Experiments in gear configuration to reduce bycatch in an estuarine squid-trawl fishery

Three experiments were performed in an estuarine squid-trawl fishery in New South Wales, Australia, to test modifications to trawl nets. Lateral mesh openings were experimentally increased and physical bycatch reduction devices (BRDs) were placed in codends. These modifications aimed to reduce nontargeted catches of fish, while maintaining catches of the targeted broad squid (Photololigo etheridgei) and bottle squid (Loliolus noctiluca). Compared to conventional codends made with 41-mm diamond mesh, codends made with different posterior circumferences and larger 45-mm mesh had no significant effect on the catches of any species. The best performing configurations involved the installation of BRDs designed to separate organisms according to differences in behavior. In particular, versions of a composite square-mesh panel reduced the total weight of bycatch by up to 71% and there was no significant effect on the catches of squid. The results are discussed in terms of the probable differences in behavior between fish and squid in codends. After this study, a square-mesh panel BRD was voluntarily adopted throughout the fishery.

Composite beta-AgVO3@V5+1.6V4+0.4O4.8 hydrogels and xerogels for catalytic applications

Comunicación (Poster) en panel del congreso: Designing New Heterogeneous Catalysts, Faraday Discussion, 4–6 April 2016. London, United Kingdom.

Sensitivity of wear rates in the micro-scale abrasion test to test conditions and material hardness

Micro-scale abrasion (ball cratering) tests were performed with different combinations of ball and bulk specimen materials, under different test conditions, such as load and abrasive slurry concentration. Wear modes were classified into two types: with rolling particle motion and with grooving particle motion. Wear rates observed with rolling particle motion were relatively insensitive to test conditions, whereas with grooving motion they varied much more. It is suggested that rolling abrasion is therefore a more appropriate mode if reproducible test results are desired. The motion of the abrasive particles can be reliably predicted from the knowledge of hardnesses and elastic properties of the ball and the specimen, and from the normal load and the abrasive slurry concentration. General trends in wear resistance measured in the micro-scale abrasion test with rolling particle motion are similar to those reported in tests with fixed abrasives with sliding particle motion, although the variation in wear resistance with hardness is significantly smaller. © 2004 Published by Elsevier B.V.

Sources of variability in the free-ball micro-scale abrasion test

In the 'free-ball' version of the micro-scale abrasion or ball-cratering test the rotating ball rests against a tilted sample and a grooved drive shaft. Tests under nominally identical conditions with different apparatus commonly show small but significant differences in measured wear rate. An indirect method has been developed and demonstrated for continuous on-line measurement of the coefficient of friction in the free-ball test. Experimental investigation of the effects of sample tilt angle and drive shaft groove width shows that both these factors influence the stability of the rotation of the ball, and the shape of the abrasive slurry pool, which in turn affect the coefficient of friction in the wear scar area and the measured wear rate. It is suggested that in order to improve the reproducibility of this method the geometry of the apparatus should be specified. For the apparatus used in this work with a steel ball of 25 mm diameter, a sample tilt angle of 60-75° and a shaft groove width of about 10mm provided the most stable ball motion and a wear rate which showed least variability. © 2004 Elsevier B.V. All rights reserved.

Evaluation of a Pound Net Leader Designed to Reduce Sea Turtle Bycatch

Offshore pound net leaders in the southern portion of Chesapeake Bay in Virginia waters were documented to incidentally take protected loggerhead, Caretta caretta, and Kemp’s ridley, Lepidochelys kempii, sea turtles. Because of these losses, NOAA’s National Marine Fisheries Service (NMFS) in 2004 closed the area to offshore pound net leaders annually from 6 May to 15 July and initiated a study of an experimental leader design that replaced the top two-thirds of the traditional mesh panel leader with vertical ropes (0.95 cm) spaced 61 cm apart. This experimental leader was tested on four pound net sites on the eastern shore of Chesapeake Bay in 2004 and 2005. During the 2 trial periods, 21 loggerhead and Kemp’s ridley sea turtles were found interacting with the control leader and 1 leatherback turtle, Dermochelys coriacea, was found interacting with the experimental leader. Results of a negative binomial regression analysis comparing the two leader designs found the experimental leader significantly reduced sea turtle interactions (p=0.03). Finfish were sampled from the pound nets in the study to assess finfish catch performance differences between the two leader designs. Although the conclusions from this element of the experiment are not robust, paired t-test and Wilcoxon signed rank test results determined no significant harvest weight difference between the two leaders. Kolmogorov-Smirnov tests did not reveal any substantive size selectivity differences between the two leaders.