Effect of dietary sodium restriction on taste perception of sodium chloride

The effect of dietary sodium restriction on perceived intensity of and preference for the taste of salt was evaluated in 76 adults, 25-49 years, with diastolic blood pressure between 79-90 mmHg. Participants were volunteers from clinical Hypertension Prevention Trials (HPT), at the University of California, Davis and the University of Minnesota, Minneapolis. Participants followed one of four HPT diets: 1600 mg Na+/day (NA, n=lS), 1600 mg Na+ plus 3200 mg K+/day (NK, n=lS), 1600 mg Na+/day plus energy restriction to achieve weight loss (NW, n=l3) and weight loss only (WT, n=l3). All participants attended regularly scheduled nutri­tion intervention meetings designed to help them achieve the HPT dietary goals. A fifth, no-intervention group, consisted of 20, no-diet-change controls CCN). Sodium, potassium and energy intakes were monitored by analysis of single, 24-hour food records and corresponding overnight urine speci­mens, obtained at baseline and after 12 and 24 weeks of intervention. Hedonic responses to sodium chloride in a prepared cream of green bean soup were assessed by two methods : 1) scaling of like/dislike for an NaCl concentration series on 10-cm graphie line scales and 2) ad libitum mixing of unsalted and salted soups to maximum level of liking. Salt content of the mixes was analyzed by sodium ion-selective electrode. The concentration series was also rated for perceived saltiness­intensity on similar graphie line scales. Tests were conducted at base­line and after approximately 1, 3, 6, 8, 10, 13 and 24 weeks of intervention. Reduction in sodium intake and excretion in NA, NK and NW partici­pants was accompanied by a shift in preference toward less saltiness in soup. The pattern of hedonic responses changed over time: scores for high NaCl concentrations decreased progressively while scores for low concentrations increased. Hedonic maxima shifted fran a concentration of 0.55% at the onset to 0.1-0.2% added NaCl at week 24. During the same time period, the preferred concentration of ad libitum mixes declined 50%. These shifts occurred independently of changes in salti­ness intensity ratings, potassium or energy intakes, and were consistent across the two participating study sites. Like/dislike and sd. libitum responses were similar after 13 and 24 weeks of diet, as were measures of sodium intake and excretion. These findings suggest that after three months of sodium restriction, preference for salt had readjusted to a lower level, reflective of lower sodium intake. Mechanisms underlying the change in preference are unclear, but may include sensory, context, physiological as well as behavioral effects. In contrast, few changes were noted within WT and CN groups. The pattern of hedonic responses varied little in controls while the WT group showed increased liking for mid-range NaCl concentrations. Small, but significant fluctuations in ad libitum mix concentration occurred in both of these groups, but the differences appeared to be random rather than systematic. The results of this study indicate that preference for the taste of salt declines progressively toward a new baseline following reductions in sodium intake. These alterations may enhance maintenance of low­sodium diets for the treatment and prevention of hypertension. Further investigation is needed to establish the degree to which long-term com­pliance is contingent upon variation in salt taste preference.

Stress parental et lien mère-enfant: impact sur le développement de l’enfant âgé d’un an.

