Neutralización y protección ocular en el deporte.

Monográfico con el título: 'Visión y deporte'. Resumen tomado de la publicación

Microstructure and magnetic properties of Ni50 Mn37 Sn13 Heusler alloy ribbons

The Heusler alloy Ni50 Mn37 Sn13 was successfully produced as ribbon flakes of thickness around 7-10 μm melt spinning. Fracture cross section micrographs in the ribbon show the formation of a microcrystalline columnarlike microstructure, with their longer axes perpendicular to the ribbon plane. Phase transition temperatures of the martensite-austenite transformation were found to be MS =218 K, Mf =207 K, AS =224 K, and Af =232 K; the thermal hysteresis of the transformation is 15 K. Ferromagnetic L 21 bcc austenite phase shows a Curie point of 313 K, with cell parameter a=0.5971 (5) nm at 298 K, transforming into a modulated 7M orthorhombic martensite with a=0.6121 (7) nm, b=0.6058 (8) nm, and c=0.5660 (2) nm, at 150 K

Effect of supplementation with MgCO3 and L-tryptophan on the welfare and on the carcass and meat quality of two halothane pig genotypes (NN and nn)

Sixty-one animals with different Halothane genes (homozygous halothane positive, n=34; and homozygous halothane negative, n=27) were fed with three diets (controlgroup, with no supplement; magnesium (Mg) group with 1.28g MgCO3/kg and tryptophan (Trp) group with 5g L-Trp/kg) during the last 5 days before slaughter. Animals were submitted to minimal stress ante mortem conditions. Pig behaviour was recorded at the experimental farm, raceway to the CO2 stunning system and during the stunning period. Corneal reflexes were recorded after stunning as well. There were no differences in feed intake among diets (p>0.05) during the 5 days of treatment. The halothane positive (nn) group had lower intake than the halothane negative (NN) group (p<0.01). The behaviour of the pigs in the raceway did not differ (p>0.05) among treatments or halothane genotype. A significant (p<0.001) interaction diet*halothane was found in the time to appear the first retreat attempt during the exposure to the CO2 system. In the nn group, the time of performing the first retreat attempt was later in the Mg (p<0.05) than the Control group. Moreover, in the Mg group, the nn had a later (p<0.05) first retreat attempt than the NN. Thus, Mg supplementation could have a positive effect on welfare of nn pigs. The nn had a lower proportion of animals that showed corneal reflexes after stunning than NN, indicating a higher effectiveness of the stunning method in nn pigs. Neither Mg nor Trp affected carcass quality and meat quality parameters, although significant differences were found between genotypes

Revaloració de la fracció cel·lular de la sang de porc procedent d'escorxadors industrials

