Polymer surface modification by atomic layer deposition

Current industrial atomic layer deposition (ALD) processes are almost wholly confined to glass or silicon substrates. For many industrial applications, deposition on polymer substrates will be necessary. Current deposition processes are also typically carried out at temperatures which are too high for polymers. If deposition temperatures in ALD can be reduced to the level applicable for polymers, it will open new interesting areas and applications for polymeric materials. The properties of polymers can be improved for example by coatings with functional and protective properties. Although the ALD has shown its capability to operate at low temperatures suitable for polymer substrates, there are other issues related to process efficiency and characteristics of different polymers where new knowledge will assist in developing industrially conceivable ALD processes. Lower deposition temperature in ALD generally means longer process times to facilitate the self limiting film growth mode characteristic to ALD. To improve process efficiency more reactive precursors are introduced into the process. For example in ALD oxide processes these can be more reactive oxidizers, such as ozone and oxygen radicals, to substitute the more conventionally used water. Although replacing water in the low temperature ALD with ozone or plasma generated oxygen radicals will enable the process times to be shortened, they may have unwanted effects both on the film growth and structure, and in some cases can form detrimental process conditions for the polymer substrate. Plasma assistance is a very promising approach to improve the process efficiency. The actual design and placement of the plasma source will have an effect on film growth characteristics and film structure that may retard the process efficiency development. Due to the fact that the lifetime of the radicals is limited, it requires the placement of the plasma source near to the film growth region. Conversely this subjects the substrate to exposure byother plasma species and electromagnetic radiation which sets requirements for plasma conditions optimization. In this thesis ALD has been used to modify, activate and functionalize the polymer surfaces for further improvement of polymer performance subject to application. The issues in ALD on polymers, both in thermal and plasma-assisted ALD will be further discussed.

Growth, magnetic and transport properties of InSb and II-IV-As2 semiconductors doped with manganese

This thesis is devoted to growth and investigations of Mn-doped InSb and II-IV-As2 semiconductors, including Cd1-xZnxGeAs2:Mn, ZnSiAs2:Mn bulk crystals, ZnSiAs2:Mn/Si heterostructures. Bulk crystals were grown by direct melting of starting components followed by fast cooling. Mn-doped ZnSiAs2/Si heterostructures were grown by vacuum-thermal deposition of ZnAs2 and Mn layers on Si substrates followed by annealing. The compositional and structural properties of samples were investigated by different methods. The samples consist of micro- and nano- sizes clusters of an additional ferromagnetic Mn-X phases (X = Sb or As). Influence of magnetic precipitations on magnetic and electrical properties of the investigated materials was examined. With relatively high Mn concentration the main contribution to magnetization of samples is by MnSb or MnAs clusters. These clusters are responsible for high temperature behavior of magnetization and relatively high Curie temperature: up to 350 K for Mn-doped II-IV-As2 and about 600 K for InMnSb. The low-field magnetic properties of Mn-doped II-IV-As2 semiconductors and ZnSiAs2:Mn/Si heterostructures are connected to the nanosize MnAs particles. Also influence of nanosized MnSb clusters on low-field magnetic properties of InMnSb have been observed. The contribution of paramagnetic phase to magnetization rises at low temperatures or in samples with low Mn concentration. Source of this contribution is not only isolated Mn ions, but also small complexes, mainly dimmers and trimmers formed by Mn ions, substituting cation positions in crystal lattice. Resistivity, magnetoresistance and Hall resistivity properties in bulk Mn-doped II-IV-As2 and InSb crystals was analyzed. The interaction between delocalized holes and 3d shells of the Mn ions together with giant Zeeman splitting near the cluster interface are respond for negative magnetoresistance. Additionally to high temperature critical pointthe low-temperature ferromagnetic transition was observed Anomalous Hall effect was observed in Mn doped samples and analyzed for InMnSb. It was found that MnX clusters influence significantly on magnetic scattering of carriers.