Au cours de la grossesse et dans les premières années de vie de l’enfant, plusieurs facteurs externes, tels que le stress maternel ou le lien maternel, peuvent interférer avec son développement et avoir des conséquences à court et à long terme. Bien que le stress maternel périnatal ait souvent été étudié, plusieurs facteurs pré et postnataux potentiellement confondants (comme le stress paternel, la dépression, la prise d’antidépresseurs, etc.) n’ont pas systématiquement été pris en compte. Comparativement à l’attachement de l’enfant (à sa mère), moins de recherches se sont intéressées au lien maternel, en particulier chez des femmes ayant un diagnostic de dépression et/ou d’anxiété et exposées à des antidépresseurs. Notre thèse visait donc à étudier ces deux facteurs et leur association avec le développement du jeune enfant âgé d’un an, dans un contexte où la santé mentale maternelle (présence ou non de troubles psychologiques) et de traitements pharmacologiques associés étaient aussi considérés. Afin d’améliorer le dépistage de retards développementaux, nous avons également évalué l’administration au téléphone de deux instruments de pré-dépistage et dépistage actuellement utilisés. Notre thèse était constituée de quatre phases dont les objectifs étaient: la détermination des propriétés psychométriques de l’échelle de stress perçu de quatre items (en français et en anglais) au sein de la population de femmes enceintes (première étude); évaluer l’effet du stress maternel prénatal et parental postnatal sur le développement de l’enfant âgé d’un an (deuxième étude); estimer l’association entre le lien maternel et le développement de l’enfant âgé d’un an, en stratifiant sur la prise maternelle d’antidépresseurs (troisième étude); et évaluer l’administration au téléphone du ″Ages and Stages Questionnaire″ (ASQ, version de 12 mois) et du ″Revised Pre-screening Denver Questionnaire″(R-PDQ, version de 9-24 mois),deux questionnaires utilisés pour le pré-dépistage et le dépistage du développement infantile (quatrième étude). Ce projet faisait partie d’une plus grande étude, nommée le projet OTIS (The″Organization of Teratology Information Specialists″ Antidepressant in Pregnancy cohort study), qui visait à évaluer l’impact de l’arrêt versus la continuation de la prise d’antidépresseurs au cours de la grossesse sur les comportements maternels et sur le développement de l’enfant âgé de un à trois ans. Ainsi, entre 2006 et 2010, la cohorte prospective OTIS de femmes enceintes a été construite et suivie jusqu’à trois ans postpartum. À partir de 2008, l’évaluation du stress et du lien maternel (thématiques de ce projet de thèse) a été incorporée au projet initial. Aussi, à partir de là, toute femme nouvellement recrutée pour la cohorte OTIS pouvait faire partie des études de cette thèse. Notre population source était composée des femmes enceintes ayant eu recours à un service nord-américain d’information sur les tératogènes ou ayant été suivies à la clinique d'obstétrique et de gynécologie du CHU Ste Justine. Pour être admissibles, les femmes devaient 1) être âgées d’au moins 18 ans, 2) être enceinte d’au maximum 14 semaines (le début de la grossesse étant défini comme étant le premier jour des dernières règles); 3) être exposées à un antidépresseur depuis au moins le premier jour de grossesse (pour le groupe exposé à un antidépresseur), 4) savoir lire et comprendre l’anglais ou le français. Pour les études deux, trois et quatre, les femmes devaient habiter dans un rayon de 250 km autour de Montréal pour recevoir notre visite à domicile, nécessaire à l’évaluation psychométrique du développement infantile. Les pères des enfants ont été recrutés à deux mois postpartum pour évaluer leur stress. Les données ont été collectées par entrevue téléphonique, auto-administration de questionnaires, et évaluation psychométrique du développement infantile. Dans le cadre de cette thèse, les femmes étaient suivies depuis le premier trimestre de grossesse jusqu’à un an postpartum. Les résultats de nos travaux démontrent que le recours à l’échelle de stress perçu de quatre items est une mesure fiable et valide pour mesurer le stress au cours de la grossesse (en recherche ou en clinique). Ensuite, le stress postnatal maternel et paternel serait défavorable au développement moteur et socio-émotionnel de l’enfant d’un an, respectivement. Par contre le stress maternel prénatal favoriserait le développement moteur. Un lien maternel optimal est associé à un meilleur développement socio-émotionnel à un an chez l’enfant, en particulier pour les femmes exposées à des antidépresseurs. Enfin, l’administration au téléphone de l’ASQ et des sous-échelles de langage, de motricité fine et motricité globale du R-PDQ serait une alternative possible au mode auto-administré pour dépister et pré-dépister les retards de développement chez les enfants.