La sang de porc és un subproducte comestible que es genera als escorxadors industrials durant el procés d'obtenció de la canal. Aquest subproducte es caracteritza per presentar una elevada càrrega contaminant i, degut a l'elevat volum que es genera, és necessari trobar estratègies que permetin la seva revaloració i aprofitament, a la vegada que disminuïm la contaminació ambiental i les despeses que es deriven del seu processament abans de l'abocament. La fracció cel·lular (FC) constitueix el 40 % de la sang de porc i conté principalment l'hemoglobina (Hb), que representa al voltant del 90 % del contingut en proteïna d'aquesta fracció (un 35 % aproximadament). L'elevat percentatge en proteïna i en ferro, i les seves bones propietats funcionals fan que l'aprofitament d'aquest subproducte com a primera matèria o ingredient de la indústria alimentària sigui una alternativa molt útil a l'hora de reduir les despeses de la indústria càrnia, sempre que es resolguin els problemes de l'enfosquiment i dels sabors estranys que pot conferir la FC quan s'addiciona a productes alimentaris. Una altra possible utilització de la FC és aprofitar les propietats colorants de l'Hb o del grup hemo, com a colorant d'origen natural en diversos productes alimentaris. Els objectius del present treball eren, en primer lloc, determinar les millors condicions d'aplicació del procés de conservació de la FC mitjançant la deshidratació per atomització i caracteritzar físico-químicament i microbiològica el concentrat d'Hb en pols. En segon lloc, avaluar l'eficàcia de diferents additius antioxidants i/o segrestants del ferro per prevenir l'enfosquiment que pateix la FC durant la deshidratació. En tercer lloc, aplicar tractaments d'altes pressions hidrostàtiques com a procés d'higienització i avaluar els efectes d'aquest tractament sobre la microbiota contaminant, el color i les propietats funcionals de la FC. Finalment, desenvolupar un procés d'obtenció d'hidrolitzats proteics descolorats a partir de l'Hb amb la finalitat d'utilitzar-los com a ingredients nutricionals i/o funcionals. La millor temperatura de deshidratació per atomització de la FC hemolitzada era 140ºC. La FC en pols presentava un contingut en humitat del 5,3 % i un percentatge de solubilitat proteica del 96 %. La deshidratació per atomització induïa canvis en l'estructura nativa de l'Hb i, per tant, un cert grau de desnaturalització que pot conduir a una disminució de les seves propietats funcionals. L'extracte sec de la FC en pols estava composat per un 94,6 % de proteïna, un 3 % de sals minerals i un 0,7 % de greix. Els valors CIE L*a*b* del color de la FC en pols eren força constants i reflectien el color vermell marró fosc d'aquesta, a causa de l'oxidació del ferro hèmic que es produeix durant la deshidratació. La càrrega contaminant de la FC fresca de la sang de porc era força elevada i el tractament d'hemòlisi amb ultrasons i la centrifugació posterior no produïen una reducció significativa de la microbiota contaminant, obtenint un producte amb uns recomptes microbiològics de l'ordre de 106 ufc·mL-1. La deshidratació per atomització produïa una disminució d'una unitat logarítmica dels recomptes totals de la FC hemolitzada. Tanmateix, el producte en pols encara reflectia l'elevada contaminació de la primera matèria, fet que condiciona negativament la seva utilització com a ingredient alimentari, a no ser que es millorin les condicions de recollida de la sang a l'escorxador o que aquesta o la FC es sotmeti a algun tractament d'higienització prèviament a la deshidratació. Les isotermes de sorció a 20ºC de la FC en pols tenien forma sigmoïdal i una histèresi estreta i llarga. L'equació GAB és un bon model matemàtic per ajustar les dades de sorció obtingudes experimentalment i determinar la isoterma d'adsorció de la FC deshidratada per atomització. El percentatge d'humitat de la FC deshidratada a 140ºC es corresponia a un valor d'aw a 20 ºC d'aproximadament el 0,16. Tenint en compte que estava per sota dels valors d'aw corresponents a la capa monomolecular, es pot garantir la conservació a temperatura ambient del producte, sempre que s'envasi en recipients tancats que no permetin l'entrada d'humitat de l'exterior. De l'estudi de la possible estabilització