Effect of Two Restorative Materials on Root Dentine Erosion

This study sought to evaluate the microhardness of root dentine adjacent to glass-ionomer and composite resin restorations after erosive challenge. A crossover study was performed in two phases of 4 consecutive days each. One hundred twelve bovine root dentine slabs were obtained, and standardized box-shaped cavities were prepared at center of each specimen. The prepared cavities were randomly restored with glass-ionomer cement or composite resin. The slabs were randomly assigned among 14 volunteers, which wore intraoral palatal device containing four restored root dentin slabs. Starting on the second day, half of the palatal acrylic devices were immersed extraorally in a lemonade-like carbonated soft drink for 90 s, four times daily for 3 days. Alter 3-day wash-out, dentine slabs restored with the alternative material were placed into palatal appliance and the volunteers started the second phase of this study. After erosive challenges. microhardness measurements were performed. Regardless of the restorative material employed, eroded specimens demonstrated lower microhardness value (p < 0.0001). At eroded condition examined in this study, dentine restored with glass-ionomer cement showed higher microhardness values (p < 0.0001). It may be concluded that the glass-ionomer cement decreases the progression of root dentine erosion at restoration margin. (C) 2010 Wiley Periodicals, Inc J Biomed Mater Res Part B Appl Biomater 93B 304-305, 2010

Influence of NaHCO(3) Powder on Translucency of Microfilled Composite Resin Immersed in Different Mouthrinses

The regular use of mouthrinses, particularly when combined with the use of air-powder polishing, could affect the appearance of tooth-colored restorations. The current study sought to evaluate the effect of NaHCO(3) powder on translucency of a microfilled composite resin immersed in different mouthrinses, at distinct evaluation periods. Eighty disk-shaped specimens of composite resin (Durafill VS, Heraeus Kulzer GmbH & Co. KG, Hanau, Germany) were prepared. The composite specimens were then randomly allocated into two groups according to the surface treatment: exposure to NaHCO(3) powder (10 seconds) or nonexposure, and they were randomly assigned into four subgroups, according to the mouthrinses employed (N = 10): Periogard (Colgate/Palmolive, Sao Bernardo do Campo, SP, Brazil), Cepacol (Aventis Pharma, Sao Paulo, SP, Brazil), Plax (Colgate/Palmolive), and distilled water (control group). The samples were immersed for 2 minutes daily, 5 days per week, over a 4-month test period. Translucency was measured with a transmission densitometer at seven evaluation periods. Statistical analyses (analysis of variance and Tukey`s test) revealed that: distilled water presented higher translucency values (86.72%); Periogard demonstrated the lowest translucency values (72.70%); and Plax (74.05%) and Cepacol (73.32%) showed intermediate translucency values, which were statistically similar between them (p > 0.01). NaHCO(3) air-powder polishing increased the changes in translucency associated with the mouthrinses. Air-powder polishing alone had no effect on material translucency. Translucency percent was gradually decreased from 1 week of immersion up to 4 months. It may be concluded that the NaHCO(3) powder and the tested mouthrinses have affected the translucency of microfilled composite resin, according to the tested time. CLINICAL SIGNIFICANCE During the last decade, the demand for composite resin restorations has grown considerably, however, controversy persists regarding the effect of surface roughness on color stability.

The Usefulness of Caries Frequency, Depth, and Location in Determining Cariogenicity and Past Subsistence: A Test on Early and Later Agriculturalists From the Peruvian Coast

Dental markers have been used to unravel particularities of paleodiet, subsistence, social structure, and health. This article aims to compare oral pathology among four pre-Columbian groups with different degrees of agricultural and socio-cultural development but comparable ecological conditions who lived on the coastal desert of Peru. Three of these groups are assigned to distinct phases of the Formative Period (2500-1 BC), a time critical for our understanding of the development of agriculture and social complexity. The fourth group corresponds to the Late Intermediate Period (1000-1470 AD), when agriculture had its apogee and society was highly stratified. In this study we test whether there is an increase (1) in the frequency of carious lesions and (2) in caries depth, and (3) if there is a shift from occlusal to extra-occlusal caries locations with the development of agriculture. Therefore, we analyze the frequencies of carious lesions and antemortem tooth loss (AMTL), the caries distributions by age, sex, and type of tooth, as well as the tissues affected by, and the location of the carious lesions. Since there are no significant differences in the frequencies of carious lesions and AMTL between the groups, we reject hypothesis 1. In contrast, caries depth does increase, and caries location changes from occlusal to extra-occlusal sites with agricultural development. However, we can only corroborate hypothesis 2 and 3 when taking into consideration dental wear. Thus, we recommend that caries depth and locations should be used with evaluations of dental wear to reconstruct subsistence in ancient populations. Am J Phys Anthropol 143:75-91, 2010. (C) 2010 Wiley-Liss, Inc.

