted in 200 and 400 MPa, with the same parameters used in resistive furnace. The raw materials were characterized by X – ray diffraction (XRD), X – ray fluorescence (XRF), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and laser particlemeter. The sintered samples were subjected to microhardness testing. The results showed that high energy milling achieved to the objectives regarding the particle size and the dispersion of composite phases. However, the hardness did not achieve to significant results, this is an indication that the composite has low fracture toughness.

Efeito da adição de WC e Co na sinterização e propriedades mecânicas da alumina

Composites based on alumina (Al2O3), tungsten carbide (WC) and cobalt (Co) exhibit specific properties such as low density, high oxidation resistance, high melting point and high chemical inertia. That composite shows to be a promising material for application in various fields of engineering. In this work, the mechanical properties of the composite (Al2O3 – WC – Co), particularly density and hardness, were evaluated according to the effects of the variables of powder processing parameters, green compact and sintered. Powder composites with the composition of 80 wt% Al2O3, 18 wt% WC and 2 wt% Co were processed by high energy ball milling in a planetary mill for 50 hours as well as mixed by manual mixing in a glass vessel with the same proportion. Samples were collected (2, 10, 20, 30, 40 and 50 hours) during the milling process. Then, the powders were compacted in a cylindrical die with 5 mm in diameter in a uniaxial press with pressures of 200 and 400 MPa. The sintering was in two stages: first, the solid phase sintering was performed at 1126 and 1300 °C for 1 hour with a heating rate of 10 °C/min in a resistive furnace under argon atmosphere for green samples compacted in 200 and 400 MPa; the second sintering was performed on dilatometer in solid phase at 1300 °C for green sample compacted in 200 MPa, another sintering also was performed on dilatometer, this time in liquid phase at 1550 °C for green samples compacted in 200 and 400 MPa, with the same parameters used in resistive furnace. The raw materials were characterized by X – ray diffraction (XRD), X – ray fluorescence (XRF), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and laser particlemeter. The sintered samples were subjected to microhardness testing. The results showed that high energy milling achieved to the objectives regarding the particle size and the dispersion of composite phases. However, the hardness did not achieve to significant results, this is an indication that the composite has low fracture toughness.

Obtenção e caracterização de um compósito de matriz polimérica com carga de resíduos vegetal proveniente do sabugo de milho

The feasibility of using the corn cob to obtain a polymer matrix composite was studied. To obtain the bran, corncob passed the drying process in a solar dryer, and was subsequently triturated in forage and to obtain the different particle sizes, by sieving. Three different grain sizes were used: fine particles (FP) size between 0,10 and 2mm; sized particles (PM) with sizes between 2,10 and 3,35 mm; large particles (PG) sizes between 3,45 and 4,10 mm. Using 20% of residue relative to the resin, the test samples were constructed for characterization of the composite, taking into account thermal and mechanical parameters. The main advantage of the proposed composite is that it has a low density, below the relative resin, about 1.06 kg / m³ for the PG. The composite showed a mechanical behavior less than of the resin to the grain sizes and for all formulations studied. Showed better results for the bending, reaching 25.3 MPa for the PG. The composite also showed be feasible for thermal applications, with thermal conductivity less than 0.21 W / m, ranking as insulation. In terms of homogeneity of the mixture, the most viable grain size is the PF, which also showed improved aesthetics and better processability. This composite can be used to make structures that do not require significant mechanical strength, such as tables, chairs, planks, and solar and wind prototypes, such as ovens and cookers and turbines blades.

Obtenção e caracterização de um compósito de matriz polimérica com carga de resíduos vegetal proveniente do sabugo de milho

The feasibility of using the corn cob to obtain a polymer matrix composite was studied. To obtain the bran, corncob passed the drying process in a solar dryer, and was subsequently triturated in forage and to obtain the different particle sizes, by sieving. Three different grain sizes were used: fine particles (FP) size between 0,10 and 2mm; sized particles (PM) with sizes between 2,10 and 3,35 mm; large particles (PG) sizes between 3,45 and 4,10 mm. Using 20% of residue relative to the resin, the test samples were constructed for characterization of the composite, taking into account thermal and mechanical parameters. The main advantage of the proposed composite is that it has a low density, below the relative resin, about 1.06 kg / m³ for the PG. The composite showed a mechanical behavior less than of the resin to the grain sizes and for all formulations studied. Showed better results for the bending, reaching 25.3 MPa for the PG. The composite also showed be feasible for thermal applications, with thermal conductivity less than 0.21 W / m, ranking as insulation. In terms of homogeneity of the mixture, the most viable grain size is the PF, which also showed improved aesthetics and better processability. This composite can be used to make structures that do not require significant mechanical strength, such as tables, chairs, planks, and solar and wind prototypes, such as ovens and cookers and turbines blades.

