A new method for continuous quality control of nsm cfrp systems

In the last decade the near-surface mounted (NSM) strengthening technique using carbon fibre reinforced polymers (CFRP) has been increasingly used to improve the load carrying capacity of concrete members. Compared to externally bonded reinforcement (EBR), the NSM system presents considerable advantages. This technique consists in the insertion of carbon fibre reinforced polymer laminate strips into pre-cut slits opened in the concrete cover of the elements to be strengthened. CFRP reinforcement is bonded to concrete with an appropriate groove filler, typically epoxy adhesive or cement grout. Up to now, research efforts have been mainly focused on several structural aspects, such as: bond behaviour, flexural and/or shear strengthening effectiveness, and energy dissipation capacity of beam-column joints. In such research works, as well as in field applications, the most widespread adhesives that are used to bond reinforcements to concrete are epoxy resins. It is largely accepted that the performance of the whole application of NSM systems strongly depends on the mechanical properties of the epoxy resins, for which proper curing conditions must be assured. Therefore, the existence of non-destructive methods that allow monitoring the curing process of epoxy resins in the NSM CFRP system is desirable, in view of obtaining continuous information that can provide indication in regard to the effectiveness of curing and the expectable bond behaviour of CFRP/adhesive/concrete systems. The experimental research was developed at the Laboratory of the Structural Division of the Civil Engineering Department of the University of Minho in Guimar\~aes, Portugal (LEST). The main objective was to develop and propose a new method for continuous quality control of the curing of epoxy resins applied in NSM CFRP strengthening systems. This objective is pursued through the adaptation of an existing technique, termed EMM-ARM (Elasticity Modulus Monitoring through Ambient Response Method) that has been developed for monitoring the early stiffness evolution of cement-based materials. The experimental program was composed of two parts: (i) direct pull-out tests on concrete specimens strengthened with NSM CFRP laminate strips were conducted to assess the evolution of bond behaviour between CFRP and concrete since early ages; and, (ii) EMM-ARM tests were carried out for monitoring the progressive stiffness development of the structural adhesive used in CFRP applications. In order to verify the capability of the proposed method for evaluating the elastic modulus of the epoxy, static E-Modulus was determined through tension tests. The results of the two series of tests were then combined and compared to evaluate the possibility of implementation of a new method for the continuous monitoring and quality control of NSM CFRP applications.

Modulare Synthese von Sialyl-Lewis X-Mimetika als Selektin-Liganden

Zelladhäsions- und Zellerkennungsphänomene spielen eine entscheidende Rolle im biologischen Geschehen: So findet die Kommunikation zwischen Zellen zu einem großen Teil zwischen membranständigen Adhäsionsmolekülen und ebenfalls membranständigen Liganden auf Nachbarzellen statt. Zu diesen Adhäsionsmolekülen gehören die Selektine, die von fundamentaler Bedeutung für die Bekämpfung von Entzündungskrankheiten und damit für die Funktionsweise unseres Immunsystems sind. Tritt eine Entzündung in unserem Körper auf, so sind Selektine an Adhäsionsprozessen beteiligt, die zur Auswanderung von Leukozyten aus dem Blutstrom in das entzündete Gewebe führen. Diese auswandernden Zellen enthalten eine Vielzahl von Wirkstoffen, die Krankheitserreger bekämpfen, aber auch körpereigenes Gewebe angreifen können. Viele Krankheitsbilder, die mit akut oder chronisch entzündlichen Prozessen einhergehen, hängen mit einer Dysregulation der Selektine zusammen. In diesen Fällen werden übermäßig Selektine exprimiert und es kommt zu einer lokal überschießenden Akkumulation von Leukozyten, die zu Schädigungen von gesundem Gewebe führen kann. rnZu diesen Krankheiten gehören z.B. die rheumatoide Arthritis, die myocardialen Ischämie, Psoriasis sowie Asthma und Allergien. Auch bei der Abstoßung von Transplantaten und Tumormetastasierung wurde eine Beteiligung der Selektine nachgewiesen. Eine Strategie gegen diese unerwünschten Effekte ist die selektive Inhibierung der Selektine, welche aufgrund der bedeutenden Rolle der Selektine in der Genese zahlreicher Krankheiten, von großem pharmazeutischen Interesse ist. rnIn der vorliegenden Arbeit ist die Entwicklung chemischer Synthesen von Verbindungen beschrieben, welche selektininhibierende Eigenschaften aufweisen sollen. Solche sog. Mimetika, die wie die natürlichen Liganden mit den Selektinen wechselwirken, sind nicht nur potenzielle Medikamente, sondern können auch durch veränderte Affinität zur Aufklärung von selektinvermittelten Zelladhäsionsprozessen dienen.rn

