Determination of Minoxidil by Bleaching the Permanganate Carrier Solution in a Flow-Based Spectrophotometric System

The determination of minoxidil (MX) with potassium permanganate as a carrier in a flow injection method is described. The detection at 550nm was linear from 1.0x10-5 to 5.0x10-4mol L-1. The limit of detection (3 sigma/slope) was 8.92x10-6mol L-1, with an analytical frequency of 32h-1. The proposed method was applied to commercial samples, with recoveries from 104.7 to 106.4%. Comparison with the HPLC procedure reveled relative errors from 0.48 to 1.4%, and the results agreed within a 95% confidence level.

Removal of Zn(2+) from Electroplating Wastewater Using Modified Wood Sawdust and Sugarcane Bagasse

This paper describes the preparation of new adsorbents derived from sugarcane bagasse and wood sawdust (Manilkara sp.) to remove zinc (II) ions from electroplating wastewater. The first part deals with the chemical modification of sugarcane bagasse and wood sawdust, using succinic anhydride to introduce carboxylic acid functions into the material. The obtained materials (modified sugarcane bagasse MB2 and modified wood sawdust MS2) were then characterized by infrared spectroscopy (IR) and used in adsorption experiments. The adsorption experiments evaluates Zn(2+) removal from aqueous single metal solution and real electroplating wastewater on both batch and continuous experiments using fixed-bed columns prepared in laboratorial scale with the obtained adsorbents. Adsorption isotherms were then developed using Langmuir model and the Thomas kinetic model. The calculated Zn(2+) adsorption capacities were found to be 145 mg/g for MS2 and 125 mg/g for MB2 in single metal aqueous solution, whereas for the industrial wastewater these values were 61 mg/g for MS2 and 55 mg/g for MB2.

Load balancing solution and evaluation of F5 content switch equipment

The Thesis focused on hardware based Load balancing solution of web traffic through a load balancer F5 content switch. In this project, the implemented scenario for distributing HTTPtraffic load is based on different CPU usages (processing speed) of multiple member servers.Two widely used load balancing algorithms Round Robin (RR) and Ratio model (weighted Round Robin) are implemented through F5 load balancer. For evaluating the performance of F5 content switch, some experimental tests has been taken on implemented scenarios using RR and Ratio model load balancing algorithms. The performance is examined in terms of throughput (bits/sec) and Response time of member servers in a load balancing pool. From these experiments we have observed that Ratio Model load balancing algorithm is most suitable in the environment of load balancing servers with different CPU usages as it allows assigning the weight according to CPU usage both in static and dynamic load balancing of servers.

A stopping rule while searching for optimal solution of facility-location

Solutions to combinatorial optimization, such as p-median problems of locating facilities, frequently rely on heuristics to minimize the objective function. The minimum is sought iteratively and a criterion is needed to decide when the procedure (almost) attains it. However, pre-setting the number of iterations dominates in OR applications, which implies that the quality of the solution cannot be ascertained. A small branch of the literature suggests using statistical principles to estimate the minimum and use the estimate for either stopping or evaluating the quality of the solution. In this paper we use test-problems taken from Baesley's OR-library and apply Simulated Annealing on these p-median problems. We do this for the purpose of comparing suggested methods of minimum estimation and, eventually, provide a recommendation for practioners. An illustration ends the paper being a problem of locating some 70 distribution centers of the Swedish Post in a region.

Network density and the p-median solution

The p-medianmodel is commonly used to find optimal locations of facilities for geographically distributed demands. So far, there are few studies that have considered the importance of the road network in the model. However, Han, Håkansson, and Rebreyend (2013) examined the solutions of the p-median model with densities of the road network varying from 500 to 70,000 nodes. They found as the density went beyond some 10,000 nodes, solutions have no further improvements but gradually worsen. The aim of this study is to check their findings by using an alternative heuristic being vertex substitution, as a complement to their using simulated annealing. We reject the findings in Han et al (2013). The solutions do not further improve as the nodes exceed 10,000, but neither do the solutions deteriorate.

A contractive method for computing the stationary solution of the euler equation

A contractive method for computing stationary solutions of intertemporal equilibrium models is provide. The method is is implemented using a contraction mapping derived from the first-order conditions. The deterministic dynamic programming problem is used to illustrate the method. Some numerical examples are performed.

