Three-port beam splitter of a binary fused-silica grating

A deep-etched polarization-independent binary fused-silica phase grating as a three-port beam splitter is designed and manufactured. The grating profile is optimized by use of the rigorous coupled-wave analysis around the 785 nm wavelength. The physical explanation of the grating is illustrated by the modal method. Simple analytical expressions of the diffraction efficiencies and modal guidelines for the three-port beam splitter grating design are given. Holographic recording technology and inductively coupled plasma etching are used to manufacture the fused-silica grating. Experimental results are in good agreement with the theoretical values. (c) 2008 Optical Society of America.

Stabilization of optical Fabry-Perot sensor by active feedback control of diode laser

This paper presents the design and characterization of a fiber Fabry-Perot interferometer (FFPI) acoustic wave detector with its Q point being stabilized actively. The relationship between the reflectivity of the F-P cavity facets and cavity length was theoretically analyzed, and high visibility of 100% was realized by optimized design of the F-P cavity. To prevent the drifting of the Q point, a new stabilization method by actively feedback controlling of the diode laser is proposed and demonstrated, indicating the method is simple and easy operating. Measurement shows that good tracing of Q point was effectively realized. (c) 2008 Elsevier B.V. All rights reserved.

Inverse symmetric Dammann gratings

Inverse symmetric Dammann grating is a special grating, whose transition points are reflection symmetric about the midpoint with inverse phase offset in one period. It can produce even-numbered or odd-numbered array illumination when the phase modulations are pi or a specific value. Numerical solutions optimized by the steepest-descent algorithm for binary phase and multilevel phases with splitting ratio from I x 4 to 1 x 14 are given. Fabrication of 1 x 6 array without the zero-order intensity and 1 x 7 array with the zero-order intensity are made from the same amplitude mask. A 6 x 6 output without the crossed zero-orders was achieved by crossing two one-dimensional 1 x 6 inverse symmetric Dammann gratings. This grating may have potential value for practical applications. (C) 2008 Elsevier B.V. All rights reserved.

Coma measurement by use of an alternating phase-shifting mask mark with a specific phase width

The correlation between the coma sensitivity of the alternating phase-shifting mask (Alt-PSM) mark and the mark's structure is studied based on the Hopkins theory of partially coherent imaging and positive resist optical lithography (PROLITH) simulation. It is found that an optimized Alt-PSM mark with its phase width being two-thirds its pitch has a higher sensitivity to coma than Alt-PSM marks with the same pitch and the different phase widths. The pitch of the Alt-PSM mark is also optimized by PROLITH simulation, and the structure of p - 1.92 lambda/NA and pw = 2p/3 proves to be with the highest sensitivity. The optimized Alt-PSM mark is used as a measurement mark to retrieve coma aberration from the projection optics in lithographic tools. In comparison with an ordinary Alt-PSM mark with its phase width being a half its pitch, the measurement accuracies of Z(7) and Z(14) apparently increase. (C) 2009 Optical Society of America

