Estudo comparativo de dois conversores Boost quadrático com comutação suave monochaveados para aplicação de rastreamento de máxima potência em sistemas fotovoltaicos

This paper makes a comparative study of two Soft Single Switched Quadratic Boost Converters (SSS1 and SSS2) focused on Maximum Power Point Tracking (MPPT) of a PV array using Perturb and Observe (P&O) algorithm. The proposed converters maintain the static gain characteristics and dynamics of the original converter with the advantage of considerably reducing the switching losses and Electromagnetic Interference (EMI). It is displayed the input voltage Quadratic Boost converter modeling; qualitative and quantitative analysis of soft switching converters, defining the operation principles, main waveforms, time intervals and the state variables in each operation steps, phase planes of resonant elements, static voltage gain expressions, analysis of voltage and current efforts in semiconductors and the operational curves at 200 W to 800 W. There are presented project of PI, PID and PID + Notch compensators for MPPT closed-loop system and resonant elements design. In order to analyze the operation of a complete photovoltaic system connected to the grid, it was chosen to simulate a three-phase inverter using the P-Q control theory of three-phase instantaneous power. Finally, the simulation results and experimental with the necessary comparative analysis of the proposed converters will be presented.

Direct power control with common mode voltage elimination for open-winding brushless doubly-fed wind power generators

In this paper, a new open-winding control strategy is proposed for a brushless doubly-fed reluctance generator (BDFRG) applicable for wind turbines. The BDFRG control winding is fed via a dual two-level three-phase converter using a single dc bus. Direct power control based on maximum power point tracking with common mode voltage elimination is designed, which not only the active and reactive power is decoupled, but the reliability and redundancy are all improved greatly by increasing the switching modes of operation, while DC-link voltage and rating of power devices decreased by 50% comparing to the traditional three-level converter systems. Consequently its effectiveness is evaluated by simulation tests based on a 42-kW prototype generator.

Implementation of supply chain management theory in practice:a questionnaire survey in the United Kingdom

Purpose: The purpose of the research described in this paper is to disentangle the rhetoric from the reality in relation to supply chain management (SCM) adoption in practice. There is significant evidence of a divergence between theory and practice in the field of SCM. Research Approach: The authors’ review of the extant SCM literature highlighted a lack of replication studies in SCM, leading to the concept of refined replication being developed. The authors conducted a refined replication of the work of Sweeney et al. (2015) where a new SCM definitional construct – the Four Fundamentals – was proposed. The work presented in this article refines the previous study but adopts the same three-phase approach: focussed interviews, a questionnaire survey, and focus groups. This article covers the second phase of the refined replication study and describes an integrated research design of a questionnaire research to be undertaken in Britain. Findings and Originality: The article presents an integrated research design of a questionnaire research with emphases on the refined replication of previous work of Sweeney et al. (2015) carried out in Ireland and adapting it to the British context. Research Impact: The authors introduce the concept of refined replication in SCM research. This allows previous research to be built upon in order to test understanding of SCM theory and its practical implementation - based on the Four Fundamentals construct - among SCM professionals in Britain. Practical Impact: The article presents the integrated research design of a questionnaire research that may be used in similar studies.

A process evaluation of a cluster randomised trial to reduce potentially inappropriate prescribing in older people in primary care (OPTI-SCRIPT study)

Background
The OPTI-SCRIPT cluster randomised controlled trial (RCT) found that a three-phase multifaceted intervention including academic detailing with a pharmacist, GP-led medicines reviews, supported by web-based pharmaceutical treatment algorithms, and tailored patient information leaflets, was effective in reducing potentially inappropriate prescribing (PIP) in Irish primary care. We report a process evaluation exploring the implementation of the intervention, the experiences of those participating in the study and lessons for future implementation.

