An Adjustable Compliant Joint for Lower-Limb Exoskeletons

The field of exoskeletons and wearable devices for walking assistance and rehabilitation has advanced considerably over the past few years. Currently, commercial devices contain joints with stiff actuators that cannot adapt to unpredictable environments. These actuators consume more energy and may not be appropriate for human-machine interactions. Thus, adjustable compliant actuators are being cautiously incorporated into new exoskeletons and active orthoses. Some simulation-based studies have evaluated the benefits of incorporating compliant joints into such devices. Another reason that compliant actuators are desirable is that spasticity and spasmodic movements are common among patients with motor deficiencies; compliant actuators could efficiently absorb these perturbations and improve joint control. In this paper, we provide an overview of the requirements that must be fulfilled by these actuators while evaluating the behavior of leg joints in the locomotion cycle. A brief review of existing compliant actuators is conducted, and our proposed variable stiffness actuator prototype is presented and evaluated. The actuator prototype is implemented in an exoskeleton knee joint operated by a state machine that exploits the dynamics of the leg, resulting in a reduction in actuation energy demand and better adaptability to disturbances.

Systematic Process for Building a Fault Diagnoser Based on Petri Nets Applied to a Helicopter

This work presents a systematic process for building a Fault Diagnoser (FD), based on Petri Nets (PNs) which has been applied to a small helicopter. This novel tool is able to detect both intermittent and permanent faults. The work carried out is discussed from theoretical and practical point of view. The procedure begins with a division of the whole system into subsystems, which are the devices that have to be modeled by using PN, considering both the normal and fault operations. Subsequently, the models are integrated into a global Petri Net diagnoser (PND) that is able to monitor a whole helicopter and show critical variables to the operator in order to determine the UAV health, preventing accidents in this manner. A Data Acquisition System (DAQ) has been designed for collecting data during the flights and feeding PN diagnoser with them. Several real flights (nominal or under failure) have been carried out to perform the diagnoser setup and verify its performance. A summary of the validation results obtained during real flight tests is also included. An extensive use of this tool will improve preventive maintenance protocols for UAVs (especially helicopters) and allow establishing recommendations in regulations

A friendly online C compiler to improve programming skills based on student self-assessment

This paper presents an online C compiler designed so that students can program their practical assignments in Programming courses. What is really innovative is the self-assessment of the exercises based on black-box tests and train students’ skill to test software. Moreover, this tool lets instructors, not only proposing and classifying practical exercises, but also evaluating automatically the efforts dedicated and the results obtained by the students. The system has been applied to the 1st-year students at the Industrial Engineering specialization at the Universidad Politecnica de Madrid. Results show that the students obtained better academic performance, reducing the failure rate in the practical exam considerably with respect to previous years, in addition that an anonymous survey proved that students are satisfied with the system because they get instant feedback about their programs.

Detecting, Localizing and Following Dynamic Objects with a Mini-UAV

This paper presents an approach for the detection, localization and following of dynamic terrestrial objects using a mini-UAV. The development is intended to be used for surveillance of large infrastructures. The detection algorithm is based on finding several pre-defined characteristics of the target, such as color, shape and size. The process used to localize the target, once it is detected, is based on an inversion of the Pinhole camera model. The task of following the Summit XL was designed to keep the target inside the field of view of the camera, and it was implemented in the form of a PID controller. The system has been tested both in simulation and with real robots, showing promising results.

Multiple Robots, Single Operator: Considerations About Information And Commanding

Multiple robot, single operator scenarios suppose a challenge in terms of human factors. Two relevant issues are keeping the situational awareness and managing the workload of operators. In order to address these problems, this work analyses the management of information and commands in multi-robot missions. About the information, this paper proposes a selection based on mission and operator states. Regarding the commands, this work reflects about the levels of automation and the methods of commanding.

Multi-UAV Coordination and Control Interface

The interest in missions with multiple Unmanned Aerial Vehicles (UAVs) has increased significantly in last years. These missions take advantage of the use of fleets instead of single UAVs to ensure the success, reduce the duration or increase the goals of the mission. In addition, they allow performing tasks that require multiple agents and certain coordination (e.g. surveillance of large areas or transport of heavy loads). Nevertheless, these missions suppose a challenge in terms of control and monitoring. In fact, the workload of the operators rises with the utilization of multiple UAVs and payloads, since they have to analyze more information, make more decisions and generate more commands during the mission. This work addresses the operator workload problem in multi-UAV missions by reducing and selecting the information. Two approaches are considered: a first one that selects the information according to the mission state, and a second one that selects it according to the operator preferences. The result is an interface that is able to control the amount of information and show what is relevant for mission and operator at the time.

