Electrothermal AAS determination of Ni in soft drinks using Co as the internal standard

A method for the direct determination of Ni in soft drinks by graphite furnace atomic absorption spectrometry using a transversely heated graphite atomizer (THGA), Zeeman-effect background corrector, and Co as the internal standard (IS) is proposed. Magnesium nitrate was used to stabilize both Ni and Co. All diluted samples (1+1) in 0.2% (v/v) HNO3 and reference solutions [5.0-50 mu g L-1 Ni in 0.2% (v/v) HNO3] were spiked with 50 mu g L-1 Co. For a 20-mu L sample dispensed into the atomizer, correlations between the ratio of absorbance of Ni to absorbance of Co and the analyte concentration were close to 0.9996. The relative standard deviation of the measurements varied from 0.5 to 3.4% and 1.0 to 7.0% (n=12) with and without IS, respectively. Recoveries within 98-104% for Ni spikes were obtained using IS. The characteristic mass was calculated as 43 pg Ni and the limit of detection was 1.4 mu g L-1. The accuracy of the method was checked for the direct determination of Ni in soft drinks and the results obtained with IS were better than those without IS.

Synthesis, spectral and thermal studies on pyrazolate-bridged palladium(II) coordination polymers

Synthesis, spectroscopic characterization and thermal behavior of pyrazolate-bridged palladium complexes [Pd(mu-Pz)(2)](n) (1), [Pd(mu-mPz)(2)](n) (2), [Pd(mu-dmPz)(2)](n) (3), [Pd(mu-IPz)(2)](n) (4) {pyrazolate (Pz(-)), 4-methylpyrazolate (mPz(-)), 3,5-dimethylpyrazolate (dmPz(-)), 4-iodopyrazolate (IPz(-))} have been described in this work. The exobidentate coordination mode of pyrazolato ligands in 1-4 was inferred on basis of IR spectroscopic evidences. TG investigations indicated that the introduction of substituents at the 4 position in the pyrazolyl moiety into coordination polymers do not affect significantly their thermal stability, whereas at the 3 and 5 position reduced the stability of the main chain. Metal palladium was the final product of the thermal decompositions, which was identified by X-ray powder diffraction.

Comparative studies of the anti-leishmanial activity of three Crotalus durissus ssp venoms

In this study, we compared the anti-leishmanial activity of three crotalic venoms (Crotalus durissus terrificus-Cdt, Crotalus durissus cascavella-Cdca, and Crotalus durissus collilineatus-Cdcol). Different concentrations of each venom incubated with Leishmania (Leishmania) amazonensis promastigotes were used. Cdt venom exhibited a higher anti-leishmanial activity (Inhibitory concentration-IC50-value of 4.70 +/- 1.72 mu g/ml) in comparison with that of Cdca venom (IC50 value of 9.41 +/- 1.21 mu g/ml), while Cdcol venom increased parasite numbers in 50% at a concentration of 44.30 +/- 2.18 mu g/ml. In addition, this venom showed a low anti-leishmanial activity in higher concentrations (IC50 value of 281.00 +/- 9.50 mu g/ml). The main fractions of Cdca venom were isolated and assayed under similar conditions used for assessing crude venom. The most active fractions were gyroxin and crotamine that had IC50 values of 3.80 +/- 0.52 mu g/ml and 19.95 +/- 4.21 mu g/ml, respectively. Convulxin also inhibited parasite growth rate, although this effect was not dose-dependent. Crotoxin was the least effective fraction with an IC50 value of 99.80 +/- 2.21 mu g/ml. None of the protein fractions presented cytotoxic effects against J774 cells in culture. In vivo assays using BALB/c mice revealed that crotoxin and crotamine were the main toxic fractions. In conclusion, C. durissus cascavella venom has three main fractions with anti-leishmanial activity. These results open new possibilities to find proteins that might be used as possible agents against cutaneous leishmaniasis.