Transformação de metanol em olefinas leves catalisada por zeólitas HZSM-5

A reação de transformação de MeOH em olefinas leves foi investigada sobre zeólitas HZSM-5 com razões SiO2/Al2O3 (SAR) iguais a 30, 80 e 280. As propriedades ácidas e texturais da amostra com SAR 30 foram modificadas por impregnação com ácido fosfórico. A caracterização físico-química das amostras foi realizada empregando-se as técnicas de FRX, fisissorção de N2, DRX, DTP de NH3 e IV com adsorção de piridina. O desempenho catalítico das mesmas foi comparado tanto em condições reacionais similares (mesma T, pressão parcial de MeOH e WHSV) como em condições de isoconversão. Verificou-se, que quanto maior a SAR da zeólita, menor a densidade total e a força dos sítios ácidos presentes, sendo este efeito mais significativo para os sítios de Brönsted. O efeito do aumento da SAR favoreceu a estabilidade catalítica e a formação de olefinas leves, principalmente propeno. No caso das amostras contendo fósforo, foi observada uma redução linear na área específica BET e no volume de microporos com o aumento do teor de fósforo. Estes resultados, aliados aos obtidos por DRX, sugerem que a redução mais significativa na área específica e no volume de microporos pode ser associada à redução na cristalinidade e à formação de espécies amorfas contendo fósforo, que bloqueariam a estrutura porosa da zeólita. Não se observou alteração significativa na força dos sítios fracos, enquanto a força dos sítios fortes diminuiu significativamente. As amostras apresentando menor SAR e menor teor de fósforo foram mais ativas. Por outro lado, em condições de isoconversão de 916%, a amostra mais seletiva à formação de olefinas foi aquela com maior SAR. Dentre as amostras impregnadas, aquela contendo 4% de fósforo foi a mais seletiva a propeno, enquanto a que continha 6% foi mais seletiva a eteno. A amostra com SAR igual a 280 foi investigada variando-se a temperatura de reação (400, 500 e 540C) e a pressão parcial de metanol (0,038; 0,083 e 0,123 atm), através de um planejamento experimental do tipo Box-Benhnken (32). O rendimento otimizado em olefinas leves foi alcançado a 480C e 0,08 atm. O modelo proposto descreveu bem os dados experimentais e evidenciou a existência de uma faixa ótima de temperatura para maximização do rendimento em propeno e eteno, o qual foi também afetado pela pressão parcial de MeOH na faixa estudada. Palavras-chave: ZSM-5, olefinas, propeno, eteno, processo MTO, fósforo.

Laser beam automatic alignment in multipass amplifier

A laser beam automatic alignment system is applied in a multipass amplifier of the SG-III prototype laser. Considering the requirements of the SG-III prototype facility, by combining the general techniques of the laser beam automatic alignment system, according to the image relayed of the pinholes in the spatial filter, and utilizing the optical position and the spatial distribution of the four pinholes of the main spatial filter in the multipass amplifier of the SG-III prototype, a reasonable and optimized scheme for automatic aligning multipass beam paths is presented. It is demonstrated on the multipass amplifier experimental system. (C) 2004 Society of Photo-Optical Instrumentation Engineers.

高功率钕玻璃激光三倍频脉冲时间波形的研究

基于目前国内规模最大的激光驱动器——“神光Ⅱ”八路基频光已经实现功率平衡运行，通过改变其中若干路三倍频系统各调谐量的偏离，对输出三倍频波形进行束与束之间的横向对比研究．研究发现，对于Ⅱ类-Ⅱ类偏振失配三倍频系统，在影响转换效率的三个调谐量中，偏振分配角失配△θp，对三倍频波形影响最大；在入射基频功率密度约为1．0GW／cm^2情况下，当三倍频系统三个调谐量都处在最佳匹配时，三倍频波形半峰全宽τ最小。研究工作为最终实现“神光Ⅱ”八路光束三倍频功率平衡输出提供了晶体调试的方法。

"神光-Ⅱ"装置第九路靶场终端光学组件的研制

针对“神光-Ⅱ”装置第九路系统主激光瞄准精度小于等于30μm和大焦斑辐照均匀性优于10％的要求，提出了靶场终端光学组件的设计结构。应用有限元法对组件关键机械元件和ICF靶室整体进行动静态分析，优化了设计参数。同时与聚焦透镜配合进行数值分析列阵透镜，确定了单元数、曲率和厚度以及单元长和宽等参数。经过实验测试，主激光瞄准精度达到28．9μm，大焦斑辐照的形状为1000μm×500μm，均匀性为12．0％。

大口径八边形钕玻璃片支撑系统的光机集成分析

控制由机械装夹方式所引入的波前畸变以提高惯性约束聚变(ICF)输出光束的质量，是在大口径钕玻璃片主放大器结构设计中必须考虑的。提出了一种新的有限元变形结果与光学元件面形畸变之间的数据处理方式，并与传统方式进行了对比。基于新的数据处理接口，利用光机集成分析方法对大口径八边形钕玻璃片的支撑系统结构设计参数进行优化。优化的结果保证了由支撑系统引起的透过波前畸变小于十分之一波长，同时波前畸变与设计参数变动的相关性最小。