Development of a sensorimotor algorithm able to deal with unforeseen pushes and its implementation based on VHDL

Development of a Sensorimotor Algorithm Able to Deal with Unforeseen Pushes and Its Implementation Based on VHDL is the title of my thesis which concludes my Bachelor Degree in the Escuela Técnica Superior de Ingeniería y Sistemas de Telecomunicación of the Universidad Politécnica de Madrid. It encloses the overall work I did in the Neurorobotics Research Laboratory from the Beuth Hochschule für Technik Berlin during my ERASMUS year in 2015. This thesis is focused on the field of robotics, specifically an electronic circuit called Cognitive Sensorimotor Loop (CSL) and its control algorithm based on VHDL hardware description language. The reason that makes the CSL special resides in its ability to operate a motor both as a sensor and an actuator. This way, it is possible to achieve a balanced position in any of the robot joints (e.g. the robot manages to stand) without needing any conventional sensor. In other words, the back electromotive force (EMF) induced by the motor coils is measured and the control algorithm responds depending on its magnitude. The CSL circuit contains mainly an analog-to-digital converter (ADC) and a driver. The ADC consists on a delta-sigma modulation which generates a series of bits with a certain percentage of 1's and 0's, proportional to the back EMF. The control algorithm, running in a FPGA, processes the bit frame and outputs a signal for the driver. This driver, which has an H bridge topology, gives the motor the ability to rotate in both directions while it's supplied with the power needed. The objective of this thesis is to document the experiments and overall work done on push ignoring contractive sensorimotor algorithms, meaning sensorimotor algorithms that ignore large magnitude forces (compared to gravity) applied in a short time interval on a pendulum system. This main objective is divided in two sub-objectives: (1) developing a system based on parameterized thresholds and (2) developing a system based on a push bypassing filter. System (1) contains a module that outputs a signal which blocks the main Sensorimotor algorithm when a push is detected. This module has several different parameters as inputs e.g. the back EMF increment to consider a force as a push or the time interval between samples. System (2) consists on a low-pass Infinite Impulse Response digital filter. It cuts any frequency considered faster than a certain push oscillation. This filter required an intensive study on how to implement some functions and data types (fixed or floating point data) not supported by standard VHDL packages. Once this was achieved, the next challenge was to simplify the solution as much as possible, without using non-official user made packages. Both systems behaved with a series of interesting advantages and disadvantages for the elaboration of the document. Stability, reaction time, simplicity or computational load are one of the many factors to be studied in the designed systems. RESUMEN. Development of a Sensorimotor Algorithm Able to Deal with Unforeseen Pushes and Its Implementation Based on VHDL es un Proyecto de Fin de Grado (PFG) que concluye mis estudios en la Escuela Técnica Superior de Ingeniería y Sistemas de Telecomunicación de la Universidad Politécnica de Madrid. En él se documenta el trabajo de investigación que realicé en el Neurorobotics Research Laboratory de la Beuth Hochschule für Technik Berlin durante el año 2015 mediante el programa de intercambio ERASMUS. Este PFG se centra en el campo de la robótica y en concreto en un circuito electrónico llamado Cognitive Sensorimotor Loop (CSL) y su algoritmo de control basado en lenguaje de modelado hardware VHDL. La particularidad del CSL reside en que se consigue que un motor haga las veces tanto de sensor como de actuador. De esta manera es posible que las articulaciones de un robot alcancen una posición de equilibrio (p.ej. el robot se coloca erguido) sin la necesidad de sensores en el sentido estricto de la palabra. Es decir, se mide la propia fuerza electromotriz (FEM) inducida sobre el motor y el algoritmo responde de acuerdo a su magnitud. El circuito CSL se compone de un convertidor analógico-digital (ADC) y un driver. El ADC consiste en un modulador sigma-delta, que genera una serie de bits con un porcentaje de 1's y 0's determinado, en proporción a la magnitud de la FEM inducida. El algoritmo de control, que se ejecuta en una FPGA, procesa esta cadena de bits y genera una señal para el driver. El driver, que posee una topología en puente H, provee al motor de la potencia necesaria y le otorga la capacidad de rotar en cualquiera de las dos direcciones. El objetivo de este PFG es documentar los experimentos y en general el trabajo realizado en algoritmos Sensorimotor que puedan ignorar fuerzas de gran magnitud (en comparación con la gravedad) y aplicadas en una corta ventana de tiempo. En otras palabras, ignorar empujones conservando el comportamiento original frente a la gravedad. Para ello se han desarrollado dos sistemas: uno basado en umbrales parametrizados (1) y otro basado en un filtro de corte ajustable (2). El sistema (1) contiene un módulo que, en el caso de detectar un empujón, genera una señal que bloquea el algoritmo Sensorimotor. Este módulo recibe diferentes parámetros como el incremento necesario de la FEM para que se considere un empujón o la ventana de tiempo para que se considere la existencia de un empujón. El sistema (2) consiste en un filtro digital paso-bajo de respuesta infinita que corta cualquier variación que considere un empujón. Para crear este filtro se requirió un estudio sobre como implementar ciertas funciones y tipos de datos (coma fija o flotante) no soportados por las librerías básicas de VHDL. Tras esto, el objetivo fue simplificar al máximo la solución del problema, sin utilizar paquetes de librerías añadidos. En ambos sistemas aparecen una serie de ventajas e inconvenientes de interés para el documento. La estabilidad, el tiempo de reacción, la simplicidad o la carga computacional son algunas de las muchos factores a estudiar en los sistemas diseñados. Para concluir, también han sido documentadas algunas incorporaciones a los sistemas: una interfaz visual en VGA, un módulo que compensa el offset del ADC o la implementación de una batería de faders MIDI entre otras.