Methods
The OPTI-SCRIPT trial included 21 GP practices and 196 patients. The process evaluation used mixed methods. Quantitative data were collected from all GP practices and semi-structured interviews were conducted with GPs from intervention and control groups, and a purposive sample of patients from the intervention group. All interviews were transcribed verbatim and analysed using a thematic analysis.

Results
Despite receiving a standardised academic detailing session, intervention delivery varied among GP practices. Just over 70 % of practices completed medicines review as recommended with the patient present. Only single-handed practices conducted reviews without patients present, highlighting the influence of practice characteristics and resources on variation. Medications were more likely to be completely stopped or switched to another more appropriate medication when reviews were conducted with patients present. The patient information leaflets were not used by any of the intervention practices. Both GP (32 %) and patient (40 %) recruitment rates were modest. For those who did participate, overall, the experience was positively viewed, with GPs and patients referring to the value of medication reviews to improve prescribing and reduce unnecessary medications. Lack of time in busy GP practices and remuneration were identified as organisational barriers to future implementation.

Conclusions
The OPTI-SCRIPT intervention was positively viewed by both GPs and patients, both of whom valued the study’s objectives. Patient information leaflets were not a successful component of the intervention. Academic detailing and medication reviews are important components in changing PIP, and having patients present during the review process seems to be a more effective approach for decreasing PIP.

A literature review to Examine the Validity and Reliability of group poster presentations as an assessment method of a module in an undergraduate nursing degree programme

The introduction of a poster presentation as a formative assessment method over a multiple choice examination after the first phase of a three phase “health and well-being” module in an undergraduate nursing degree programme was greeted with a storm of criticism from fellow lecturers stating that poster presentations are not valid or reliable and totally irrelevant to the assessment of learning in the module. This paper seeks to investigate these criticisms by investigating the literature regarding producing nurses fit for practice, nurse curriculum development and wider nurse education, the purpose of assessment, validity and reliability to critically evaluate the poster presentation as a legitimate assessment method for these aims.

Optimal day-ahead scheduling of integrated urban energy systems

An optimal day-ahead scheduling method (ODSM) for the integrated urban energy system (IUES) is introduced, which considers the reconfigurable capability of an electric distribution network. The hourly topology of a distribution network, a natural gas network, the energy centers including the combined heat and power (CHP) units, different energy conversion devices and demand responsive loads (DRLs), are optimized to minimize the day-ahead operation cost of the IUES. The hourly reconfigurable capability of the electric distribution network utilizing remotely controlled switches (RCSs) is explored and discussed. The operational constraints from the unbalanced three-phase electric distribution network, the natural gas network, and the energy centers are considered. The interactions between the electric distribution network and the natural gas network take place through conversion of energy among different energy vectors in the energy centers. An energy conversion analysis model for the energy center was developed based on the energy hub model. A hybrid optimization method based on genetic algorithm (GA) and a nonlinear interior point method (IPM) is utilized to solve the ODSM model. Numerical studies demonstrate that the proposed ODSM is able to provide the IUES with an effective and economical day-ahead scheduling scheme and reduce the operational cost of the IUES.

Integrated Optimal Power Flow for Distribution Networks in Local and Urban Scales

This paper develops an integrated optimal power flow (OPF) tool for distribution networks in two spatial scales. In the local scale, the distribution network, the natural gas network, and the heat system are coordinated as a microgrid. In the urban scale, the impact of natural gas network is considered as constraints for the distribution network operation. The proposed approach incorporates unbalance three-phase electrical systems, natural gas systems, and combined cooling, heating, and power systems. The interactions among the above three energy systems are described by energy hub model combined with components capacity constraints. In order to efficiently accommodate the nonlinear constraint optimization problem, particle swarm optimization algorithm is employed to set the control variables in the OPF problem. Numerical studies indicate that by using the OPF method, the distribution network can be economically operated. Also, the tie-line power can be effectively managed.

