Puhdistetun jäteveden patogeenit ja desinfiointitarve

Turun seudulla kuuden kunnan jätevesien käsittely keskitetään Kakolanmäen kallion sisälle rakennettuun jätevedenpuhdistamoon, joka otetaan käyttöön vuoden 2008 lopulla. Kakolanmäen jätevedenpuhdistamolla on varauduttu tulevaisuudessa kiristyviin lupaehtoihin sekä mahdollisiin puhdistetun jäteveden hygieenistä laatua koskeviin lisämääräyksiin jättämällä tilavaraus puhdistetun jäteveden desinfioimiselle ultraviolettivalolla. Diplomityössä on selvitetty vuoden kestäneessä tutkimusjaksossa 1.9.2006- 31.8.2007 Turun kaupungin keskuspuhdistamolta mereen johdetun puhdistetun jäteveden ja esiselkeytetyn ohitusveden hygieenisen laadun vaihtelua. Jäteveden desinfiointitarvetta on arvioitu tarkastelemalla jätevedenpuhdistamon hygieenistä puhdistustulosta ja jätevesien vaikutusta purkuvesistön hygieeniseen tilaan. Tutkimuksen perusteella virtaama ei vaikuttanut merkittävästi jäteveden ulosteperäisten bakteerien määriin. Sen sijaan jäteveden bakteeripitoisuudet laskivat alhaisissa lämpötiloissa. Lämpötilan vaikutus näkyi selkeämmin esiselkeytetyssä kuin puhdistetussa jätevedessä eli bakteerien poistumiseen aktiivilietevaiheen aikana vaikuttavat muut tekijät. Mitä tehokkaammin aktiivilietevaihe toimi, sitä tehokkaammin myös bakteereja poistui. Taudinaiheuttajabakteerit selvisivät puhdistusprosessista paremmin viileän kauden aikana. Puhdistetun jäteveden hygieeninen laatu ei täyttänyt uimaveden tai kasteluveden laatuvaatimuksia, joten desinfiointitarve olisi perustelua. Jätevesien vaikutus Turun edustan merialueen hygieeniseen tilaan näkyi ajoittain korkeina bakteeripitoisuuksina purkupaikan lähistöllä. Vielä ei ole suoraa näyttöä siitä aiheuttavatko jätevedet purkupaikan lähistön uimarannoilla terveydellisiä riskejä. Jäteveden UV-desinfiointi kannattava toteuttaa vain jos hygieeninen puhdistusvelvoite määrätään. UV-desinfioinnin mitoituksessa Kakolanmäen jätevedenpuhdistamolla tulee ottaa huomioon suurin sallittu hydraulinen painehäviö. Mitoitus voidaan tehdä puhdistamon käyttöönoton jälkeen kun tarvitut prosessimittaustiedot ovat saatavilla.

Drivers and Barriers of Collaboration in the Value Chain of Paperboard-Packed Consumer Goods