Obtenção, caracterização e utilização de um compósito com matriz de resina poliéster e carga de fibras de sisal

The constant search for sustainable alternatives has earned great effort of researchers in research and obtaining new materials, encouraging the rise of eco-friendly productive development and providing simple and practical solutions to economic profitability. In this sense, the use of materials derived from natural renewable sources, vegetables, has great potential applicability to sustainable development. As alternative materials plant fibers can be applied to production of a range of composite materials easing the use of materials derived from non-renewable this thesis were sisal mats used for achieving a composite matrix having as one orthophthalic polyester resin. The webs were subjected to surface treatment in boiling water for 15 minutes. The webs of sisal fibers used were, respectively, 5%, 10% and 15% of the composite weight. The composite was obtained and characterized mechanically and thermally to the chosen formulations. several plates of the composite to obtain the body of evidence for the characterization tests complying with the relevant rules were made. The obtained composites showed strength tensile and bending lower than the array, so it can be used where are required low load requests. The most significant result of the composite studied given to the impact energy absorption, far superior to the matrix used. Other properties were highlighted in oil absorption, and density. It proved the feasibility of obtaining the composite for the three formulations studied C5, C10 and C15 being the most feasible to C10. To demonstrate the feasibility of using composite were made a wall clock, a bench, a chair and a shelf, low mechanical stress structures. It was concluded that the sisal rugs exercised the load function in the composite.

Obtenção, caracterização e utilização de um compósito com matriz de resina poliéster e carga de fibras de sisal

The constant search for sustainable alternatives has earned great effort of researchers in research and obtaining new materials, encouraging the rise of eco-friendly productive development and providing simple and practical solutions to economic profitability. In this sense, the use of materials derived from natural renewable sources, vegetables, has great potential applicability to sustainable development. As alternative materials plant fibers can be applied to production of a range of composite materials easing the use of materials derived from non-renewable this thesis were sisal mats used for achieving a composite matrix having as one orthophthalic polyester resin. The webs were subjected to surface treatment in boiling water for 15 minutes. The webs of sisal fibers used were, respectively, 5%, 10% and 15% of the composite weight. The composite was obtained and characterized mechanically and thermally to the chosen formulations. several plates of the composite to obtain the body of evidence for the characterization tests complying with the relevant rules were made. The obtained composites showed strength tensile and bending lower than the array, so it can be used where are required low load requests. The most significant result of the composite studied given to the impact energy absorption, far superior to the matrix used. Other properties were highlighted in oil absorption, and density. It proved the feasibility of obtaining the composite for the three formulations studied C5, C10 and C15 being the most feasible to C10. To demonstrate the feasibility of using composite were made a wall clock, a bench, a chair and a shelf, low mechanical stress structures. It was concluded that the sisal rugs exercised the load function in the composite.

Obtenção e caracterização de um compósito de matriz polimérica com carga de bucha vegetal luffa cylindrica

