903 resultados para CONVERSION COATINGS
Resumo:
The tribological response of multilayer micro/nanocrystalline diamond coatings grown by the hot filament CVD technique is investigated. These multigrade systems were tailored to comprise a starting microcrystalline diamond (MCD) layer with high adhesion to a silicon nitride (Si3N4) ceramic substrate, and a top nanocrystalline diamond (NCD) layer with reduced surface roughness. Tribological tests were carried out with a reciprocating sliding configuration without lubrication. Such composite coatings exhibit a superior critical load before delamination (130–200 N), when compared to the mono- (60–100 N) and bilayer coatings (110 N), considering ∼10 µm thick films. Regarding the friction behaviour, a short-lived initial high friction coefficient was followed by low friction regimes (friction coefficients between 0.02 and 0.09) as a result of the polished surfaces tailored by the tribological solicitation. Very mild to mild wear regimes (wear coefficient values between 4.1×10−8 and 7.7×10−7 mm3 N−1 m−1) governed the wear performance of the self-mated multilayer coatings when subjected to high-load short-term tests (60–200 N; 2 h; 86 m) and medium-load endurance tests (60 N; 16 h; 691 m).
Resumo:
Ball rotating micro-abrasion tribometers are commonly used to carry out wear tests on thin hard coatings. In these tests, different kinds of abrasives were used, as alumina (Al2O3), silicon carbide (SiC) or diamond. In each kind of abrasive, several particle sizes can be used. Some studies were developed in order to evaluate the influence of the abrasive particle shape in the micro-abrasion process. Nevertheless, the particle size was not well correlated with the material removed amount and wear mechanisms. In this work, slurry of SiC abrasive in distilled water was used, with three different particles size. Initial surface topography was accessed by atomic force microscopy (AFM). Coating hardness measurements were performed with a micro-hardness tester. In order to evaluate the wear behaviour, a TiAlSiN thin hard film was used. The micro-abrasion tests were carried out with some different durations. The abrasive effect of the SiC particles was observed by scanning electron microscopy (SEM) both in the films (hard material) as in the substrate (soft material), after coating perforation. Wear grooves and removed material rate were compared and discussed.
Resumo:
The injection process of glass fibres reinforced plastics promotes the moulds surface degradation by erosion. In order to improve its wear resistance, several kinds of PVD thin hard coatings were used. It is well-known that nanostructures present a better compromise between hardness and toughness. Indeed, when the coating is constituted by a large number of ultra-thin different layers, cracks and interface troubles tend to decrease. However, it is not clear that these nanostructures present a better wear behaviour in erosion processes. In order to study its wear behaviour, a sputtered PVD nanostructured TiAlCrSiN coating was used. The substrate and film surfaces topography were analyzed by profilometry and atomic force microscopy techniques. Film adhesion to the substrate was evaluated by scratch tests. The surface hardness was measured with a Vickers micro-hardness tester. The wear resistance was evaluated by micro-abrasion with a rotating ball tribometer tests. Slurry of SiC particles in distilled water was used in order to provoke the surface abrasion. Different duration tests were performed in order to analyze the wear evolution. After these tests, the wear mechanisms developed were analyzed by scanning electron microscopy. Wear craters were measured and the wear rate was calculated and discussed. With the same purpose, coated inserts were mounted in an injection mould working with a 30% glass fibres reinforced polypropylene. After 45 000 cycles no relevant wear was registered.
Resumo:
Dissertação para a obtenção de grau de doutor em Ciências da Engenharia e Tecnologia
Resumo:
Due to external constraints (opposed by the market and legal system) and internal changes nonprofit organizations have been converting to for-profit entities combining commercial revenue and social value creation. To create an understanding of the conversion process considering its challenges, the reasons, the decision-making process and key success factors of a conversion are examined. Therefore, a two-step research procedure is used combining literature research and a multiple case study approach based on expert interviews with known companies. The outcome is a helpful guideline (including a decision matrix) for social entrepreneurs that might face a conversion.
Resumo:
The importance of the regional level in research has risen in the last few decades and a vast literature in the fields of, for instance, evolutionary and institutional economics, network theories, innovations and learning systems, as well as sociology, has focused on regional level questions. Recently the policy makers and regional actors have also began to pay increasing attention to the knowledge economy and its needs, in general, and the connectivity and support structures of regional clusters in particular. Nowadays knowledge is generally considered as the most important source of competitive advantage, but even the most specialised forms of knowledge are becoming a short-lived resource for example due to the accelerating pace of technological change. This emphasizes the need of foresight activities in national, regional and organizational levels and the integration of foresight and innovation activities. In regional setting this development sets great challenges especially in those regions having no university and thus usually very limited resources for research activities. Also the research problem of this dissertation is related to the need to better incorporate the information produced by foresight process to facilitate and to be used in regional practice-based innovation processes. This dissertation is a constructive case study the case being Lahti region and a network facilitating innovation policy adopted in that region. Dissertation consists of a summary and five articles and during the research process a construct or a conceptual model for solving this real life problem has been developed. It is also being implemented as part of the network facilitating innovation policy in the Lahti region.
Resumo:
Collection : Encyclopédie théologique ; 28-30
Resumo:
Collection : Encyclopédie théologique ; 28-30
Resumo:
Collection : Encyclopédie théologique ; 28-30
Resumo:
Collection : Encyclopédie théologique ; 28-30
Resumo:
Collection : Encyclopédie théologique ; 28-30