Crystallization on the Mesoscale : Self-Assembly of Iron Oxide Nanocubes into Mesocrystals

Self-assembly of nanoparticles is a promising route to form complex, nanostructured materials with functional properties. Nanoparticle assemblies characterized by a crystallographic alignment of the nanoparticles on the atomic scale, i.e. mesocrystals, are commonly found in nature with outstanding functional and mechanical properties. This thesis aims to investigate and understand the formation mechanisms of mesocrystals formed by self-assembling iron oxide nanocubes. We have used the thermal decomposition method to synthesize monodisperse, oleate-capped iron oxide nanocubes with average edge lengths between 7 nm and 12 nm and studied the evaporation-induced self-assembly in dilute toluene-based nanocube dispersions. The influence of packing constraints on the alignment of the nanocubes in nanofluidic containers has been investigated with small and wide angle X-ray scattering (SAXS and WAXS, respectively). We found that the nanocubes preferentially orient one of their {100} faces with the confining channel wall and display mesocrystalline alignment irrespective of the channel widths.  We manipulated the solvent evaporation rate of drop-cast dispersions on fluorosilane-functionalized silica substrates in a custom-designed cell. The growth stages of the assembly process were investigated using light microscopy and quartz crystal microbalance with dissipation monitoring (QCM-D). We found that particle transport phenomena, e.g. the coffee ring effect and Marangoni flow, result in complex-shaped arrays near the three-phase contact line of a drying colloidal drop when the nitrogen flow rate is high. Diffusion-driven nanoparticle assembly into large mesocrystals with a well-defined morphology dominates at much lower nitrogen flow rates. Analysis of the time-resolved video microscopy data was used to quantify the mesocrystal growth and establish a particle diffusion-based, three-dimensional growth model. The dissipation obtained from the QCM-D signal reached its maximum value when the microscopy-observed lateral growth of the mesocrystals ceased, which we address to the fluid-like behavior of the mesocrystals and their weak binding to the substrate. Analysis of electron microscopy images and diffraction patterns showed that the formed arrays display significant nanoparticle ordering, regardless of the distinctive formation process.  We followed the two-stage formation mechanism of mesocrystals in levitating colloidal drops with real-time SAXS. Modelling of the SAXS data with the square-well potential together with calculations of van der Waals interactions suggests that the nanocubes initially form disordered clusters, which quickly transform into an ordered phase.

Representing Variability in Software Architecture

Software Architecture is a high level description of a software intensive system that enables architects to have a better intellectual control over the complete system. It is also used as a communication vehicle among the various system stakeholders. Variability in software-intensive systems is the ability of a software artefact (e.g., a system, subsystem, or component) to be extended, customised, or configured for deployment in a specific context. Although variability in software architecture is recognised as a challenge in multiple domains, there has been no formal consensus on how variability should be captured or represented. In this research, we addressed the problem of representing variability in software architecture through a three phase approach. First, we examined existing literature using the Systematic Literature Review (SLR) methodology, which helped us identify the gaps and challenges within the current body of knowledge. Equipped with the findings from the SLR, a set of design principles have been formulated that are used to introduce variability management capabilities to an existing Architecture Description Language (ADL). The chosen ADL was developed within our research group (ALI) and to which we have had complete access. Finally, we evaluated the new version of the ADL produced using two distinct case studies: one from the Information Systems domain, an Asset Management System (AMS); and another from the embedded systems domain, a Wheel Brake System (WBS). This thesis presents the main findings from the three phases of the research work, including a comprehensive study of the state-of-the-art; the complete specification of an ADL that is focused on managing variability; and the lessons learnt from the evaluation work of two distinct real-life case studies.