Composite materials arise from the need for lighter materials and with bigger mechanical and thermal resistance. The difficulties of discard, recycling or reuse are currently environmental concerns and, therefore, they are study object of much researches. In this perspective the feasibility of using loofahs (Luffa Cylindrica) for obtainment of a polymeric matrix composite was studied. Six formulations, with 4, 5 and 6 treated layers and untreated, were tested. The loofahs were treated in boiling water to remove lignins, waxes and impurities present in the fibers. After that, they were dried in a direct exposure solar dryer. For the characterization of the composite, thermal (thermal conductivity, thermal capacity, thermal diffusivity and thermal resistivity), mechanical (tensile and bending resistance) and physicochemical (SEM, XRD, density, absorption and degradation) properties were determined. The proposed composite has as advantage the low fiber density, which is around 0.66 g/cm³ (almost half of the polyester resin matrix), resulting in an average composite density of around 1.17g/cm³, 6.0 % lower in relation to the matrix. The treatment carried out in the loofahs increased the mechanical strength of the composite and decreased the humidity absorption. The composite showed lower mechanical behavior than the matrix for all the formulations. The composite also demonstrated itself to be feasible for thermal applications, with a value of thermal conductivity of less than 0.159 W/m.K, ranking it as a good thermal insulator. For all formulations/settings a low adherence between fibers and matrix occurred, with the presence of cracks, showing the fragility due to low impregnation of the fiber by the matrix. This composite can be used to manufacture structures that do not require significant mechanical strength, such as solar prototypes, as ovens and stoves.

Obtenção e caracterização de um compósito de matriz polimérica com carga de bucha vegetal luffa cylindrica

Composite materials arise from the need for lighter materials and with bigger mechanical and thermal resistance. The difficulties of discard, recycling or reuse are currently environmental concerns and, therefore, they are study object of much researches. In this perspective the feasibility of using loofahs (Luffa Cylindrica) for obtainment of a polymeric matrix composite was studied. Six formulations, with 4, 5 and 6 treated layers and untreated, were tested. The loofahs were treated in boiling water to remove lignins, waxes and impurities present in the fibers. After that, they were dried in a direct exposure solar dryer. For the characterization of the composite, thermal (thermal conductivity, thermal capacity, thermal diffusivity and thermal resistivity), mechanical (tensile and bending resistance) and physicochemical (SEM, XRD, density, absorption and degradation) properties were determined. The proposed composite has as advantage the low fiber density, which is around 0.66 g/cm³ (almost half of the polyester resin matrix), resulting in an average composite density of around 1.17g/cm³, 6.0 % lower in relation to the matrix. The treatment carried out in the loofahs increased the mechanical strength of the composite and decreased the humidity absorption. The composite showed lower mechanical behavior than the matrix for all the formulations. The composite also demonstrated itself to be feasible for thermal applications, with a value of thermal conductivity of less than 0.159 W/m.K, ranking it as a good thermal insulator. For all formulations/settings a low adherence between fibers and matrix occurred, with the presence of cracks, showing the fragility due to low impregnation of the fiber by the matrix. This composite can be used to manufacture structures that do not require significant mechanical strength, such as solar prototypes, as ovens and stoves.

Caracterização de um compósito utilizando cimento com agregado de resíduo plástico e resíduo de gesso

The demand for environmental comfort in construction systems within the insulation and thermal comfort, plus the advent of new laws regulating the minimum requirements of comfort, disposal of solid industrial waste, construction waste, the requirements of consumers by adopting construction methods "cleaner", encouraged the development of this work. Aims technologically characterize the composite proposed in three types of samples (10%, 30% and 50% of thermoset plastic industrial waste) and raw materials: gypsum waste, cement and plastic thermosetting industrial waste in order to produce the composite with properties of thermal insulation: conductivity, thermal diffusivity, specific heat and resistivity. The physical, structural and morphological properties of the raw materials were investigated by thermogravimetry analysis (TG / DSC), X-ray diffraction (DRX), X-ray fluorescence (FXR) and scanning electron microscopy (MEV). Obtaining mechanical properties through the compression strength test. The analysis results indicate characteristics suitable for cement matrix composite production with the addition of thermosetting plastic industrial waste and gypsum waste, with potential application of these materials in composites with properties of thermal insulation. Finally, assessing what proportion showed up with better performance. Considering the analysis and testing carried out.

