Allelopathic Influence of Residues from Sphagneticola trilobata on Weeds and Crops

The allelopathic effect studied in many cultures has currently generated great expectations that displayed a natural and environmentally friendly tool for weed management using bioherbicides. The objective of this work was to assess allelopathic influence of residues of S. trilobata on the germination and growth of weeds, as well as their relation with some crops and effects on soil properties. Results show that residues from S. trilobata have inhibited the germination of weeds (31.6 - 72%), increasingly with the applied dose. All residue doses of this specie have inhibited dicotyledonous germination, but only maximum concentration has affected monocotyledons. The residues did not affect onion germination, but stimulated it in radish and tomato, while the dose applied at 50% produced tomato stimulation and inhibition of cabbage. The effects of residues on hypocotyl growth in different crops showed changes in species response. For onion, the three doses had negative effects on the growth of hypocotyl, while tomato was stimulated. For radish, the growth was hindered by any dose applied, and were only different (50 and 100%) compared to control. For cabbage, only hypocotyl length was stimulated, when maximum dose (100%) was applied. For the radicle growth, in onion and radish no differences were found compared to control. While the tomato radicle growth was inhibited, in cabbage, all doses encouraged the elongation of the radicle. The dry mass of weed was affected by increased dose of residue (0.49 - 8.8 g m-2), however the soil microflora was stimulated, while the population of Azotobacter spp. was not affect. Some soil properties were affected, the level of organic material, Na+ and electrical conductivity were increased, while pH (H2O) decreased a bit, however it remained basic.

Taxonomy and distribution of the green algal genus Halimeda (Bryopsidales, Chlorophyta) in Brazil

Halimeda is a genus of calcified coenocytic green algae with a well known ecological importance in some tropical areas. Bleached calcified segments of Halimeda may accumulate in large deposits of economic potential as is the case in the northeastern coast of Brazil. In a survey of the genus in Brazil based on recent collections and examination of abundant material deposited on Brazilian herbaria we identified seven species: Halimeda cuneata Hering, H. discoidea Decaisne, H. gracilis Harvey ex J. Agardh, H. incrassata (Ellis) Lamouroux, H. opuntia (Linnaeus) Lamouroux, H. simulans Howe and H. tuna (Ellis & Solander) Lamouroux. These species are described in detail, with emphasis on diagnostic characters. Our study has shown that the shape and size of the utricula in surface view, under scanning electron microscopy, can be utilized to discriminate some species. Fertile specimens of Halimeda cuneata and H. discoidea are reported for the first time in the region. Data on vertical and geographical distribution are presented for each species and the southern limit of the genus in the western Atlantic was extended.

Intelligent mapping of stresses in a hydraulic crane

Continuous loading and unloading can cause breakdown of cranes. In seeking solution to this problem, the use of an intelligent control system for improving the fatigue life of cranes in the control of mechatronics has been under study since 1994. This research focuses on the use of neural networks as possibilities of developing algorithm to map stresses on a crane. The intelligent algorithm was designed to be a part of the system of a crane, the design process started with solid works, ANSYS and co-simulation using MSc Adams software which was incorporated in MATLAB-Simulink and finally MATLAB neural network (NN) for the optimization process. The flexibility of the boom accounted for the accuracy of the maximum stress results in the ADAMS model. The flexibility created in ANSYS produced more accurate results compared to the flexibility model in ADAMS/View using discrete link. The compatibility between.ADAMS and ANSYS softwares was paramount in the efficiency and the accuracy of the results. Von Mises stresses analysis was more suitable for this thesis work because the hydraulic boom was made from construction steel FE-510 of steel grade S355 with yield strength of 355MPa. Von Mises theory was good for further analysis due to ductility of the material and the repeated tensile and shear loading. Neural network predictions for the maximum stresses were then compared with the co-simulation results for accuracy, and the comparison showed that the results obtained from neural network model were sufficiently accurate in predicting the maximum stresses on the boom than co-simulation.