Value chain collaboration has been a prevailing topic for research, and there is a constantly growing interest in developing collaborative models for improved efficiency in logistics. One area of collaboration is demand information management, which enables improved visibility and decrease of inventories in the value chain. Outsourcing of non-core competencies has changed the nature of collaboration from intra-enterprise to cross-enterprise activity, and this together with increasing competition in the globalizing markets have created a need for methods and tools for collaborative work. The retailer part in the value chain of consumer packaged goods (CPG) has been studied relatively widely, proven models have been defined, and there exist several best practice collaboration cases. The information and communications technology has developed rapidly, offering efficient solutions and applications to exchange information between value chain partners. However, the majority of CPG industry still works with traditional business models and practices. This concerns especially companies operating in the upstream of the CPG value chain. Demand information for consumer packaged goods originates at retailers' counters, based on consumers' buying decisions. As this information does not get transferred along the value chain towards the upstream parties, each player needs to optimize their part, causing safety margins for inventories and speculation in purchasing decisions. The safety margins increase with each player, resulting in a phenomenon known as the bullwhip effect. The further the company is from the original demand information source, the more distorted the information is. This thesis concentrates on the upstream parts of the value chain of consumer packaged goods, and more precisely the packaging value chain. Packaging is becoming a part of the product with informative and interactive features, and therefore is not just a cost item needed to protect the product. The upstream part of the CPG value chain is distinctive, as the product changes after each involved party, and therefore the original demand information from the retailers cannot be utilized as such – even if it were transferred seamlessly. The objective of this thesis is to examine the main drivers for collaboration, and barriers causing the moderate adaptation level of collaborative models. Another objective is to define a collaborative demand information management model and test it in a pilot business situation in order to see if the barriers can be eliminated. The empirical part of this thesis contains three parts, all related to the research objective, but involving different target groups, viewpoints and research approaches. The study shows evidence that the main barriers for collaboration are very similar to the barriers in the lower part of the same value chain; lack of trust, lack of business case and lack of senior management commitment. Eliminating one of them – the lack of business case – is not enough to eliminate the two other barriers, as the operational model in this thesis shows. The uncertainty of the future, fear of losing an independent position in purchasing decision making and lack of commitment remain strong enough barriers to prevent the implementation of the proposed collaborative business model. The study proposes a new way of defining the value chain processes: it divides the contracting and planning process into two processes, one managing the commercial parts and the other managing the quantity and specification related issues. This model can reduce the resistance to collaboration, as the commercial part of the contracting process would remain the same as in the traditional model. The quantity/specification-related issues would be managed by the parties with the best capabilities and resources, as well as access to the original demand information. The parties in between would be involved in the planning process as well, as their impact for the next party upstream is significant. The study also highlights the future challenges for companies operating in the CPG value chain. The markets are becoming global, with toughening competition. Also, the technology development will most likely continue with a speed exceeding the adaptation capabilities of the industry. Value chains are also becoming increasingly dynamic, which means shorter and more agile business relationships, and at the same time the predictability of consumer demand is getting more difficult due to shorter product life cycles and trends. These changes will certainly have an effect on companies' operational models, but it is very difficult to estimate when and how the proven methods will gain wide enough adaptation to become standards.

A bench arc-furnace facility for fullerene and single-wall nanotubes synthesis

A metallic-sample arc-furnace was modified to synthesize fullerenes and nanotubes. The (reversible) changes and the process for producing single-wall nanotubes (SWNTs) are described.

Modelling nitrogen and phosphorus loads in a Mediterranean river catchment (La Tordera, NE Spain)

Human activities have resulted in increased nutrient levels in many rivers all over Europe. Sustainable management of river basins demands an assessment of the causes and consequences of human alteration of nutrient flows, together with an evaluation of management options. In the context of an integrated and interdisciplinary environmental assessment (IEA) of nutrient flows, we present and discuss the application of the nutrient emission model MONERIS (MOdelling Nutrient Emissions into River Systems) to the Catalan river basin, La Tordera (north-east Spain), for the period 1996–2002. After a successful calibration and verification process (Nash-Sutcliffe efficiencies E=0.85 for phosphorus and E=0.86 for nitrogen), the application of the model MONERIS proved to be useful in estimating nutrient loads. Crucial for model calibration, in-stream retention was estimated to be about 50 % of nutrient emissions on an annual basis. Through this process, we identified the importance of point sources for phosphorus emissions (about 94% for 1996–2002), and diffuse sources, especially inputs via groundwater, for nitrogen emissions (about 31% for 1996–2002). Despite hurdles related to model structure, observed loads, and input data encountered during the modelling process, MONERIS provided a good representation of the major interannual and spatial patterns in nutrient emissions. An analysis of the model uncertainty and sensitivity to input data indicates that the model MONERIS, even in data-starved Mediterranean catchments, may be profitably used by water managers for evaluating quantitative nutrient emission scenarios for the purpose of managing river basins. As an example of scenario modelling, an analysis of the changes in nutrient emissions through two different future scenarios allowed the identification of a set of relevant measures to reduce nutrient loads.

Degradação de BTXs via processos oxidativos avançados

In this study the efficiency of advanced oxidative processes (AOPs) were investigated toward the degradation of aqueous solutions containing benzene, toluene and xylenes (BTX). The results indicated that BTX can be effectively oxidized by the UV-A-assisted photo-Fenton process. The treatment permits almost total degradation of BTX and removal of more than 80% of the phenolyc intermediates at reaction times of about 30 min. Preliminary investigations using solar light suggest a good potentiality of the process for the treatment of large volumes of aqueous samples containing these polluting species.