del color de la FC deshidratada per atomització mitjançant l'addició d'antioxidants i/o segrestants de ferro, es va observar que només l'àcid ascòrbic, la glucosa, l'àcid nicotínic i la nicotinamida, tenien efectes positius sobre el color del producte en pols. L'ascòrbic i la glucosa no milloraven la conservació del color de l'Hb però disminuïen l'enfosquiment que es produeix durant la deshidratació, amb la qual cosa es pot obtenir un producte en pols de color marró més clar. L'addició de dextrina o L-cisteïna no disminuïa l'enfosquiment ni evitava el canvi de color de l'Hb. L'àcid nicotínic i la nicotinamida protegien el color de l'Hb durant el procés de deshidratació i l'emmagatzematge de la FC en pols. Les millors condicions d'aplicació del tractament amb altes pressions hidrostàtiques (HHP) sobre la FC eren 400 MPa, a 20ºC, durant 15 minuts, perquè produïen una millora significativa de la qualitat microbiològica, no afectaven negativament al color, no comprometien gaire la solubilitat proteica l'Hb i, malgrat que produïen un augment de la viscositat, la FC romania fluida després del tractament. Aquest tractament permetia una reducció de la microbiota contaminant de la FC d'entre 2 i 3 unitats logarítmiques. L'aplicació de l'alta pressió i la posterior deshidratació per atomització permetien obtenir un producte en pols amb recomptes totals de l'ordre de 2,8 unitats logarítmiques. El color de la FC pressuritzada en pols era igual que el de la FC control deshidratada, perquè ambdues mostres presentaven la mateixa susceptibilitat a l'oxidació del grup hemo produïda per la deshidratació. L'alta pressió incrementava la susceptibilitat de l'Hb als efectes desnaturalitzants de la deshidratació, fonamentalment a pH 7 (PIE), ja que es va observar una disminució de la solubilitat proteica a pH neutre després dels 2 processos tecnològics. La FC en pols presentava una màxima capacitat escumant al PIE de l'Hb. L'aplicació del tractament HHP produïa una disminució de la capacitat escumant de la FC en pols, però no tenia efectes negatius sobre l'estabilitat de l'escuma formada. Tampoc es van observar efectes negatius del tractament HHP sobre l'activitat emulsionant de l'Hb. La màxima activitat emulsionant de l'Hb s'aconseguia amb una concentració de FC en pols de l'1,5 % a pH 7 i de l'1 % a pH 4,5. Les pastes obtingudes per escalfament de la FC presentaven característiques molt diferenciades depenent del pH. A pH neutre es formaven unes pastes dures i consistents, mentre que a pH àcid les pastes eren poc consistents, molt adhesives i més elàstiques que les anteriors. Aquestes tenien una capacitat de retenció d'aigua molt superior que les de pH 7, en les quals l'aigua quedava retinguda per capil·laritat. La textura i capacitat de retenció d'aigua de les pastes tampoc eren afectades pel tractament HHP. El tractament HHP incrementava l'activitat de la Tripsina sobre l'Hb quan el substrat i l'enzim es tractaven conjuntament i afavoria el procés d'obtenció d'hidrolitzats descolorats a partir de la FC, la qual cosa permetia assolir el mateix grau de descoloració amb una dosi d'enzim inferior. El tractament d'hidròlisi de la FC amb la utilització combinada de Tripsina seguida d'un tractament amb Pepsina permetia l'obtenció d'un hidrolitzat proteic d'Hb descolorat i hidrolitzava completament la globina, donant lloc a 2 pèptids de 10,8 i 7,4 KDa. Val a dir que també produïa un 60 80 % de nitrogen soluble en TCA, constituït fonamentalment per pèptids petits i aminoàcids lliures. Els hidrolitzats trípsics i pèpsics d'Hb, obtinguts a partir de FC no pressuritzada i deshidratats per atomització a 180ºC, eren de color blanc i tenien un contingut en humitat del 4,7 %, un 84,2 % de proteïna i 9,7 % de sals minerals. El procés d'hidròlisi permetia una reducció considerable de la contaminació de la FC, obtenint un producte en pols amb uns recomptes totals de l'ordre de 102-103 ufc·g-1. Pel que fa a la funcionalitat dels hidrolitzats d'Hb deshidratats per atomització, aquests presentaven una elevada solubilitat proteica a pH 5 i 7 i romanien solubles després d'un escalfament a 80ºC durant 30 min. Tanmateix, aquesta hidròlisi afectava molt negativament la capacitat de mantenir escumes estables i l'activitat emulsionant.

