Precipitation, microstructure and mechanical properties of low nickel maraging steel

A maraging steel with a composition of Fe–12·94Ni–1·61Al–1·01Mo–0·23Nb (wt-%) was investigated. Optical, scanning electron and transmission electron microscopy and X-ray diffraction analysis were employed to study the microstructure of the steel after different aging periods at temperatures of 450–600°C. Hardness and Charpy impact toughness of the steel were measured. The study of microstructure and mechanical properties showed that nanosized precipitates were formed homogeneously during the aging process, which resulted in high hardness. As the aging time is prolonged, precipitates grow and hardness increases. Fractography of the as forged steel has shown mixed ductile and brittle fracture and has indicated that the steel has good toughness. Relationships among heat treatment, microstructure and mechanical properties are discussed. Further experiments using tensile testing and impact testing for aged steel were carried out.

Structural and magnetic properties of sol-gel Co2xNi0.5-xZn0.5-xFe2O4 thin films

Nanocrystalline Co2xNi0.5-xZn0.5-xFe2O4 (x = 0-0.5) thin films have been synthesized with various grain sizes by a sol-gel method on polycrystalline silicon substrates. The morphology as well as magnetic and microwave absorption properties of the films calcined at 1073 K were studied using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and vibrating sample magnetometry. All films were uniform with out microcracks . The Co content in the Co-Ni-Zn films resulted in a grain size ranging from 15 to 32 nm while it ranged from 33 to 49 nm in the corresponding powders. Saturation and remnant magnetization increased with increase in grain size, while coercivity demonstrated a drop due to multidomain behavior of crystallites for a given value of x. Saturation magnetization increased and remnant magnetization had a maximum as a function of grain size in dependent of x. In turn, coercivity increased with x independent of grain size. Complex permittivity of the Co-Ni-Zn ferrite films was measured in the frequency range 2-15 GHz. The highest hysteretic heating rate in the temperature range 315-355 K was observed in CoFe2O4. The maximum absorption band shifted from 13 to 11GHz as cobalt content increased from x = 0.1 to 0.2.

Interstitial Nitrogen in Diamond – Optical and EPR Studies

Nitrogen is one of the most common impurities in diamond. On a substitutional site it acts as a deep donor, approximately 1.7 eV below the conduction band. Irradiation of nitrogen containing diamond and subsequent annealing creates the nitrogen vacancy centre, which has recently attracted much attention for quantum information processing application. Another possible product of irradiation and annealing of nitrogen containing diamond is interstitial nitrogen. Presumably, a mobile carbon interstitial migrates to a substitutional nitrogen to produce an interstitial nitrogen complex which may or may not be mobile. The configuration(s) of interstitial nitrogen related defects (e.g. bond centred, [001]-split) are not known. An infra-red (IR) absorption peak at 1450 cm-1 labelled H1a has been associated with an nitrogen interstitial complex. [1] Theoretical modelling suggested that this IR local mode is due to a bond centred nitrogen interstitial [2]. However, more recent modelling [3] suggests that this defect is mobile at temperatures were H1a is stable and instead assign H1a to two nitrogen atoms occupying a single lattice site in a [001]-split configuration. To date no electron paramagnetic resonance (EPR) spectra have been conclusively associated with an interstitial nitrogen defect.

In this study we present data from new EPR and optical absorption studies in combination with uniaxial stress of nitrogen interstitial related defects in electron irradiated and annealed nitrogen doped diamond. These measurements yield symmetry information about the defects allowing us to determine which of the proposed models are possible. EPR spectra of nitrogen interstitial related defects in samples isotopically enriched with 15N are reported and we show that these explain the lack of previous EPR data for these defects. Correlations between the IR absorbance and the integrated intensity of the new EPR defects are studied for varying irradiation doses and annealing temperatures.

