Chaotic Dynamics of Semiconductor Laser with Current Modulation and optoelectronic feedback

Chaotic dynamics of directly modulated semiconductor lasers have been studied extensively over the last two decades because of their application in secure optical communication. However, chaos is generally suppressed in such systems when the nonlinear gain reduction factor is above 0.01 which is very much smaller than the reported values in semiconductors like InGaAsP. In this paper we show that by giving an optoelectronic feedback with appropriate delay one can increase the range of the values of the gain reduction factor for which chaos can be observed. Numerical studies show that negative feedback is more efficient in producing chaotic dynamics.

Realization of a Scanning Photoacoustic Technique: Thermal properties of Bulk and Film Samples

Among the large number of photothcrmal techniques available, photoacoustics assumes a very significant place because of its essential simplicity and the variety of applications it finds in science and technology. The photoacoustic (PA) effect is the generation of an acoustic signal when a sample, kept inside an enclosed volume, is irradiated by an intensity modulated beam of radiation. The radiation absorbed by the sample is converted into thermal waves by nonradiative de-excitation processes. The propagating thermal waves cause a corresponding expansion and contraction of the gas medium surrounding the sample, which in tum can be detected as sound waves by a sensitive microphone. These sound waves have the same frequency as the initial modulation frequency of light. Lock-in detection method enables one to have a sufficiently high signal to noise ratio for the detected signal. The PA signal amplitude depends on the optical absorption coefficient of the sample and its thermal properties. The PA signal phase is a function of the thermal diffusivity of the sample.Measurement of the PA amplitude and phase enables one to get valuable information about the thermal and optical properties of the sample. Since the PA signal depends on the optical and thennal properties of the sample, their variation will get reflected in the PA signal. Therefore, if the PA signal is collected from various points on a sample surface it will give a profile of the variations in the optical/thennal properties across the sample surface. Since the optical and thermal properties are affected by the presence of defects, interfaces, change of material etc. these will get reflected in the PA signal. By varying the modulation frequency, we can get information about the subsurface features also. This is the basic principle of PA imaging or PA depth profiling. It is a quickly expanding field with potential applications in thin film technology, chemical engineering, biology, medical diagnosis etc. Since it is a non-destructive method, PA imaging has added advantages over some of the other imaging techniques. A major part of the work presented in this thesis is concemed with the development of a PA imaging setup that can be used to detect the presence of surface and subsmface defects in solid samples.Determination of thermal transport properties such as thermal diffusivity, effusivity, conductivity and heat capacity of materials is another application of photothennal effect. There are various methods, depending on the nature of the sample, to determine these properties. However, there are only a few methods developed to determine all these properties simultaneously. Even though a few techniques to determine the above thermal properties individually for a coating can be found in literature, no technique is available for the simultaneous measurement of these parameters for a coating. We have developed a scanning photoacoustic technique that can be used to determine all the above thermal transport properties simultaneously in the case of opaque coatings such as paints. Another work that we have presented in this thesis is the determination of thermal effusivity of many bulk solids by a scanning photoacoustic technique. This is one of the very few methods developed to determine thermal effiisivity directly.

Synergic Reactions in the Estuarine Environment leading to Modulation of Aluminium metal during Transport Processes (in Cochin Estuary)

The research work which was carried out to Synergic Reactions in the Estuarine Environment leading to Modulation of Aluminium metal during Transport Processes (in Cochin Estuary)Estuaries are considered as sink or source for terrestrial and various anthropogenically generated materials. These include naturally occurring elements Al, Si, Fe or trace inorganics or industrial pollutants of different types. There have been reports on both positive and negative impacts by the introduction of above materials into the ecosystem.This thesis deals with the trace metal Aluminium (Al) whose average concentration (about 8%) in the earths crust is surpassed only by that of Oxygen and Silicon. There can be no doubt that most of the land derived materials reaches the ocean through rivers via estuaries. An important aspect noticed here is that the concentration of dissolved Al is much lower in sea water than in river water.On critically analysing Cochin estuary, for the entire cycles, covering monsoon, postmonsoon and premonsoon, the following salient features are documented as hereunder. Dissolved Al exhibits high and variable trends in Cochin estuary, the influencing parameters being salinity, SPM, pH and dissolved Si. A general profile showed removal in upper/mid estuary followed by regeneration in the mid/lower estuary and further decrease seawards in the southern/northem arms.Distribution appears to be a function of freshwater input, the monsoon season exhibiting very high concentrations throughout the estuary. As the river discharge decreased with the progress of seasons, dissolved Al concentration also decreased, the metal limiting itself to the upper and mid estuary.