Modelling, control and supervision for a class of hybrid systems

The aim of this thesis is to narrow the gap between two different control techniques: the continuous control and the discrete event control techniques DES. This gap can be reduced by the study of Hybrid systems, and by interpreting as Hybrid systems the majority of large-scale systems. In particular, when looking deeply into a process, it is often possible to identify interaction between discrete and continuous signals. Hybrid systems are systems that have both continuous, and discrete signals. Continuous signals are generally supposed continuous and differentiable in time, since discrete signals are neither continuous nor differentiable in time due to their abrupt changes in time. Continuous signals often represent the measure of natural physical magnitudes such as temperature, pressure etc. The discrete signals are normally artificial signals, operated by human artefacts as current, voltage, light etc. Typical processes modelled as Hybrid systems are production systems, chemical process, or continuos production when time and continuous measures interacts with the transport, and stock inventory system. Complex systems as manufacturing lines are hybrid in a global sense. They can be decomposed into several subsystems, and their links. Another motivation for the study of Hybrid systems is the tools developed by other research domains. These tools benefit from the use of temporal logic for the analysis of several properties of Hybrid systems model, and use it to design systems and controllers, which satisfies physical or imposed restrictions. This thesis is focused in particular types of systems with discrete and continuous signals in interaction. That can be modelled hard non-linealities, such as hysteresis, jumps in the state, limit cycles, etc. and their possible non-deterministic future behaviour expressed by an interpretable model description. The Hybrid systems treated in this work are systems with several discrete states, always less than thirty states (it can arrive to NP hard problem), and continuous dynamics evolving with expression: with Ki ¡ Rn constant vectors or matrices for X components vector. In several states the continuous evolution can be several of them Ki = 0. In this formulation, the mathematics can express Time invariant linear system. By the use of this expression for a local part, the combination of several local linear models is possible to represent non-linear systems. And with the interaction with discrete events of the system the model can compose non-linear Hybrid systems. Especially multistage processes with high continuous dynamics are well represented by the proposed methodology. Sate vectors with more than two components, as third order models or higher is well approximated by the proposed approximation. Flexible belt transmission, chemical reactions with initial start-up and mobile robots with important friction are several physical systems, which profits from the benefits of proposed methodology (accuracy). The motivation of this thesis is to obtain a solution that can control and drive the Hybrid systems from the origin or starting point to the goal. How to obtain this solution, and which is the best solution in terms of one cost function subject to the physical restrictions and control actions is analysed. Hybrid systems that have several possible states, different ways to drive the system to the goal and different continuous control signals are problems that motivate this research. The requirements of the system on which we work is: a model that can represent the behaviour of the non-linear systems, and that possibilities the prediction of possible future behaviour for the model, in order to apply an supervisor which decides the optimal and secure action to drive the system toward the goal. Specific problems can be determined by the use of this kind of hybrid models are: - The unity of order. - Control the system along a reachable path. - Control the system in a safe path. - Optimise the cost function. - Modularity of control The proposed model solves the specified problems in the switching models problem, the initial condition calculus and the unity of the order models. Continuous and discrete phenomena are represented in Linear hybrid models, defined with defined eighth-tuple parameters to model different types of hybrid phenomena. Applying a transformation over the state vector : for LTI system we