Brake system performance requirements of a lightweight electric/hybrid rear wheel drive vehicle

Investigates the braking performance requirements of the UltraCommuter, a lightweight series hybrid electric vehicle currently under development at the University of Queensland. With a predicted vehicle mass of 600 kg and two in-wheel motors each capable of 500 Nm of peak torque, decelerations up to 0.46 g are theoretically possible using purely regenerative braking. With 99% of braking demands less than 0.35 g, essentially all braking can be regenerative. The wheel motors have sufficient peak torque capability to lock the rear wheels in combination with front axle braking, eliminating the need for friction braking at the rear. Emergency braking levels approaching 1 g are achieved by supplementation with front disk brakes. This paper presents equations describing the peak front and rear axle braking forces which occur under straight line braking, including gradients. Conventionally, to guarantee stability, mechanical front/rear proportioning of braking effort ensures that the front axle locks first. In this application, all braking is initially regenerative at the rear, and an adaptive ''by-wire'' proportioning system presented ensures this stability requirement is still satisfied. Front wheel drive and all wheel drive systems are also discussed. Finally, peak and continuous performance measures, not commonly provided for friction brakes, are derived for the UltraCommuter's motor capability and range of operation.

A method of switch selection for an electric vehicle drive

The key to reducing cost of electric vehicles is integration. All too often systems such as the motor, motor controller, batteries and vehicle chassis/body are considered as separate problems. The truth is that a lot of trade-offs can be made between these systems, causing an overall improvement in many areas including total cost. Motor controller and battery cost have a relatively simple relationship; the less energy lost in the motor controller the less energy that has to be carried in the batteries, hence the lower the battery cost. A motor controller’s cost is primarily influenced by the cost of the switches. This paper will therefore present a method of assessing the optimal switch selection on the premise that the optimal switch is the one that produces the lowest system cost, where system cost is the cost of batteries + switches.

On-road driving studies to understand why drivers behave as they do at regional rail level crossings

Improving safety at rail level crossings is an important part of both road and rail safety strategies. While low in number, crashes between vehicles and trains at level crossings are catastrophic events typically involving multiple fatalities and serious injuries. Advances in driving assessment methods, such as the provision of on-road instrumented test vehicles with eye and head tracking, provide researchers with the opportunity to further understand driver behaviour at such crossings in ways not previously possible. This paper describes a study conducted to further understand the factors that shape driver behaviour at rail level crossings using instrumented vehicles. Twenty-two participants drove an On-Road Test Vehicle (ORTeV) on a predefined route in regional Victoria with a mix of both active (flashing lights with/without boom barriers) and passively controlled (stop, give way) crossings. Data collected included driving performance data, head checks, and interview data to capture driver strategies. The data from an integrated suite of methods demonstrated clearly how behaviour differs at active and passive level crossings, particularly for inexperienced drivers. For example, the head check data clearly show the reliance and expectancies of inexperienced drivers for active warnings even when approaching passively controlled crossings. These studies provide very novel and unique insights into how level crossing design and warnings shape driver behaviour.

Characteristics of police-reported road traffic crashes in Ethiopia over a six year period

Ethiopia has one of Africa’s fastest growing non-oil producing economies and an increasing level of motorisation (AfDB, OECD, UNDP, & UNECA, 2012). This rapidly increasing mobility has created some unique road safety concerns; however there is scant published information and related commentary (United Nations Economic Commission for Africa, 2009). The objective of this paper is to quantify police-reported traffic crashes in Ethiopia and characterise the existing state of road safety. Six years (July 2005 - June 2011) of police-reported crash data were analysed, consisting of 12,140 fatal and 29,454 injury crashes on the country’s road network. The 12,140 fatal crashes involved 1,070 drivers, 5,702 passengers, and 7,770 pedestrians, totalling 14,542 fatalities, an average of 1.2 road user fatalities per crash. An important and glaring trend that emerges is that more than half of the fatalities in Ethiopia involve pedestrians. The majority of the crashes occur during daytime hours, involve males, and involve persons in the 18-50 age group—Ethiopia’s active workforce. Crashes frequently occur in mid blocks or roadways. The predominant collision between motor vehicles and pedestrians was a rollover on a road tangent section. Failing to observe the priority of pedestrians and speeding were the major causes of crashes attributed by police. Trucks and minibus taxis were involved in the majority of crashes, while automobiles (small vehicles) were less involved in crashes relative to other vehicle types, partially because small vehicles tend to be driven fewer kilometres per annum. These data illustrate and justify a high priority to identify and implement effective programs, policies, and countermeasures focused on reducing pedestrian crashes.