Rheological Characteristics of Short Nylon -6 Fiber Reinforced Styrene Butadiene Rubber Containing Epoxy Resin as Bonding Agent

The rheological characteristics of short Nylon-6 fiber-reinforced Styrene Butadiene rubber (SBR) in the presence of epoxy resin-based bonding agent were studied with respect to the effect of shear rate, fiber concentration , and temperature on shear viscosity and die swell using a capillary rheonzeter. All the composites containing bonding agent showed a pseudoplastic nature, which decreased with increasing temperature. Shear viscosity was increased in the presence of fibers. The temperature sensitivity of the SBR matrices was reduced on introduction of fibers. The temperature sensitivity of the melts was found to be lower at higher shear rates. Die swell was reduced in the presence of fibers. Relative viscosity of the composites increased with shear rate. In the presence of epoxy resin bonding agent the temperature sensitivity of the mixes increased. Die swell was larger in the presence of bonding agent.

Rheology of Short Nylon -6 Fiber Reinforced Styrene-Butadiene Rubber

The rheological characteristics of short Nylon-6 fiber reinforced styrene butadiene rubber (SBR) were studied using a capillary rheometer. The study was done with respect to the effect of shear rate, fiber concentration, and temperature on shear viscosity and die swell. All the melts showed pseudoplastic nature, which decreased with increasing temperature. Shear viscosity increased in the presence of fibers. Introduction of fiber reduces the temperature sensitivity of the rubber matrix. A reduction in die swell was found in presence of fibers.

Thermal Degradation of Short Nylon -6 Fiber-Reinforced Styrene Butadiene Rubber Composite

The thermal properties of short Nylon-6 fiber-reinforced Styrene butadiene rubber (SBR) composites were studied by Thermogravimetric Analysis (TGA). The effect of epoxy-based bonding agent on thermal degradation of the gum and the composites was also studied. The thermal stability of the SBR was enhanced in the presence of Nylon-6 fibers and the stability of the composites increased in the presence of bonding agent. The epoxy resin did not significantly change the thermal stability of SBR gum vulcanizate. Results of kinetic studies showed that the degradation of SBR and the short nylon fiber-reinforced composites with and without bonding agents followed first-order kinetics.

Short Isora Fibre Reinforced Natural Rubber Composites

The present study deals with the short isora fibre reinforced natural rubber composites. In recent years there has been a tremendous advancement in the field of science and technology of short fibre reinforced polymer composites. The low density, high strength, high stiffness to weight ratio, excellent durability and design flexibility are the primary reasons for their use in many diversified fields such as air crafts, automobiles, marine industry etc. Compared to the various natural and synthetic fibres used as reinforcement for elastomer composites isora fibre is superior in many aspects. `Isora' is a natural lignocellulosic fibre which is easily available in South India especially in Kerala. The fibre is separated from the bark of the Helicteres isora plant by retting process. This fibre has excellent mechanical properties and is easily amenable to physical and chemical modifications. The study shows that composites with poor interfacial bonding tend to dissipate more energy than that with to interfacial bonding. The mechanical loss also can be related to interfacial bonding. The effect of chemical treatment of isora fibre on damping was also studied. Both in the low and high temperature region which indicates that this composite posseses low damping and hence good interfacial bonding characteristics. Hence these composites are better candidates for high damping applications. Composites with longitudinally oriented fibres showed high storage modulus than transversely oriented ones due to the effective stress transfer between fibre and matrix.

Studies on short nylon fiber - reclaimed rubber/elastomer composites

The thesis deals with the development of short nylon fiber-reclaimed rubber/elastomer composites. Three rubbers viz, natural rubber, acrylonitrile butadiene rubber and styrene butadiene rubber were selected and were partially replaced with reclaimed rubber. The blend ratio was optimized with respect to cure characteristics and mechanical properties. Reclaimed rubber replaced 40 parts of NR and SBR and 20 parts of NBR without much affecting the properties. These blends were then reinforced with short nylon fibers. The mechanical properties of the composites were studied in detail. In all the cases the tensile strength, tear strength and the abrasion resistance increased with increase in fiber content. In the case of NRlreclaimed rubber blends, the tensile strength-fiberloading relationship was non-linear where as in the case of NBRlreclaimed rubber blends and SBRlreclaimed rubber blends the tensile strength-fiber loading relationship was linear. All the composites showed anisotropy in mechanical properties. The effect of bonding system on the composite properties was also studied with respect to cure characteristics and mechanical properties. For this, a 20 phr fiber loaded reclaimed rubber/elastomer composites were selected and the effect of MDI/PEG resin system was studied. The resin used was 5 phr and the resin ratios used were 0.67: I, 1:1, 1.5:1 and 2:1. The bonding system improved the tensile strength, tear strength and abrasion resistance. The best results are with SBRlreclaimed rubber-short nylon fiber composites. The optimized resin ratio was 1:1 MDI/PEG for all the composites.