Color change and quality response of ‘lane late’ orange submitted to degreening process

This study aimed at evaluating the effects of ethylene on peel color and compositional changes in ‘Lane late’ orange stored under refrigerated and ambient conditions. Physiologically mature, but green-peeled, oranges were exposed to ethylene gas under room temperature and high relative humidity for 24 hours. Storage chamber was ventilated with fresh air after 12 hours to mitigate consequences derived from fruit respiration. Both nondestructive analysis, such as peel color (hue angle, chromaticity, and brightness) and weight loss, and destructive ones (soluble solids, titratable acidity, pH, soluble solids to acidity ratio, and puncture force) were performed upon harvest, after degreening, and every three days during eighteen days in storage. Experiment was carried out using an entirely randomized design with thirty replications for nondestructive and four replications for destructive analyses, in a split plot scheme. Exposure to ethylene ensured a golden yellow peel for both fruit stored under ambient and refrigerated conditions. High relative humidity, associated with low temperature prevented fruit from losing moisture. Fruit exposure to ethylene did not affect weight loss, soluble solids, titratable acidity, pH, soluble solids, acidity ratio, or puncture force.

Comparison of diffusion models for description of osmotic dehydration of radish slices dipped in brine

ABSTRACT This paper aims at describing the osmotic dehydration of radish cut into cylindrical pieces, using one- and two-dimensional analytical solutions of diffusion equation with boundary conditions of the first and third kind. These solutions were coupled with an optimizer to determine the process parameters, using experimental data. Three models were proposed to describe the osmotic dehydration of radish slices in brine at low temperature. The two-dimensional model with boundary condition of the third kind well described the kinetics of mass transfers, and it enabled prediction of moisture and solid distributions at any given time.

Advanced welding technologies used for arctic metal structures

Rapid depletion of easy-to-access fossil fuel, predominantly, oil and gas resources has now necessitated increase in need to develop new oil and gas sources in ever more remote and hostile environments. This is necessary in order to explore more oil and gas resources to meet rapidly rising long-term energy demand in the world, both at present and in the nearest future. Arctic is one of these harsh environments, where enormous oil and gas resources are available, containing about 20% of the world total oil and gas, but the environmental conditions are very harsh and hostile. However, virtually all the facilities required for the exploration and development of this new energy source are constructed with metals as well as their alloys and are predominantly joined together by welding processes and technologies. Meanwhile, due to entirely different environment from the usual moderate temperate region, conventional welding technologies, common metals and their alloys cannot be applied as this Arctic environment demand metals structures with very high toughness and strength properties under extremely low temperature. This is due to the fact that metals transit from ductility to brittleness as the temperature moves toward extreme negative values. Hence, this research work investigates and presents the advanced welding technologies applicable to Arctic metal structures which can give satisfactory weldments under active Arctic service conditions. .

Lujien hitsattavien terästen käyttäytyminen -60 °C:ssa

Opinnäytetyö on osa Arctic Materials Technologies Development -projektia, jonka tavoitteena on kehittää perusteita arktisten alueiden sovelluksiin suunnittelun ja valmistuksen kannalta. Arktisella alueella sijaitsee useita potentiaalisia öljy- ja maakaasuesiintymiä, joiden hyödyn-täminen tulee vuosi vuodelta kannattavammaksi ilmaston lämpenemisestä johtuvan merijään heikkenemisen vuoksi. Alin suunnittelulämpötila arktisilla alueilla on -60 °C, mikä aiheuttaa haasteita sekä materiaalinvalinnalle että hitsaukselle. Ferriittisillä teräksillä esiintyy lämpötilasta riippuvaa sitkeyden vaihtelua, jota kutsutaan transi-tiokäyttäytymiseksi. Lämpötilan laskiessa teräksen iskusitkeys sekä murtumissitkeys laske-vat. Arktisissa sovelluskohteissa käytetään yleisesti niukkaseosteisia, mikroseostettuja hie-noraeteräksiä, joille on ominaista erinomaiset sitkeys-, lujuus- sekä hitsattavuusominaisuudet vaativissakin olosuhteissa. Lujat termomekaanisesti valssatut ja nuorrutetut hienoraeteräkset kattavat myötölujuusluokat 355…700 MPa. Tutkimuksissa on saatu vaihtelevia tuloksia ma-teriaalien isku- ja murtumissitkeydestä -60 °C:ssa. Erityisesti sitkeysominaisuudet hitsiaineen ja muutosvyöhykkeen alueiden välillä ovat vaihtelevia. Pienemmällä lämmöntuonnilla ja seostetuilla lisäaineilla saavutetaan kuitenkin pääsääntöisesti parempia sitkeysarvoja. Asiku-laarinen ferriitti sekä alabainiitti ovat toivottavia mikrorakenteita liitoksessa, niiden pienen raekoon johdosta.