Use of sugar cane bagasse as solid phase extractor for cadmium determination by FAAS

The present paper describes the use of sugar cane bagasse as solid phase extractor for cadmium determination after complexation of the analyte with ammonium diethyldithiophosphate (ADDP) and sorption of the Cd-DDP complexes on the solid support. The concomitants were separated using a flow injection analysis (FIA) system coupled to flame atomic absorption spectrometry (FAAS) for determination. The main parameters such as ADDP concentration, acid medium, flow rate, reaction coil length, and reaction time were investigated.The results obtained with HNO3 showed good accuracy and precision. The enhancement factor was 20.5 times for a 120-second preconcentration time, and the analytical frequency was 25 determinations per hour. The calibration curve was linear over the concentration range of 1-40 mu g L-1 Cd with a LOD of 0.697 mu g L-1 Cd and a relative standard deviation of 0.96% after 12 successive measurements of 30 mu g L-1 Cd.The proposed method was evaluated for the FIA-FAAS analysis of certified reference materials (tomato leaves, spinach leaves, and bovine liver) and Cd-spiked foods (shrimp, sardine, tuna, chicken liver and bovine liver). Good recoveries (80.0-97.1%) for the Cd-spiked samples and certified reference materials were obtained. The results of bagasse-packed minicolumns were compared with Si-C,8 packed minicolumns. The F-test was applied between Si-C-18/Bagasse minicolumns, Si-C-18/certified values, and bagasse/certified values. It was found that the results were in agreement with the certified values at a 95% confidence level.

Cathodic stripping voltammetric determination of cefaclor in pharmaceutical formulations

A sensitive method is described for the determination of cefaclor by cathodic stripping voltammetry at the hanging mercury drop electrode. cefaclor is accumulated at the electrode surface as a mercury salt, which is reduced at -0.67 V. The optimum accumulation potential and accumulation time were +0.15 V and up to 180 s, respectively. Linear calibration graphs were obtained between 3.9 mu g.L-1 to 39 mu g.L-1 and the limit of determination was evaluated to be 1.9 mu g.L-1. The method was applied successfully to the determination of cefaclor in pharmaceutical formulations.

Effect of pancreas transplantation on the prevention of nephropathy in alloxan-induced diabetic rats

We studied the effects of pancreas transplantation on kidney lesions of rats with alloxan-induced diabetes. Ninety inbred male Lewis rats were randomly assigned to 3 experimental groups: group NC included 30 non-diabetic control rats, group DC included 30 alloxan-induced diabetic control rats, and group PT included 30 alloxan-induced diabetic rats that received pancreas transplants from normal donor Lewis rats. Each group was further divided into 3 subgroups of 10 rats which were sacrificed at 1, 3, and 6 months of follow-up, respectively. Clinical and laboratory parameters during these periods were documented. The kidneys of 5 rats in each subgroup were studied and 50 glomeruli and tubules from each kidney were analyzed by light microscopy by two different investigators in a double-blind study. There was progressive glomerular basement membrane thickening (GBMT), mesangial enlargement (ME), and Bowman's capsule thickening (BCT) in kidneys of rats in the 3 experimental groups during follow-up. These alterations were significantly higher in DC rats (GBMT: 1.99 +/- 0.31; ME: 2.00 +/- 0.33; BCT: 1.88 +/- 0.27) when compared to NC(GBMT: 1.54 +/- 0.30; ME: 1.56 +/- 0.47; BCT: 1.36 +/- 0.35) and PT rats (GBMT: 1.49 +/- 0.29; ME: 1.57 +/- 0.36; BCT: 1.35 +/- 0.28) at 6 months (P<0.01). The extent of GBMT, ME, and BCT observed in DC rats at 1 and 3 months was not significantly different from NC and PT rats. The amount of kidney lesions in PT rats was similar to that of NC rats and lower than those of DC rats at 6 months (P<0.01). In addition, Armanni-Ebstein lesions of the tubules (AE) and tubular lumen protein (PRO) observed in DC rats were not present in NC or PT rats. We conclude that pancreas transplantation in alloxan-induced diabetic rats prevents the development of kidney lesions beginning at 6 months after transplantation.