obtain from a two-dimensional SS a single parameter, alpha, which still maintains the dynamical information. Combining this parameter with the system output, a complete description of the system is obtained in a form of a graph in polar representation. Using Tagaki-Sugeno type III is a fuzzy model which include linear time invariant LTI models for each local model, the fuzzyfication of different LTI local model gives as a result a non-linear time invariant model. In our case the output and the alpha measure govern the membership function. Hybrid systems control is a huge task, the processes need to be guided from the Starting point to the desired End point, passing a through of different specific states and points in the trajectory. The system can be structured in different levels of abstraction and the control in three layers for the Hybrid systems from planning the process to produce the actions, these are the planning, the process and control layer. In this case the algorithms will be applied to robotics ¡V a domain where improvements are well accepted ¡V it is expected to find a simple repetitive processes for which the extra effort in complexity can be compensated by some cost reductions. It may be also interesting to implement some control optimisation to processes such as fuel injection, DC-DC converters etc. In order to apply the RW theory of discrete event systems on a Hybrid system, we must abstract the continuous signals and to project the events generated for these signals, to obtain new sets of observable and controllable events. Ramadge & Wonham¡¦s theory along with the TCT software give a Controllable Sublanguage of the legal language generated for a Discrete Event System (DES). Continuous abstraction transforms predicates over continuous variables into controllable or uncontrollable events, and modifies the set of uncontrollable, controllable observable and unobservable events. Continuous signals produce into the system virtual events, when this crosses the bound limits. If this event is deterministic, they can be projected. It is necessary to determine the controllability of this event, in order to assign this to the corresponding set, , controllable, uncontrollable, observable and unobservable set of events. Find optimal trajectories in order to minimise some cost function is the goal of the modelling procedure. Mathematical model for the system allows the user to apply mathematical techniques over this expression. These possibilities are, to minimise a specific cost function, to obtain optimal controllers and to approximate a specific trajectory. The combination of the Dynamic Programming with Bellman Principle of optimality, give us the procedure to solve the minimum time trajectory for Hybrid systems. The problem is greater when there exists interaction between adjacent states. In Hybrid systems the problem is to determine the partial set points to be applied at the local models. Optimal controller can be implemented in each local model in order to assure the minimisation of the local costs. The solution of this problem needs to give us the trajectory to follow the system. Trajectory marked by a set of set points to force the system to passing over them. Several ways are possible to drive the system from the Starting point Xi to the End point Xf. Different ways are interesting in: dynamic sense, minimum states, approximation at set points, etc. These ways need to be safe and viable and RchW. And only one of them must to be applied, normally the best, which minimises the proposed cost function. A Reachable Way, this means the controllable way and safe, will be evaluated in order to obtain which one minimises the cost function. Contribution of this work is a complete framework to work with the majority Hybrid systems, the procedures to model, control and supervise are defined and explained and its use is demonstrated. Also explained is the procedure to model the systems to be analysed for automatic verification. Great improvements were obtained by using this methodology in comparison to using other piecewise linear approximations. It is demonstrated in particular cases this methodology can provide best approximation. The most important contribution of this work, is the Alpha approximation for non-linear systems with high dynamics While this kind of process is not typical, but in this case the Alpha approximation is the best linear approximation to use, and give a compact representation.