Twenty Years of Acanthamoeba Keratitis

Purpose: We described the rate of Acanthamoeba keratitis (AK) in a referral eye center in Sao Paulo, Brazil, through a retrospective review of clinical and laboratorial records of patients over 2 decades. Methods: From 1987 to 2006, a total of 581 requests for amoebic laboratory workup in cases of infections keratitis were investigated. Statistical analyses were applied to analyze a tendency of AK cases. Results: Acanthamoeba species were cultured from corneal scrapings of 185 patients, 5 of them with bilateral infection. Eighty-three percent of those patients were related with contact lens wear. Conclusions: The results suggested that patients with AK have persisted and increased over time at our ophthalmology center. Contact lenses showed to be a potential risk factor. Amoebic corneal infection can be considered as a new but well-established disease ill Brazilian ophthalmology and visual sciences.

Bone growth around silicon nitride implants - An evaluation by scanning electron microscopy

Silicon nitride has demonstrated to be a potential candidate for clinical applications because it is a non-cytotoxic material and has satisfactory fracture toughness, high wear resistance and low friction coefficient. In this paper, samples of silicon nitride, which were kept into rabbits` tibias for 8 weeks, and the adjacentbone tissue were analysed by scanning electron microscopy in order to verify the bone growth around the implants and the interaction between the implant and the bone. Bone growth occurred mainly in the cortical areas, although it has been observed that the newly bone tends to grow toward the marrow cavity. Differences were observed between the implants installed into distal and proximal regions. In the first region, where the distance between the implant and the cortical bone is greater than in the proximal region, the osteoconduction process was evidenced by the presence of a bridge bone formation toward the implant surface. The results showed that silicon nitride can be used as biomaterial since the newly bone grew around the implants. (c) 2007 Elsevier Inc. All rights reserved.

Infant mortality model for lifetime data

In this paper we introduce a parametric model for handling lifetime data where an early lifetime can be related to the infant-mortality failure or to the wear processes but we do not know which risk is responsible for the failure. The maximum likelihood approach and the sampling-based approach are used to get the inferences of interest. Some special cases of the proposed model are studied via Monte Carlo methods for size and power of hypothesis tests. To illustrate the proposed methodology, we introduce an example consisting of a real data set.

Application of solid sampling device for direct determination of chromium and nickel in lubricating oils by graphite furnace atomic absorption spectrometry

One method using a solid sampling device for the direct determination of Cr and Ni in fresh and used lubricating oils by graphite furnace atomic absorption spectrometry are proposed. The high organic content in the samples was minimized using a digestion step at 400 degrees C in combination with an oxidant mixture 1.0% (v v(-1)) HNO3+15% (v v(-1)) H2O2+0.1% (m v(-1)) Triton X-100 for the in situ digestion. The 3-field mode Zeeman-effect allowed the spectrometer calibration up to 5 ng of Cr and Ni. The quantification limits were 0.86 mu g g(-1) for Cr and 0.82 mg g(-1) for Ni, respectively. The analysis of reference materials showed no statistically significant difference between the recommended values and those obtained by the proposed methods.

Effect of Calcium Pre-rinse and Fluoride Dentifrice on Enamel and on Dental Plaque Formed In Situ