Inexpensive solution for real-time video and image stitching

Image stitching is the process of joining several images to obtain a bigger view of a scene. It is used, for example, in tourism to transmit to the viewer the sensation of being in another place. I am presenting an inexpensive solution for automatic real time video and image stitching with two web cameras as the video/image sources. The proposed solution relies on the usage of several markers in the scene as reference points for the stitching algorithm. The implemented algorithm is divided in four main steps, the marker detection, camera pose determination (in reference to the markers), video/image size and 3d transformation, and image translation. Wii remote controllers are used to support several steps in the process. The built‐in IR camera provides clean marker detection, which facilitates the camera pose determination. The only restriction in the algorithm is that markers have to be in the field of view when capturing the scene. Several tests where made to evaluate the final algorithm. The algorithm is able to perform video stitching with a frame rate between 8 and 13 fps. The joining of the two videos/images is good with minor misalignments in objects at the same depth of the marker,misalignments in the background and foreground are bigger. The capture process is simple enough so anyone can perform a stitching with a very short explanation. Although real‐time video stitching can be achieved by this affordable approach, there are few shortcomings in current version. For example, contrast inconsistency along the stitching line could be reduced by applying a color correction algorithm to every source videos. In addition, the misalignments in stitched images due to camera lens distortion could be eased by optical correction algorithm. The work was developed in Apple’s Quartz Composer, a visual programming environment. A library of extended functions was developed using Xcode tools also from Apple.

Comparative study between the effects of hyaluronic acid and acid galactan purified from eggs of the mollusk Pomacea sp in wound healing

To compare the effect of hyaluronic acid (HA) and of AG on the healing of intestine wounds. Methods: The semi-purified extract of the eggs of the mollusc was obtained by fractionation with ammonium sulfate and purification for ion-exchange chromatography. The obtained galactans were eluted in water (neutral galactan) and in 0.1 and 0.2M NaCl (acidic galactans). The in vivo study was performed with 45 “Wistar” rats, separated in three groups (n=15). Solutions containing HA 1%, GA 1% or saline solution 0,9%, was placed topically on the sutures of wounds in the small intestine of the rats. After 05, 10 and 21 days the animals were sacrificed and biopsy of the healing tissue was done. Results: The hystologic grading was more significant for HA and AG groups when compared to the group C. AG stimulated the appearance of macrophages, giant cells and increase in the concentration of collagen in the area of the wound when compared to HA. Conclusion: The topical use of GA in intestinal wounds promoted the anticipation of events that are important in the wound healing

CERAMIC MATERIAL FROM SEWAGE SLUDGE AS SUPPORT MATERIAL SUPPLY WATER FILTRATION

This study shows a possibility of using municipal sewage sludge after thermal treatment in the production of a filtering material to water treatment. Due to the fast urbanization and implementation of high standards for effluent in many countries in recent years, the sewage sludge is being produced in an ever increasing amount. Therefore, the use of sludge is a suitable solution for the expected large quantity of sludge. Dehydration of sludge was performed by controlled heating at temperatures of 1100 degrees C, 850 degrees C, 650 degrees C, 350 degrees C for 3 hours. After thermal treatment the sludge was characterized by X-ray fluorescence, TG/DTG/DTA, residue solubilization and residue lixiviation tests. The aim of the present work was to observe, thought the characterization techniques, if the treated sewage sludge is or not adequate to be used as filter material to water treatment. It will be verified which treatment temperature of the sludge offer possibility to its use in water treatment without carrying pollutants in concentrations out of the standards.

COMBUSTION and PYROLYSIS of A SLUDGE FROM WASTEWATER TREATMENT PLANT

The possibility of thermal treatment plants of municipal wastewater is an alternative solution for the final disposition of the sludge produced on small cities as Barueri, a small town of São Paulo State, Brazil. Combustion and pyrolysis of that municipal waste, occurring respectively in air and nitrogen, have been studied by thermogravimetry (TG) and differential thermal analysis (DTA). The main steps of each case were analyzed and Kissinger plots were used to estimate respective activation energies. DTG peaks are more indicated to represent the condition of maximum reaction rates than DTA peaks.

Renal and vascular effects of the natriuretic peptide isolated from Crotalus durissus cascavella venom

Crotalus durissus cascavella is a snake that is usually found in the scrublands of northeast Brazil. The components of its venom may have effects on the vascular and renal systems. Recently, a new bradykinin inhibitory peptide has been identified in the venom of the Crotalinae family. The aim of the present study was to investigate the renal and vascular effects of the natriuretic peptide isolated from the venom of Crotalus durissus cascavella (NP2_Casca). The chromatographic profile showed the fractionation of substances identified as convulxin, gyroxin, crotoxin and crotamine, as well as fractions V and VI. The electrophoretic profile of fraction V consisted of several bands ranging from approximately 6 kDa to 13 kDa, while fraction VI showed only two main electrophoretic bands with molecular weights of approximately 6 and 14 kDa. Reverse-phase chromatography showed that NP2_Casca corresponds to about 18% of fraction VI and that this fraction is the main natriuretic peptide. NP2_Casca was compared to other natriuretic peptides from other sources of snake venom. All amino acid sequences that were compared showed a consensus region of XGCFGX, XLDRIX and XSGLGCX. The group treated with NP2-Casca showed an increase in perfusion pressure, renal vascular resistance, urinary flow and glomerular filtration rate. The percent of total and proximal tubular transport of sodium was reduced significantly after administration of the peptide. The mean arterial pressure showed a dose-dependent decrease after infusion of NP2_Casca, and an increase in nitrite production. In the aortic ring assay, NP2_Casca caused a relaxant effect in endothelium-intact thoracic aortic rings precontracted with phenylephrine in the presence and absence of isatin. NP2_Casca failed to relax the aortic rings precontracted with an isosmotic potassium Krebs-Henseleit solution. In conclusion, the natriuretic peptide isolated from Crotalus durissus cascavella venom produced renal and vascular effects. NP2_Casca reduced total and proximal sodium tubular transport, leading to an increase in sodium excretion, thereby demonstrating a diuretic action. A hypotensive effect was displayed in an arterial pressure assay, with an increase in nitrite production, suggesting a possible vasoactive action. (C) 2008 Elsevier Ltd. All rights reserved.