Prospectives of monitoring biological activity in a red-legged partridge incubator with a carbon dioxide probe

This study focuses on the relationship between CO2 production and the ultimate hatchability of the incubation. A total amount of 43316 eggs of red-legged partridge (Alectoris rufa) were supervised during five actual incubations: three in 2012 and two in 2013. The CO2 concentration inside the incubator was monitored over a 20-day period, showing sigmoidal growth from ambient level (428 ppm) up to 1700 ppm in the incubation with the highest hatchability. Two sigmoid growth models (logistic and Gompertz) were used to describe the CO2 production by the eggs, with the result that the logistic model was a slightly better fit (r2=0.976 compared to r2=0.9746 for Gompertz). A coefficient of determination of 0.997 between the final CO2 estimation (ppm) using the logistic model and hatchability (%) was found.

A Reliable Open-Source System Architecture for the Fast Designing and Prototyping of Autonomous Multi-UAV Systems: Simulation and Experimentation

During the process of design and development of an autonomous Multi-UAV System, two main problems appear. The first one is the difficulty of designing all the modules and behaviors of the aerial multi-robot system. The second one is the difficulty of having an autonomous prototype of the system for the developers that allows to test the performance of each module even in an early stage of the project. These two problems motivate this paper. A multipurpose system architecture for autonomous multi-UAV platforms is presented. This versatile system architecture can be used by the system designers as a template when developing their own systems. The proposed system architecture is general enough to be used in a wide range of applications, as demonstrated in the paper. This system architecture aims to be a reference for all designers. Additionally, to allow for the fast prototyping of autonomous multi-aerial systems, an Open Source framework based on the previously defined system architecture is introduced. It allows developers to have a flight proven multi-aerial system ready to use, so that they can test their algorithms even in an early stage of the project. The implementation of this framework, introduced in the paper with the name of “CVG Quadrotor Swarm”, which has also the advantages of being modular and compatible with different aerial platforms, can be found at https://​github.​com/​Vision4UAV/​cvg_​quadrotor_​swarm with a consistent catalog of available modules. The good performance of this framework is demonstrated in the paper by choosing a basic instance of it and carrying out simulation and experimental tests whose results are summarized and discussed in this paper.

A Vision-based Quadrotor Multi-robot Solution for the Indoor Autonomy Challenge of the 2013 International Micro Air Vehicle Competition

This paper presents a completely autonomous solution to participate in the Indoor Challenge of the 2013 International Micro Air Vehicle Competition (IMAV 2013). Our proposal is a multi-robot system with no centralized coordination whose robotic agents share their position estimates. The capability of each agent to navigate avoiding collisions is a consequence of the resulting emergent behavior. Each agent consists of a ground station running an instance of the proposed architecture that communicates over WiFi with an AR Drone 2.0 quadrotor. Visual markers are employed to sense and map obstacles and to improve the pose estimation based on Inertial Measurement Unit (IMU) and ground optical flow data. Based on our architecture, each robotic agent can navigate avoiding obstacles and other members of the multi-robot system. The solution is demonstrated and the achieved navigation performance is evaluated by means of experimental flights. This work also analyzes the capabilities of the presented solution in simulated flights of the IMAV 2013 Indoor Challenge. The performance of the CVG UPM team was awarded with the First Prize in the Indoor Autonomy Challenge of the IMAV 2013 competition.

Pedestrian Motion Prediction: A Graph Based Approach

A novel pedestrian motion prediction technique is presented in this paper. Its main achievement regards to none previous observation, any knowledge of pedestrian trajectories nor the existence of possible destinations is required; hence making it useful for autonomous surveillance applications. Prediction only requires initial position of the pedestrian and a 2D representation of the scenario as occupancy grid. First, it uses the Fast Marching Method (FMM) to calculate the pedestrian arrival time for each position in the map and then, the likelihood that the pedestrian reaches those positions is estimated. The technique has been tested with synthetic and real scenarios. In all cases, accurate probability maps as well as their representative graphs were obtained with low computational cost.