Advanced polymeric materials for applications in technical equipment for snow sports

The thesis is divided in three chapters, each one covering one topic. Initially, the thermo-mechanical and impact properties of materials used for back protectors have been analysed. Dynamical mechanical analysis (DMTA) has shown that materials used for soft-shell protectors present frequency-sensitive properties. Furthermore, through impact tests, the shock absorbing characteristics of the materials have been investigated proving the differences between soft and hard-shell protectors; moreover it has been demonstrated that the materials used for soft-shell protectors maintain their protective properties after multi-impacts. The second chapter covers the effect of the visco-elastic properties of the thermoplastic polymers on the flexural and rebound behaviours of ski boots. DMTA analysis on the materials and flexural and rebound testing on the boots have been performed. A comparison of the results highlighted a correlation between the visco-elastic properties and the flexural and rebound behaviour of ski boots. The same experimental methods have been used to investigate the influence of the design on the flexural and rebound behaviours. Finally in the third chapter the thermoplastic materials employed for the construction of ski boots soles have been characterized in terms of chemical composition, hardness, crystallinity, surface roughness and coefficient of friction (COF). The results showed a relation between material hardness and grip, in particular softer materials provide more grip with respect to harder materials. On the contrary, the surface roughness has a negative effect on friction because of the decrease in contact area. The measure of grip on inclined wet surfaces showed again a relation between hardness and grip. The performance ranking of the different materials has been the same for the COF and for the slip angle tests, indicating that COF can be used as a parameter for the choice of the optimal material to be used for the soles of ski boots.

Untersuchungen zur autoimmunen Genese der thrombotisch thrombozytopenischen Purpura