Studies on short Nylon-6 fiber - elastomer composites with epoxy resin as bonding agent

The thesis describes the development and evaluation of epoxy resin as interfacial bonding agent for short Nylon-6 fiber elastomer composites. Epoxy resin is well known for its adhesive property. The potential use of it as interfacial bonding agent in short fiber composite is not explored yet. Three rubbers viz., acrylonitrile butadiene rubber (NBR), Neoprene rubber (CR) and styrene butadiene rubber (SBR) were selected and different fiber loading were tried. The resin concentration was optimized for each fiber loading with respect to cure characteristics and mechanical properties. Rheological characteristics and thermal degradation of the composites containing different fiber loading and different resin concentrations were studied in detail to find the effect of epoxy resin bonding system. The mechanical properties were studied in detail. The short Nylon -6 fiber improved most of the mechanical properties of all the three rubbers. Tensile strength showed a dip at 10 phr fiber loading in the case of CR while it was continuously increased with fiber loading in the case of NBR and SBR. All the composites showed anisotropy in mechanical properties. The epoxy resin is an effective bonding agent for short Nylon -6 fiber reinforced NBR and CR composites. Epoxy resin improved tensile strength, abrasion resistance and modulus of these composites. SEM studies confirmed the improved bonding of fiber and matrix in the presence of epoxy bonding agent. Epoxy resin was not effective as bonding agent in the case of short Nylon fiber- SBR composite. From the rheological studies of the composites with and without bonding agent it was observed that all the composite exhibited pseudoplasticity, which decreased with temperature. At higher shear rates all the mixes showed plug flow. SEM pictures showed that maximum orientation of fibers occured at a shear rate, just before the onset of plug flow. The presence of fiber reduced the temperature sensitivity of the flow at a given shear rate. Die swell was reduced in the presence of fiber. Shear viscosity of the composite was increased in the presence of resin. Die swell was increased in the presence of epoxy resin for composites at all shear rates. The thermal degradation of NBR and SBR composites with and without bonding agent followed single step degradation pattern. Thermal stability of the composites was improved in the presence of bonding agent. The degradation of virgin elastomer and the composites followed first order kinetics.