Melt Processing and Properties of Polyamide 6/Graphene Nanoplatelet Composites

Graphene, due to its outstanding properties, has become the topic of much research activity in recent years. Much of that work has been on a laboratory scale however, if we are to introduce graphene into real product applications it is necessary to examine how the material behaves under industrial processing conditions. In this paper the melt processing of polyamide 6/graphene nanoplatelet composites via twin screw extrusion is investigated and structure–property relationships are examined for mechanical and electrical properties. Graphene nanoplatelets (GNPs) with two aspect ratios (700 and 1000) were used in order to examine the influence of particle dimensions on composite properties. It was found that the introduction of GNPs had a nucleating effect on polyamide 6 (PA6) crystallization and substantially increased crystallinity by up to 120% for a 20% loading in PA6. A small increase in crystallinity was observed when extruder screw speed increased from 50 rpm to 200 rpm which could be attributed to better dispersion and more nucleation sites for crystallization. A maximum enhancement of 412% in Young's modulus was achieved at 20 wt% loading of GNPs. This is the highest reported enhancement in modulus achieved to date for a melt mixed thermoplastic/GNPs composite. A further result of importance here is that the modulus continued to increase as the loading of GNPs increased even at 20 wt% loading and results are in excellent agreement with theoretical predictions for modulus enhancement. Electrical percolation was achieved between 10–15 wt% loading for both aspect ratios of GNPs with an increase in conductivity of approximately 6 orders of magnitude compared to the unfilled PA6.

CSI 2264: Simultaneous Optical and Infrared Light Curves of Young Disk-bearing Stars in NGC 2264 with CoRoT and Spitzer—Evidence for Multiple Origins of Variability

We present the Coordinated Synoptic Investigation of NGC 2264, a continuous 30 day multi-wavelength photometric monitoring campaign on more than 1000 young cluster members using 16 telescopes. The unprecedented combination of multi-wavelength, high-precision, high-cadence, and long-duration data opens a new window into the time domain behavior of young stellar objects. Here we provide an overview of the observations, focusing on results from Spitzer and CoRoT. The highlight of this work is detailed analysis of 162 classical T Tauri stars for which we can probe optical and mid-infrared flux variations to 1% amplitudes and sub-hour timescales. We present a morphological variability census and then use metrics of periodicity, stochasticity, and symmetry to statistically separate the light curves into seven distinct classes, which we suggest represent different physical processes and geometric effects. We provide distributions of the characteristic timescales and amplitudes and assess the fractional representation within each class. The largest category (>20%) are optical "dippers" with discrete fading events lasting ~1-5 days. The degree of correlation between the optical and infrared light curves is positive but weak; notably, the independently assigned optical and infrared morphology classes tend to be different for the same object. Assessment of flux variation behavior with respect to (circum)stellar properties reveals correlations of variability parameters with Hα emission and with effective temperature. Overall, our results point to multiple origins of young star variability, including circumstellar obscuration events, hot spots on the star and/or disk, accretion bursts, and rapid structural changes in the inner disk. Based on data from the Spitzer and CoRoT missions. The CoRoT space mission was developed and is operated by the French space agency CNES, with participation of ESA's RSSD and Science Programmes, Austria, Belgium, Brazil, Germany, and Spain.

Lanthanide oxide nanotubes and nanorods: synthesis, processing, luminescence and catalytic properties