Improving Evaluation and Development Capability in Verification and Validation

Validation and verification operations encounter various challenges in product development process. Requirements for increasing the development cycle pace set new requests for component development process. Verification and validation usually represent the largest activities, up to 40 50 % of R&D resources utilized. This research studies validation and verification as part of case company's component development process. The target is to define framework that can be used in improvement of the validation and verification capability evaluation and development in display module development projects. Validation and verification definition and background is studied in this research. Additionally, theories such as project management, system, organisational learning and causality is studied. Framework and key findings of this research are presented. Feedback system according of the framework is defined and implemented to the case company. This research is divided to the theory and empirical parts. Theory part is conducted in literature review. Empirical part is done in case study. Constructive methode and design research methode are used in this research A framework for capability evaluation and development was defined and developed as result of this research. Key findings of this study were that double loop learning approach with validation and verification V+ model enables defining a feedback reporting solution. Additional results, some minor changes in validation and verification process were proposed. There are a few concerns expressed on the results on validity and reliability of this study. The most important one was the selected research method and the selected model itself. The final state can be normative, the researcher may set study results before the actual study and in the initial state, the researcher may describe expectations for the study. Finally reliability of this study, and validity of this work are studied.

Pharmaceuticals occurrence in a WWTP with significant industrial contribution and its input into the river system

Occurrence and removal of 81 representative Pharmaceutical Active Compounds (PhACs) were assessed in a municipal WWTP located in a highly industrialized area, with partial water reuse after UV tertiary treatment and discharge to a Mediterranean river. Water monitoring was performed in an integrated way at different points in the WWTP and river along three seasons. Consistent differences between therapeutic classes were observed in terms of influent concentration, removal efficiencies and seasonal variation. Conventional (primary and secondary) treatment was unable to completely remove numerous compounds and UV-based tertiary treatment played a complementary role for some of them. Industrial activity influence was highlighted in terms of PhACs presence and seasonal distribution. Even if global WWTP effluent impact on the studied river appeared to be minor, PhACs resulted widespread pollutants in river waters. Contamination can be particularly critical in summer in water scarcity areas, when water flow decreases considerably

Uso da cinza da casca do arroz (CCA) obtida da geração de energia térmica como adsorvente de Zn(II) em soluções aquosas

The removal study was conducted using 1.00 g of the rice husk ash (RHA) and 20.0 mL solution with concentrations in the range of 10-1000 mg/L of Zn(II). The influence of contact time, initial metal concentration, agitation and pH of the removal process was investigated. Superior removals to 95% were obtained at the end of 24 h of contact. The agitation increased in 20% the removal of Zn(II), being needed only 5 min to reach the equilibrium. The adsorption process was studied by the models of isotherms of Langmuir, Freundlich and BET, obtaining results of R L and 1/n for a process favorable of adsorption. BET isotherm best represents the equilibrium adsorption. The results showed that the RHA has the largest capacity and affinity for the removal of Zn(II).

Remoção de compostos orgânicos em água empregando carvão ativado impregnado com óxido de ferro: ação combinada de adsorção e oxidação em presença de H2O2

In this work, composites based on activated carbon/iron oxide (AC/Fe) were prepared in two different proportions (AC/Fe 5/1 and 1/1) and evaluated in the removal of the organic dye methylene blue (MB). Physical-chemical properties of the composites were determined by X-ray diffraction (XRD), adsorption/dessorption of N2 isotherm, temperature programmed reduction (TPR) and scanning electron microscopy (SEM). Results showed that goethite (α- FeOOH), with nanometer particle size, was formed over carbon surface for both composites. These materials showed high efficiency to remove MB from solution by combined adsorption and oxidation process. The AC/Fe 1/1 showed to be more active in (MB) oxidation then AC/Fe 5/1.