Environmental Influences on the Frequency and Intensity of North Indian Ocean Tropical Cyclones

Tropical cyclones genesis, movement and intensification are highly dependent on its environment both oceanic and atmospheric. This thesis has made a detailed study on the environmental factors related to tropical cyclones of North Indian Ocean basin. This ocean basin has produced only 6% of the global tropical cyclones annually but it has caused maximum loss of human life associated with the strong winds, heavy rain and particularly storm surges that accompany severe cyclones as they strike the heavily populated coastal areas. Atmospheric factors studied in the thesis are the moisture content of the atmosphere, instability of the atmosphere that produces thunderstorms which are the main source of energy for the tropical cyclone, vertical wind shear to which cyclones are highly sensitive and the Sub-Tropical westerly Jetsteram and its Asian high speed center. The oceanic parameters studied are sea surface temperature and heat storage in the top layer of the ocean. A major portion of the thesis has dealt with the three temporal variabilities of tropical cyclone frequency namely intra-seasonal (mainly the influence of Madden Julian Oscillation), inter- annual (the relation with El Nino Southern Oscillation) and decadal variabilities. Regarding decadal variability, a prominent four decade oscillation in the frequency of both tropical cyclones and monsoon depressions unique to the Indian Ocean basin has been brought out. The thesis consists of 9 chapters.

Spatial and temporal characteristics of rain intensity in the peninsular Malaysia using TRMM rain rate

The present study is focused on the intensity distribution of rainfall in different classes and their contribution to the total seasonal rainfall. In addition, we studied the spatial and diurnal variation of the rainfall in the study areas. For the present study, we retrieved data from TRMM (Tropical Rain Measuring Mission) rain rate available in every 3 h temporal and 25 km spatial resolutions. Moreover, station rainfall data is used to validate the TRMM rain rate and found significant correlation between them (linear correlation coefficients are 0.96, 0.85, 0.75 and 0.63 for the stations Kota Bharu, Senai, Cameron highlands and KLIA, respectively). We selected four areas in the Peninsular Malaysia and they are south coastal, east coastal, west coastal and highland regions. Diurnal variation of frequency of rain occurrence is different for different locations. We noticed bimodal variation in the coastal areas in most of the seasons and unimodal variation in the highland/inland area. During the southwest monsoon period in the west coastal stations, there is no distinct diurnal variation. The distribution of different intensity classes during different seasons are explained in detail in the results

Long term trends of seasonal and monthly rainfall in different intensity ranges over Indian subcontinent

In general Indian summer monsoon rainfall did not show any significant trend in all Indian summer monsoon rainfall series, however, it was reported that the ISMR is subjected to spatial trends. This paper made an attempt to bring out long term trends of different intensity classes of summer monsoon rainfall in different regions of Indian subcontinent. The long term trend of seasonal and monthly rainfall were also made using the India Meteorological Department gridded daily rainfall data with a spatial resolution of 1° × 1° latitude-longitude grid for the period from 1st January, 1901 to 31st December, 2003. The summer monsoon rainfall shows an increasing trend in southeast, northwest and northeast regions, whereas decreasing trend in the central and west coastal regions. In monthly scale, July rainfall shows decreasing trend over west coastal and central Indian regions and significant increasing trend over northeast region at 0.1% significant level. During the month August, decreasing trend is observed in the west coastal stations at 10% significant level. In most of the stations, mean daily rainfall shows an increasing trend for low and very high intense rainfall. For the moderate rainfall, the trend is different for different regions. In the central and southern regions the trend of moderate and moderately high classes show increasing trend. And for the high and very high intensity classes, the trend is decreasing significantly. In the northeastern regions, above 10 mm/day rainfall shows significantly increasing trend with 0.1% significant level.