Effects of mobile phone distraction on drivers’ reaction times

Distraction resulting from mobile phone use whilst driving has been shown to increase the reaction times of drivers, thereby increasing the likelihood of a crash. This study compares the effects of mobile phone conversations on reaction times of drivers responding to traffic events that occur at different points in a driver’s field of view. The CARRS-Q Advanced Driving Simulator was used to test a group of young drivers on various simulated driving tasks including a traffic event that occurred within the driver’s central vision—a lead vehicle braking suddenly—and an event that occurred within the driver’s peripheral—a pedestrian entering a zebra crossing from a footpath. Thirty-two licensed drivers drove the simulator in three phone conditions: baseline (no phone conversation), and while engaged in hands-free and handheld phone conversations. The drivers were aged between 21 to 26 years and split evenly by gender. Differences in reaction times for an event in a driver’s central vision were not statistically significant across phone conditions, probably due to a lower speed selection by the distracted drivers. In contrast, the reaction times to detect an event that originated in a distracted driver’s peripheral vision were more than 50% longer compared to the baseline condition. A further statistical analysis revealed that deterioration of reaction times to an event in the peripheral vision was greatest for distracted drivers holding a provisional licence. Many critical events originate in a driver’s periphery, including vehicles, bicyclists, and pedestrians emerging from side streets. A reduction in the ability to detect these events while distracted presents a significant safety concern that must be addressed.

Unidentified vehicle in multi-vehicle accident - failure to notify Nominal Defendant no bar to proceedings against it

In Kumar v Suncorp Metway Insurance Limited [2004] QSC 381 Douglas J examined s37 of the Motor Accident Insurance Act 1994 (Qld) in the context of an accident involving multiple insurers when a notice of accident had not been given to the Nominal Defendant

Advanced in-vehicle applications to mitigate driver aggression

Aggressive behavior at the steering wheel has been indicated as a contributing factor in a majority of crashes and anger has been compared to alcohol impairment in terms of probability to cause a crash. It has been shown that being in a state of anger or excitement while driving can decrease the drivers’ performances. . This paper reports the evaluation of 6 novel design alternatives of In-Vehicle Information Systems (IVIS) aimed at mitigating driver aggression. Each application presented was designed to tackle the following contributing factors to driver aggression: competitiveness, anonymity, territoriality, stress as well as social and emotional isolation. The 6 applications were simulated using computer vision algorithm to automatically overlay the real traffic conditions with ‘Head-Up Display’ visualizations. Two applications emerged over the others from participant’s evaluation: shared music combined the known calming effect of music with the sense of sympathy and intimacy caused by hearing other drivers’ music. The Shared Snapshot application provided an immediate gratification and was evaluated as a potential prevention of roadside quarrels. The paper presents Theoretical foundation, participant’s evaluations, implications and limitations of the study.

A comparison of factors influencing perceived risk by French and Australian cyclists and drivers

Differences in the levels of risk perceived by cyclists and car drivers may contribute to the dangers in their interactions. Levels of perceived risk have been shown to vary according to personal and environmental factors and between countries. Cycling rates in France are higher than in Australia, particularly among women. This study investigated whether cultural differences between France and Australia are reflected in perceived risks for experienced adult cyclists and drivers in the two countries. In online surveys, regular cyclists (France 336, Australia 444) and drivers (France 92, Australia 151) were asked to rate the level of risk in six situations: failure to yield; going through a red light; not signalling when turning; swerving; tail-gating; and not checking traffic. The effects of type of interacting vehicle and participant type on perceived risk were similar in France and Australia. However, the influence of responsibility for the risky behaviour differed according to participant type, type of situation and nationality. When the bicycle rider committed the road rule violation, Australian cyclists and drivers gave higher risk ratings than French cyclists and drivers. In both countries, cyclists rated themselves significantly higher than drivers on the perceived control and overconfidence subscales of the perceived skill measure. The French cyclists rated themselves higher than Australian cyclists on these scales, which could be responsible for overall lower perceived risk levels when interacting with a bike. Australian cyclists rated themselves significantly lower than drivers on the incompetence subscale but French cyclists rated themselves higher than drivers. In both countries incompetence scores were positively related to levels of perceived risk. Weekly time was associated with perceived risk in Australia but not in France. Frequency of traffic violations was not associated with perceived risk in either country. In conclusion, levels of perceived risk differed between drivers and cyclists in both countries and were influenced by type of interacting vehicle, experience and perceived skill. However, some differences between the results from the two countries merit further investigation to shed light on potential improvements in safety and cycling participation.