Esta tese relata estudos de síntese, caracterização da estrutura e das propriedades de fotoluminescência e aplicações de nanotubos e nanobastonetes de óxidos de lantanídeos em pontas para microscopia de força atómica, catálise heterogénea e compósitos de base polimérica. Há um interesse crescente em compreender como o confinamento quântico decorrente da redução do tamanho de partícula pode influenciar a eficiência da luminescência, a dinâmica dos estados excitados, a transferência de energia e os efeitos de termalização de nanoluminóforos. Em nanocristais dopados com lantanídeos (Ln3+), e apesar da localização dos estados 4f, ocorrem efeitos de confinamento quântico via interacção com os modos vibracionais da rede. Em particular, a termalização anómala, descrita para uma variedade de nanocristais dopados com Ln3+, tem sido atribuída à ausência de modos vibracionais de menor frequência. Este nanoconfinamento pode ter impacto na dinâmica da luminescência, bem como na transferência de energia mediada por modos vibracionais e processos de upconversion. Nesta tese, relata-se o estudo deste efeito em nanotubos de Gd2O3:Eu3+. A influência de parâmetros como a concentração de európio e as condições de calcinação também foi investigada. Algumas aplicações destes óxidos de lantanídeos também foram exploradas, nomeadamente a modificação de pontas usadas em microscopia de força atómica com nanobastonetes de Gd2O3:Eu3+, lograda através de dielectroforese, técnica que não degrada a emissão de luz (rendimento quântico 0.47). As pontas modificadas são estáveis sob condições de trabalho, podendo ser aplicadas, por exemplo, em microscopia óptica de varrimento de campo próximo (SNOM). A oxidação em fase líquida do etilbenzendo foi investigada usando como catalisador nanotubos de CeO2, em presença dos oxidantes hidroperóxido de t-butilo e H2O2, e do solvente acetonitrilo, e temperaturas entre 55 e 105 ºC. Nanobastonetes de Gd2O3:Eu3+ recobertos com sílica foram preparados pelo método sol-gel. Esta cobertura resultou num aumento, quer do rendimento quântico de emissão, de 0.51 para 0.86 (excitação a 255 nm), quer dos tempos de vida,de 1.43 para 1.80 ms (excitação a 394.4 nm). A superfície dos nanotubos cobertos com sílica foi modificada com o agente de acoplamento metacrilato de 3-(trimetoxissilil)propilo que permitiu a preparação de compósitos através da subsequente polimerização in-situ do estireno por técnicas de miniemulsão e solução. ABSTRACT: This thesis reports on the synthesis, characterisation of the structure and photoluminescence properties, and applications of nanotubes and nanorods of lanthanides oxides in atomic force microscopy tips, heterogeneous catalysis and polymer-base composites. There is a growing interest in understanding how size-dependent quantum confinement affects the photoluminescence efficiency, excited-state dynamics, energy-transfer and thermalisation phenomena in nanophosphors. For lanthanide (Ln3+)-doped nanocrystals, and despite the localisation of the 4f states, confinement effects are induced mostly via electron-phonon interactions. In particular, the anomalous thermalisation reported for a handful of Ln3+-doped nanocrystals has been rationalised by the absence of lowfrequency phonon modes. This nanoconfinement may further impact on the Ln3+ luminescence dynamics, such as phonon-assisted energy transfer or upconversion processes. Here, this effect is investigated in Gd2O3:Eu3+ nanotubes. The influence of parameters such as europium concentration and calcination procedure is also studied. Some applications of these lanthanides oxides have been explored, for instance the modification of atomic force microscopy tips with photoluminescent Gd2O3:Eu3+ nanorods, using dielectrophoresis, a technique which preserves the red emission of the nanorods (quantum yield 0.47). The modified tips are stable under working conditions and may find applications in scanning near-field optical microscopy. The liquid-phase oxidation of ethylbenzene over CeO2 nanotubes has been investigated, using tert-butyl-hydroperoxide and H2O2 as the oxidising agents, and acetonitrile as the solvent, in the range 55-105 ºC. Gd2O3:Eu3+ nanorods have been coated with silica via a sol-gel approach. The silica coating increases both, the Eu3+ absolute emission quantum yields from 0.51 to 0.86 (255 nm excitation), and decay times from 1.43 to 1.80 ms (394.4 nm excitation). The silica coating was modified with 3- (trimethoxysilyl) propyl methacrylate and, subsequently, composites have been prepared by in-situ radical polymerisation of styrene via miniemulsion and solution routes.

Lanthanide-organic frameworks for optical and catalytic applications

Este projecto de doutoramento tem como objetivo isolar e caracterizar sistematicamente novos polímeros de coordenação, no estado sólido. A presença de grupos rígidos possuindo, em particular, átomos de oxigénio e de azoto, deverá induzir interessantes propriedades fotoluminescentes (rendimentos quânticos e tempos de vida elevados, assim como vias de transferência de energia eficientes), que poderão permitir a utilização dos compostos poliméricos na produção de dispositivos funcionais. As diferentes abordagens sintéticas foram ajustadas para cada material e basearam-se, preferencialmente, nas sínteses hidrotérmicas e nas assistidas por radiação de microondas. A estrutura dos materiais foi elucidada a partir de métodos de difracção de raios X (de cristal único ou de pós) em conjunto com outras técnicas, tais como RMN de estado sólido, microscopia eletrónica, análises térmicas, espectroscopia vibracional e estudos de composição elementar. Os compostos microcristalinos foram sistematicamente estudados a fim de investigar outras propriedades além das de fotoluminescência. Alguns dos materiais revelaram multifuncionalidade apresentando simultaneamente tempos de vida na ordem dos milisegundos, elevados rendimentos quânticos e elevado desempenho como catalisadores heterogéneos. As propriedades magnéticas de um composto baseado em érbio foram igualmente estudadas, assim como as de adsorpção e permuta de solvente de uma estrutura porosa baseada em cério.