The variation in transparency of amniotic membrane used in ocular surface regeneration

Background/aims: Scant consideration has been given to the variation in structure of the human amniotic membrane (AM) at source or to the significance such differences might have on its clinical transparency. Therefore, we applied our experience of quantifying corneal transparency to AM. Methods: Following elective caesarean, AM from areas of the fetal sac distal and proximal (ie, adjacent) to the placenta was compared with freeze-dried AM. The transmission of light through the AM samples was quantified spectrophotometrically; also, tissue thickness was measured by light microscopy and refractive index by refractometry. Results: Freeze-dried and freeze-thawed AM samples distal and proximal to the placenta differed significantly in thickness, percentage transmission of visible light and refractive index. The thinnest tissue (freeze-dried AM) had the highest transmission spectra. The thickest tissue (freeze-thawed AM proximal to the placenta) had the highest refractive index. Using the direct summation of fields method to predict transparency from an equivalent thickness of corneal tissue, AM was found to be up to 85% as transparent as human cornea. Conclusion: When preparing AM for ocular surface reconstruction within the visual field, consideration should be given to its original location from within the fetal sac and its method of preservation, as either can influence corneal transparency.

Displacement of Zn through acidic light-textured soils

In order to gain understanding of the movement of pollutant metals in soil. the chemical mechanisms involved in the transport of zinc were studied. The displacement of zinc through mixtures of sand and cation exchange resin was measured to validate the methods used for soil. With cation exchange capacities of 2.5 and 5.0 cmol(c) kg(-1). 5.6 and 8.4 pore volumes of 10 mM CaCl2, respectively, were required to displace a pulse of ZnCl2. A simple Burns-type model (Wineglass) using an adsorption coefficient (K-d) determined by fitting a straight line relationship to an adsorption isotherm gave a good fit to the data (K-d=0.73 and 1.29 ml g(-1), respectively). Surface and subsurface samples of an acidic sandy loam (organic matter 4.7 and 1.0%. cation exchange capacity (CEC) 11.8 and 6.1 cmol(c) kg(-1) respectively) were leached with 10 mM calcium chloride. nitrate and perchlorate. With chloride. the zinc pulse was displaced after 25 and 5 pore volumes, respectively. The Kd values were 6.1 and 2.0 ml g(-1). but are based on linear relationships fitted to isotherms which are both curved and show hysteresis. Thus. a simple model has limited value although it does give a general indication of rate of displacement. Leaching with chloride and perchlorate gave similar displacement and Kd values, but slower movement occurred with nitrate in both soil samples (35 and 7 pore volumes, respectively) which reflected higher Kd values when the isotherms were measured using this anion (7.7 and 2.8 ml g(-1) respectively). Although pH values were a little hi-her with nitrate in the leachates, the differences were insufficient to suggest that this increased the CEC enough to cause the delay. No increases in pH occurred with nitrate in the isotherm experiments. Geochem was used to calculate the proportions of Zn complexed with the three anions and with fulvic acid determined from measurements of dissolved organic matter. In all cases, more than 91% of the Zn was present as Zn2+ and there were only minor differences between the anions. Thus, there is an unexplained factor associated with the greater adsorption of Zn in the presence of nitrate. Because as little as five pore volumes of solution displaced Zn through the subsurface soil, contamination of ground waters may be a hazard where Zn is entering a light-textured soil, particularly where soil salinity is increased. Reductions in organic matter content due to cultivation will increase the hazard. (C) 2004 Elsevier B.V. All rights reserved.

Differentiation status of limbal epithelial cells cultured on intact and denuded amniotic membrane before and after air-lifting

We have investigated differences in bovine limbal epithelial cell differentiation when expanded upon intact (amniotic epithelial cells and basement membrane remaining) and denuded human amniotic membrane, a commonly used substrate in ophthalmic surgery for corneal stem cell transplantation. Ex vivo expansion of the epithelial cells, in supplemented media, continued for 2 weeks followed by 1 week under ‘air-lifting’ conditions. Before and after air-lifting the differentiated (K3/K12 positive) and undifferentiated (K14 positive) cells were quantified by immunohistochemistry, Western blotting and quantitative PCR. Limbal epithelial cells expanded upon amniotic membrane formed 4-6 stratified layers, both on intact and denuded amniotic membrane. On denuded amniotic membrane the proportion of differentiated cells remained unaltered following airlifting. Within cells grown on intact amniotic membrane, however, the number of differentiated cells increased significantly following air-lifting. These results have important implications for both basic and clinical research. Firstly, they show that bovine limbal epithelia can be used as an alternative source of cells for basic research investigating ex vivo limbal stem cells expansion. Secondly, these findings serve as a warning to clinicians that the affect of amniotic membrane on transplantable cells is not fully understood; the use of intact or denuded amniotic membrane can produce different results in terms of the amount of differentiation, once cells are exposed to the air.

Bayesian analysis of an inverse Gaussian correlated frailty model

In survival analysis frailty is often used to model heterogeneity between individuals or correlation within clusters. Typically frailty is taken to be a continuous random effect, yielding a continuous mixture distribution for survival times. A Bayesian analysis of a correlated frailty model is discussed in the context of inverse Gaussian frailty. An MCMC approach is adopted and the deviance information criterion is used to compare models. As an illustration of the approach a bivariate data set of corneal graft survival times is analysed. (C) 2006 Elsevier B.V. All rights reserved.