Untersuchungen zur autoimmunen Genese der thrombotisch thrombozytopenischen Purpura. rnEinführung: Die idiopathische thrombotisch thrombozytopenische Purpura (TTP) ist eine lebensbedrohliche Mikroangiopathie und wird durch ein Autoantikörper-induziertes Defizit der ADAMTS13-Protease ausgelöst. Eine Assoziation zwischen Krankheitsprädisposition und Vorliegen bestimmter humaner Leukozytenantigene (HLA) wird vermutet. Untersuchungen zu diesem Zusammenhang stellen einen Teil dieser Arbeit dar. rnAutoimmunkrankheiten tendieren zum gemeinsamen Auftreten innerhalb eines Individuums. Im zweiten Teil dieser Arbeit wird untersucht, ob eine solche Kookkurrenz verschiedener Autoimmunkrankheiten auch bei Patienten mit idiopathischer TTP beobachtet werden kann.rnMethodik: Zur Untersuchung der ersten Fragestellung werden die HLA-Klasse I und II-Merkmale von 54 deutschen TTP-Patienten bestimmt. Alle Patienten weisen Autoantikörper gegen ADAMTS13 und eine Protease-Aktivität <5% vor. Die Blutproben werden mittels Sequence Specific Primer-Polymerase Chain Reaction (PCR) und Sequence Specific Oligonucleotid-PCR auf HLA-DRB1, -DRB3-5 und –DQB1 untersucht. Als Referenz dienen die Werte deutscher Knochenmark- und Blutspender, erhalten über www.allelefrequencies.net. Die statistische Auswertung erfolgt mittels zweiseitigem Binomialtest und die resultierenden p-Werte werden nach Benjamini-Hochberg korrigiert.rnZur Beantwortung der zweiten Fragestellung werden 76 deutsche TTP-Patienten anhand eines standardisierten Fragebogens nach Begleiterkrankungen befragt. Als Vergleichswerte dient die Prävalenz der jeweiligen Erkrankung in der Allgemeinbevölkerung. Die statistische Auswertung erfolgt mittels zweiseitigem Binomialtest. Da die p-Werte nicht korrigiert werden, sind die Ergebnisse nur deskriptiv zu verstehen.rnErgebnis: Der Vergleich der HLA-Frequenzen ergibt ein signifikant gehäuftes Vorkommen von HLA-DQB1*02:02 (p<0,001) und -DRB1*11 (p=0,003) innerhalb des Patientenkollektivs. 20% (DQB1*02:02) bzw. 48,1% (DRB1*11) der TTP-Patienten sind im Gegensatz zu nur 1,2% (DQB1*02:02) bzw. 23,5% (DRB1*11) innerhalb der Vergleichsgruppe für das jeweilige HLA-Merkmal positiv.rnDie Befragung der TTP-Patienten bezüglich weiterer Erkrankungen ergab im Vergleich mit der Allgemeinbevölkerung fünf auffällig häufig im Patientenkollektiv vorkommende Autoimmunkrankheiten: Hashimoto Thyreoiditis (23,5% in der Patientengruppe zu 0,7% in der Allgemeinbevölkerung; p<0,001), systemischer Lupus erythematodes (6,5% der Patienten im Gegensatz zu 0,025% in der Allgemeinbevölkerung, p<0,001), Immunthrombozytopenie (6,3% der Patienten zu 0,02% in der Allgemeinbevölkerung; p<0,001), Psoriasis (9,4% der Patienten zu 2,5% in der Allgemeinbevölkerung; p=0,005) und glutensensitive Enteropathie (3,1% der Patienten zu 0,2% in der Allgemeinbevölkerung; p=0,007). rnSchlussfolgerung: Das vermehrte Vorkommen bestimmter HLA-Merkmale im Patientenkollektiv spricht für eine prädisponierende Wirkung dieser Antigene im Krankheitsgeschehen. Eine mögliche HLA-vermittelte Assoziation zwischen TTP und den genannten Autoimmunkrankheiten wird vermutet, kann jedoch nicht in allen Fällen die beobachtete Kookkurrenz ausreichend erklären. Insgesamt bestätigt die vorliegende Arbeit die Assoziation verschiedener Autoimmunkrankheiten untereinander und spricht für eine genetische Prädisposition zur Ausbildung autoimmuner Störungen. rn

Physiologische Konsequenzen eines gestörten Ceramid Stoffwechsels unter Beteiligung von Ceramidsynthase 3 und saurer Ceramidase = Physiological consequences of a disturbed ceramide metabolism due to altered activities of ceramide synthase 3 and acidic ceramidase

Tiefes Wissen über den Ceramid Stoffwechsel ist rudimentär für das Verständnis der Haut-Pathophysiologie (z.B. für atopische Dermatitis oder Psoriasis ) und unabdingbar für gezielte Therapieansätze. Wenn die zwei wichtigen Barriere Funktionen, gegen transepidermalen Wasserverlust und Pathogene Invasionen undicht werden, sind bestimmte Barriere Komponenten wie z.B. Ceramide stark verändert. In Haut und Hoden führt die Deletion der Ceramid-Synthase 3 zu einem Arrest der epidermalen Reifung und der Spermatogenese, welches ihre Bedeutung für eine intakte Barriere heraushebt. Sphingosin (So), ein Abbauprodukt von Cer, wurde als antimikrobielles Mittel identifiziert. So konnte das Wachstum von Candida albicans hemmen und die Invasion von Pathogenen in tiefere Hautschichten verringern, wodurch ihre mögliche Rolle in der Therapie von Hauterkrankungen gezeigt wurde. Auch eine neue Klasse von Ceramiden, die 1-O-acylceramide, wurde entdeckt. 1-O-acylceramide könnten zu einer funktionellen Wasserdurchlässigkeit Barriere beitragen, da sie zu den hydrophobesten der epidermalen Cers gehören. Die neutrale Glucosylceramidase scheint topologisch mit der 1-Oacylceramid Produktion verbunden zu sein, sowie die Enzyme der Diacylglycerol O-Acyltransferase-2 (DGAT2) Familie eine Rolle dabei spielen könnten. Die Identifizierung der für die 1-O-acylceramid Synthese verantwortlichen Enzyme wir Gegenstand weiterer Forschung sein, jedoch zeigten Untersuchungen an Mäusen, defizient für die saure Ceramidase (Farber-Krankheit), dass Makrophagen ein weiterer potenzieller Produktionsort sein könnten.

