pH mediated delamination of anionic clay-like nickel-zinc hydroxysalt in water through intercalation of zwitterionic p-aminobenzoate ions

p-aminobenzoate could be intercalated into the anionic clay, Ni3Zn2(OH)(8)(OAc)(2)center dot 2H(2)O at a high pH (similar to 10). When the pH was reduced to similar to 7 while washing colloidal dispersion due to delamination was observed. The development of partial positive charge on the amine end of the intercalated anion causes repulsion between the layers leading to delamination and colloidal dispersion of monolayers in water. The layers could be restacked from the colloid to form the parent solid either by increasing the pH or by evaporation.

On the hardness and elastic modulus of bulk metallic glass matrix composites

The influences of the amorphous matrix and crystalline dendrite phases on the hardness and elastic moduli of Zr/Ti-based bulk metallic glass matrix composites have been assessed. While the moduli of the composites correspond to those predicted by the rule of mixtures, the hardness of the composites is similar to that of the matrix, suggesting that the plastic flow in the composites under constrained conditions such as indentation is controlled by the flow resistance of the contiguous matrix. (C) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Fractional-factorial design of a porous-carbon fuel-cell electrode

The use of fractional-factorial methods in the optimization of porous-carbon electrode structure is discussed with respect to weight-loss of carbon during gas treatment, weight and mixing time of binder, compaction temperature, time and pressure, and pressure of feed gas. The experimental optimization of an air electrode in alkaline solution is described.

The elastic manifestation of a spin-glass transition: a low-frequency study

The authors report here the first measurements of low-frequency dynamic elastic properties of a spin glass (Fe59Ni21Cr20) across the transition temperature (Tg approximately=16 K). A minimum in the sound velocity (V) and a maximum in the internal friction (Q-1) were found at temperatures close to but below Tg. The elastic data were compared with the AC susceptibility data taken at similar frequency.

Electrochemical reduction of Cu(II)-CyDTA complex at dropping mercury electrode. An impedance approach

The electrochemical reduction of Cu(II)-CyDTA (CyDTA — trans 1,2-cyclohexanediamine N, N, N′, N′ tetraacetic acid) by impedance method reveals the unusual behaviour of complex plane polarograms owing to potential dependence of double layer capacitance. The impedance plane plots by frequency variation method indicates the quasi-reversible nature of the system. From these plots the chargetransfer resistance at various potentials was evaluated. The standard rate constant was evaluated which complements the prediction of impedance plots for the quasireversible behaviour of the system.

Electrochemical reduction of Cu(II)-EDTA complex at dropping mercury electrode. An impedance approach

The study of electrochemical reduction of Cu(II)-EDTA system by phase sensitive a.c. impedance method at dropping mercury electrode reveals several interesting features. The complex plane polarograms exhibit loop like shape in contrast to the classical zinc ion reduction where crest like shape is found. Again, the relative placement of peaks of in-phase and quadrature components, and the relative placement of portions before and after the peaks of complex plane polarograms are different from that of zinc ion reduction. The complex plane plots suggest that electrochemical reduction of Cu-EDTA is charge transfer controlled.

Thermal reactivity of ammonium perchlorate crystallised from solutions having different pH

The thermal reactivity of ammonium perchlorate was found to be dependent on the pH of the solution from which it had been crystallised. A nitric acid-crystallised sample reacted faster than an ammonium hydroxide-crystallised one.

Structural, optical and electrical characteristics of transparent bismuth vanadate films deposited on indium tin oxide coated glass substrates

Bismuth vanadate (BVO) thin films were fabricated on indium tin oxide (ITO) coated glass substrates using pulsed laser ablation technique and investigated their structural, optical and electrical properties. The use of the indium tin oxide coated glass substrate resulted in reducing the leakage current characteristics of crystalline BVO thin films. The X-ray diffraction (XRD) studies confirmed the monophasic nature of the post annealed (500 A degrees C/1 h) films. The atomic force microscopy indicated the homogeneous distribution of crystallites in the as-deposited films. The as-deposited and the post annealed films were almost 90% transparent (380-900 nm) as confirmed by optical transmission studies. Dielectric constant of around 52 was attained accompanied by the low dielectric loss of 0.002 at 10 kHz for post annealed films. The leakage current of the post annealed BVO films on ITO coated glass substrates measured at room temperature was 8.1 x 10(-8) A at an applied electric field of 33 kV/cm, which was lower than that of the films with platinum and SrRuO3 as the bottom electrodes.

