Building surfaces and their effect on the urban thermal environment

Use of high reflectance surfaces reduces the amount of solar radiation absorbed through building envelopes and urban structures and thus keeping their surfaces cooler. The cooling energy savings by using high reflectance surfaces have been well documented. Higher surface temperatures add to increasing the ambient temperature as convection intensity is higher. Such temperature increase has significant impacts on the air conditioning energy utilization in hot climates. This study makes use of numerical simulations to analyze the effect of commonly used building materials on the air temperature. A part of the existing CBD (Central Business District) area of Singapore was selected for the study. A series of Computational Fluid Dynamics (CFD) simulations have been carried out using the software CFX-5.6. It was found that at low wind speeds, the effect of materials on the air temperature was significant and the temperature at the middle of a narrow canyon increased up to 2.5[degrees]C with the facade material having lower reflectance.

Convection suppression in an attic shaped enclosure

In recent times there has been growing interest in the integration of solar collectors, for water heating, into the façade of buildings. However, the design methodology of these devices remains largely the same as typical “stand-alone” collectors. As such it is still common for materials with a high thermal resistance to be used for insulating the rear surface of these collectors.

Unlike a “stand-alone” solar collector that is exposed to the atmosphere at all faces; a building integrated system allows the opportunity for air to act as an insulator at the rear surface of the solar collector. The use of convection suppression devices has been widely discussed in the literature as a means of reducing natural convection heat loss from the front surface of glazed solar collectors. However in this study the use of baffles in an attic was examined as a means of suppressing heat loss by natural convection from the rear surface of a roof-integrated solar collector. The aim of the study was to examine whether the use of baffles would allow the cost of building integrated collectors to be reduced by removing the cost of insulating material.

To determine the effect of baffles in the attic space at the rear surface of the collector, a 3-dimensional triangular cross sectioned enclosure with a vertical aspect ratio of 0.5 and a horizontal aspect ratio of 3.3 was modelled. The flow patterns and heat transfer in the enclosure were determined for Grashof Numbers in the range of 106 to 107 using a commercially available finite volume CFD solver.
It was found that the use of a single adiabatic baffle mounted vertically downwards from the apex, and extending the length of the enclosure, would alter the flow such that the heat transfer due to natural convection was reduced with respect to the length of the baffle.

Furthermore, it was observed that a series of convection cells, not previously reported in the literature, appeared to exist along the length of the enclosure. As such, it may be possible to derive additional benefit in reducing the heat transfer by adding lateral baffles in addition to the single longitudinal baffle modelled in this study.

Characterization of high fluid strain micro contractions to study the stress on biological fluids

Microfluidics has the potential to enhance the understanding of the biological fluids under strain, due to the laminar nature of the fluid and the possibility to mimic the real conditions. We present advances on charaterization of a microfluidic platform to study high strain rate flows in the transport of biological fluids. These advances are improvements on the reproduction of a  constant extensional strain rate using micro contractions and development of 3D numerical models. The micro geometries have been fabricated in polydimethyl siloxame (PDMS) using standard soft-lithography techniques with a photolithographically patterned mold. A comparison of some microcontractions with different funnel characteristics is presented. The Micro Particle Image Velocimetry technique has been applied to validate the numerical simulations. We demonstrate the use of microfluidics in the reproduction of a large range of controllable extensional strains that can be used in the study of the effect of flow on biological fluids.

Hydrodynamic flow focusing to study the isolated effects of the flow components

Biological fluids such as blood, proteins and DNA solutiosn moving within fluidic channels can potentially be exposed to high level of shear, extension or mixed stress, either in vitro such as industrial processing of blood products or in vivo such as ocurrs in some pathological conditions. This exposure to a high level of strain can trigger some reactions. In most of the cases the nature of the flow is mixed with shear and extensional components. The ability ot isolate the effects of each component is critical in order to understand the mechanisms behind the reactions and potentially prevent them. Applying hydrodynamic flow focusing, we present in this investigation the characterization of microchannels that allow study of the regions of high shear or high extension strain rate. Micro channels were fabricated in polydimethyl siloxane (PDMS)  using standard soft-lithography techniques with a photolithographically patterned mold. Characterization of the regions with high shear and high extension strain rate is presented. Computational Fluid Dynamics (CFD) simulations in three dimensions have been carried out to gain more detailed local flow information, and the results have been validated experimentally. A comparison between the numerical models and experiment and is presented. The advantages of microfluidic flow focusing in the study  of the effects of shear and extension strain rates for biological fluids are outlined.

Mixing characterisation for a serpentine microchannel equipped with embedded barriers

This paper describes the design, simulation, fabrication and experimental analysis of a passive micromixer for the mixing of biological solvents. The mixer consists of a T-junction, followed by a serpentine microchannel. the serpentine has three arcs, each equipped with circular barriers that are patterned as two opposing triangles. >The barriers are engineered to induce periodic perturbations in the flow field and enhance the mixing. CFD (Computational Fluid Dynamics) method is applied to optimise the geometric variables of the mixer before fabrication. The mixer is made from PDMS (Polydimethylsiloxane) using photo- and soft-lithography techniques. Experimental measurements are performed using yellow and blue food dyes as the mixing fluids. The mixing is measured by analysing the composition of the flow's colour across the outlet channel. The performance of the mixer is examined in a wide range of flow rates from 0.5 to 10 µl/min. Mixing efficiencies of higher than 99.4% are obtained in the experiments confirming the results of numerical simulations. The proposed mixer can be employed as a part of lab-on-a-chip for biomedical applications.