Caracterização de um compósito utilizando cimento com agregado de resíduo plástico e resíduo de gesso

The demand for environmental comfort in construction systems within the insulation and thermal comfort, plus the advent of new laws regulating the minimum requirements of comfort, disposal of solid industrial waste, construction waste, the requirements of consumers by adopting construction methods "cleaner", encouraged the development of this work. Aims technologically characterize the composite proposed in three types of samples (10%, 30% and 50% of thermoset plastic industrial waste) and raw materials: gypsum waste, cement and plastic thermosetting industrial waste in order to produce the composite with properties of thermal insulation: conductivity, thermal diffusivity, specific heat and resistivity. The physical, structural and morphological properties of the raw materials were investigated by thermogravimetry analysis (TG / DSC), X-ray diffraction (DRX), X-ray fluorescence (FXR) and scanning electron microscopy (MEV). Obtaining mechanical properties through the compression strength test. The analysis results indicate characteristics suitable for cement matrix composite production with the addition of thermosetting plastic industrial waste and gypsum waste, with potential application of these materials in composites with properties of thermal insulation. Finally, assessing what proportion showed up with better performance. Considering the analysis and testing carried out.

Reforço de pilares por confinamento com mantas de fibras de carbono: avaliação de modelos de comportamento

A presente dissertação incide sobre o estudo dos efeitos do confinamento com materiais compósitos de polímeros reforçados com fibras de carbono (CFRP) em pilares de estruturas de betão armado. A motivação para este estudo surge da necessidade de aprofundar conhecimentos acerca do comportamento dos pilares de betão reforçados por confinamento com CFRP, uma vez que a sua aplicação apresenta uma crescente importância, por exemplo, para aumento da resistência e da ductilidade de estruturas de betão armado. Fez-se, inicialmente, uma breve revisão das técnicas de reforço convencionais utilizadas em pilares de betão armado, com ênfase no reforço exterior com polímeros reforçados com fibras. A elevada resistência à tração, à corrosão e à fadiga, o baixo peso volúmico, a versatilidade e a diversidade dos sistemas comercializados com CFRP tornam este material muito competitivo para este tipo de aplicação. Na sequência desse estudo, realizou-se uma revisão bibliográfica acerca dos modelos de comportamento que permitem prever o desempenho de pilares de betão confinados com CFRP, sujeitos a esforços de compressão. Como forma de análise desses modelos, desenvolveu-se uma ferramenta numérica em ambiente Mathworks - Matlab R2015a, que permitiu a obtenção e posterior comparação dos diagramas de tensão-extensão descritos pelos modelos desenvolvidos por Manfredi e Realfonzo (2001), Ferreira (2007) e Wei e Wu (2011). Por fim, comparam-se os resultados experimentais de Paula (2003) e de Rocca (2007) com os dos modelos constitutivos referidos anteriormente, analisando-se também a influência de vários fatores na eficácia do confinamento, tais como o boleamento, o número de camadas de CFRP e a geometria da secção transversal. Foram ainda comparados e discutidos resultados relativos ao confinamento parcial de pilares. Os resultados obtidos indicam que os modelos analíticos representam relativamente bem o andamento das curvas do betão confinado para secções circulares, quadradas e retangulares, verificando-se as principais discrepâncias nestas duas últimas tipologias de secção transversal, dada a dificuldade associada à quantificação de parâmetros associados ao seu comportamento (por exemplo, boleamento de arestas). No entanto, verificou-se igualmente que com um adequado boleamento de arestas (e consequente aumento da relação entre o raio de canto e a largura da secção de betão), bem como com um aumento do número de camadas de material compósito, é possível aumentar a tensão resistente e a extensão axial na rotura do betão à compressão.