Nanocomposites for SERS : synthesis, optical and analytical studies

Esta tese descreve diversas estratégias preparativas assim como estudos de caracterização de nanocompósitos e outras nanoestruturas, para a análise em espectroscopia de Raman com intensificação por superfície (SERS). Em particular foi estudada a incorporação de nanopartículas (NPs) metálicas de Ag e Au em matrizes poliméricas visando avaliar o potencial destes materiais como novos substratos para SERS na deteção de moléculas. O primeiro capítulo consiste numa revisão bibliográfica, onde é destacado o desenvolvimento de novos substratos para SERS utilizando nomeadamente nanopartículas de Ag, Au e Cu. Numa primeira fase, esta secção apresenta uma breve descrição sobre as propriedades plasmónicas dos metais utilizados e alguns conceitos básicos de espectroscopia de difusão de Raman. Posteriormente, descreve-se em mais detalhe o efeito de SERS, revendo-se sobretudo a química de materiais descrita em trabalhos recentes tendo em conta a sua utilização como novas plataformas para análise química por SERS. O capítulo 2 descreve a síntese e caracterização de nanocompósitos de poli(acrilato de butilo) obtidos através de polimerização in situ por miniemulsão na presença de nanopartículas de Ag. Os nanocompósitos Ag/PtBA foram investigados como novos substratos de SERS visando o desenvolvimento de novas plataformas versáteis para deteção molecular. Estudos como o efeito da temperatura, pH e pressão foram investigados, visando a compreensão do efeito da matriz polimérica na difusão/adsorção do analito (ácido tiossalicílico) na superfície metálica. No capítulo 3, os nanocompósitos de Ag/PtBA descritos anteriormente foram investigados detalhadamente como substratos para bio-deteção em SERS, usando a adenina como analito modelo. Os nanocompósitos foram submetidos a vários tratamentos pré-analíticos para a bio-deteção da adenina. Foram realizadas experiências nos sistemas Ag/PtBA de modo a obter informação sobre o efeito do pH na deteção deste analito em soluções aquosas diluídas. Os nanocompósitos poliméricos obtidos apresentam a vantagem de poderem ser processados utilizando tecnologia disponível. Pelo que o estudo das suas propriedades térmicas é especialmente relevante. Assim, a influência da incorporação de NPs inorgânicas na temperatura de transição vítrea (Tg) do polímero PtBA foi investigada por meio de calorimetria diferencial de varrimento (DSC) e os resultados são apresentados no capítulo 4. Estes estudos descrevem efeitos na Tg do PtBA quando analisado em nanocompósitos obtidos por diferentes métodos (métodos ex situ e in situ), contendo nanopartículas metálicas com diferentes distribuições de tamanho e presentes em quantidade variável na matriz polimérica. Estes estudos possibilitaram relacionar a influência das NPs metálicas na mobilidade das cadeias poliméricas com as propriedades térmicas observadas. O capítulo 5 descreve a preparação e caracterização de materiais compósitos de base polimérica (PtBA) e NPs de Au com morfologia de bastonetes (NRs). Estes materiais foram investigados como substratos para SERS tendo originado um bom sinal de SERS na análise de 2-2’-ditiodipiridina. Investigouse igualmente o efeito da variação da morfologia das NPs metálicas (esferas e bastonetes), a razão de aspecto (R.A.) dos bastonetes e o tipo de matriz polimérica (PtBA e PnBA) no sinal de SERS. No capítulo 6 é descrita a utilização da técnica de SERS como método alternativo para a monitorização de alterações morfológicas de coloides de NRs de Au. Os NRs de Au foram recolhidos em diferentes fases de oxidação promovida pela presença de K2S2O8 e a sua sensibilidade como substratos de SERS foi avaliada utilizando o anião dietilditiocarbamato (DTC) como analito modelo. Os estudos foram realizados utilizando as linhas de excitação a 1064 nm e 633 nm. Este estudo demonstrou que a sensibilidade dos NRs de Au como substratos de SERS diminui à medida que a sua R.A. diminui devido à competitividade do CTAB (estabilizante) e o DTC pela superfície dos NRs. É de salientar que este processo é acompanhado por um diferente comportamento em termos de adsorção dos dois tautómeros do DTC à superfície do metal. O capítulo 7 introduz um novo tipo de compósitos para SERS, utilizando matrizes biopoliméricas. Assim, descreve-se a preparação e caracterização de nanocompósitos de carragenano e NPs de Ag. Nesta secção é avaliada a utilização destes materiais como novos substratos para a análise em SERS, utilizando a 2-2’-ditiodipiridina como molécula modelo. Descrevem-se estudos pioneiros que procuram relacionar a dependência do sinal de SERS com a força do gel. Para tal, realizou-se um estudo sistemático aos nanobiocompósitos usados como substratos de SERS em diferentes condições analíticas e investigaram-se as suas propriedades reológicas. No capitulo 8 é descrita a investigação de nanocompósitos de Ag/Gelatina como substratos para SERS, utilizando o anião dietilditiocarbamato como analito modelo. Realizaram-se várias experiências para correlacionar a variação da força do gel com o aumento do sinal de SERS bem como a diferente adsorção dos dois tautómeros do DTC à superfície do metal. Ao longo desta dissertação são apresentados metodologias distintas para a preparação e obtenção de nanocompósitos com base em polímeros (sintéticos ou naturais) e NPs metálicas (Ag e Au). Esta investigação não só permitiu a síntese e estudo de novos substratos para SERS mas também a compreensão do efeito matriz/NPs metálicas no sinal de SERS e na formação de “hot spots”. Este trabalho contribui para o enriquecimento na área da Nanociência e Nanotecnologia demonstrando a eficácia e reprodutibilidade de nanocompósitos com base em polímeros como novos substratos para SERS. Embora as propriedades óticas apresentadas por estes materiais serem aqui direcionadas para a deteção molecular pela técnica de SERS, estes materiais podem ser investigados em outras área tecnológicas.