The validity of critical speed determined from track cycling for identification of the maximal lactate steady state

The objective of this study was to determine the critical speed (CS) for track cycling and to assess whether a lactate steady state occurs at this speed. Fourteen competitive cyclists performed the following tests on an official cycling track (333.3 m): 1) incremental test for determination of the intensity corresponding to 4 mM of blood lactate (onset of blood lactate accumulation, OBLA) and maximal oxygen uptake (VO(2)max); 2) CS: 3 maximal bouts for distances of 2, 4 and 6 km executed in random order and with a period of recovery of 40 to 50 min between bouts. CS was determined for each subject from the linear regression between the distance and the time taking to cycle it; 3) Endurance test in which subjects were instructed to pedal at 100% of their individually determined CS for 30 min. At the 10(th) and 30(th) min (or upon exhaustion), 25 mul of blood were collected from ear lobe for later analysis of blood lactate [Lac]b. An increase less than or equal to1 mM between 10 and 30 min of exercise was considered as the criterion for the occurrence of the lactate steady state. CS (49.6 +/- 8.6 ml.kg(-1).min(-1); 36.9 +/- 2.7 km.h(-1)) was significantly higher than OBLA (43.7 8.0 ml.kg(-1).min(-1); 35.24 +/- 2.6 km.h(-1)) although the two parameters were highly correlated (r=0.97). During the endurance test, only 8 of the 14 subjects completed the 30 min period at CS. of these 8 subjects, only 2 presented a lactate steady state. Time to exhaustion at CS was 20.3 +/- 1.6 min for the remaining 6 subjects. The 12 subjects who did not reach a lactate steady state presented mean [Lac]b values of 7.4 +/- 1.3 mM at 10 min and of 9.4 +/- 1.9 mM at the end of the test (exhaustion), characterizing an exercise intensity of high lactacidemia. on the basis of the present results, we can conclude that CS determined by a track cycling test seems to overestimate the intensity of the maximal lactate steady state for most subjects.

PARTICIPATION OF OPIOID RECEPTORS IN THE MODULATION OF THE ANALGESIC RESPONSE BY ADRENAL AND GONADAL GLANDS

The involvement of opioid receptors in the analgesic response was evaluated by the tail-immersion test in simultaneously adrenalectomized and ovariectomized female Wistar rats (210-250 g). The reaction time (mean +/- SEM) for tail withdrawal from hot water decreased significantly 2 weeks after surgery (3.52 +/- 0.20 s) when compared to intact animals (6.09 +/- 0.23 s). Hormonal replacement with dexamethasone (50-mu-g/day) did not affect reaction time (3.38 +/- 0.19 s). However, this response was restored by combined adrenal and gonadal steroid substitution (estradiol 5-mu-g/day and progesterone 1.5-mu-g 6 h before the tests) therapy (5.11 +/- 0.45 s in animals treated with dexamethasone plus estradiol and 5.04 +/- 0.43 s in animals treated with dexamethasone plus estradiol plus progesterone). Naloxone (2 mg/kg) decreased the reaction time of animals treated with adrenal and gonadal steroids (5.11 +/- 0.45 vs 4.15 +/- 0.44 s and 5.04 +/- 0.43 vs 3.87 +/- 0.28 s, respectively, before and after naloxone) but failed to decrease it in rats treated with dexamethasone only (3.88 +/- 0.18 vs 4.34 +/- 0.25 s, before and after naloxone). These observations indicate that gonadal steroids are the most important steroid factors involved in the reaction time to tail immersion in hot water and confirm other reports that the opioid pathways modulating the neuronal circuitry require the presence of these hormones.