Prediction and measurement of forced response of a composite blade undergoing nonlinear vibration

The main objective of this project is to experimentally demonstrate geometrical nonlinear phenomena due to large displacements during resonant vibration of composite materials and to explain the problem associated with fatigue prediction at resonant conditions. Three different composite blades to be tested were designed and manufactured, being their difference in the composite layup (i.e. unidirectional, cross-ply, and angle-ply layups). Manual envelope bagging technique is explained as applied to the actual manufacturing of the components; problems encountered and their solutions are detailed. Forced response tests of the first flexural, first torsional, and second flexural modes were performed by means of a uniquely contactless excitation system which induced vibration by using a pulsed airflow. Vibration intensity was acquired by means of Polytec LDV system. The first flexural mode is found to be completely linear irrespective of the vibration amplitude. The first torsional mode exhibits a general nonlinear softening behaviour which is interestingly coupled with a hardening behaviour for the unidirectional layup. The second flexural mode has a hardening nonlinear behaviour for either the unidirectional and angle-ply blade, whereas it is slightly softening for the cross-ply layup. By using the same equipment as that used for forced response analyses, free decay tests were performed at different airflow intensities. Discrete Fourier Trasform over the entire decay and Sliding DFT were computed so as to visualise the presence of nonlinear superharmonics in the decay signal and when they were damped out from the vibration over the decay time. Linear modes exhibit an exponential decay, while nonlinearities are associated with a dry-friction damping phenomenon which tends to increase with increasing amplitude. Damping ratio is derived from logarithmic decrement for the exponential branch of the decay.

Nail Lichen Planus: Successful Treatment with Etanercept

BACKGROUND: Etanercept is a fully human tumor necrosis factor a receptor fusion protein that binds tumor necrosis factor a with greater affinity than natural receptors. Biologics are widely used in the treatment of psoriasis and psoriasis arthritis and may represent a new therapeutic option for some patients with psoriatic nail disease. CASE REPORT: We report a case of lichen planus limited to the toe nails successfully treated with etanercept monotherapy. CONCLUSION: The significant improvement of our case suggests that etanercept is an effective treatment modality for lichen planus limited particularly to the nails. Further controlled studies are needed to establish the effectiveness and therapeutic regimes.

Relevance of in vitro tests of adhesive and composite dental materials, a review in 3 parts. Part 1: Approval requirements and standardized testing of composite materials according to ISO specifications

The first part of this three-part review on the relevance of laboratory testing of composites and adhesives deals with approval requirements for composite materials. We compare the in vivo and in vitro literature data and discuss the relevance of in vitro analyses. The standardized ISO protocols are presented, with a focus on the evaluation of physical parameters. These tests all have a standardized protocol that describes the entire test set-up. The tests analyse flexural strength, depth of cure, susceptibility to ambient light, color stability, water sorption and solubility, and radiopacity. Some tests have a clinical correlation. A high flexural strength, for instance, decreases the risk of fractures of the marginal ridge in posterior restorations and incisal edge build-ups of restored anterior teeth. Other tests do not have a clinical correlation or the threshold values are too low, which results in an approval of materials that show inferior clinical properties (e.g., radiopacity). It is advantageous to know the test set-ups and the ideal threshold values to correctly interpret the material data. Overall, however, laboratory assessment alone cannot ensure the clinical success of a product.