Repair of the anophthalmic cavity of rats with synthetic hydroxyapatite

We placed spheres of synthetic hydroxyapatite (calcium chloride combined with sodium phosphate) in the eviscerated or enucleated orbital cavity of rats in order to evaluate the biocompatibility of this material with the orbital cavity. The study was conducted on 50 albino rats, 25 of which were submitted to enucleation and 25 to evisceration of one eye. The animals were sacrificed 7, 15, 21, 30 and 60 days after surgery and the orbital content was submitted to histopathological examination. A reaction of the young granulation tissue type was observed first. The hydroxyapatite was gradually surrounded by a granulomatous macrophage inflammatory response and covered with dense connective tissue that formed a sort of" mesh" septating and supporting progressively smaller blocks of the substance. The same type of reaction was observed in the enucleated and eviscerated cavities. We conclude that synthetic hydroxyapatite is an inert nonallergenic material which is appropriate for volume replacement in the anophthalmic cavity

Improving the usability of extruded wood-plastic composites by using modification technology

Using cellulosic reinforcement to produce plastic composites is a globally growing trend. One of such materials are wood-plastic composites, which are an extensively studied group of materials for which the global industry is looking for new applications. Issues such as bondability, durability and fire resistance still require development to improve the usability of the wood-plastic composite material. Improvement of the usability of wood-plastic composites is studied in this thesis through the effects of using selected modification technology in wood and plastic industry. The applied modification methods are surface by mechanical abrasion and plasma, chemical impregnation of wood flour, and structural modification by the co-extrusion process. The study shows that the properties of WPC can be influenced by the selected modification methods. The selected methods are also found to be able to result as improvement in the properties of the material. The may also affect other than just the targeted properties of the end-product, either in a positive or a negative manner. Therefore modification as performance improvement should be considered as a caseby- case study. Introducing WPC materials for new applications can be done by using modification technology. Structuralmodification can possibly be used to reduce material costs of the modified WPC material.

Role of Tamm-Horsfall protein and uromodulin in calcium oxalate crystallization

One of the defenses against nephrolithiasis is provided by macromolecules that modulate the nucleation, growth, aggregation and retention of crystals in the kidneys. The aim of the present study was to determine the behavior of two of these proteins, Tamm-Horsfall and uromodulin, in calcium oxalate crystallization in vitro. We studied a group of 10 male stone formers who had formed at least one kidney stone composed of calcium oxalate. They were classified as having idiopathic nephrolithiasis and had no well-known metabolic risk factors involved in kidney stone pathogenesis. Ten normal men were used as controls, as was a group consisting of five normal women and another consisting of five pregnant women. Crystallization was induced by a fixed supersaturation of calcium oxalate and measured with a Coulter Counter. All findings were confirmed by light and scanning electron microscopy. The number of particulate material deposited from patients with Tamm-Horsfall protein was higher than that of the controls (P<0.001). However, Tamm-Horsfall protein decreased the particle diameter of the stone formers when analyzed by the mode of the volume distribution curve (P<0.002) (5.64 ± 0.55 µm compared to 11.41 ± 0.48 µm of uromodulin; 15.94 ± 3.93 µm and 12.45 ± 0.97 µm of normal men Tamm-Horsfall protein and uromodulin, respectively; 8.17 ± 1.57 µm and 9.82 ± 0.95 µm of normal women Tamm-Horsfall protein and uromodulin, respectively; 12.17 ± 1.41 µm and 12.99 ± 0.51 µm of pregnant Tamm-Horsfall protein and uromodulin, respectively). Uromodulin produced fewer particles than Tamm-Horsfall protein in all groups. Nonetheless, the total volume of the crystals produced by uromodulin was higher than that produced by Tamm-Horsfall protein. Our results indicate a different effect of Tamm-Horsfall protein and uromodulin. This dual behavior suggests different functions. Tamm-Horsfall protein may act on nucleation and inhibit crystal aggregation, while uromodulin may promote aggregation of calcium oxalate crystals.