Ultrafiltration membranes from waste polyethylene terephthalate and additives: synthesis and characterization

The synthesis and characterization of asymmetric ultrafiltration membranes from recycled polyethylene terephthalate (PET) and polyvinylpyrrolidone (PVP) is reported. PET is currently used in many applications, including the manufacture of bottles and tableware. Monomer extraction from waste PET is expensive, and this process has not yet been successfully demonstrated on a viable scale. Hence, any method to recycle or regenerate PET once it has been used is of significant importance from scientific and environmental research viewpoints. Such a process would be a green alternative due to reduced raw monomer consumption and the additional benefit of reduced manufacturing costs. The membranes described here were prepared by a phase-inversion process, which involved casting a solution containing PET, m-cresol as solvent, and polyethylene glycol (PEG) of different molecular weights as additives. The membranes were characterized in terms of pure water permeability (PWP), molecular weight cut-off (MWCO), and flux and membrane morphology. The results show that the addition of PEG with high molecular weights leads to membranes with higher PWP. The presence of additives affects surface roughness and membrane morphology.

Natural colonization of leaves of 'Pêra' sweet orange and related varieties by Guignardia citricarpa

The purpose of this research was to evaluate the differences in the colonization and production of structures in the leaves of 'Pêra' sweet orange (Citrus sinensis) clones and related varieties by Guignardia citricarpa. The natural colonization and the production of reproductive structures in the leaves and in vitro of ten 'Pêra' sweet orange was quantified in the following clones: Bianchi, Dibbern C.V., EEL, IAC 2000, Olímpia 15161, Premunizada 1212, Premunizada 1743/82, R. Gullo 1569/244, R. Gullo 1570/246 and Vimusa; and in five related varieties: Redonda C.N, Ovale 968, Ovale San Lio 969, Lamb Summer and Corsa Tardia. The quantification of the colonization density of G. citricarpa in the leaves was obtained through isolation. Incidence and colonization density (cm²) were calculated for each clone. The production of reproductive structures was accomplished through the moistening and drying process of the leaves. The incidence (percentage of affected leaves) and the leaf surface percentage occupied by the reproductive fungus structures were quantified. The in vitro production of reproductive structures was accomplished in water-agar medium. The number of immature and total reproductive fungus structures (cm²), and the percentage of picnidia with liberation of spores were quantified. Significant differences were not observed among clones related to the colonization of the leaves. But there were differences in the induction experiments, i.e., in the leaf surface percentage occupied by the reproductive fungus structures and the in vitro production of reprodutive fungus structures.

The Methods of Possible Joint Treatment of Manure and Sewage Sludge in the Leningrad Region

The nutrient load to the Gulf of Finland has started to increase as a result of the strong economic recovery in agriculture and livestock farming in the Leningrad region. Also sludge produced from municipal wastewater treatment plant of the Leningrad region causes the great impact on the environment, but still the main options for its treatment is disposal on the sludge beds or Landfills. The aim of this study was to evaluate the implementation of possible joint treatment methods of manure form livestock and poultry enterprises and sewage sludge produced from municipal wastewater treatment plants in the Leningrad region. The study is based on published data. The most attention was put on the anaerobic digestion and incineration methods. The manure and sewage sludge generation for the whole Leningrad region and energy potential produced from their treatment were estimated. The calculations showed that total amount of sewage sludge generation is 1 348 000 t/a calculated on wet matter and manure generation is 3 445 000 t/a calculated on wet matter. The potential heat release from anaerobic digestion process and incineration process is 4 880 000 GJ/a and 5 950 000 GJ/a, respectively. Furthermore, the work gives the overview of the general Russian and Finnish legislation concerning manure and sewage sludge treatment. In the Gatchina district it was chosen the WWTP and livestock and poultry enterprises for evaluation of the centralized treatment plant implementation based on anaerobic digestion and incineration methods. The electricity and heat power of plant based on biogas combustion process is 4.3 MW and 7.8 MW, respectively. The electricity and heat power of plant based on manure and sewage sludge incineration process is 3.0 MW and 6.1 MW, respectively.