A New Gridding Technique for High Density Microarray Images Using Intensity Projection Profile of Best Sub Image

As the technologies for the fabrication of high quality microarray advances rapidly, quantification of microarray data becomes a major task. Gridding is the first step in the analysis of microarray images for locating the subarrays and individual spots within each subarray. For accurate gridding of high-density microarray images, in the presence of contamination and background noise, precise calculation of parameters is essential. This paper presents an accurate fully automatic gridding method for locating suarrays and individual spots using the intensity projection profile of the most suitable subimage. The method is capable of processing the image without any user intervention and does not demand any input parameters as many other commercial and academic packages. According to results obtained, the accuracy of our algorithm is between 95-100% for microarray images with coefficient of variation less than two. Experimental results show that the method is capable of gridding microarray images with irregular spots, varying surface intensity distribution and with more than 50% contamination

Highly Sensitive Sensor Based On Intracavity Laser Absorption Spectroscopy By Means of Relative Intensity Noise

This thesis concerns with the main aspects of medical trace molecules detection by means of intracavity laser absorption spectroscopy (ICLAS), namely with the equirements for highly sensitive, highly selective, low price, and compact size sensor. A novel two modes semiconductor laser sensor is demonstrated. Its operation principle is based on the competition between these two modes. The sensor sensitivity is improved when the sample is placed inside the two modes laser cavity, and the competition between the two modes exists. The effects of the mode competition in ICLAS are discussed theoretically and experimentally. The sensor selectivity is enhanced using external cavity diode laser (ECDL) configuration, where the tuning range only depends on the external cavity configuration. In order to considerably reduce the sensor cost, relative intensity noise (RIN) is chosen for monitoring the intensity ratio of the two modes. RIN is found to be an excellent indicator for the two modes intensity ratio variations which strongly supports the sensor methodology. On the other hand, it has been found that, wavelength tuning has no effect on the RIN spectrum which is very beneficial for the proposed detection principle. In order to use the sensor for medical applications, the absorption line of an anesthetic sample, propofol, is measured. Propofol has been dissolved in various solvents. RIN has been chosen to monitor the sensor response. From the measured spectra, the sensor sensitivity enhancement factor is found to be of the order of 10^(3) times of the conventional laser spectroscopy.