Recyclable Short Fibre Reinforced Plastics PP/Nylon and HDPE/Nylon composites

The study shows that standard plastics like polypropylene and high density polyethylene can be reinforced by adding nylon short fibres. Compared to the conventional glass reinforced thermoplastics this novel class of reinforced thermoplastics has the major advantage of recyclability. Hence such composites represent a new spectrum of recyclable polymer composites. The fibre length and fibre diameter used for reinforcement are critical parameters While there is a critical fibre length below which no effective reinforcement takes place, the reinforcement improves when the fibre diameter decreases due to increased surface area.While the fibres alone give moderate reinforcement, chemical modification of the matrix can further improve the strength and modulus of the composites. Maleic anhydride grafting in presence of styrene was found to be the most efficient chemical modification. While the fibre addition enhances the viscosity of the melt at lower shear rates, the enhancement at higher shear rate is only marginal. This shows that processing of the composite can be done in a similar way to that of the matrix polymer in high shear operations such as injection moulding. Another significant observation is the decrease in melt viscosity of the composite upon grafting. Thus chemical modification of matrix makes processing of the composite easier in addition to improving the mechanical load bearing capacity.For the development of a useful short fibre composite, selection of proper materials, optimum design with regard to the particular product and choosing proper processing parameters are most essential. Since there is a co-influence of many parameters, analytical solutions are difficult. Hence for selecting proper processing parameters 'rnold flow' software was utilized. The orientation of the fibres, mechanical properties, temperature profile, shrinkage, fill time etc. were determined using the software.Another interesting feature of the nylon fibre/PP and nylon fibre/HDPE composites is their thermal behaviour. Both nylon and PP degrade at the same temperature in single steps and hence the thermal degradation behaviour of the composites is also being predictable. It is observed that the thermal behaviour of the matrix or reinforcement does not affect each other. Almost similar behaviour is observed in the case of nylon fibre/HDPE composites. Another equally significant factor is the nucleating effect of nylon fibre when the composite melt cools down. In the presence of the fibre the onset of crystallization occurs at slightly higher temperature.When the matrix is modified by grafting, the onset of crystallization occurs at still higher temperature. Hence it may be calculated that one reason for the improvement in mechanical behaviour of the composite is the difference in crystallization behaviour of the matrix in presence of the fibre.As mentioned earlier, a major advantage of these composites is their recyclability. Two basic approaches may be employed for recycling namely, low temperature recycling and high temperature recycling. In the low temperature recycling, the recycling is done at a temperature above the melting point of the matrix, but below that of the fibres while in the high temperature route. the recycling is done at a temperature above the melting points of both matrix and fibre. The former is particularly interesting in that the recycled material has equal or even better mechanical properties compared to the initial product. This is possible because the orientation of the fibre can improve with successive recycling. Hence such recycled composites can be used for the same applications for which the original composite was developed. In high temperature recycling, the composite is converted into a blend and hence the properties will be inferior to that of the original composite, but will be higher than that of the matrix material alone.

Short Nylon-6 Fibre/Rubber-Toughened Polystyrene Composites

The thesis describes studies on development of short Nylon-6 fibre composites based on rubber-toughened polystyrene (PS). Toughening was done using natural rubber (NR), styrene-butadiene rubber (SBR) and whole tyre reclaim (WTR). The composites were prepared by melt mixing in an internal mixer at 170 oC. It was found that the optimum blend ratio was 85/15 for PS/NR, 90/10 for PS/SBR and 90/22 for PS/WTR blends. The effect of dynamic vulcanisation on 85/15 PS/NR and 90/10 PS/SBR blends using dicumyl peroxide (DCP) at various concentrations were also studied. The dynamic crosslinking improved the tensile properties, flexural properties, impact strength and dynamic mechanical properties of both the blends. The effect of unmodified and resorcinol formaldehyde latex (RFL)-coated short Nylon-6 fibres on the mechanical properties, morphology and dynamic mechanical properties of 85/15 PS/NR, 90/10 PS/SBR and 90/22 PS/WTR blends were studied. Fibre loading was varied from 0 to 3 wt.%. For 85/15 PS/NR blend, there was a significant enhancement in tensile properties, flexural properties and impact strength with 1 wt.% of both unmodified and RFL-coated fibres. Dynamic mechanical analysis revealed that the storage modulus at room temperature was maximum at 1 wt.% fiber loading for both composites. The surface functionality of the fiber was improved by giving alkali treatment. Maleic anhydride-grafted-polystyrene (MA-g-PS) was prepared and used as a compatibiliser. The effect of MA-g-PS on the composites was investigated with respect to mechanical properties, morphology and dynamic mechanical properties. The compatibiliser loading was varied from 0 to 2 wt.%. The properties were enhanced significantly in the case of treated and untreated fibre composites at a compatibiliser loading of 0.75 wt.%. SEM analysis confirmed better bonding between the fibre and the matrix. Dynamic mechanical studies showed that the storage modulus at room temperature improved for treated fibre composites in the presence of compatibiliser. In the case of 90/10 PS/SBR composites, the addition of short Nylon-6 fibres at 1 wt.% loading improved the tensile modulus, flexural properties and impact strength while the tensile strength was marginally reduced. The surface treated fibers along with compatibiliser at 0.5 wt.% improved the tensile properties, flexural properties and impact strength. DMA reveale that the storage modulus at room temperature was better for composites containing untreated fibre and the compatibiliser. In the case of 90/22 PS/WTR blends, 1 wt.% unmodified fibre and 0.5 wt.% RFL-coated fibres improved tensile modulus, flexural properties and impact strength. Tensile strength was improved marginally. The surface treatment of Nylon fibre and the addition of compatibiliser at 0.5 wt.% enhanced the tensile properties, flexural properties and impact strength. The dynamic mechanical analysis showed that the storage modulus at room temperature was better for untreated fibre composites in conjunction with the compatibiliser. The thermal stability of PS/NR was studied by TGA. Thermal stability of the blends improved with dynamic vulcanisation and with the incorporation of RFL-coated Nylon fibres. The untreated and partially hydrolyzed fibre composites in conjunction with the compatibiliser enhanced the thermal stability. Kinetic studies showed that the degradation of the blends and the composites followed first order kinetics.