Anisotropic Mechanical Properties of ABS Parts Fabricated by Fused Deposition Modelling

In recent years, layered manufacturing (LM) processes have begun to progress from rapid prototyping techniques towards rapid manufacturing methods, where the objective is now to produce finished components for potential end use in a product (Caulfield et al., 2007). LM is especially promising for the fabrication of specific need, low volume products such as replacement parts for larger systems. This trend accentuates the need for a thorough understanding of the associated mechanical properties and the resulting behavior of parts produced by layered methods. Not only must the base material be durable, but the mechanical properties of the layered components must be sufficient to meet in-service loading and operational requirements, and be reasonably comparable to parts produced by more traditional manufacturing techniques. This chapter presents the details of a study completed to quantitatively analyze the potential of fused deposition modelling to fully evolve into a rapid manufacturing tool. The project objective is to develop an understanding of the dependence of the mechanical properties of FDM parts on raster orientation and to assess whether these parts are capable of maintaining their integrity while under service loading. The study examines the effect of fiber orientation, i.e. the direction of the polymer beads relative to the loading direction of the part, on a variety of important mechanical properties of ABS components fabricated by fused deposition modeling. Tensile, compressive, flexural, impact, and fatigue strength properties of FDM specimens are examined, evaluated, and placed in context in comparison with the properties of injection molded ABS parts.

Homeodomain-only protein HOP is a novel modulator of late differentiation in keratinocytes

The homeodomain-only protein (HOP) contains an atypical homeodomain which is unable to bind to DNA due to mutations in residues important for DNA binding. Recently, HOP was reported to regulate proliferation/differentiation homeostasis in different cell types. In the present study, we performed transcriptional profiling of cultured primary human keratinocytes and noted a robust induction of HOP upon calcium-induced cell differentiation. Immunohistochemistry of human skin localized HOP to the granular layer in the epidermis. Overexpression of HOP using a lentiviral vector up-regulated FLG and LOR expression during keratinocyte differentiation. Conversely, decreasing HOP expression using small interfering RNA markedly reduced the calcium-induced expression of late markers of differentiation in vitro, with the most prominent effect on profilaggrin (FLG) mRNA. Moreover, mRNA levels of profilaggrin and loricrin were downregulated in the epidermis of HOP knockout mice. Analysis of skin disorders revealed altered HOP expression in lichen planus, psoriasis and squamous cell carcinoma (SCC). Our data indicate that HOP is a novel modulator of late terminal differentiation in keratinocytes.

A Metric to Evaluate and Synthesize Distributed Compliant Mechanisms

Compliant mechanisms with evenly distributed stresses have better load-bearing ability and larger range of motion than mechanisms with compliance and stresses lumped at flexural hinges. In this paper, we present a metric to quantify how uniformly the strain energy of deformation and thus the stresses are distributed throughout the mechanism topology. The resulting metric is used to optimize cross-sections of conceptual compliant topologies leading to designs with maximal stress distribution. This optimization framework is demonstrated for both single-port mechanisms and single-input single-output mechanisms. It is observed that the optimized designs have lower stresses than their nonoptimized counterparts, which implies an ability for single-port mechanisms to store larger strain energy, and single-input single-output mechanisms to perform larger output work before failure.

Using the Natural Period of a Structure as an Indicator of the Significance of Second-Order Effects

This study investigates the feasibility of predicting the momentamplification in beam-column elements of steel moment-resisting frames using the structure's natural period. Unlike previous methods, which perform moment-amplification on a story-by-story basis, this study develops and tests two models that aim to predict a global amplification factor indicative of the largest relevant instance of local moment amplification in the structure. To thisend, a variety of two-dimensional frames is investigated using first and secondorder finite element analysis. The observed moment amplification is then compared with the predicted amplification based on the structure's natural period, which is calculated by first-order finite element analysis. As a benchmark, design moment amplification factors are calculated for each story using the story stiffness approach, and serve to demonstrate the relativeconservatism and accuracy of the proposed models with respect to current practice in design. The study finds that the observed moment amplification factors may vastly exceed expectations when internal member stresses are initially very small. Where the internal stresses are small relative to the member capacities, thesecases are inconsequential for design. To qualify the significance of the observed amplification factors, two parameters are used: the second-order moment normalized to the plastic moment capacity, and the combined flexural and axial stress interaction equations developed by AISC

Influence of Surface Roughness on Mechanical Properties of Two Computer-aided Design/Computer-aided Manufacturing (CAD/CAM) Ceramic Materials