Assessment of Coals from Russia and Countries of Former Soviet Union for Utility Fluidized Bed Boilers

With the occurrence of fossil fuels such as oil, gas and coal we found new sources of energy that have played a critical role in the progress of our modern society. Coal is very ample compared to the other two fossil fuels. Global coal reserves at the end of 2005 were estimated at 847,5 billion tones. Along with the major energy sources, coal is the most fast growing fuel on a global basis, it provides 26% of primary energy needs and remains essential to the economies of many developed and developing countries. Coal-fired power generation accounts for 41% of the world‘s total electricity production and in some countries, such as South Africa, Poland, China, Australia, Kazakhstan and India is on very high level. Still, coal utilization represents challenges related to high emissions of air pollutants such as sulphur and nitrogen dioxides, particulate matter, mercury and carbon dioxide. In relation to these a number of technologies have been developed and are in marketable use, with further potential developments towards ―Near Zero Emission‖ coal plants. In present work, coals mined in Russia and countries of Former Soviet Union were reviewed. Distribution of coal reserves on the territory of Russia and the potential for power generation from coal-fired plants across Russia was shown. Physical and chemical properties of coals produced were listed and examined, as main factor influencing on design of the combustion facility and incineration process performance. The ash-related problems in coal-fired boilers were described. The analysis of coal ash of Russia and countries of Former Soviet Union were prepared. Feasible combustion technologies also were reviewed.

Finnair Technical Procurement’s Processes and Service Quality

As primary objective, this thesis examines Finnair Technical Procurement’s service quality with its underlying process. As an internal unit, Technical Procurement serves as a link between external suppliers and internal customers. It is argued that external service quality requires a certain quality level within an organization. At the same time, aircraft maintenance business is subject to economic restraints. Therefore, a methodology was developed with a modified House of Quality that assists management in analyzing and evaluating Technical Procurement’s service level and connected process steps. It could be shown that qualitative and quantitative objectives do not exclude each other per se.

Promoting Programming Learning. Engagement, Automatic Assessment with Immediate Feedback in Visualizations

The skill of programming is a key asset for every computer science student. Many studies have shown that this is a hard skill to learn and the outcomes of programming courses have often been substandard. Thus, a range of methods and tools have been developed to assist students’ learning processes. One of the biggest fields in computer science education is the use of visualizations as a learning aid and many visualization based tools have been developed to aid the learning process during last few decades. Studies conducted in this thesis focus on two different visualizationbased tools TRAKLA2 and ViLLE. This thesis includes results from multiple empirical studies about what kind of effects the introduction and usage of these tools have on students’ opinions and performance, and what kind of implications there are from a teacher’s point of view. The results from studies in this thesis show that students preferred to do web-based exercises, and felt that those exercises contributed to their learning. The usage of the tool motivated students to work harder during their course, which was shown in overall course performance and drop-out statistics. We have also shown that visualization-based tools can be used to enhance the learning process, and one of the key factors is the higher and active level of engagement (see. Engagement Taxonomy by Naps et al., 2002). The automatic grading accompanied with immediate feedback helps students to overcome obstacles during the learning process, and to grasp the key element in the learning task. These kinds of tools can help us to cope with the fact that many programming courses are overcrowded with limited teaching resources. These tools allows us to tackle this problem by utilizing automatic assessment in exercises that are most suitable to be done in the web (like tracing and simulation) since its supports students’ independent learning regardless of time and place. In summary, we can use our course’s resources more efficiently to increase the quality of the learning experience of the students and the teaching experience of the teacher, and even increase performance of the students. There are also methodological results from this thesis which contribute to developing insight into the conduct of empirical evaluations of new tools or techniques. When we evaluate a new tool, especially one accompanied with visualization, we need to give a proper introduction to it and to the graphical notation used by tool. The standard procedure should also include capturing the screen with audio to confirm that the participants of the experiment are doing what they are supposed to do. By taken such measures in the study of the learning impact of visualization support for learning, we can avoid drawing false conclusion from our experiments. As computer science educators, we face two important challenges. Firstly, we need to start to deliver the message in our own institution and all over the world about the new – scientifically proven – innovations in teaching like TRAKLA2 and ViLLE. Secondly, we have the relevant experience of conducting teaching related experiment, and thus we can support our colleagues to learn essential know-how of the research based improvement of their teaching. This change can transform academic teaching into publications and by utilizing this approach we can significantly increase the adoption of the new tools and techniques, and overall increase the knowledge of best-practices. In future, we need to combine our forces and tackle these universal and common problems together by creating multi-national and multiinstitutional research projects. We need to create a community and a platform in which we can share these best practices and at the same time conduct multi-national research projects easily.