3D hydrodynamic analysis of a biomimetic robot fish

This paper presents a three-dimensional (3D) computational fluid dynamic simulation of a biomimetic robot fish. Fluent and user-defined function (UDF) is used to define the movement of the robot fish and the Dynamic Mesh is used to mimic the fish swimming in water. Hydrodynamic analysis is done in this paper too. The aim of this study is to get comparative data about hydrodynamic properties of those guidelines to improve the design, remote control and flexibility of the underwater robot fish.

Integrated fluid-thermal-structural numerical analysis for the quenching of metallic components

The quenching of a metal component with a channel section in a water tank is numerically simulated. Computational fluid dynamics (CFD) is used to model the multiphase flow and the heat transfer in film boiling, nucleate boiling and convective cooling processes to calculate the difference in heat transfer rate around the component and then combining with the thermal simulation and structure analysis of the component to study the effect of heat transfer rate on the distortion of the U-channel component. A model is also established to calculate the residual stress produced by quenching. The coupling fluid-thermal-structural simulation provides an insight into the deformation of the component and can be used to perform parameter analysis to reduce the distortion of the component. © 2011 Shanghai Jiaotong University and Springer-Verlag Berlin Heidelberg.

Thermal and ventilation performance of a multifunctional sports hall within an aquatic centre

There has been an increasing demand for sports facilities in urban areas recently. As a result of this, more attention is drawn towards not only the energy performance of these building typologies, but also creating a healthy indoor environment for the users. This Study investigates the thermal and ventilation performance of a sports hall within an aquatic centre using computational fluid dynamics (CFD) simulations. IES Virtual Environment software was used to perform the simulations. A number of scenarios were tested by changing the position of extract fans as well as by incorporating natural ventilation strategies. A high level of discomfort was observed in the space. Better comfort condition was achieved by changing the location of exhaust fans ad openings. The results help to recommend some guidelines to inform the proposed refurbishment plans of the site.

Thermal analysis of nanofluids in microfluidics using an infrared camera

We present the thermal analysis of liquid containing Al2O3 nanoparticles in a microfluidic platform using an infrared camera. The small dimensions of the microchannel along with the low flow rates (less than 120 μl min−1) provide very low Reynolds numbers of less than 17.5, reflecting practical parameters for a microfluidic cooling platform. The heat analysis of nanofluids has never been investigated in such a regime, due to the deficiencies of conventional thermal measurement systems. The infrared camera allows non-contact, three dimensional and high resolution capability for temperature profiling. The system was studied at different w/w concentrations of thermally conductive Al2O3 nanoparticles and the experiments were in excellent agreement with the computational fluid dynamics (CFD) simulations.

3D locomotion biomimetic robot fish with haptic feedback

This thesis developed a biomimetic robot fish and built a novel haptic robot fish system based on the kinematic modelling and three-dimentional computational fluid dynamic (CFD) hydrodynamic analysis. The most important contribution is the successful CFD simulation of the robot fish, supporting users in understanding the hydrodynamic properties around it.

Computational simulation of the influence of inert particles on incomplete combustion of methane at a low air factor

It is well known that the gas–solid system plays a significant role in many industrial processes. It is a complex physical and chemical process, generally consisting of heat transfer, mass transfer, species diffusion, and chemical reactions. In this paper, the reaction of methane with air at a low air factor and the gas flow in a fluidized bed with 0.1 mm solid particles are computationally simulated to enable the study of the effect of the inert particles on the species diffusion and the chemical reactions. The reaction of methane and air is modeled by a two-step reaction mechanism that produces a continuous fluid phase composed of six gases (CH₄, CO, O₂, CO₂, H₂O, and N₂) and discrete solid particles in the reactor. The simulation results are compared with experiment and show that the finite rate model and the eddy dissipation model can well describe the reactions of gases in high-density gas–solid systems. The distribution of each gas and the particle behaviors are analyzed for incomplete combustion at different concentrations of loaded solid particles. The inert particles change the reactions by enhancing both the chemical kinetics and the species diffusion dynamics.

Drag models comparison by single injection in vacuum fluidised beds

Single bubble injection simulations inside a minimally fluidized bed have been studied widely and are often used to validate the accuracy of different numerical models. Bubble shape, size and voidage distribution are the important parameters that are validated from the experiments. In the present work, the most widely used drag model (Gidaspow’s drag model) is compared to a new proposed slip flow drag model which takes into account the presence of the slip flow regime, often encountered in vacuum fluidized beds and characterised by Knudsen no. (Kn). Shape and size prediction of the bubble evolution inside the bed is carried out numerically by using the two fluid model, comparing the results predicted by the drag models. It is seen that the predictions are different for the two drag models only under high vacuum conditions corresponding to Kn in slip/transition flow regime. The predictions are also found sensitive to pressure gradient in the bed and fluid velocity.