Effects of tillage intensity on soil C, N, and P pools with different stability

Es ist bekannt, dass die Umsatzdynamik der organischen Substanz von der Bodenbearbeitungsintensität abhängt. Bis jetzt sind nur wenige Daten zum Einfluss der Bearbeitungsintensität und des Zwischenfruchtanbaus auf C-, N-, und P-Dynamik im Ober- (0-5 cm Tiefe) und Unterboden (5-25 cm Tiefe) von Lössböden verfügbar. Hauptziele dieser Arbeit waren die (i) Quantifizierung des Einflusses von verschiedenen langzeitig durchgeführten Bearbeitungssystemen auf labile, intermediäre, und passive C- und N-Pools; (ii) Quantifizierung des Einflusses dieser Systeme auf P-Fraktionen mit unterschiedlicher Verfügbarkeit für die Pflanzenaufnahme; (iii) Quantifizierung des Einflusses des Zwischenfruchtanbaus in Verbindung mit einer unterschiedlichen Einarbeitungstiefe der der Zwischenfrüchte auf mineralisierbares C und N. Die Ergebnisse des 1. und 2. Teilexperiments basieren auf Untersuchungen von 4 Langzeitfeldexperimenten (LFE) in Ost- und Süddeutschland, die zwischen 1990 und 1997 durch das Institut für Zuckerrübenforschung angelegt wurden. Jedes LFE umfasst 3 Bearbeitungssysteme: konventionelle Bearbeitung (CT), reduzierte Bearbeitung (RT) und Direktsaat (NT). Die Ergebnisse des 3. Teilexperiments basieren auf einem Inkubationsexperiment. Entsprechend den Hauptfragestellungen wurden folgende Untersuchungsergebnisse beschrieben: (i) Im Oberboden von NT wurden höhere labile C-Vorräte gefunden (C: 1.76 t ha-1, N: 166 kg ha-1), verglichen mit CT (C: 0.44 t ha-1, N: 52 kg ha-1). Im Gegensatz dazu waren die labile- C-Vorräte höher im Unterboden von CT mit 2.68 t ha-1 verglichen zu NT mit 2 t ha-1 und RT mit 1.87 t ha-1. Die intermediären C-Vorräte betrugen 73-85% der gesamten organischen C-Vorräte, intermediäre N-Vorräte betrugen 70-95% des Gesamt-N im Ober- und Unterboden und waren vielfach größer als die labilen und passiven C- und N-Vorräte. Nur im Oberboden konnte ein Effekt der Bearbeitungsintensität auf die intermediären N-Pools mit höheren Vorräten unter NT als CT festgestellt werden. Die passiven C- und N-Pools waren eng mit den mineralischen Bodeneigenschaften verbunden und unabhängig vom Bearbeitungssystem. Insgesamt hat sich gezeigt, dass 14 bis 22 Jahre durchgängige Direktsaatverfahren nur im Oberboden zu höheren labilen C- und N-Vorräten führen, verglichen zu konventionellen Systemen. Dies lässt eine tiefenabhängige Stärke der Dynamik der organischen Bodensubstanz vermuten. (ii) Die Konzentration des Gesamt-P (Pt) im Oberboden war höher in NT (792 mg kg-1) und ~15% höher als die Pt-Konzentration in CT (691 mg kg 1). Die Abnahme der Pt-Konzentration mit zunehmender Bodentiefe war höher in NT als in CT. Dies gilt auch für die einzelnen P-Fraktionen, ausgenommen der stabilsten P-Fraktion (residual-P). Generell hatte das Bearbeitungssystem nur einen kleinen Einfluss auf die P-Konzentration mit höheren Pt-Konzentrationen in Böden unter NT als CT. Dies resultiert vermutlich aus der flacheren Einarbeitung der Pflanzenreste als in CT. (iii) Im Zwischenfruchtexperiment war der Biomassezuwachs von Senf am höchsten und nimmt in der Reihenfolge ab (oberirdischer Ertrag in t / ha): Senf (7.0 t ha-1) > Phacelia (5.7 t ha-1) > Ölrettich (4.4 t ha-1). Damit war potentiell mineralisierbares C und N am höchsten in Böden mit Senfbewuchs. Kumulative CO2- und N2O-Emissionen während der Inkubation unterschieden sich nicht signifikant zwischen den Zwischenfruchtvarianten und waren unabhängig von der Verteilung der Pflanzenreste im Boden. Die kumulativen ausgewaschenen mineralisierten N (Nmin)-Vorräte waren in den brachliegenden Böden am höchsten. Die Nmin-Vorräte waren 51-72% niedriger in den Varianten mit Zwischenfrucht und Einarbeitung verglichen zur Brache. In den Varianten ohne Einarbeitung waren die Nmin-Vorräte 36-55% niedriger verglichen zur Brache. Dies weißt auf einen deutlichen Beitrag von Zwischenfrüchten zur Reduzierung von Nitrat-Auswaschung zwischen Winter und Frühjahr hin. Insgesamt führte reduzierte Bearbeitung zu einer Sequestrierung von C und N im Boden und der Zwischenfruchtanbau führte zu reduzierten N-Verlusten. Die P-Verfügbarkeit war höher unter Direktsaat verglichen zur konventionellen Bearbeitung. Diese Ergebnisse resultieren aus den höheren Konzentrationen der OS in den reduzierten, als in den konventionellen Systemen. Die Ergebnisse zeigen deutlich das Potential von reduzierter Bearbeitung zur Sequestrierung von intermediärem C und N zur Reduzierung von klimarelevanten Treibhausgasen. Gleichzeitig steigen die Konzentrationen an pflanzenverfügaren P-Gehalten. Zwischenfrüchte führen auch zu einem Anstieg der C- und N-Vorräte im Boden, offensichtlich unabhängig von der Zwischenfruchtart.

Interferometrische Sensoren mit Modulation der optischen Weglänge für die Fertigungsmesstechnik