The impact of mobile phone distraction on the braking behaviour of young drivers : a hazard-based duration model

Braking is a crucial driving task with a direct relationship with crash risk, as both excess and inadequate braking can lead to collisions. The objective of this study was to compare the braking profile of young drivers distracted by mobile phone conversations to non-distracted braking. In particular, the braking behaviour of drivers in response to a pedestrian entering a zebra crossing was examined using the CARRS-Q Advanced Driving Simulator. Thirty-two licensed drivers drove the simulator in three phone conditions: baseline (no phone conversation), hands-free, and handheld. In addition to driving the simulator, each participant completed questionnaires related to driver demographics, driving history, usage of mobile phones while driving, and general mobile phone usage history. The drivers were 18–26 years old and split evenly by gender. A linear mixed model analysis of braking profiles along the roadway before the pedestrian crossing revealed comparatively increased decelerations among distracted drivers, particularly during the initial 20 kph of deceleration. Drivers’ initial 20 kph deceleration time was modelled using a parametric accelerated failure time (AFT) hazard-based duration model with a Weibull distribution with clustered heterogeneity to account for the repeated measures experiment design. Factors found to significantly influence the braking task included vehicle dynamics variables like initial speed and maximum deceleration, phone condition, and driver-specific variables such as licence type, crash involvement history, and self-reported experience of using a mobile phone whilst driving. Distracted drivers on average appear to reduce the speed of their vehicle faster and more abruptly than non-distracted drivers, exhibiting excess braking comparatively and revealing perhaps risk compensation. The braking appears to be more aggressive for distracted drivers with provisional licenses compared to drivers with open licenses. Abrupt or excessive braking by distracted drivers might pose significant safety concerns to following vehicles in a traffic stream.

Influence of visible work activity on drivers’ speed choice at roadworks

Vehicle traffic through roadwork sites creates a hazardous work environment, with speed limit noncompliance a major contributor to the high risk and high severity of roadwork crashes. This paper examines responses to an online survey to better understand the factors underlying drivers’ work zone speed choices. Drivers’ stated speed choice was compared between two photographs of the same work zone section – one with workers and machinery present and another with no visible activity. Drivers also provided comments on any aspect of roadwork safety they thought was important. A paired t-test of stated speed choice revealed that significantly lower mean speeds were nominated when workers and machinery were clearly present and active (41.7 vs 53.5 km/h, p<0.01). Participants expressed concern about roadwork signage and reduced speed limits being left in place when there was no apparent work activity. Driver perceptions, and thus compliance, may be improved through technological and operational changes.

Profiling contextual factors which influence safety in heavy vehicle industries

A significant proportion of worker fatalities within Australia result from truck-related incidents. Truck drivers face a number of health and safety concerns. Safety culture, viewed here as the beliefs, attitudes and values shared by an organisation’s workers, which interact with their surrounding context to influence behaviour, may provide a valuable lens for exploring safety-related behaviours in heavy vehicle operations. To date no major research has examined safety culture within heavy vehicle industries. As safety culture provides a means to interpret experiences and generate behaviour, safety culture research should be conducted with an awareness of the context surrounding safety. The current research sought to examine previous health and safety research regarding heavy vehicle operations to profile contextual factors which influence health and safety. A review of 104 peer-reviewed papers was conducted. Findings of these papers were then thematically analysed. A number of behaviours and scenarios linked with crashes and non-crash injuries were identified, along with a selection of health outcomes. Contextual factors which were found to influence these outcomes were explored. These factors were found to originate from government departments, transport organisations, customers and the road and work environment. The identified factors may provide points of interaction, whereby culture may influence health and safety outcomes.