Optical and mechanical analysis on a biological cell in optical tweezers

La réponse mécanique d’une cellule à une force externe permet d’inférer sa structure et fonction. Les pinces optiques s’avèrent une approche particulièrement attrayante pour la manipulation et caractérisation biophysique sophistiquée des cellules de façon non invasive. Cette thèse explore l’utilisation de trois types de pinces optiques couramment utilisées : 1) statiques (static), 2) à exposition partagée (time-sharing) et 3) oscillantes (oscillating). L’utilisation d’un code basé sur la méthode des éléments finis en trois dimensions (3DFEM) nous permet de modéliser ces trois types de piégeage optique afin d’extraire les propriétés mécaniques cellulaires à partir des expériences. La combinaison des pinces optiques avec la mécanique des cellules requiert des compétences interdisciplinaires. Une revue des approches expérimentales sur le piégeage optique et les tests unicellulaires est présentée. Les bases théoriques liant l’interaction entre la force radiative optique et la réponse mécanique de la cellule aussi. Pour la première fois, une simulation adaptée (3DFEM) incluant la diffusion lumineuse et la distribution du stress radiatif permet de prédire la déformation d’une cellule biconcave –analogue aux globules rouges—dans un piège statique double (static dual-trap). À l’équilibre, on observe que la déformation finale est donnée par l’espacement entre les deux faisceaux lasers: la cellule peut être étirée ou même comprimée. L’exposition partagée (time-sharing) est la technique qui permet de maintenir plusieurs sites de piégeage simultanément à partir du même faisceau laser. Notre analyse quantitative montre que, même oscillantes, la force optique et la déformation sont omniprésentes dans la cellule : la déformation viscoélastique et la dissipation de l’énergie sont analysées. Une autre cellule-type, la tige cubique, est étudiée : cela nous permet d’élucider de nouvelles propriétés sur la symétrie de la réponse mécanique. Enfin, l’analyse de la déformation résolue en temps dans un piége statique ou à exposition partagée montre que la déformation dépend simultanément de la viscoélasticité, la force externe et sa forme tridimensionnelle. La technique à force oscillante (oscillating tweezers) montre toutefois un décalage temporel, entre la force et la déformation, indépendant de la forme 3D; cette approche donnerait directement accès au tenseur viscoélastique complexe de la cellule.