Purpose: The aim of this in situ double-blind randomised crossover study was to investigate the effect of calcium (Ca) pre-rinse on the composition of plaque and on enamel prior to the use of fluoride (F) dentifrice. Materials and Methods: During four phases (14 days each) of this study, 10 volunteers had agreed to wear dental appliances containing two healthy bovine enamel blocks. A fresh solution containing 20% weight/volume (w/v) sucrose was dripped on the enamel blocks ex vivo for 5 min three times a day. Subsequently, the appliances were replaced in the mouth, and the volunteers rinsed their mouth with 10 mL of a Ca (150 mmol/L) or a placebo rinse (1 min). In sequence, a slurry (1:3 w/v) of F (1030 ppm) or placebo dentifrice was dripped onto the blocks ex vivo for 1 min. During this time, the volunteers brushed their teeth with the respective dentifrice. The appliances were replaced in the mouth, and the volunteers rinsed their mouth with water. The plaque formed on the blocks was analysed for F and Ca. The enamel demineralisation as well as the incorporation of F on enamel was evaluated by cross-sectional microhardness and alkali-soluble F analysis, respectively. Data were tested using analysis of variance (P < 0.05). Results: The Ca pre-rinse prior to the use of the F dentifrice led to a three- and sixfold increase in the plaque F and Ca concentrations, respectively. It also did not have any additive effect on the F content on the enamel and the demineralisation of the enamel, in comparison with the use of F dentifrice alone. Conclusions: A Ca lactate rinse used prior to the F dentifrice was able to change the mineral content in the plaque, but it was unable to prevent enamel demineralisation.

Tribological Testing of Some Potential PVD and CVD Coatings for Steel Wire Drawing Dies

Cemented carbide is today the most frequently used drawing die material in steel wire drawing applications. This is mainly due to the possibility to obtain a broad combination of hardness and toughness thus meeting the requirements concerning strength, crack resistance and wear resistance set by the wire drawing process. However, the increasing cost of cemented carbide in combination with the possibility to increase the wear resistance of steel through the deposition of wear resistant CVD and PVD coatings have enhanced the interest to replace cemented carbide drawing dies with CVD and PVD coated steel wire drawing dies. In the present study, the possibility to replace cemented carbide wire drawing dies with CVD and PVD coated steel drawing dies have been investigated by tribological characterisation, i.e. pin-on-disc and scratch testing, in combination with post-test observations of the tribo surfaces using scanning electron microscopy, energy dispersive X-ray spectroscopy and 3D surface profilometry. Based on the results obtained, CVD and PVD coatings aimed to provide improved tribological performance of steel wire drawing dies should display a smooth surface topography, a high wear resistance, a high fracture toughness (i.e. a high cracking and chipping resistance) and intrinsic low friction properties in contact with the wire material. Also, the steel substrate used must display a sufficient load carrying capacity and resistance to thermal softening. Of the CVD and PVD coatings evaluated in the tribological tests, a CVD TiC and a PVD CrC/C coating displayed the most promising results.

A study of slag corrosion of oxides and oxide-carbon refractories during steel refining

The use of ceramic material as refractories in the manufacturing industry is a common practice worldwide. During usage, for example in the production of steel, these materials do experience severe working conditions including high temperatures, low pressures and corrosive environments. This results in lowered service lives and high consumptions of these materials. This, in turn, affects the productivity of the whole steel plant and thereby the cost. In order to investigate how the service life can be improved, studies have been carried out for refractories used in the inner lining of the steel ladles. More specifically, from the slag zone, where the corrosion is most severe. By combining thermodynamic simulations, plant trails and post-mortem studies of the refractories after service, vital information about the behaviour of the slagline refractories during steel refining and the causes of the accelerated wear in this ladle area has been achieved. The results from these studies show that the wear of the slagline refractories of the ladle is initiated at the preheating station, through reduction-oxidation reactions. The degree of the decarburization process is mostly dependent on the preheating fuel or the environment. For refractories without antioxidants, refractory decarburization is slower when coal gas is used in ladle preheating than when a mixture of oil and air is used. In addition, ladle preheating of the refractories without antioxidants leads to direct wear of the slagline refractories. This is due to the total loss of the matrix strength, which results in a sand-like product. Thermal chemical changes that take place in the slagline refractories are due to the MgO-C reaction as well as the formation of liquid phases from impurity oxides. In addition, the decrease in the system pressure during steel refining makes the MgO-C reaction take place at the steel refining temperatures. This reduces the refractory’s resistance to corrosion. This is a serious problem for both the magnesia-carbon and dolomite-carbon refractories. The studies of the reactions between the slagline refractories and the different slag compositions showed that slags rich in iron oxide lead mostly to the oxidation of carbon/graphite in the carbon-containing refractories. This leads to an increased porosity and wettability and therefore an enhanced penetration of slag into the refractory structure. If the slag contains high contents of alumina and or silica (such as the steel refining slag), reactions between the slag components and the dolomite-carbon refractory are promoted. This leads to the formation of low-temperature melting phases such as calcium-aluminates and silicates. The state of these reaction products during steel refining leads to an accelerated wear of the dolomite-carbon refractory. The main products of the reactions between the magnesia-carbon refractory and the steel refining slag are MgAl2O4 spinels, and calcium-aluminates, and silicates. Due to the good refractory properties of MgAl2O4 spinels, the slag corrosion resistance of the magnesiacarbon refractory is promoted.