Rasvankestävät paperit ja kartongit

Rasvankestävyydellä tarkoitetaan sitä, että materiaali hylkii tai kestää rasvaa tietyn ajan läpäisemättä sen pintaa. Rasvankestäviä papereita ja kartonkeja löytyy kaikkialta. Erilaiset ruuanvalmistuspaperit, kuten esimerkiksi leivinpaperi ja voipaperi, ovat rasvankestäviä. Myös pakkauksissa käytetään paljon rasvankestäviä papereita ja kartonkeja. Rasvankestäviltä tuotteilta vaaditaan erilaisia ominaisuuksia riippuen niiden käyttötarkoituksesta. Pakkausmateriaaleilta vaaditaan esimerkiksi lujuutta ja kestävyyttä fyysistä rasitusta, valoa, hajuja ja mikrobeja vastaan. Ruuanvalmistusmateriaaleilta vaaditaan puolestaan lujuutta ja kestävyyttä lämpöä, kosteutta ja fyysistä rasitusta vastaan. Rasvankestäviltä papereilta vaaditaan rasvankestävyyden lisäksi hyvää vetolujuutta, märkälujuutta ja hyviä optisia ominaisuuksia. Neliömassan tulee asettua 20─80 g/m2 välille ja metallipitoisuudet eivät saa olla liian korkeat. Myös tuotteiden kierrätettävyys on nostanut asemaansa viimeaikoina. Tuotteen tuotannon ja itse tuotteen ympäristöystävällisyys ovat todella arvostettuja kuluttajan, tuottajan, Suomen, EU:n ja koko maailman näkökulmista. Jotta tuotteesta saadaan rasvankestävää, vaaditaan siltä erilaisia barrier-ominaisuuksia. Rasvankestävällä paperilla vaaditaan hyviä barrier-ominaisuuksia esimerkiksi rasvan, ilman, veden, vesihöyryn sekä hapen läpäisevyyksissä. Rasvankestäviä papereita ja kartonkeja voidaan valmistaa kemiallisilla ja mekaanisilla tavoilla. Happokäsittely ja fluorokemikaalien lisääminen ovat kemiallisia tapoja, kun taas sellun jauhaminen pitkään matalassa lämpötilassa on mekaaninen tapa valmistaa rasvankestävää paperia. Näiden tapojen lisäksi rasvankestäviä papereita voidaan tehdä erilaisten pinnoitusten avulla. Erilaiset muovit ovat yleisemmin käytettyjä pinnoitemateriaaleja. Esimerkiksi PE- ja PET-päällysteet ovat käytettyjä rasvankestävissä tuotteissa. Viime aikoina on kehitetty paljon erilaisia biomateriaaleja, joista voidaan tehdä rasvankestävä pinnoite. Lipideistä, hydrokolloideista ja erilaisista komposiiteista voidaan luoda uusien tekniikoiden avulla rasvankestäviä pinnoitteita. Rasvankestävyydestä voidaan saada jonkinlainen käsitys WVTR-asteen, Cobb-arvon ja kontaktikulman mittausten avulla. Rasvankestävyyttä voidaan myös mitata erilaisten standarditestien avulla. TAPPI:lla, ISO:lla ja ASTM:llä on useita erilaisia standardeja. Lähes kaikissa rasvankestävyysstandardeissa tuloksen saaminen perustuu visuaaliseen havaintoon, mikä aiheuttaa välillä hankaluuksia tulosten luotettavuuteen, koska tuloksen määrittää ihmissilmä, ja kaikilla testin tekijöillä on erilainen silmä, joka aistii eri tavalla.