Magnetic field effect on quantum corrections to the low-temperature conductivity in mettalic perovskite oxides

The transport and magnetotransport properties of the metallic and ferromagnetic SrRuO3 (SRO) and the metallic and paramagnetic LaNiO3 (LNO) epitaxial thin films have been investigated in fields up to 55 T at temperatures down to 1.8 K . At low temperatures both samples display a well-defined resistivity minimum. We argue that this behavior is due to the increasing relevance of quantum corrections to the conductivity (QCC) as temperature is lowered; this effect being particularly relevant in these oxides due to their short mean free path. However, it is not straightforward to discriminate between contributions of weak localization and renormalization of electron-electron interactions to the QCC through temperature dependence alone. We have taken advantage of the distinct effect of a magnetic field on both mechanisms to demonstrate that in ferromagnetic SRO the weak-localization contribution is suppressed by the large internal field leaving only renormalized electron-electron interactions, whereas in the nonmagnetic LNO thin films the weak-localization term is relevant.

“Studies on short polyester fiber - polyurethane elastomer composite with different interfacial bonding agents”

The work presented in this thesis is regarding the development and evaluation of new bonding agents for short polyester fiber - polyurethane elastomer composites. The conventional bonding system based on hexamethylenetetramine, resorcinol and hydrated silica was not effective as a bonding agent for the composite, as the water eliminated during the formation of the RF resin hydrolysed the urethane linkages. Four bonding agents based on MDI/'I‘DI and polypropyleneglycol, propyleneglycol and glycerol were prepared and the composite recipe was optimised with respect to the cure characteristics and mechanical properties. The flow properties, stress relaxation pattern and the thermal degradation characteristics of the composites containing different bonding agents were then studied in detail to evaluate the new bonding systems. The optimum loading of resin was 5 phr and the ratio of the -01 to isocyanate was 1:1. The cure characteristics showed that the optimum combination of cure rate and processability was given by the composite with the resin based on polypropyleneglycol/ glycerol/ 4,4’diphenylmethanediisocynate (PPG/GL/MDI). From the rheological studies of the composites with and without bonding agents it was observed that all the composites showed pseudoplastic nature and the activation energy of flow of the composite was not altered by the presence of bonding agents. Mechanical properties such as tensile strength, modulus, tear resistance and abrasion resistance were improved in the presence of bonding agents and the effect was more pronounced in the case of abrasion resistance. The composites based on MDI/GL showed better initial properties while composites with resins based on MDI/PPG showed better aging resistance. Stress relaxation showed a multistage relaxation behaviour for the composite. Within the-strain levels studied, the initial rate of relaxation was higher and the cross over time was lesser for the composite containing bonding agents. The bonding agent based on MDI/PPG/GL was found to be a better choice for improving stress relaxation characteristics with better interfacial bonding. Thennogravimetirc analysis showed that the presence of fiber and bonding agents improved the thennal stability of the polyurethane elastomer marginally and it was maximum in the case of MDI / GL based bonding agents. The kinetics of degradation was not altered by the presence of bonding agents

Immunostimulatory effect of a marine yeast Candida sake S165 in Fenneropenaeus indicus