Mechanical and tribological properties of PVD-coated cemented carbide as evaluated by a new multi-pass scratch testing method

A new test method based on multipass scratch testing has been developed for evaluating the mechanical and tribological properties of thin, hard coatings. The proposed test method uses a pin-on-disc tribometer and during testing a Rockwell C diamond stylus is used as the “pin” and loaded against the rotating coated sample. The influence of normal load on the number of cycles to coating damage is investigated and the resulting coating damage mechanisms are evaluated by posttest scanning electron microscopy. The present study presents the test method by evaluating the performance of Ti0.86Si0.14N, Ti0.34Al0.66N, and (Al0.7Cr0.3)2O3 coatings deposited by cathodic arc evaporation on cemented carbide inserts. The results show that the test method is quick, simple, and reproducible and can preferably be used to obtain relevant data concerning the fatigue, wear, chipping, and spalling characteristics of different coating-substrate composites. The test method can be used as a virtually nondestructive test and, for example, be used to evaluate the fatigue and wear resistance as well as the cohesive and adhesive interfacial strength of coated cemented carbide inserts prior to cutting tests.

How initial vocational education and training (IVET) teachers in Sweden perceive their prospects of being able to prepare upper secondary school pupils for a future occupation

Vocational teachers in Swedish upper secondary schools are a heterogeneous category of teachers, connected to different types of trade. These teachers represent a broad set of trade skills varying in content and character. In their teacher role, they continue to wear the clothes, speak the language, share the culture and remain mentally in their former professions. Still, it is central that they keep up this contact to be able to school the pupils into the environment of the trade in question, but also to help them to understand what skills a profession demands. However, the individual teacher also has to distance himself from the negative elements in the culture of the profession: patterns and habits that, for various reasons, have to be broken or changed. This paper draws attention to the ways in which a group of vocational teachers, who were participants in a project that aimed to train unauthorized vocational teachers, expressed their ambitions to prepare the pupils for a future professional career. When collecting information, we used the degree dissertations they produced and discussed in seminars, and informal dialogues. The result shows that it is important that the instruction location resembles a real working site as far as possible. These places are more or less realistic copies of a garage, a restaurant kitchen, a hairdressing salon, and so on, in order to give the pupils a realistic setting for instruction. However, the fact that these simulated workplaces lack the necessary support functions that exist in a company creates problems, problems which make a lot of extra work for the teachers. Vocational teachers also have to instruct the pupil in the experienced practitioner’s professional skills and working situation, but the pupil herself/himself must learn the job by doing it in practice. Some vocational upper secondary programs lack relevant course literature and the businesses give little support. This also makes extra work for the teachers. Moreover, the distance between the vocational programs and the trainee jobs was experienced as being difficult to overcome. One reason seems to be differences between businesses and differing preconditions between small and big companies’ abilities to take care of these pupils. The upper secondary school vocational programs also play a role in cementing existing gender roles, as well as perpetuating class-related patterns on the labour market.

How initial vocational education and training (IVET) teachers in Sweden perceive their prospects of being able to prepare upper secondary school pupils for a future occupation

Vocational teachers in Swedish upper secondary schools are a heterogeneous category of teachers, connected to different types of trade. These teachers represent a broad set of trade skills varying in content and character. In their teacher role, they continue to wear the clothes, speak the language, share the culture and remain mentally in their former professions. Still, it is central that they keep up this contact to be able to school the pupils into the environment of the trade in question, but also to help them to understand what skills a profession demands. However, the individual teacher also has to distance himself from the negative elements in the culture of the profession: patterns and habits that, for various reasons, have to be broken or changed. This paper draws attention to the ways in which a group of vocational teachers, who were participants in a project that aimed to train unauthorized vocational teachers, expressed their ambitions to prepare the pupils for a future professional career. When collecting information, we used the degree dissertations they produced and discussed in seminars, and informal dialogues. The result shows that it is important that the instruction location resembles a real working site as far as possible. These places are more or less realistic copies of a garage, a restaurant kitchen, a hairdressing salon, and so on, in order to give the pupils a realistic setting for instruction. However, the fact that these simulated workplaces lack the necessary support functions that exist in a company creates problems, problems which make a lot of extra work for the teachers. Vocational teachers also have to instruct the pupil in the experienced practitioner’s professional skills and working situation, but the pupil herself/himself must learn the job by doing it in practice. Some vocational upper secondary programs lack relevant course literature and the businesses give little support. This also makes extra work for the teachers. Moreover, the distance between the vocational programs and the trainee jobs was experienced as being difficult to overcome. One reason seems to be differences between businesses and differing preconditions between small and big companies’ abilities to take care of these pupils. The upper secondary school vocational programs also play a role in cementing existing gender roles, as well as perpetuating class-related patterns on the labour market.