Electrical properties of some single crystal dodecaborides /|nby Jyoti Burte. -- 260 St. Catharines [Ont. : s. n.],

PreVi011.3 ':i or~ : indicat e('. tk~t ho t~)rE's sed ~-Al B 12 1i~2, ~' a semiconductor. r:Toreove r , the s i mpl.(~ electronic t heory also indi cates that ~ -AIB1 2 should be a semico nductor, since thf're is one nonbonding e 'Le ctrofl per AlB12- uni t. JPor these reasons, we decided to measure t he electrical n ropert i ~ s of ~ -AlB1 2 single crystal s . Singl e crystal s of¥- AIB 12 ab ou t 1 x 1 r1n1 . size were grown from a copper mel t at 12500 C. The melt technique coupled. 1,vi th slow cooling vilas used because of i ts advantages such as : siTYInle set- up of the expe rimon t ; only e ;l.sil y available c hemi cals are required and it i s a c omparatively strair::bt forvvard y,le t hod still yielding crystal s big enouGh for OtU' purpose . Copper rms used as a solvent , i nst8ad of previOl.wly used aluminum , because it allows c.l.'ystal growth at hig he r t emneratures. HovlGver, the cry s tals of ] -AlB12 shm'red very hi gh res i s t ance a t r oom temperature . From our neasureJ'lents we conclude that the r esistivity of j3- Al B12 is, at least, given as ~ = 4. x 107 oblD .em •• Those results are inc ons i s t ent wi 'uh the ones .. reported by IIiss Khin fo r bot- pressed j3-AlB12 g i ven a s = 7600 ohm . em . or I e s s . ' Since tbe hot pressing was done at about 800 - ' 9000C i n ~ rap hi te moul ds 1,7i th 97% AlB12- p oVJder, vie thi nk there is pas s ib i 1 i ty th a.t lower borides or borot] carbide are , being formed, ':.Jhich are k11 own to be good semiconductors . v7e tried to ro-pe r-AlB12 by addi'J,'?: agents s uch as l:Ig , IG.-InO 4. ' HgS04 , KI12PO 4·' etc. to t he melt .. However , all these re age 11 t eel either reduced the yield and size of t lJe crystals or r;ave crystals of high r esis'can ce again. We think tba t molten copper keeps t he i mpurities off . There is also a pos s i bil i ty t hc:!,t these doping agents get oxidi~::;ed at '1 250°C • Hence, we co ~ clud e that J -AIB12 has v~ ry high r es i stance at r oom temperature . This was a l s o C011 - fi rmed by checki ng the siYlgle and. polycrystals of .~-AIB12 from Norton Co., Ontario and Cooper Nletallurgical Association. Boron carbide has been reported to be a semiconductor with ~ - 0.3 to 0.8 ohm . cm. for hotpres sed s araples. Boron carbide b e inq: struct urally related to ¥-AIB12 , we de cided to study the electrical prone rties of it~ Single crystals. These crystals were cut from a Single melt grovvn crystal a t Norton Co., Ontario. The resistivity of th," se crystal s was measured by the Van der Pam-v' s ~ nethod, which \vas very c onvenient fo r our crystal sha-pp.s. Some of the crystals showed resistivity ~ == 0.50 ob,Tn.cr] . i n agreement with the previously reported results . However , a few crystals showed lower resistivity e.g . 0 .13 and 0.20 ohm.cra • • The Hall mobility could .not be measured and th8reiore i s lower than 0 .16 em 2 v - 1 sec -1 • This is in agreement \vith t he re1)orted Hall mobility for pyrolytic boron . _ 2 -1 -1 carbide as 0.13 cm v sec • We also studied the orientation of the boron carbide crystals by the Jjaue-method. The inclination of c-axis with res pect to x-ray be81Il was det ermined . This was found to be 100 t o 20° f or normal resistivity sarnples (0.5 ohm . cm.) and 27 - 30° for t he lower r esistivity samples (0.1 ~5 to 0.20 ohm.cm .). This indica tes the possibility that th.e r es if.1tivity of B13C3 i s orientation dependent.