Modélisation des machines par circuits couplés pour l’observation des courants de barres au rotor

Ce travail présente une modélisation rapide d’ordre élévé capable de modéliser une configuration rotorique en cage complète ou en grille, de reproduire les courants de barre et tenir compte des harmoniques d’espace. Le modèle utilise une approche combinée d’éléments finis avec les circuits-couplés. En effet, le calcul des inductances est réalisé avec les éléments finis, ce qui confère une précision avancée au modèle. Cette méthode offre un gain important en temps de calcul sur les éléments finis pour des simulations transitoires. Deux outils de simulation sont développés, un dans le domaine du temps pour des résolutions dynamiques et un autre dans le domaine des phaseurs dont une application sur des tests de réponse en fréquence à l’arrêt (SSFR) est également présentée. La méthode de construction du modèle est décrite en détail de même que la procédure de modélisation de la cage du rotor. Le modèle est validé par l’étude de machines synchrones: une machine de laboratoire de 5.4 KVA et un grand alternateur de 109 MVA dont les mesures expérimentales sont comparées aux résultats de simulation du modèle pour des essais tels que des tests à vide, des courts-circuits triphasés, biphasés et un test en charge.

Investigating wetting characteristics on microstructured surfaces for superhydrophobicity and metal microcasting

The engineering of liquid behavior on surfaces is important for infrastructure, transportation, manufacturing, and sensing. Surfaces can be rendered superhydrophobic by microstructuring, and superhydrophobic devices could lead to practical corrosion inhibition, self-cleaning, fluid flow control, and surface drag reduction. To more fully understand how liquid interacts with microstructured surfaces, this dissertation introduces a direct method for determining droplet solid-liquid-vapor interfacial geometry on microstructured surfaces. The technique performs metrology on molten metal droplets deposited onto microstructured surfaces and then frozen. Unlike other techniques, this visualization technique can be used on large areas of curved and opaque microstructured surfaces to determine contact line. This dissertation also presents measurements and models for how curvature and flexing of microstructured polymers affects hydrophobicity. Increasing curvature of microstructured surfaces leads to decreased slide angle for liquid droplets suspended on the surface asperities. For a surface with regularly spaced asperities, as curvature becomes more positive, droplets suspended on the tops of asperities are suspended on fewer asperities. Curvature affects superhydrophobicity because microscopic curvature changes solid-liquid interaction, pitch is altered, and curvature changes the shape of the three phase contact line. This dissertation presents a model of droplet interactions with curved microstructured surfaces that can be used to design microstructure geometries that maintain the suspension of a droplet when curved surfaces are covered with microstructured polymers. Controlling droplet dynamics could improve microfluidic devices and the shedding of liquids from expensive equipment, preventing corrosion and detrimental performance. This dissertation demonstrates redirection of dynamic droplet spray with anisotropic microstructures. Superhydrophobic microstructured surfaces can be economically fabricated using metal embossing masters, so this dissertation describes casting-based microfabrication of metal microstructures and nanostructures. Low melting temperature metal was cast into flexible silicone molds which were themselves cast from microfabricated silicon templates. The flexibility of the silicone mold permits casting of curved surfaces, which this dissertation demonstrates by fabricating a cylindrical metal roller with microstructures. The metal microstructures can be in turn used as a reusable molding tool. This dissertation also describes an industrial investment casting process to produce aluminum molds having integrated microstructures. Unlike conventional micromolding tools, the aluminum mold was large and had complex curved surfaces. The aluminum was cast into curved microstructured ceramic molds which were themselves cast from curved microstructured rubber. Many structures were successfully cast into the aluminum with excellent replication fidelity, including circular, square, and triangular holes. This dissertation demonstrates molding of large, curved surfaces having surface microstructures using the aluminum mold. This work contributes a more full understanding of the phenomenon of superhydrophobicity and techniques for the economic fabrication of superhydrophobic microstructures.