Exploring the applications of a pulsating jet hydrodynamic modulated voltammetric (HMV) system - electrochemistry of nanostructured Pt electrodes and trace analysis

The electrochemistry of nanostructured electrodes is investigated using hydrodynamic modulated voltammetry (HMV). Here a liquid crystal templating process is used to produce a platinum modified electrode with a relatively high surface area (Roughness factor, Rf = 42.4). The electroreduction of molecular oxygen at a nanostructured platinum surface is used to demonstrate the ability of HMV to discriminate between Faradaic and non-Faradaic electrode reactions. The HMV approach shows that the reduction of molecular oxygen shows considerable hysteresis correlating with the formation and stripping of oxide species at the platinum surface. Without the HMV analysis it is difficult to discern the same detail under the conditions employed. In addition the detection limit of the apparatus is explored and shown, under ideal conditions, to be of the order of 45 nmol dm(-3) employing [Fe(CN)(6)](4-) as a test species. (C) 2009 Elsevier B.V. All rights reserved.

Liposomes and skin: From drug delivery to model membranes

The early eighties saw the introduction of liposomes as skin drug delivery systems, initially promoted primarily for localised effects with minimal systemic delivery. Subsequently, a novel ultradeformable vesicular system (termed "Transfersomes" by the inventors) was reported for transdermal delivery with an efficiency similar to subcutaneous injection. Further research illustrated that the mechanisms of liposome action depended on the application regime and the vesicle composition and morphology. Ethical, health and supply problems with human skin have encouraged researchers to use skin models. 'IYaditional models involved polymer membranes and animal tissue, but whilst of value for release studies, such models are not always good mimics for the complex human skin barrier, particularly with respect to the stratum corneal intercellular lipid domains. These lipids have a multiply bilayered organization, a composition and organization somewhat similar to liposomes, Consequently researchers have used vesicles as skin model membranes. Early work first employed phospholipid liposomes and tested their interactions with skin penetration enhancers, typically using thermal analysis and spectroscopic analyses. Another approach probed how incorporation of compounds into liposomes led to the loss of entrapped markers, analogous to "fluidization" of stratum corneum lipids on treatment with a penetration enhancer. Subsequently scientists employed liposomes formulated with skin lipids in these types of studies. Following a brief description of the nature of the skin barrier to transdermal drug delivery and the use of liposomes in drug delivery through skin, this article critically reviews the relevance of using different types of vesicles as a model for human skin in permeation enhancement studies, concentrating primarily on liposomes after briefly surveying older models. The validity of different types of liposome is considered and traditional skin models are compared to vesicular model membranes for their precision and accuracy as skin membrane mimics. (c) 2008 Elsevier B.V. All rights reserved.

Plastic compression of a collagen gel forms a much improved scaffold for ocular surface tissue engineering over conventional collagen gels

We compare the use of plastically compressed collagen gels to conventional collagen gels as scaffolds onto which corneal limbal epithelial cells (LECs) are seeded to construct an artificial corneal epithelium. LECs were isolated from bovine corneas (limbus) and seeded onto either conventional uncompressed or novel compressed collagen gels and grown in culture. Scanning electron microscopy (SEM) results showed that fibers within the uncompressed gel were loose and irregularly ordered, whereas the fibers within the compressed gel were densely packed and more evenly arranged. Quantitative analysis of LECs expansion across the surface of the two gels showed similar growth rates (p > 0.05). Under SEM, the LECs, expanded on uncompressed gels, showed a rough and heterogeneous morphology, whereas on the compressed gel, the cells displayed a smooth and homogeneous morphology. Transmission electron microscopy (TEM) results showed the compressed scaffold to contain collagen fibers of regular diameter and similar orientation resembling collagen fibers within the normal cornea. TEM and light microscopy also showed that cell–cell and cell–matrix attachment, stratification, and cell density were superior in LECs expanded upon compressed collagen gels. This study demonstrated that the compressed collagen gel was an excellent biomaterial scaffold highly suited to the construction of an artificial corneal epithelium and a significant improvement upon conventional collagen gels.