Some electrical properties of semi-conductor crystals / |nPhyu Phyu Khin. -- 260 St. Catharines, Ont. : [s. n.],

SiC and AtB 12 have been prepared and their resistivities and Hall voltages measured. The resistivities and Hall voltages were measured by the Van der Pauw's method, using spring loaded tungsten contacts. In this method, the major requirement is to have samples of plane parallel surfaces of arbitrary shape with four small contacts at the circumference. Similar measurements were made with a number of SiC crystals obtained from the Norton Research Corporation (Canada)-Ltd., Carolina Aluminum Co., Exolon Co. and Carborundum Co. It was found that resistivity, carrier concentration and mobility of ions depend on the type of impurity. AtB 12 was prepared from the melt containing At and B in the ratio of 4:1. They formed amber-colour pseudo tetragonal crystals. As the crystals obtained were small for electrical measurements, hot pressed lumps have been used to measure their resistivity.

Growth and Characterization of ZnO based Heterojunction diodes and ZnO Nanostructuresby Pulsed Laser Ablation

Transparent conducting oxides (TCO’s) have been known and used for technologically important applications for more than 50 years. The oxide materials such as In2O3, SnO2 and impurity doped SnO2: Sb, SnO2: F and In2O3: Sn (indium tin oxide) were primarily used as TCO’s. Indium based oxides had been widely used as TCO’s for the past few decades. But the current increase in the cost of indium and scarcity of this material created the difficulty in obtaining low cost TCO’s. Hence the search for alternative TCO material has been a topic of active research for the last few decades. This resulted in the development of various binary and ternary compounds. But the advantages of using binary oxides are the easiness to control the composition and deposition parameters. ZnO has been identified as the one of the promising candidate for transparent electronic applications owing to its exciting optoelectronic properties. Some optoelectronics applications of ZnO overlap with that of GaN, another wide band gap semiconductor which is widely used for the production of green, blue-violet and white light emitting devices. However ZnO has some advantages over GaN among which are the availability of fairly high quality ZnO bulk single crystals and large excitonic binding energy. ZnO also has much simpler crystal-growth technology, resulting in a potentially lower cost for ZnO based devices. Most of the TCO’s are n-type semiconductors and are utilized as transparent electrodes in variety of commercial applications such as photovoltaics, electrochromic windows, flat panel displays. TCO’s provide a great potential for realizing diverse range of active functions, novel functions can be integrated into the materials according to the requirement. However the application of TCO’s has been restricted to transparent electrodes, ii notwithstanding the fact that TCO’s are n-type semiconductors. The basic reason is the lack of p-type TCO, many of the active functions in semiconductor originate from the nature of pn-junction. In 1997, H. Kawazoe et al reported the CuAlO2 as the first p-type TCO along with the chemical design concept for the exploration of other p-type TCO’s. This has led to the fabrication of all transparent diode and transistors. Fabrication of nanostructures of TCO has been a focus of an ever-increasing number of researchers world wide, mainly due to their unique optical and electronic properties which makes them ideal for a wide spectrum of applications ranging from flexible displays, quantum well lasers to in vivo biological imaging and therapeutic agents. ZnO is a highly multifunctional material system with highly promising application potential for UV light emitting diodes, diode lasers, sensors, etc. ZnO nanocrystals and nanorods doped with transition metal impurities have also attracted great interest, recently, for their spin-electronic applications This thesis summarizes the results on the growth and characterization of ZnO based diodes and nanostructures by pulsed laser ablation. Various ZnO based heterojunction diodes have been fabricated using pulsed laser deposition (PLD) and their electrical characteristics were interpreted using existing models. Pulsed laser ablation has been employed to fabricate ZnO quantum dots, ZnO nanorods and ZnMgO/ZnO multiple quantum well structures with the aim of studying the luminescent properties.