Granitos Variscos do Centro Norte de Portugal

A Cadeia Varisca Europeia, formada no final do Paleozóico, estende-se desde a Europa de Leste até à Península Ibérica e inclui extensas áreas ocupadas por rochas graníticas, representando, por isso, uma das regiões do globo em que mais se têm investigado os processos de reciclagem e acreção crustal em contexto de colisão continental. O Maciço Ibérico constitui o segmento mais ocidental do orógeno varisco europeu e uma das áreas onde a actividade plutónica está mais bem expressa e mostra uma maior diversidade tipológica. No Maciço Ibérico, em particular na Zona Centro Ibérica (ZCI), a intrusão de rochas granitóides de idade varisca está preferencialmente associada com a terceira fase de deformação (D3). De acordo com as suas relações com este evento de deformação, os granitóides da ZCI foram subdivididos em dois grandes grupos: sin-D3 e tardi-pós-D3. Em termos petrográficos e geoquímicos, os maciços graníticos sin- e tardi-pós-D3 têm sido integrados em duas séries principais: (a) a série dos granitos de duas micas e dos leucogranitos fortemente peraluminosos e (b) a série dos monzogranitos e granodioritos, metaluminosos a fracamente peraluminosos, com biotite ± anfíbola. Os granitos da primeira série apresentam uma filiação de tipo S e resultam da anatexia de materiais supracrustais durante o clímax de metamorfismo regional, enquanto.os granitóides da segunda série exibem características transicionais I-S e têm sido interpretados, quer como produtos da hibridização de magmas félsicos crustais com magmas básicos de proveniência mantélica, quer como resultantes da anatexia de protólitos metaígneos da crosta inferior. O trabalho realizado no batólito das Beiras revela que o clímax de metamorfismo regional foi atingido neste sector durante um evento extensional (D2), que foi acompanhado por intensa migmatização. No ínício da D3, o volume de fundidos crustais já seria suficientemente grande (ca. 15-35%) para que pudesse ocorrer a sua separação do resíduo sólido. Assim, durante a tectónica transcorrente D3, dá-se a ascenção, diferenciação e consolidação de abundantes quantidades de magmas graníticos, fortemente peraluminosos e isotopicamente evoluídos (tipo-S), que vêm a originar enormes batólitos de leucogranitos de duas micas, com idades entre 317-312 Ma. No final da D3, com a progressiva substituição do manto litosférico pela astenosfera, mais quente, diminui a densidade da coluna litosférica e ocorre o levantamento isostático e exumação da crusta. A fusão por descompressão da astenosfera gera líquidos básicos que hibridizam com os fundidos félsicos crustais, em proporções variáveis, e produzem magmas metaluminosos a ligeiramente peraluminosos, de afinidade calco-alcalina. A ascenção destes magmas terá tido lugar nos últimos estádios da deformação transcorrente e a sua instalação no nível crustal final ocorre após a D3, dando origem aos inúmeros maciços compósitos de granitóides biotíticos híbridos tardi-pós-cinemáticos, presentes no batólito das Beiras. Os dados de campo mostram que estes granitóides são intrusivos nos plutões sin-D3, cortam as estruturas regionais e provocam metamorfismo de contacto nas sequências do Carbónico Superior. Com base nas idades U-Pb obtidas em zircões e monazites, é possível datar este importante período de plutonismo granítico com 306-294 Ma. A assinatura geoquímica e isotópica dos granitóides híbridos tardi-pós-D3 revela que, para além da mistura de componentes com proveniência distinta (manto empobrecido e crusta continental), a sua evolução foi, em grande parte, controlada por processos de cristalização fraccionada (modelo AFC).

Membranas compósitas para separação de CO2

O presente trabalho envolveu a produção de membranas compósitas para separação de CO2 a altas temperaturas. Os compósitos habituais são constituídos por duas fases, uma cerâmica, de céria dopada com gadolínio (Ce0.9Gd0.1O0.95 - CGO) condutora de iões óxido, que funciona como suporte da segunda fase composta por uma mistura eutética de carbonatos alcalinos (Li2CO3 e Na2CO3), que assegura o transporte de iões carbonato. O objetivo do trabalho prende-se com o estudo do transporte de iões através destes compósitos, por forma a perceber se os sais destes compósitos apresentam condução iónica singular ou condução mista. Neste sentido a resposta a esta questão teve por base a realização de ensaios de eficiência faradaica com recurso a amostras compósitas envolvendo matrizes de CGO (condutor de iões óxido) e de aluminato de lítio (não condutor de iões óxido). A preparação tanto de esqueletos porosos como de compósitos foi realizada tendo por base métodos e precursores semelhantes aos usados na literatura. Primeiramente efetuou-se o processamento dos esqueletos porosos para posteriormente impregnação com mistura eutética de carbonatos. Obtidos os compósitos estes foram caraterizados por microscopia de impedância e por microscopia eletrónica de varrimento de forma a serem submetidos mais tarde aos ensaios de eficiência faradaica. Os resultados de eficiência faradaica revelaram que na realidade existem processos de condução mista cuja importância depende das condições de operação da membrana.