Investigation of K14/K5 as a stem cell marker in the limbal region of the bovine cornea

Background: Identification of stem cells from a corneal epithelial cell population by specific molecular markers has been investigated previously. Expressions of P63, ABCG2 and K14/K5 have all been linked to mammalian corneal epithelial stem cells. Here we report on the limitations of K14/K5 as a limbal stem cell marker. Methodology/Principal Findings: K14/K5 expression was measured by immunohistochemistry, Western blotting and Real time PCR and compared between bovine epithelial cells in the limbus and central cornea. A functional study was also included to investigate changes in K5/14 expression within cultured limbal epithelial cells undergoing forced differentiation. K14 expression (or its partner K5) was detected in quiescent epithelial cells from both the limbal area and central cornea. K14 was localized predominantly to basal epithelial cells in the limbus and suprabasal epithelial cells in the central cornea. Western blotting revealed K14 expression in both limbus and central cornea (higher levels in the limbus). Similarly, quantitative real time PCR found K5, partner to K14, to be expressed in both the central cornea and limbus. Following forced differentiation in culture the limbal epithelial cells revealed an increase in K5/14 gene/protein expression levels in concert with a predictable rise in a known differentiation marker. Conclusions/Significance: K14 and its partner K5 are limited not only to the limbus but also to the central bovine cornea epithelial cells suggesting K14/K5 is not limbal specific in situ. Furthermore K14/K5 expression levels were not lowered (in fact they increased) within a limbal epithelial cell culture undergoing forced differentiation suggesting K14/K5 is an unreliable maker for undifferentiated cells ex vivo.

Ex vivo expansion of limbal stem cells is affected by substrate properties

Limbal epithelial stem cells play a key role in the maintenance and regulation of the corneal surface. Damage or destruction of these cells results in vascularisation and corneal opacity. Subsequent limbal stem cell transplantation requires an ex vivo expansion step and preserving cells in an undifferentiated state remains vital. In this report we seek to control the phenotype of limbal epithelial stem cells by the novel application of compressed collagen substrates. We have characterised the mechanical and surface properties of conventional collagen gels using shear rheology and scanning electron microscopy. In doing so, we provide evidence to show that compressive load can improve the stiffness of collagen substrates. In addition Western blotting and immunohistochemistry display increased cytokeratin 3 (CK3) protein expression relating to limbal epithelial cell differentiation on stiff collagen substrates. Such gels with an elastic modulus of 2900 Pa supported a significantly higher number of cells than less stiff collagen gels (3 Pa). These findings have substantial influence in the development of ocular surface constructs or experimental models particularly in the fields of stem cell research, tissue engineering and regenerative medicine.

The mechanical properties of amniotic membrane influence its effect as a biomaterial for ocular surface repair

The human amniotic membrane (AM) is a tissue of fetal origin and has proven to be clinically useful as a biomaterial in the management of various ocular surface disorders including corneal stem cell transplantation. However, its success rate displays a degree of clinical unpredictability. We suggest that the measured variability inAMstiffness offers an explanation for the poor clinical reproducibility when it is used as a substrate for stem cell expansion and transplantation. Corneal epithelial stem cells were expanded upon AM samples possessing different mechanical stiffness. To investigate further the importance of biological substrate stiffness on cell phenotype we replaced AM with type I collagen gels of known stiffness. Substrate stiffness was measured using shear rheometry and surface topography was characterized using scanning electron microscopy and atomic force microscopy. The differentiation status of epithelial cells was examined using RT-PCR, immunohistochemistry and Western blotting. The level of corneal stem cell differentiation was increased in cells expanded upon AM with a high dynamic elastic shear modulus and cell expansion on type I collagen gels confirmed that the level of corneal epithelial stem cell differentiation was related to the substrate’s mechanical properties. In this paper we provide evidence to show that the preparatory method of AM for clinical use can affect its mechanical properties and that these measured differences can influence the level of differentiation within expanded corneal epithelial stem cells.