神光Ⅱ升级装置终端光学组件的排布设计

设计高功率激光装置靶场终端光学组件(FOA)时考虑的重要因素是鬼像对光学元件的破坏。由于神光Ⅱ升级装置(SG-Ⅱ-U)的输出能量高、靶场空间小、鬼像分布情况复杂,导致了终端光学组件的设计难度很高。用自主研发的鬼像控制设计软件对神光Ⅱ升级装置靶场终端光学组件排布进行设计,给出了进行鬼像控制设计时需考虑的设计因素,并对比研究了两种靶场终端光学组件设计方案的优缺点,最后结合神光Ⅱ升级装置的特点,优化设计出神光Ⅱ升级装置靶场终端光学组件的最终排布方案。

Optimization of Pulse Temporal Contrast in Optical Parametric Chirped Pulse Amplification

In optical parametric chirped pulse amplification (OPCPA), the degradation of temporal contrast of the compressed signal pulse mainly results from spectral clipping in the grating stretcher with finite size of the optics, parametric fluorescence (PF) and the spectral variations transferred from temporal fluctuation of the pump pulse. The temporal contrast of the recompressed amplified pulse in the OPCPA system is studied numerically and a number of solutions are considered and optimized to achieve the highest temporal contrast.

Phase-shifting apodizers for increasing focal depth

We propose the use of a phase-shifting apodizers to increase focal depth, and we study the axial and radial behavior of this kind of apodizer under the condition that the axial intensity distribution is optimized for high focal depth. (C) 2002 Optical Society of America.

Phase-shifting apodizer for next-generation digital versatile disk

The next generation digital versatile disk (DVD) using blue lasers will have a capacity of 13 to 15 Gbytes. Compared with current DVD, the wavelength will be shorter and the numerical aperture (NA) will be higher. But with the increase of NA and decrease of wave length, the depth of focus (DOF) decrease rapidly, which makes it hard for the servo-system to track. We propose an optimized three-portion phase-shifting apodizer to increase the depth of focus and at the same time minimize the spot size, which makes the DOF of next generation DVD comparable to current DVD. The simulation result shows that an optical system with this apodizer also has a good defocus characteristic. (C) 2001 Society of Photo-Optical Instrumentation Engineers.

Thiophene-fluorene derivatives with high three-photon absorption activities and their application to optical power limiting

The three-photon absorption (3PA) properties of two thiophene-fluorene derivatives (abbreviated as MOTFTBr and ATFTBr) have been determined by using a Q-switched Nd:YAG laser pumped wish 38ps pulses at 1064nm in DMF. The measured 3PA cross-sections are 152x10(-78)cm(6)s(2) and 139x10(-78)cm(6)s(2), respectively. The optimized structures were obtained by AM1 calculations and the results indicate that these two molecules show nonplanar structures, and attaching different donors has different effects on the molecular structure. The charge density distributions during the excitation were also systematically studied by using AM1 method. In addition, an obvious optical power limiting effect induced by 3PA has been demonstrated for both derivatives.

Analysis on a new type magneto-optical disk for blue lasers

The conventional TbFeCo magneto-optical (MO) medium has a relatively smaller Kerr rotation angle in the blue region than in the red. With the recording wavelength gradually moving to the short wavelength, if TbFeCo is still used as recording medium, the conventional MO disk structure must be optimized to get a larger carrier to noise ratio (CNR). Sabi et al. have found that adding a metal layer attached to the TbFeCo film as thermal control layer is a useful way to get a high CNR. In this paper, we proved this through calculation, and carried out optimization of the new type of disk. Calculation results showed that the new structure is useful in preventing an excessive temperature increase, and has a better thermal response. (c) 2005 Elsevier B.V. All rights reserved.