Método de estimativa de torque da articulação do joelho baseada em EMG

Este trabalho apresenta um método de estimativa de torque do joelho baseado em sinais eletromiográficos (EMG) durante terapia de reabilitação robótica. Os EMGs, adquiridos de cinco músculos envolvidos no movimento de flexão e extensão do joelho, são processados para encontrar as ativações musculares. Em seguida, mediante um modelo simples de contração muscular, são calculadas as forças e, usando a geometria da articulação, o torque do joelho. As funções de ativação e contração musculares possuem parâmetros limitados que devem ser calibrados para cada usuário, sendo o ajuste feito mediante a minimização do erro entre o torque estimado e o torque medido na articulação usando a dinâmica inversa. São comparados dois métodos iterativos para funções não-lineares como técnicas de otimização restrita para a calibração dos parâmetros: Gradiente Descendente e Quasi-Newton. O processamento de sinais, calibração de parâmetros e cálculo de torque estimado foram desenvolvidos no software MATLAB®; o cálculo de torque medido foi feito no software OpenSim com sua ferramenta de dinâmica inversa.

Análise de grandezas cinemáticas e dinâmicas inerentes à hemiparesia através da descoberta de conhecimento em bases de dados

Em virtude de uma elevada expectativa de vida mundial, faz-se crescente a probabilidade de ocorrer acidentes naturais e traumas físicos no cotidiano, o que ocasiona um aumento na demanda por reabilitação. A terapia física, sob o paradigma da reabilitação robótica com serious games, oferece maior motivação e engajamento do paciente ao tratamento, cujo emprego foi recomendado pela American Heart Association (AHA), apontando a mais alta avaliação (Level A) para pacientes internados e ambulatoriais. No entanto, o potencial de análise dos dados coletados pelos dispositivos robóticos envolvidos é pouco explorado, deixando de extrair informações que podem ser de grande valia para os tratamentos. O foco deste trabalho consiste na aplicação de técnicas para descoberta de conhecimento, classificando o desempenho de pacientes diagnosticados com hemiparesia crônica. Os pacientes foram inseridos em um ambiente de reabilitação robótica, fazendo uso do InMotion ARM, um dispositivo robótico para reabilitação de membros superiores e coleta dos dados de desempenho. Foi aplicado sobre os dados um roteiro para descoberta de conhecimento em bases de dados, desempenhando pré-processamento, transformação (extração de características) e então a mineração de dados a partir de algoritmos de aprendizado de máquina. A estratégia do presente trabalho culminou em uma classificação de padrões com a capacidade de distinguir lados hemiparéticos sob uma precisão de 94%, havendo oito atributos alimentando a entrada do mecanismo obtido. Interpretando esta coleção de atributos, foi observado que dados de força são mais significativos, os quais abrangem metade da composição de uma amostra.

Método de desvio de obstáculos aplicado em veículo autônomo.

A operação de veículos autônomos necessita de meios para evitar colisões quando obstáculos não conhecidos previamente são interpostos em sua trajetória. Algoritmos para executar o desvio e sensores apropriados para a detecção destes obstáculos são essenciais para a operação destes veículos. Esta dissertação apresenta estudos sobre quatro algoritmos de desvio de obstáculos e tecnologia de três tipos de sensores aplicáveis à operação de veículos autônomos. Após os estudos teóricos, um dos algoritmos foi testado para a comprovação da aplicabilidade ao veículo de teste. A etapa experimental foi a realização de um programa, escrito em linguagem de programação Java, que aplicou o algoritmo Inseto 2 para o desvio de obstáculos em uma plataforma robótica (Robodeck) com o uso de sensores ultrassônicos embarcados na referida plataforma. Os experimentos foram conduzidos em ambiente fechado (indoor), bidimensional e horizontal (plano), fazendo o Robodeck executar uma trajetória. Para os testes, obstáculos foram colocados para simular situações variadas e avaliar a eficácia do algoritmo nestas configurações de caminho. O algoritmo executou o desvio dos obstáculos com sucesso e, quando havia solução para a trajetória, ela foi encontrada. Quando não havia solução, o algoritmo detectou esta situação e parou o veículo.

Modelagem e controle de marcha de robôs bípedes com disco de inércia.

Esta tese trata de um robô bípede em caminhar dinâmico. Neste robô, que normalmente é um sistema sub-atuado, fazemos uso de um disco de inércia que funciona num certo sentido como um atuador adicional. Através deste disco, obtém-se mais liberdade para a elaboração de passos repetitivos e um aumento na robustez. Por outro lado, o sistema de controle dos passos deve controlar, além do passo propriamente dito, também a velocidade do disco, de modo que não sejam saturados os atuadores (motores elétricos). Apresentamos então um controlador capaz de realizar estas ações simultaneamente.