An EQCM Investigation of Electrochemical Precipitation of Mn(OH)(2) and Its Capacitance Behavior

Electrochemical quartz crystal microbalance (EQCM) has been used to study the electrochemical precipitation of Mn(OH)(2) on a Au crystal and its capacitance properties. From the EQCM data, it is inferred that NO3- ions get adsorbed on the Au crystal and then undergo reduction, resulting in an increase in pH near the electrode surface. Precipitation of Mn2+ occurs as Mn(OH)(2), with an increase in mass of the Au crystal. Mn(OH)(2) undergoes oxidation to MnO2, which exhibits electrochemical supercapacitor behavior on subjecting to electrochemical cycling in a Na2SO4 electrolyte. EQCM data indicate mass variations corresponding to surface insertion/extraction of Na+ ions during discharge/charge cycling. (C) 2010 The Electrochemical Society. DOI: 10.1149/1.3479665] All rights reserved.

Formation of lead pyrophosphate glass and the role of anion disproportionation

Thermal, spectroscopic and electrical properties of lead pyrophosphate glass prepared by melt quenching have been examined. A model based on the structural disproportionation of the P2O 7 4− ions has been proposed and is shown to consistently explain all the observations. The equilibrium of various anionic species has been discussed on the basis of their electronegativities which are in turn related to their basicities.

Low-temperature internal friction of glass ceramics

Low-temperature internal-friction measurements have been used to study the universal low-energy excitations in glasses before and after crystallization in two glass ceramics, one based on MgO-Al2O3-SiO2 (Corning Code 9606) and one based on Li2O-Al2O3-SiO2 (Corning Code 9623). In the Code 9606 sample, the number density of excitations is greatly reduced, while in the Code 9623 sample, their number density remains practically unaltered in the crystallized state. These measurements confirm the conclusions reached by Cahill et al. (preceding paper), which were based on thermal measurements up to room temperature. These measurements also demonstrate the usefulness of internal friction as a tool for the study of these low-energy excitations, since internal friction is less sensitive to defects common to glass ceramics, like magnetic impurities and grain boundaries, which tend to dominate low-temperature specific heat and thermal conductivity, respectively.

Radio interference measurements on a ceramic disc insulator string with field reduction electrode

This paper presents a laboratory study of the discharge radio noise generated by ceramic insulator strings under normal conditions. In the course of study, a comparison on the performance of two types of insulator strings under two different conditions was studied namely (a) normal disc insulators in a string and (b) disc insulators integrated with a newly developed field reduction electrode fixed to the disc insulator at the pin junction. The results obtained during the study are discussed and presented.

Potentiodynamic behaviour of β-lead dioxide in neutral media at positive potentials

The behaviour of the PbO2 electrode in NaNO3, Na2SO4 NaClO4 and NaCl in the pH range 3.0–10.5 has been studied by cyclic voltammetry. When the electrode is cycled between 0.30 and 1.90 V, a large cathodic current peak appears in the negative scan; in the subsequent cycle, two anodic peaks appear. The addition of H2O2 at low concentrations to the electrolyte also results in two anodic peaks at the same potentials. A number of possible explanations for the appearance of the cathodic peak, and a mechanism for the oxidation of PbO to PbO2 through Pb3O4 corresponding to the two anodic peaks, are proposed.

Platinum particles supported on titanium nitride: an efficient electrode material for the oxidation of methanol in alkaline media

In the present study, titanium nitride which shows exceptional stability, extreme corrosion resistance, good electronic conductivity and adhesion behaviour is used to support platinum particles and then used for methanol oxidation in an alkaline medium. The catalyst shows very good CO tolerance for the electrochemical oxidation of methanol. In situ infrared spectroelectrochemical data show the remarkable ability of TiN to decompose water at low over potentials leading to -OH type functional groups on its surface which in turn help in alleviating the carbon monoxide poisoning associated with methanol oxidation. TiN supported catalysts are found to be very good in terms of long term stability, exchange current density and stable currents at low over voltages. Supporting evidence from X-ray photoelectron spectroscopic data and cyclic voltammetry clearly demonstrates the usefulness of TiN supported Pt catalysts for efficient methanol oxidation in alkaline media.

Deformation and structural densification in Al2O3-Y2O3 glass

In this article, we examine the unusual plastic deformation under uniaxial compression of an Al2O3-15 mol % Y2O3 (A15Y) glass synthesized by a wet chemical route At a low temperature of 650-725 degrees C, plastic deformation of this glass is largely non-viscous through shear instabilities In contrast deformation near the crystallization temperature (850 degrees C) occurs homogeneously with work hardening and with a monotonic increase in the true density of the glass by 10-12% accompanied by an increase in hardness (H) and elastic modulus (E) of up to 100% We hypothesize a phenomenon of molecular densification of the amorphous structure through a hierarchy of multiple phases, analogous to density- or entropy-driven amorphous to-amorphous phase transitions (polyamorphism) These results suggest that the present method of preparation and the unusual behavior can trigger a search for many more systems that display such behavior (C) 2010 Acta Materialia Inc Published by Elsevier Ltd All rights reserved