A Sense of Wonder: Enhancing Access to Folktales through Task and Facet Analysis

Discusses the approach taken in Phase 1 of a three-phase project Folktales, Facets and FRBR [funded by a grant from OCLC/ALISE]. This project works with the special collection of folktales at the Center for Children’s Books (CCB) at the University of Illinois at Urbana-Champaign, and the scholars who use this collection. The project aims to enhance the effectiveness and efficiency of folktale access through deep understanding of user needs. Phase 1 included facet analysis of the bibliographic records for a sample of 100 folktale books in the CCB, and task analysis of interviews with four CCB-affiliated faculty. Describes the information tasks, information seeking obstacles, and desired features for a discovery and access tool related to folktales for this initial group of scholarly users of folktales.

Redução dos níveis de Ocratoxina A por ação da enzima peroxidase

A ocratoxina A é um composto formado a partir do metabolismo secundário de fungos dos gêneros Aspergillus e Penicillium. Uma vez que a presença dessa micotoxina nos alimentos causa sérios danos à saúde humana e animal, surge o interesse pelo desenvolvimento de métodos que visem a redução dos seus níveis em diferentes matrizes. Diversos processos de descontaminação têm sido propostos, sendo que os métodos de redução biológica tem recebido destaque. Esses métodos consistem na aplicação de micro-organismos ou de suas enzimas, o que gera a biotransformação ou degradação da toxina produzindo metabólitos com menor ou nenhuma toxicidade. Diante disso, o objetivo geral do trabalho foi avaliar o efeito da peroxidase na redução dos níveis de ocratoxina A. As enzimas peroxidases testadas foram a comercial e a obtida do farelo de arroz. Para a extração enzimática foram utilizadas as frações granulométricas do farelo de arroz de 48 a 100 mesh, sendo estas frações caracterizadas quimicamente. A peroxidase foi extraída do farelo de arroz em tampão 10 mM pH 5,0 e purificada por partição trifásica, obtendo 77,1% de recuperação e 9,2 para o fator de purificação. O método utilizado para a extração da ocratoxina A do sistema aquoso foi por partição líquido-líquido utilizando como solvente o clorofórmio, sendo esse método validado segundo os parâmetros de linearidade (0,1 a 20 ng mL-1), coeficientes de correlação (0,9997) e de determinação (0,9994), e limites de detecção (0,02) e quantificação (0,03). A afinidade entre as peroxidases e a ocratoxina A foi verificada segundo os parâmetros de KM e Vmáx, resultando em 0,00027 mM e 0,000015 mM min-1, respectivamente, para a peroxidase comercial, e 0,0065 mM e 0,000031 mM min-1 para a obtida do farelo de arroz. Com relação aos percentuais de redução de ocratoxina A, foram avaliadas 3 proporções enzima:substrato (1:10, 1:5 e 8:1 para a comercial e 1:10, 1:5 e a com atividade de 0,063 U mL-1 para a do farelo), sendo que as proporções que forneceram maior redução foi a de 8:1 para a enzima comercial (0,063 U mL-1) e a correspondente a 0,063 U mL-1 para a enzima obtida do farelo. Os percentuais de redução de ocratoxina A foram de 59% para a peroxidase comercial em 300 min e 41% para a peroxidase do farelo de arroz em 1440 min. O efeito de adsorção da ocratoxina A pela enzima peroxidase foi descartado uma vez que foi realizada a sua hidrólise com a enzima pepsina e verificado um percentual de 2,7% de adsorção, demonstrando que a redução foi por ação enzimática. A enzima obtida de farelo de arroz com atividade de 0,063 U mL-1 foi aplicada em suco de uva tinto e branco. Observou-se que para o primeiro não houve redução significativa, enquanto que para o segundo a redução foi de 17%. Neste trabalho, então, foi possível verificar a capacidade de redução dos níveis da ocratoxina A pela enzima peroxidase, tanto em sistema aquoso como no suco de uva integral branco.

Sistema de armazenamento de energia com base em baterias e no ondulador de tensão trifásico

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica Ramo de Automação e Eletrotécnica Ramo de Automação e Eletrónica Industrial

Dynamically balanced and plausible trajectory planning for human-like characters

International audience