Synthesis and Characterization of Some Organic Semiconductors and Investigations on the Effect of Swift Heavy Ions on Their Properties

In this work polymers belonging to polyaniline and polyaniline doped with camphor sulphonic acid are synthesised. Cobalt phthalocyanine is an interesting candidate belonging to the tetramers. Studies on the composites containing cobalt phthalocyanine tetramer and polyaniline doped with camphor sulphonic acid for various concentration are also undertaken in order to understand the mechanism. RF plasma polymerised aniline and furfural are prepared. The structural and electrical properties are evaluated. The bombardment of swift heavy ions of these films are carried out and the effect of irradiation on their properties is also investigated.

Evaluation of Magnetic,Dielectric and Mechanical Properties of Rubber Ferrite Composites

In the present study the preparation and characterisation of rubber ferrite composites (RFC) containing barium ferrite (BaF) and strontium ferrite (SrF) have been dealt with. The incorporation of the hard ferrites into natural and nitrile rubber was carried out according to a specific recipe for various loadings of magnetic fillers. For this, the ferrite materials namely barium ferrite and strontium ferrite having the general formula MO6Fe2O3 have been prepared by the conventional ceramic techniques. After characterisation they were incorporated into the natural and nitrile rubber matrix by mechanical method. Carbon black was also incorporated at different loading into the rubber ferrite composites to study its effect on various properties. The cure characteristics, mechanical, dielectric and magnetic properties of these composites were evaluated. The ac electrical conductivity of both the ceramic ferrites and rubber ferrite composites were also calculated using a simple relation. The investigations revealed that the rubber ferrite composites with the required dielectric and magnetic properties can be obtained by the incorporation of ferrite fillers into the rubber matrix, without compromising much on the processability and mechanical properties.

Investigations on Photoconductivity and Electrical Switiching in Selected Chalcogenide Glasses

In this thesis, we present the results of our investigations on the photoconducting and electrical switching properties of selected chalcogenide glass systems. We have used XRD and X-ray photoelectron spectroscopy (XPS) analysis for confinuing the amorphous nature of these materials and for confirming their constituents respectively.Photoconductivity is the enhancement in electrical conductivity of materials brought about by the motion of charge carriers excited by absorbed radiation. The phenomenon involves absorption, photogeneration, recombination and transport processes and it gives good insight into the density of states in the energy gap of solids due to the presence of impurities and lattice defects. Photoconductivity measurements lead to the determination of such important parameters as quantum efficiency, photosensiti\'ity, spectral sensitivity and carrier lifetime. Extensive research work on photoconducting properties of amorphous semiconductors has resulted in the development of a variety of very sensitive photodetectors. Photoconductors are finding newer and newer uses eyery day. CdS, CdSe. Sb2S3, Se, ZnO etc, are typical photoconducting materials which are used in devices like vidicons, light amplifiers, xerography equipment etc.Electrical switching is another interesting and important property possessed by several Te based chalcogenides. Switching is the rapid and reversible transition between a highly resistive OFF state, driven by an external electric field and characterized by a threshold voltage, and a low resistivity ON state, Switching can be either threshold type or memory type. The phenomenon of switching could find applications in areas like infonnation storage, electrical power control etc. Investigations on electrical switching in chalcogenide glasses help in understanding the mechanism of switching which is necessary to select and modify materials for specific switching applications.Analysis of XRD pattern gives no further infonuation about amorphous materials than revealing their disordered structure whereas x-ray photoelectron spectroscopy,XPS) provides information about the different constituents present in the material. Also it gives binding energies (b.e.) of an element in different compounds and hence b.e. shift from the elemental form.Our investigations have been concentrated on the bulk glasses, Ge-In-Se, Ge-Bi-Se and As-Sb-Se for photoconductivity measurements and In-Te for electrical switching. The photoconducting properties of Ge-Sb-Se thin films prepared by sputtering technique have also been studied. The bulk glasses for the present investigations are prepared by the melt quenching technique and are annealed for half an hour at temperatures just below their respective glass transition temperatures. The dependence of photoconducting propenies on composition and temperature are investigated in each system. The electrical switching characteristics of In-Te system are also studied with different compositions and by varying the temperature.