Prevalence of Y chromosome deletions in a Brazilian population of nonobstructive azoospermic and severely oligozoospermic men

We determined the prevalence of Y chromosome deletions in a population of 60 Brazilian nonobstructive azoospermic and severely oligozoospermic men. PCR-based screening of microdeletions was performed on lymphocyte DNA for the presence of 14 sequence-tagged sites (STS) located in the azoospermic factor (AZF) on the Yq chromosome. All STS were amplified efficiently in samples from 12 fertile men tested, but failed to be amplified in samples from fertile women, indicating the specificity of PCR conditions for Yq screening. Overall, 4 of the 60 infertile patients tested (6.7%) exhibited deletion of the Y chromosome, 2 of them being severely oligozoospermic patients (P10 and P32) and 2 azoospermic men (patients P47 and P57). Patients P47 and P57 presented larger deletions in the AZFa, AZFb and AZFc subregions, with apparent loss of Yq material evidenced by karyotype analysis. Patients P10 and P32 presented deletions confined to the AZFc region, involving the DAZ locus. Male relatives of patients P10 and P32 had no Y chromosome deletions and presented a normal karyotype, suggesting a de novo status of the deletions found. Our data add to the growing literature showing that microdeletions of the Y chromosome can be the cause of male idiopathic infertility.

Low variation in ribosomal DNA and internal transcribed spacers of the symbiotic fungi of leaf-cutting ants (Attini: Formicidae)

Leaf-cutting ants of the genera Atta and Acromyrmex (tribe Attini) are symbiotic with basidiomycete fungi of the genus Leucoagaricus (tribe Leucocoprineae), which they cultivate on vegetable matter inside their nests. We determined the variation of the 28S, 18S, and 5.8S ribosomal DNA (rDNA) gene loci and the rapidly evolving internal transcribed spacers 1 and 2 (ITS1 and ITS2) of 15 sympatric and allopatric fungi associated with colonies of 11 species of leafcutter ants living up to 2,600 km apart in Brazil. We found that the fungal rDNA and ITS sequences from different species of ants were identical (or nearly identical) to each other, whereas 10 GenBank Leucoagaricus species showed higher ITS variation. Our findings suggest that Atta and Acromyrmex leafcutters living in geographic sites that are very distant from each other cultivate a single fungal species made up of closely related lineages of Leucoagaricus gongylophorus. We discuss the strikingly high similarity in the ITS1 and ITS2 regions of the Atta and Acromyrmex symbiotic L. gongylophorus studied by us, in contrast to the lower similarity displayed by their non-symbiotic counterparts. We suggest that the similarity of our L. gongylophorus isolates is an indication of the recent association of the fungus with these ants, and propose that both the intense lateral transmission of fungal material within leafcutter nests and the selection of more adapted fungal strains are involved in the homogenization of the symbiotic fungal stock.

Effect of an isotonic rehydration sports drink and exercise on urolithiasis in rats

The objective of the present study was to evaluate the role of physical exercise as well as the influence of hydration with an isotonic sports drink on renal function in male Wistar rats. Four groups were studied over a period of 42 days: 1) control (N = 9); 2) physical exercise (Exe, N = 7); 3) isotonic drink (Drink, N = 8); 4) physical exercise + isotonic drink (Exe + Drink, N = 8). Physical exercise consisted of running on a motor-driven treadmill for 1 h/day, at 20 m/min, 5 days a week. The isotonic sports drink was a commercial solution used by athletes for rehydration after physical activity, 2 ml administered by gavage twice a day. Urine cultures were performed in all animals. Twenty-four-hour urine samples were collected in metabolic cages at the beginning and at the end of the protocol period. Urinary and plasma parameters (sodium, potassium, urea, creatinine, calcium) did not differ among groups. However, an amorphous material was observed in the bladders of animals in the Exe + Drink and Drink groups. Characterization of the material by Western blot revealed the presence of Tamm-Horsfall protein and angiotensin converting enzyme. Physical exercise and the isotonic drink did not change the plasma or urinary parameters measured. However, the isotonic drink induced the formation of intravesical matrix, suggesting a potential lithogenic risk.