Ziel dieser Dissertation ist es, eine Klasse interferometrischer Messgeräte zu charakterisieren und weiter zu entwickeln. Die Modulation der optischen Weglänge (OPLM) im Referenzarm eines interferometrischen Messsystems ist ein anpassungsfähiger Ansatz. Sie ist zur Messung von Oberflächenprofilen mit einer Auflösung bis in den sub-nm-Bereich bei einem Messbereich von bis zu 100 Mikrometer geeignet. Wird ein statisches Messobjekt gemessen, tritt durch die Modulation im Referenzarm am Detektor ein periodisches Interferenzmuster auf. Dies ist in der unten stehenden Abbildung schematisch dargestellt. Bei einer Veränderung des Abstandes zwischen Objekt und Messgerät kann aus der Phasen- und/oder Hüllkurvenverschiebung im Interferenzmuster die Abstandsänderung abgeleitet werden.Im Rahmen der Arbeit sind zwei funktionsfähige OPLM-Messsysteme entwickelt, aufgebaut und getestet worden. Diese demonstrieren, dass der OPLM-Ansatz ein breites Spektrum an Anwendungen durch eine optische Messung abdecken kann. Allerdings zeigen sich an den Messsystemen auch die Limitierungen des OPLM-Ansatzes. Die Systeme basieren auf einer Punktmessung mittels einer fasergekoppelten Sonde sowie auf einer linienförmigen Messung durch eine Zeilenkamera. Um eine hohe laterale Auflösung zu erzielen, wird die Zeilenkamera mit einem Mikroskop kombiniert. Damit flächenhaft gemessen werden kann, ist es notwendig, Messobjekt und Sensor zueinander zu verschieben. Daher wird eine Theorie entwickelt, unter welchen Randbedingungen bewegte Objekte von einem OPLM-Messsystem aufgelöst werden können. Die Theorie wird anschließend experimentell überprüft und bestätigt. Für die Auswertung der bei der Modulation der optischen Weglänge entstehenden Interferenzen existieren bereits einige erprobte Algorithmen, welche auf ihre Eignung hin untersucht und mit selbst entwickelten Algorithmen verglichen werden. Auch wird darauf eingegangen, welches die zentralen Herausforderungen bei der Planung von OPLM-Interferometern sind und wie sich insbesondere die Wahl des Aktors für die OPLM auf das gesamte Messsystem auswirkt. Bei den beiden Messsystemen werden jeweils wichtige Komponenten wie analoge Elektronik und Aktorik sowie ihre Funktionsweise erläutert. Es wird detailliert beschrieben, wie ein OPLM-Messsystem charakterisiert und kalibriert werden muss, um möglichst zuverlässige Messwerte zu liefern. Abschließend werden die Möglichkeiten der beiden entwickelten Systeme durch Beispielmessungen demonstriert, sowie ihre Messgenauigkeit charakterisiert.

Notes on analogue and digital amplitude modulation

Notes on AM, DSBSC, QAM, BPSK, 4QAM, 8PSK, 16QAM

Assignment on Modulation

Considers Sampling, Pulse Amplitude Modulation, Multiple Access, Quantisation, Pulse Coded Modulation, Manchester Line Coding, Amplitude Modulation, Double SideBand Suppressed Carrier Modulation, Quadrature Amplitude Modulation and M-ary Shift Keying.

Recognition of static and dynamic facial expressions: Influences of sex, type and intensity of emotion

Ecological validity of static and intense facial expressions in emotional recognition has been questioned. Recent studies have recommended the use of facial stimuli more compatible to the natural conditions of social interaction, which involves motion and variations in emotional intensity. In this study, we compared the recognition of static and dynamic facial expressions of happiness, fear, anger and sadness, presented in four emotional intensities (25 %, 50 %, 75 % and 100 %). Twenty volunteers (9 women and 11 men), aged between 19 and 31 years, took part in the study. The experiment consisted of two sessions in which participants had to identify the emotion of static (photographs) and dynamic (videos) displays of facial expressions on the computer screen. The mean accuracy was submitted to an Anova for repeated measures of model: 2 sexes x [2 conditions x 4 expressions x 4 intensities]. We observed an advantage for the recognition of dynamic expressions of happiness and fear compared to the static stimuli (p < .05). Analysis of interactions showed that expressions with intensity of 25 % were better recognized in the dynamic condition (p < .05). The addition of motion contributes to improve recognition especially in male participants (p < .05). We concluded that the effect of the motion varies as a function of the type of emotion, intensity of the expression and sex of the participant. These results support the hypothesis that dynamic stimuli have more ecological validity and are more appropriate to the research with emotions.

Educational failure in Spain : evolution, intensity and determinants. 'Fracaso escolar en España : evolución, intensidad y factores determinantes'.

Resumen basado en el de la publicación

Youth-culture or student-culture?: the internet use intensity divide among university students and the consequences for academic performance. '¿Cultura juvenil o cultura estudiantil? : el uso de Internet divide a los estudiantes universitarios : consecuencias para el rendimiento académico'.

Resumen tomado de la publicación