SUMMARY The aim of this study was to evaluate the influence of surface roughness on surface hardness (Vickers; VHN), elastic modulus (EM), and flexural strength (FLS) of two computer-aided design/computer-aided manufacturing (CAD/CAM) ceramic materials. One hundred sixty-two samples of VITABLOCS Mark II (VMII) and 162 samples of IPS Empress CAD (IPS) were ground according to six standardized protocols producing decreasing surface roughnesses (n=27/group): grinding with 1) silicon carbide (SiC) paper #80, 2) SiC paper #120, 3) SiC paper #220, 4) SiC paper #320, 5) SiC paper #500, and 6) SiC paper #1000. Surface roughness (Ra/Rz) was measured with a surface roughness meter, VHN and EM with a hardness indentation device, and FLS with a three-point bending test. To test for a correlation between surface roughness (Ra/Rz) and VHN, EM, or FLS, Spearman rank correlation coefficients were calculated. The decrease in surface roughness led to an increase in VHN from (VMII/IPS; medians) 263.7/256.5 VHN to 646.8/601.5 VHN, an increase in EM from 45.4/41.0 GPa to 66.8/58.4 GPa, and an increase in FLS from 49.5/44.3 MPa to 73.0/97.2 MPa. For both ceramic materials, Spearman rank correlation coefficients showed a strong negative correlation between surface roughness (Ra/Rz) and VHN or EM and a moderate negative correlation between Ra/Rz and FLS. In conclusion, a decrease in surface roughness generally improved the mechanical properties of the CAD/CAM ceramic materials tested. However, FLS was less influenced by surface roughness than expected.

Survivin in skin pathologies

Survivin is a member of the inhibitor of apoptosis (IAP) protein family acting at the intersection between proliferation and cell survival. This protein exhibits low or undetectable expression in most adult tissues but is increased in the majority of cancers. Suggested to be one of the most cancer-specific proteins identified to date, survivin acts as a signalling node in tumour maintenance and, after first promising results, is now attracting increasing attention as a target in anti-cancer therapy. In the skin, survivin has been implicated in a number of pathological conditions such as psoriasis and tumours of melanocytic and epithelial origin. Its expression can correlate with tumour severity, metastasis and decreased patient survival and has been inversely correlated with the sensitivity to cytotoxic agents used in anti-cancer therapy. Survivin may also be of importance for normal epidermal homeostasis possibly supporting self-renewal of epidermal stem cells. In this review, the authors summarize and discuss current data of survivin in skin biology and provide a comprehensive compilation of survivin expression in skin pathologies with focus on future therapeutical use.

Multiscale Characterization of Acrylic Bone Cement Modified with Functionalized Mesoporous Silica Nanoparticles

Acrylic bone cement is widely used to anchor orthopedic implants to bone and mechanical failure of the cement mantle surrounding an implant can contribute to aseptic loosening. In an effort to enhance the mechanical properties of bone cement, a variety of nanoparticles and fibers can be incorporated into the cement matrix. Mesoporous silica nanoparticles (MSNs) are a class of particles that display high potential for use as reinforcement within bone cement. Therefore, the purpose of this study was to quantify the impact of modifying an acrylic cement with various low-loadings of mesoporous silica. Three types of MSNs (one plain variety and two modified with functional groups) at two loading ratios (0.1 and 0.2 wt/wt) were incorporated into a commercially available bone cement. The mechanical properties were characterized using four-point bending, microindentation and nanoindentation (static, stress relaxation, and creep) while material properties were assessed through dynamic mechanical analysis, differential scanning calorimetry, thermogravimetric analysis, FTIR spectroscopy, and scanning electron microscopy. Four-point flexural testing and nanoindentation revealed minimal impact on the properties of the cements, except for several changes in the nano-level static mechanical properties. Conversely, microindentation testing demonstrated that the addition of MSNs significantly increased the microhardness. The stress relaxation and creep properties of the cements measured with nanoindentation displayed no effect resulting from the addition of MSNs. The measured material properties were consistent among all cements. Analysis of scanning electron micrographs images revealed that surface functionalization enhanced particle dispersion within the cement matrix and resulted in fewer particle agglomerates. These results suggest that the loading ratios of mesoporous silica used in this study were not an effective reinforcement material. Future work should be conducted to determine the impact of higher MSN loading ratios and alternative functional groups. (C) 2014 Elsevier Ltd. All rights reserved.