The efficacy of a marine yeast Candida sake as source of immunostimulant to Indian white shrimp Fenneropenaeus indicus was estimated. Biomass of C. sake was prepared using malt extract agar and incorporated at graded levels into a standard diet to prepare yeast diets of varying biomass concentrations (1%, 10% and 20%). F. indicus were fed on these diets for a period of 28 days and challenged orally with white spot syndrome virus (WSSV) and immune parameters such as total haemocyte count, phenoloxidase and nitroblue tetrazolium reduction (NBT) were determined. Ten per cent C. sake in the diet was found to support an optimum immune response in the animals in general and their enhancement could be observed on the second and third day following challenge with the virus. The study has demonstrated that marine yeast C. sake at 10% in diet (w/w) may be used as an effective source of immunostimulants in F. indicus

3000 / futuristische Phantasmen und aktuelle Fantasien der Technokultur

Die Kernthese dieser Arbeit ist eine Leerstelle. Ihre Formulierung beruht auf einer Beobachtung, wie sie von William Gibson stammen könnte: kulturell avantgardistische Gruppen der Gesellschaft internalisieren für ihre technologisch gestützten Praktiken futuristische Phantasmen geschichtlicher Vorläufer, die in Literatur und Mediengeschichte detektivisch aufspürbar sind. Werden diese Verinnerlichungen in aktuelle Fantasien umgewandelt, entsteht eine hybride Mischung vielfältigster Beschäftigungen, Reflexionen und Entwürfe von Technokultur. Bringt man diese Kopplungen auf das Jahr 3000, die nächste epochale zukünftige Zäsur, wird die Absurdität des Projekts, Technokultur überhaupt zu thematisieren deutlich. Technokultur ist im dynamischen Wandel sozio-ikonografisch untersuchbar, wird aber durch Unschärferelation zum object trouvé und Triebmoment für eine in es selbst hinein assimilierbare Analyse. Der daraus folgenden Vermessenheit kann durch instrumentelle Serendipity begegnet werden, die hier nicht Effekt wäre, stattdessen als Methode Verwendung findet: Finden statt Suchen. Das verhältnismäßig neue Schreib/Lese-Medium Hypertext bietet sich dafür als geradezu prädestiniert an. Hypertext ist prinzipiell unabgeschlossen, er folgt hier Arbeitsprinzipien wie sie seit den frühen 1990ern in Online-Tagebüchern und seit den frühen 2000er Jahren in Weblogs (World Wide Web Logbooks) auszumachen sind: Notizen, Found Text (analog zu Found Footage), Zitate, Fragmente, die kurze Form, kurz: wissenschaftliche Alltagstextproduktion wird nach Ordnungskriterien a-systematisiert und verwoben - weniger archiviert denn gesammelt. Eine Art Second Hand Theorie entsteht.

Effects of post-harvest treatments on the carbohydrate composition of yacon roots in the Peruvian Andes

Yacon (Smallanthus sonchifolius [Poepp. & Endl.] H. Robinson) is an under-exploited native root crop of the Andes, which stores oligofructans (fructo-oligosaccharides, FOS) as its main component of dry matter (DM). FOS are of increasing economic interest because of their low caloric value in human diets and bifidogenic benefits on colon health. Two on-farm experiments were conducted to: (i) determine the effect of shaded, short-term storage at 1990 and 2930 m a.s.l. in the Andean highlands; and (ii) address the effects of a traditional sunlight exposure (‘sunning’) on the carbohydrate composition in the DM of tuberous yacon roots. After a 6-day shade storage FOS concentrations were smaller at the lower (36–48% of DM) than at the higher altitude (39–58% of DM). After 12 days FOS concentrations were nearly equal at both sites (27–39% of DM). The concentration of free sugars (fructose, glucose, sucrose) increased accordingly from 29–34 to 48–52%. During the 6-day sunning experiment FOS concentrations decreased from 50–62 to 29–44% and free sugars increased from 29–34 to 45–51%. The results indicate that partial hydrolysis of oligofructans starts shortly after harvest. Storage in highland environments should wherever possible exploit the cooler temperatures at higher altitudes. Sunning of yacon’s tuberous roots effectively reduces much of the roots’ water content, in this experiment 40%, and thus allows energy to be saved if yacon is processed into dehydrated products.