Rhamnolipid produced from agroindustrial wastes enhances hydrocarbon biodegradation in contaminated soil

A crude biosurfactant solution was produced by Pseudomonas aeruginosa growing on agroindustrial wastes as the substrate and used to study its effect on hydrocarbon biodegradation by the indigenous soil microflora under laboratory conditions. Two concentrations were studied at first and 1 mg of biosurfactant/g of soil showed to be the most efficient for the total petroleum hydrocarbon reduction, which reached 85% at the first 20 days in soil microcosms. Respirometric and microbial analyses showed that the biosurfactant added did not have toxic effects over the microbial population. The use of a biosurfactant for bioremediation has been limited because of its high cost production. Biosurfactants produced from cost-free by-products combines waste minimization with economic potential bioremediation process.

Anthelmintic efficacy of oral trichlorfon solution against ivermectin resistant nematode strains in cattle

Infected calves from two different rural estates in Brazil were studied to assess the anthelmintic efficacy of oral trichlorfon against naturally occurring ivermectin resistant parasitic nematode strains. In experiment 1, infected animals were from a region where ivermectin resistant populations of Haemoncus placei, Cooperia punctata,Cooperia spatulata and Trichuris discolor have recently been identified. Six calves with natural gastrointestinal nematode infections were treated with 48.5 mg/kg aqueous trichlorfon administered orally and six calves acted as a non-treated control group. In experiment 11 24 naturally infected calves were selected to enter one of four treatment groups, six animals each received: 48.5 mg/kg oral trichlorfon; 200 mu g/kg subcutaneous 1% ivermectin; 630 mu g/kg subcutaneous 3.15% ivermectin; or no treatment (control group). Gastrointestinal helminths were counted and identified post-mortem at 7 days (trichlorfon and 1% ivermectin treated and untreated animals) or 14 days (3.15% ivermectin treated and untreated animals) after administration of the test agents. Experiment I identified a high level efficacy for oral trichlorfon against four helminth species that have previously been shown to be ivermectin resistant in this geographical region: percentage efficacy was 99.82% against adult H. placei, 99.18% against C. punctata, 99.33% against C. spatulata, 81.06% against T. axei, 98.46% against Oesophagostomum radiatum and 100% against T. discolor. Trichlorfon also showed activity against the ivermectin (1% and 3.15%) resistant helminth species identified in experiment 11, attaining efficacy levels of 99.17% against H. placei, 98.46% against C punctata and 100.00% against T. discolor. These findings indicate that oral trichlorfon is an effective treatment option in the management of cattle infected with ivermectin resistant helminths. (C) 2009 Elsevier B.V. All rights reserved.

Effect of steeping conditions (sulfur dioxide, lactic acid, and temperature) on starch yield, starch quality, and germ quality from the Intermittent Milling and Dynamic Steeping process (IMDS) for a Brazilian corn hybrid

Effect of lactic acid, SO2, temperature, and their interactions were assessed on the dynamic steeping of a Brazilian dent corn (hybrid XL 606) to determine the ideal relationship among these variables to improve the wet-milling process for starch and corn by-products production. A 2x2x3 factorial experimental design was used with SO2 levels of 0.05 and 0.1% (w/v), lactic acid levels of 0 and 0.5% (v/v), and temperatures of 52, 60, and 68degreesC. Starch yield was used as deciding factor to choose the best treatment. Lactic acid added in the steep solution improved the starch yield by an average of 5.6 percentage points. SO2 was more available to break down the structural protein network at 0.1% than at the 0.05% level. Starch-gluten separation was difficult at 68degreesC. The lactic acid and SO2 concentrations and steeping temperatures for better starch recovery were 0.5, 0.1, and 52degreesC, respectively. The Intermittent Milling and Dynamic Steeping (IMDS) process produced, on average, 1.4% more starch than the conventional 36- hr steeping process. Protein in starch, oil content in germ, and germ damage were used as quality factors. Total steep time can be reduced from 36 hr for conventional wet-milling to 8 hr for the IMDS process.

Haematological and gill responses in parasitized tilapia from valley of Tijucas River, SC, Brazil

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)