Characterisation of Laser Beam and Paper Material Interaction

It is known already from 1970´s that laser beam is suitable for processing paper materials. In this thesis, term paper materials mean all wood-fibre based materials, like dried pulp, copy paper, newspaper, cardboard, corrugated board, tissue paper etc. Accordingly, laser processing in this thesis means all laser treatments resulting material removal, like cutting, partial cutting, marking, creasing, perforation etc. that can be used to process paper materials. Laser technology provides many advantages for processing of paper materials: non-contact method, freedom of processing geometry, reliable technology for non-stop production etc. Especially packaging industry is very promising area for laser processing applications. However, there are only few industrial laser processing applications worldwide even in beginning of 2010´s. One reason for small-scale use of lasers in paper material manufacturing is that there is a shortage of published research and scientific articles. Another problem, restraining the use of laser for processing of paper materials, is colouration of paper material i.e. the yellowish and/or greyish colour of cut edge appearing during cutting or after cutting. These are the main reasons for selecting the topic of this thesis to concern characterization of interaction of laser beam and paper materials. This study was carried out in Laboratory of Laser Processing at Lappeenranta University of Technology (Finland). Laser equipment used in this study was TRUMPF TLF 2700 carbon dioxide laser that produces a beam with wavelength of 10.6 μm with power range of 190-2500 W (laser power on work piece). Study of laser beam and paper material interaction was carried out by treating dried kraft pulp (grammage of 67 g m-2) with different laser power levels, focal plane postion settings and interaction times. Interaction between laser beam and dried kraft pulp was detected with different monitoring devices, i.e. spectrometer, pyrometer and active illumination imaging system. This way it was possible to create an input and output parameter diagram and to study the effects of input and output parameters in this thesis. When interaction phenomena are understood also process development can be carried out and even new innovations developed. Fulfilling the lack of information on interaction phenomena can assist in the way of lasers for wider use of technology in paper making and converting industry. It was concluded in this thesis that interaction of laser beam and paper material has two mechanisms that are dependent on focal plane position range. Assumed interaction mechanism B appears in range of average focal plane position of 3.4 mm and 2.4 mm and assumed interaction mechanism A in range of average focal plane position of 0.4 mm and -0.6 mm both in used experimental set up. Focal plane position 1.4 mm represents midzone of these two mechanisms. Holes during laser beam and paper material interaction are formed gradually: first small hole is formed to interaction area in the centre of laser beam cross-section and after that, as function of interaction time, hole expands, until interaction between laser beam and dried kraft pulp is ended. By the image analysis it can be seen that in beginning of laser beam and dried kraft pulp material interaction small holes off very good quality are formed. It is obvious that black colour and heat affected zone appear as function of interaction time. This reveals that there still are different interaction phases within interaction mechanisms A and B. These interaction phases appear as function of time and also as function of peak intensity of laser beam. Limit peak intensity is the value that divides interaction mechanism A and B from one-phase interaction into dual-phase interaction. So all peak intensity values under limit peak intensity belong to MAOM (interaction mechanism A one-phase mode) or to MBOM (interaction mechanism B onephase mode) and values over that belong to MADM (interaction mechanism A dual-phase mode) or to MBDM (interaction mechanism B dual-phase mode). Decomposition process of cellulose is evolution of hydrocarbons when temperature is between 380- 500°C. This means that long cellulose molecule is split into smaller volatile hydrocarbons in this temperature range. As temperature increases, decomposition process of cellulose molecule changes. In range of 700-900°C, cellulose molecule is mainly decomposed into H2 gas; this is why this range is called evolution of hydrogen. Interaction in this range starts (as in range of MAOM and MBOM), when a small good quality hole is formed. This is due to “direct evaporation” of pulp via decomposition process of evolution of hydrogen. And this can be seen can be seen in spectrometer as high intensity peak of yellow light (in range of 588-589 nm) which refers to temperature of ~1750ºC. Pyrometer does not detect this high intensity peak since it is not able to detect physical phase change from solid kraft pulp to gaseous compounds. As interaction time between laser beam and dried kraft pulp continues, hypothesis is that three auto ignition processes occurs. Auto ignition of substance is the lowest temperature in which it will spontaneously ignite in a normal atmosphere without an external source of ignition, such as a flame or spark. Three auto ignition processes appears in range of MADM and MBDM, namely: 1. temperature of auto ignition of hydrogen atom (H2) is 500ºC, 2. temperature of auto ignition of carbon monoxide molecule (CO) is 609ºC and 3. temperature of auto ignition of carbon atom (C) is 700ºC. These three auto ignition processes leads to formation of plasma plume which has strong emission of radiation in range of visible light. Formation of this plasma plume can be seen as increase of intensity in wavelength range of ~475-652 nm. Pyrometer shows maximum temperature just after this ignition. This plasma plume is assumed to scatter laser beam so that it interacts with larger area of dried kraft pulp than what is actual area of beam cross-section. This assumed scattering reduces also peak intensity. So result shows that assumably scattered light with low peak intensity is interacting with large area of hole edges and due to low peak intensity this interaction happens in low temperature. So interaction between laser beam and dried kraft pulp turns from evolution of hydrogen to evolution of hydrocarbons. This leads to black colour of hole edges.