Adsorption of arsenic from ammonia containing waste water by ferrous hydroxide waste

Arsenic is a toxic substance. The amount of arsenic in waste water is a raising problem because of increasing mining industry. Arsenic is connected to cancers in areas where arsenic concentration in drinking water is higher than recommendations. The main object in this master’s thesis was to research how ferrous hydroxide waste material is adsorbed arsenic from ammonia containing waste water. In this master’s thesis there is two parts: theoretical and experimental part. In theoretical part harmful effects of arsenic, theory of adsorption, isotherms modeling of adsorption and analysis methods of arsenic are described. In experimental part adsorption capacity of ferrous hydroxide waste material and adsorption time with different concentrations of arsenic were studied. Waste material was modified with two modification methods. Based on experimental results the adsorption capacity of waste material was high. The problem with waste material was that at same time with arsenic adsorption sulfur was dissolving in solution. Waste material was purified from sulfur but purification methods were not efficient enough. Purification methods require more research.

Intensification of hemicellulose hot-water extraction from spruce wood by parameter tuning

The growing population on earth along with diminishing fossil deposits and the climate change debate calls out for a better utilization of renewable, bio-based materials. In a biorefinery perspective, the renewable biomass is converted into many different products such as fuels, chemicals, and materials, quite similar to the petroleum refinery industry. Since forests cover about one third of the land surface on earth, ligno-cellulosic biomass is the most abundant renewable resource available. The natural first step in a biorefinery is separation and isolation of the different compounds the biomass is comprised of. The major components in wood are cellulose, hemicellulose, and lignin, all of which can be made into various end-products. Today, focus normally lies on utilizing only one component, e.g., the cellulose in the Kraft pulping process. It would be highly desirable to utilize all the different compounds, both from an economical and environmental point of view. The separation process should therefore be optimized. Hemicelluloses can partly be extracted with hot-water prior to pulping. Depending in the severity of the extraction, the hemicelluloses are degraded to various degrees. In order to be able to choose from a variety of different end-products, the hemicelluloses should be as intact as possible after the extraction. The main focus of this work has been on preserving the hemicellulose molar mass throughout the extraction at a high yield by actively controlling the extraction pH at the high temperatures used. Since it has not been possible to measure pH during an extraction due to the high temperatures, the extraction pH has remained a “black box”. Therefore, a high-temperature in-line pH measuring system was developed, validated, and tested for hot-water wood extractions. One crucial step in the measurements is calibration, therefore extensive efforts was put on developing a reliable calibration procedure. Initial extractions with wood showed that the actual extraction pH was ~0.35 pH units higher than previously believed. The measuring system was also equipped with a controller connected to a pump. With this addition it was possible to control the extraction to any desired pH set point. When the pH dropped below the set point, the controller started pumping in alkali and by that the desired set point was maintained very accurately. Analyses of the extracted hemicelluloses showed that less hemicelluloses were extracted at higher pH but with a higher molar-mass. Monomer formation could, at a certain pH level, be completely inhibited. Increasing the temperature, but maintaining a specific pH set point, would speed up the extraction without degrading the molar-mass of the hemicelluloses and thereby intensifying the extraction. The diffusion of the dissolved hemicelluloses from the wood particle is a major part of the extraction process. Therefore, a particle size study ranging from 0.5 mm wood particles to industrial size wood chips was conducted to investigate the internal mass transfer of the hemicelluloses. Unsurprisingly, it showed that hemicelluloses were extracted faster from smaller wood particles than larger although it did not seem to have a substantial effect on the average molar mass of the extracted hemicelluloses. However, smaller particle sizes require more energy to manufacture and thus increases the economic cost. Since bark comprises 10 – 15 % of a tree, it is important to also consider it in a biorefinery concept. Spruce inner and outer bark was hot-water extracted separately to investigate the possibility to isolate the bark hemicelluloses. It was showed that the bark hemicelluloses comprised mostly of pectic material and differed considerably from the wood hemicelluloses. The bark hemicelluloses, or pectins, could be extracted at lower temperatures than the wood hemicelluloses. A chemical characterization, done separately on inner and outer bark, showed that inner bark contained over 10 % stilbene glucosides that could be extracted already at 100 °C with aqueous acetone.