“I would have lost the respect of my friends and family if they knew I had bent the road rules” : parents, peers, and the perilous behaviour of young drivers

Young novice drivers are at considerable risk of injury on the road. Their behaviour appears vulnerable to the social influence of their parents and friends. The nature and mechanisms of parent and peer influence on young novice driver (16–25 years) behaviour was explored via small group interviews (n = 21) and two surveys (n1 = 1170, n2 = 390) to inform more effective young driver countermeasures. Parental and peer influence occurred in preLicence, Learner, and Provisional (intermediate) periods. Pre-Licence and unsupervised Learner drivers reported their parents were less likely to punish risky driving (e.g., speeding). These drivers were more likely to imitate their parents and reported their parents were also risky drivers. Young novice drivers who experienced or expected social punishments from peers, including ‘being told off’ for risky driving, reported less riskiness. Conversely drivers who experienced or expected social rewards such as being ‘cheered on’ by friends – who were also more risky drivers – reported more risky driving including crashes and offences. Interventions enhancing positive influence and curtailing negative influence may improve road safety outcomes not only for young novice drivers, but for all persons who share the road with them. Parent-specific interventions warrant further development and evaluation including: modelling safe driving behaviour by parents; active monitoring of driving during novice licensure; and sharing the family vehicle during the intermediate phase. Peer-targeted interventions including modelling of safe driving behaviour and attitudes; minimisation of social reinforcement and promotion of social sanctions for risky driving also need further development and evaluation.

Unlicensed and unregistered vehicle project: Summary report. Report to Queensland Department of Transport and Main Roads

Unlicensed driving remains a serious problem for road safety, despite ongoing improvements in traffic law enforcement practices and technology. While it does not play a direct causative role in road crashes, unlicensed driving undermines the integrity of the driver licensing system and is associated with a range of high-risk behaviours. The Queensland Transport and Main Roads (TMR) commissioned a program of research with separate components relating to different aspects of unlicensed driving. Drawing on Australian and international studies, the Unlicensed and Unregistered Vehicle (UUV) project explores the nature of unlicensed driving in Queensland, consolidates the available research evidence and identifies gaps in current knowledge relating to the driving behaviours of unlicensed drivers.

Driver’s behavioural changes with new Intelligent Transport System interventions at railway level crossings: A driving simulator study

Improving safety at railway level crossings is an important issue for the Australian transport system. Governments, the rail industry and road organisations have tried a variety of countermeasures for many years to improve railway level crossing safety. New types of Intelligent Transport System (ITS) interventions are now emerging due to the availability and the affordability of technology. These interventions target both actively and passively protected railway level crossings and attempt to address drivers’ errors at railway crossings, which are mainly a failure to detect the crossing or the train and misjudgement of the train approach speed and distance. This study aims to assess the effectiveness of three emerging ITS that the rail industry considers implementing in Australia: a visual in-vehicle ITS, an audio in-vehicle ITS, as well as an on-road flashing beacons intervention. The evaluation was conducted on an advanced driving simulator with 20 participants per trialled technology, each participant driving once without any technology and once with one of the ITS interventions. Every participant drove through a range of active and passive crossings with and without trains approaching. Their speed approach of the crossing, head movements and stopping compliance were measured. Results showed that driver behaviour was changed with the three ITS interventions at passive crossings, while limited effects were found at active crossings, even with reduced visibility. The on-road intervention trialled was unsuccessful in improving driver behaviour; the audio and visual ITS improved driver behaviour when a train was approaching. A trend toward worsening driver behaviour with the visual ITS was observed when no trains were approaching. This trend was not observed for the audio ITS intervention, which appears to be the ITS intervention with the highest potential for improving safety at passive crossings.

Driving simulator evaluation of the failure of an audio in-vehicle warning for railway level crossings

It is impracticable to upgrade the 18,900 Australian passive crossings as such crossings are often located in remote areas, where power is lacking and with low road and rail traffic. The rail industry is interested in developing innovative in-vehicle technology interventions to warn motorists of approaching trains directly in their vehicles. The objective of this study was therefore to evaluate the benefits of the introduction of such technology. We evaluated the changes in driver performance once the technology is enabled and functioning correctly, as well as the effects of an unsafe failure of the technology? We conducted a driving simulator study where participants (N=15) were familiarised with an in-vehicle audio warning for an extended period. After being familiarised with the system, the technology started failing, and we tested the reaction of drivers with a train approaching. This study has shown that with the traditional passive crossings with RX2 signage, the majority of drivers complied (70%) and looked for trains on both sides of the rail track. With the introduction of the in-vehicle audio message, drivers did not approach crossings faster, did not reduce their safety margins and did not reduce their gaze towards the rail tracks. However participants’ compliance at the stop sign decreased by 16.5% with the technology installed in the vehicle. The effect of the failure of the in-vehicle audio warning technology showed that most participants did not experience difficulties in detecting the approaching train even though they did not receive any warning message. This showed that participants were still actively looking for trains with the system in their vehicle. However, two participants did not stop and one decided to beat the train when they did not receive the audio message, suggesting potential human factors issues to be considered with such technology.