Matalalämpötilaisen hukkalämmön hyödyntäminen kaukolämmön tuotannossa

Työ käsittelee tekniikoita, joilla voidaan hyödyntää matalalämpötilaisia hukkalämpöjä kaukolämmöntuotannossa. Työ esittelee lämpöpumpputekniikkaa, jolla hukkalämmön lähteestä tulevaa lämpöä voidaan lämpötilaltaan nostaa kaukolämpöverkon tarpeita vastaavaksi. Työssä käsitellään lämpöpumppujen kylmäaineita ja niiden soveltuvuutta eri lämpötila-alueisiin. Lisäksi käsitellään hyödyntämisen taloudellisuutta ja ympäristövaikutuksia. Taloudellisuudessa käsitellään investointi- ja käyttökustannukset ja pohditaan niiden pohjalta tuotteiden kaukolämpö- ja kaukokylmähinnoittelua asiakkaille. Työ myös tarkastelee hankkeen kokonaiskannattavuutta Mäntsälän Sähkölle. Kannattavuuslaskelmissa toteutetaan herkkyystarkastelu suurimpien muuttujien osalta. Työ tarkastelee yhdistetyn kylmän- ja lämmöntuotannon soveltuvuutta Mäntsälän keskustan kaukolämpöverkon ja Kapulin kaukolämpöverkon alueelle. Soveltuvuutta tarkastellaan Suomessa ja maailmalla toteutettujen referenssien pohjalta.

Työkoneiden dieselmoottoreiden hyötysuhteen parantaminen lämmöntalteenoton avulla

Tämä diplomityö on osa Lappeenrannan teknillisessä yliopistossa tehtävää tutkimusta polttomoottoreiden energiatehokkuuden parantamisessa. Työn tavoitteena on saada tutkimustietoa polttomoottoreiden hukkalämpövirtojen hyödyntämisestä sähköntuotannossa. Tavoitteena on muodostaa näkemys Mikro-ORC energiamuuntimen mahdollisuuksista ja reunaehdoista osana työkoneluokan (150 kW… 400 kW) dieselmoottorikokonaisuutta, erityisesti maataloussektorilla. Työssä tarkasteltaviksi moottoreiksi valittiin kaksi eri AGCO Sisu Powerin dieselmoottoria. Laskennat suoritettiin moottorin valmistajan antamien hukkalämpövirtojen arvojen perusteella. Laskennan perusperiaatteena oli tutkia ORC-prosessin tuottamaa lisäsähkötehoa hyödyntämällä pakokaasujen lämpöenergiaa korkea-, keski- ja matalalämpötiloissa. Työssä vertailtiin kahden eri kiertoaineen prosessihyötysuhdetta, saatava sähkötehoa sekä prosessin sisäisiä parametreja. Lisäksi työssä tutkittiin ORC-prosessin laskentaa suunnittelupisteessä (design) ja suunnittelupisteen ulkopuolella (off-design), prosessisuureiden optimointia ja lämmönsiirtimien mitoitusta. Diplomityössä tarkasteltiin moottorin energiataseen mukaisten arvojen lisäksi moottorin parametrien muuttamisen vaikutusta hukkalämpövirroista saatavan tehoon. Työssä saatiin arvokasta tietoa polttomoottoreiden hukkalämpövirtojen muuntamisesta sähköksi ORC:lla sekä moottorin energiatehokkuuden parantamisesta.