Sekajätteen koostumustutkimusten luokitteluohjeen päivittäminen ja testaaminen

Tässä diplomityössä päivitettiin ja testattiin sekajätteen koostumustutkimuksiin tarkoitettua jätejakeiden luokitteluohjetta. Työn tavoitteena oli selvittää, miten luokitteluohje vastaa jätelainsäädännön muutoksiin ja tavoitteisiin, miten ohje toimii käytännössä sekä miten luokitteluohjetta tulee päivittää, jotta se sekä vastaa jätelainsäädännön ja jätealan toimijoiden tietotarpeisiin sekajätteen koostumuksesta että toimii myös käytännössä. Työssä toteutettiin kyselytutkimus ja kaksi sekajätteen koostumustutkimusta. Jätealan toimijoille lähetetyn kyselyn avulla kartoitettiin luokitteluohjeen kehityskohtia. Kyselytutkimuksen vastaajat kokivat, että luokitteluohjeessa on eniten kehitettävää muovien luokittelussa. Muovien luokittelun lisäksi biojätteen sekä kierrätettävien ja vaarallisten jätteiden luokitteluun liittyvät mahdolliset kehityskohdat muodostettiin kyselyn vastausten perusteella. Sekajätteen koostumustutkimusten avulla testattiin luokitteluohjeen toimivuutta. Koostumustutkimukset toteutettiin ohjeen tarkimman tason mukaisesti. Jätteiden lajittelu osoittautui huomattavasti hitaammaksi kuin etukäteen oli arvioitu. Lisäksi monia materiaaleja sisältävien jätteiden lajittelu oli haasteellista molemmissa tutkimuksissa. Luokitteluohjetta päivitettiin kyselytutkimuksen ja koostumustutkimusten perusteella. Jätteet on luokiteltu päivitetyssä ohjeessa alkuperäisen ohjeen tavoin jätemateriaalien perusteella. Luokitteluohjetta päivitettiin jäteluokkien termistön sekä keittiöjätteen ja kierrätettävien jätteiden luokittelun osalta. Päivitetyn ohjeen avulla koostumustutkimuksen toteuttaja saa enemmän tietoa sekajätteestä biojätteen sekä kierrätettävien jätteiden osalta, mikä on tärkeää jätelainsäädännöllisten tavoitteiden kannalta.

First-principles study on electronic and structural properties of Cu(In/Ga)Se alloys for solar cells

Thin-film photovoltaic solar cells based on the Cu(In1−xGax)Se2 (CIGS) alloys have attracted more and more attention due to their large optical absorption coefficient, long term stability, low cost, and high efficiency. Modern theoretical studies of this material with first-principles calculations can provide accurate description of the electronic structure and yield results in close agreement with experimental values, but takes a large amount of calculation time. In this work, we use first-principles calculations based on the computationally affordable meta- generalized gradient approximation of the density-functional theory to investigate electronic and structural properties of the CIGS alloys. We report on the simulation of the lattice parameters and band gaps, as a function of chemical composition. The obtained results were found to be in a good agreement with the available experimental data.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Chemical composition of tempeh from soybean cultivars specially developed for human consumption

Tempeh is a food obtained by fermentation of soybean grains by the fungus Rizophus oligosporus. It is a traditional Indonesian food that presents benefits for human health protecting against diarrhea and chronic diseases. Tempeh processing includes dehulling, cooking, inoculation, and fermentation. In this study, chemical characteristics of tempeh prepared with soybean cultivars specially developed for human consumption (BRS 216, BRS 232, BRS 257, and BRS 267) were investigated. Soybean grains and tempeh obtained from these cultivars were analyzed for oil, protein, antinutrional factors, and isoflavone content. Cultivar BRS 216 presented the highest protein content in the grains (36.81%) and in tempeh (51.99%). On average, the protein content in tempeh increased 16% in relation to that of soybean grains. Isoflavone content was higher in the grains than in tempeh with significant differences among the cultivars. However, the aglycones content increased about 50% in tempeh (49.00 mg.100 g-1 on average) compared to that of raw material (soybean grains - 21.49 mg.100 g-1, on average). The content of Kunitz trypsin inhibitor (KSTI) reduced 83% in tempeh, on average, as compared to the value found in the grains. Phytic acid content was similar in both tempeh and the grains.