Privatização da Vale do Rio Doce: valores, manifestações e implicações

Este estudo investigou, na Companhia Vale do Rio Doce (CVRD), como os funcionários perceberam as mudanças ocorridas na empresa, as ações da alta administração e o que ocorreu com os valores na organização após o processo de privatização. O objetivo final da pesquisa foi verificar que valores norteiam as propostas administrativas da Vale após a privatização, e como se manifestam nas ações e na postura dos agentes na sede da empresa. O referencial teórico incluiu mudança organizacional, teoria dos valores e responsabilidade das ações administrativas, para compreender o contexto atual da empresa após a privatização. A pesquisa de campo foi concebida sob o paradigma do construtivismo, em busca de percepções e sentimentos subjacentes e manifestos em entrevistas e questionários a fim de explicitar os valores passados e presentes na organização e possibilidades de uma nova realidade. Uma abordagem fenomenológica complementar favoreceu a inserção da autora no mundo da vida dessa organização, facilitando a fluência do diálogo para a apreensão de manifestações e implicações dos valores das pessoas no processo de transição. As reflexões finais indicam a necessidade de um trabalho organizacional que envolva funcionários e alta administração com o propósito comum de redescoberta do significado próprio da organização. O Programa Vale Viver surge como uma tentativa nessa direção. Os valores "vestir a camisa", "valorizar a prata da casa" e "vencer desafios" acompanham o tempo de vida da cultura da Vale. O valor "vestir a camisa," cujo significado é compartilhamento autêntico, na atualidade é mais uma expectativa a ser retomada do que uma vivência. O valor "vencer desafios" está mais presente na área operacional e o valor "valorizar a prata da casa" aparece mais relacionado a programas como o Banco de OpOliunidades, reavivado pelo Vale Viver. Não significa que o Vale Viver seja a única saída para a retomada da confiança, da elevação da auto-estima e de uma articulação empregados e nova administração na construção de uma base comum de valores, mas é a possibilidade mais visível no momento em que a retomada do espírito da V ALE é fundamental para essa nova etapa de sua vida.

Consumo para obtenção de status: estudo empírico entre meninas pré-dolescentes de São Luis do Maranhão

The consumption of goods from brands in vogue, which symbolize status, popularity, success and social distinction, among those from the same social group in a pre-teenage girls¿ environment, has been a topic for academic studies as well as the market, due to their relevant consumption power for the companies worldwide. This paper aims to check out the use of these goods by them in São Luís, in order to become popular, succesful and socially distinguished; and the relation of the consumption for status with the brand image consumed and the pre-teenage girl self image; how familiar with the goods and the brand they are; and their attitude concerning their qualities. The empirical metodology had two phases: a qualitative and a quantitative one. The first one started with a specific group of 8 (eight) pre-teenage girls from high and medium classes, with the purpose of collecting some basis in order to reinforce the theory once the hypothesis were elaborated and used to guide the quantitative research as well as to adapt some North American scales. In the second stage of the qualitative research, a survey was applied in a convenience sample of 300 (three hundred) pre-teenage girls from São Luís, all from the high, medium high and low classes. The main result showed the pre-teenage girls from São Luís consume goods and brands for status, so they could get prestige, success, and social distinction, however, they do not define themselves or judge the social status of those from their social group based only on the clothes they wear and the brands which indicate their consumption power. Some other status symbols are important too, like, housing, the family car, the neighborhood where they dwell, the parents¿ occupation; the school they go to, the long and straight hair, how correct they speak Portuguese and their holiday trips. Another result highlighted was the strong relation of the brand image with their self image in the consumption for status.