Defining of the material models for stainless steels to be used in FE modeling

The aim of this work is to study the results of tensile tests for austenitic stainless steel type 304 and make accurate FE-models according to the results of the tests. Tensile tests were made at Central Research Institute of Structural Material, Prometey at Saint Petersburg and Mariyenburg in Russia. The test specimens for the tensile tests were produced at Lappeenranta University of Technology in a Laboratory of Steel Structures. In total 4 different tests were made, two with base material specimens and two with transverse butt weld specimens. Each kind of a specimen was tested at room temperature and at low temperature. By comparing the results of room and low temperature tests of similar test specimen we get to study the results of work hardening that affect the austenitic steels at below room temperature. The produced specimens are to be modeled accurately and then imported for nonlinear FEM- analyzing. Using the data gained from the tensile tests the aim is to get the models work like the specimens did during the tests. By using the analyzed results of the FE-models the aim is to calculate and get the stress-strain curves that correspond to the results acquired from the tensile tests.

Competitiveness of ALS inhibitors resistant and susceptible biotypes of Greater Beggarticks (Bidens subalternans)

The continuous use of ALS-inhibiting herbicides has led to the evolution of herbicide-resistant weeds worldwide. Greater beggarticks is one of the most troublesome weeds found in the soybean production system in Brazil. Recently, a greater beggarticks biotype that is resistant (R) to ALS inhibitors due to Trp574Leu mutation in the ALS gene was identified. Also, the adaptive traits between susceptible (S) and R to ALS inhibitors biotypes of greater beggarticks were compared. Specifically, we aimed to: (1) evaluate and compare the relative growth rates (RGR) between the biotypes; (2) analyze the seed germination characteristics of R and S biotypes under different temperature conditions; and (3) evaluate their competitive ability in a replacement series study. The experiments were conducted at the University of Arkansas, USA, in 2007 and at Universidade Federal do Rio Grande do Sul (Federal University of Rio Grande do Sul), Brazil, in 2008. Plant proportions for replacement series studies were respectively 100:0, 75:25, 50:50, 25:75 and 0:100, with a total population of 150 plants m-2. There was no difference in RGR between R and S biotypes. The R-biotype germination rate was lower than that of the S biotype. However, at low temperature conditions (15 ºC), the reverse was observed. In general, there is no difference in the competitive ability between R and S greater beggarticks biotypes.

Characterization of Leaf-Type Ferredoxin-NADP+ Oxidoreductase (FNR) Isoforms in Arabidopsis thaliana

Life on earth is based on sunlight, which is captured in chemical form by photosynthetic reactions. In the chloroplasts of plants, light reactions of photosynthesis take place at thylakoid membranes, whereas carbon assimilation reactions occur in the soluble stroma. The products of linear electron transfer (LET), highly-energetic ATP molecules, and reducing power in the form of NADPH molecules, are further used in the fixation of inorganic CO2 molecules into organic sugars. Ferredoxin-NADP+ oxidoreductase (FNR) catalyzes the last of the light reactions by transferring electrons from ferredoxin (FD) to NADP+. In addition to LET, FNR has been suggested to play a role in cyclic electron transfer (CET), which produces ATP without the accumulation of reducing equivalents. CET is proposed to occur via two putative routes, the PGR5- route and the NDH-route. In this thesis, the leaf-type FNR (LFNR) isoforms LFNR1 and LFNR2 of a model organism, Arabidopsis thaliana, were characterized. The physiological roles of LFNRs were investigated using single and double mutant plants. The viability of the single mutants indicates functionality of both isoforms, with neither appearing to play a specific role in CET. The more severe phenotype of low-temperature adapted fnr2 plants compared to both wild-type (WT) and fnr1 plants suggests a specific role for LFNR2 under unfavorable growth conditions. The more severe phenotype of the fnr1 x fnr2 (F1 generation) plants compared to single mutants reflects down-regulated photosynthetic capacity, whereas slightly higher excitation pressure indicates mild over-excitation of electron transfer chain (ETC). However, induction of CET and various photoprotective mechanisms enable adaptation of fnr1 x fnr2 plants to scarcity of LFNR. The fnr1 fnr2 plants (F2 generation), without detectable levels of LFNR, were viable only under heterotrophic conditions. Moreover, drought stress induced acceleration of the rate of P700 + re-reduction in darkness was accompanied by a concomitant up-regulation of the PGR5-route specific components, PGR5 and PGRL1, demonstrating the induction of CET via the PGR5-route. The up-regulation of relative transcriptional expression of the FD1 gene indicates that the FD1 isoform may have a specific function in CET, while no such role could be defined for either of the LFNR isoforms. Both the membrane-bound and soluble LFNR1 and LFNR2 each appear as two distinct spots after 2D-PAGE with different isoelectric points (pIs), indicating the existence of post-translational modifications (PTMs) which do not determine the membrane attachment of LFNR. The possibility of phosphorylation and glycosylation PTMs were excluded, but all four LFNR forms were shown to contain acetylated lysine residues as well as alternative N-termini. N-terminal acetylation was shown to shift the pI of both LFNRs to be more acidic. In addition, all four LFNR forms were demonstrated to interact both with FD1 and FD2 in vitro

Industrial-Scale hydrothermal carbonization of waste sludge materials for fuel production

Hydrothermal carbonization (HTC) is a thermochemical process used in the production of charred matter similar in composition to coal. It involves the use of wet, carbohydrate feedstock, a relatively low temperature environment (180 °C-350 °C) and high autogenous pressure (up to 2,4 MPa) in a closed system. Various applications of the solid char product exist, opening the way for a range of biomass feedstock materials to be exploited that have so far proven to be troublesome due to high water content or other factors. Sludge materials are investigated as candidates for industrial-scale HTC treatment in fuel production. In general, HTC treatment of pulp and paper industry sludge (PPS) and anaerobically digested municipal sewage sludge (ADS) using existing technology is competitive with traditional treatment options, which range in price from EUR 30-80 per ton of wet sludge. PPS and ADS can be treated by HTC for less than EUR 13 and 33, respectively. Opportunities and challenges related to HTC exist, as this relatively new technology moves from laboratory and pilot-scale production to an industrial scale. Feedstock materials, end-products, process conditions and local markets ultimately determine the feasibility of a given HTC operation. However, there is potential for sludge materials to be converted to sustainable bio-coal fuel in a Finnish context.

Morphology, reproduction and development of Hypoglossum hypoglossoides (Stackhouse) Collins & Hervey (Ceramiales, Rhodophyta) from the south and southeastern Brazilian coast

Hypoglossum hypoglossoides (Stackhouse) Collins & Hervey is reported for the first time from the infralittoral of São Paulo and Santa Catarina states. The species was already reported to the states of Rio de Janeiro, Espírito Santo and Bahia as Hypoglossum tenuifolium (Harvey) J. Agardh var. carolinianum Williams. A detailed description of the morphology and reproduction is given based on field-collected material. Unialgal cultures were initiated from tetraspore germination, and growth rates of gametophytes were determined under different conditions of temperature, photoperiod and irradiance. Gametophytes grew well between 15 to 30 ºC, 14L:10D and 10L:14D photoperiods and irradiance from 20 to 120 µmol photons.m-2.s-1, but presented low percentage of fertile plants in low temperature (15 ºC). Gametophytes cultured in laboratory developed only male reproductive structures. Physiological responses of H. hypoglossoides indicate that the species is well adapted to temperature and light variations which could explain its range of vertical (6-26 m depth) and latitudinal distribution (from Fernando de Noronha to Santa Catarina) as well as the absence of sexual reproduction in the southern limit of its distribution.