The influence of crystallization route on the properties of lanthanum-doped Bi4Ti3O12 thin films prepared from polymeric precursors

Pure and lanthanum-doped Bi4Ti3O12 thin films were deposited on Pt/Ti/SiO2/Si substrate using a polymeric precursor solution. The spin-coated films were specular and crack-free and crystalline after annealing at 700 degreesC for 2 h. Crystallinity and morphological evaluation were examined by X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM). Multilayered films obtained using the intermediate-crystalline layer route present a dense microstructure with spherical grains. Films obtained using the intermediate-amorphous layer, present elongated grains around 250 nm in size. The dielectric and ferroelectric properties of the lanthanum-doped Bi4Ti3O12 films are strongly affected by the crystallization route. The hysteresis loops are fully saturated with a remnant polarization and drive voltage of the films, heat-treated by the intermediate-crystalline (P-r = 20.2 muC/cm(2) and V = 1.35 V) and for the film heat-treated by amorphous route (P-r = 22.4 muC/cm(2) and V = 2.99 V). (C) 2004 Elsevier B.V. All rights reserved.

In vitro evaluation of acidified toothpastes with low fluoride content

Fluoride toothpastes are a risk factor for the development of dental fluorosis. Products with low fluoride content offer a higher security, but their effectiveness must be proven. The aim of this in vitro study was to compare two acidified toothpastes with low fluoride concentration (412 and 550 mu g F/g) with neutral toothpastes. Bovine enamel blocks were selected by surface microhardness (SMH) and randomized to twelve groups of 13, according to the fluoride concentration in toothpaste (placebo, 275, 412, 550 or 1,100 jig F/g) and pH (7.0 or 5.5). Two commercially available toothpastes were also studied: a 1,100-mu g F/g, pH 7.0 paste (positive control) and a children's paste (500 mu g F/g, pH 7.0). The blocks were subjected to pH cycling for 7 days. The toothpaste treatment was done twice daily. Surface and cross-sectional microhardnesses were assessed to calculate the percentage change of SMH (%SMH) and the mineral loss (Delta Z). The amount of fluoride, calcium and phosphorus in the solutions after the pH cycling was also analyzed. Compared to neutral toothpastes, the acidified toothpastes reduced the %SMH in all F concentrations. Higher F and lower Ca and P concentrations were found in solutions for the acidified toothpastes. Regarding AZ, only the positive control, 1,100-mu g F/g (acidified and neutral) groups were not statistically different. The acidified toothpastes showed a dose-response relationship with all variables. For the low-fluoride toothpastes evaluated, only the 550-mu g F/g acidified paste had the same anticariogenic action as the 1,100-mu g F/g neutral paste.

Phagocytosis of PLGA microparticles in rat peritoneal exudate cells: A time-dependent study

With the purpose of enhancing the efficacy of microparticle-encapsulated therapeutic agents, in this study we evaluated the phagocytic ability of rat peritoneal exudate cells and the preferential location of poly(D,L-lactide-co-glycolic acid) (PLGA) microparticles inside these cells. The microparticles used were produced by a solvent evaporation method and were characterized by dynamic light scattering (DLS), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). Size distribution analysis using DLS and SEM showed that the particles were spherical, with diameters falling between 0.5 and 1.5 mu m. Results from cell adhesion by SEM assay, indicated that the PLGA microparticles are not toxic to cells and do not cause any distinct damage to them as confirmed by the MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide) assay. Among the large variety of cell populations found in the peritoneal exudates (neutrophils, eosinophils, monocytes, and macrophages), TEM showed that only the latter phagocytosed PLGA microparticles, in a time-dependent manner. The results obtained indicate that the microparticles studied show merits as possible carriers of drugs for intracellular delivery.

Quantitative analysis of mineral content in enamel using laboratory microtomography and microhardness analysis. - art. no. 631823

This study evaluates laboratory microtomography and microhardness analysis for quantifying the mineral content of bovine enamel. Fifty enamel blocks were submitted individually for 5 days to a pH-cycling model at 37 degrees C and remained in the remineralizing solution for 2 days. The blocks were treated twice daily for 1 min with NaF dentifrices (Placebo, 275, 550, 1,100 mu g F/g and Crest (R)) diluted in deionized water. Surface microhardness changes (%SMH) and mineral loss (Delta Z) were then calculated. Laboratory microtomography was also used to measure total mineral lost (LMM). Pearson's correlation (p < 0.05) was used to determine the relationship between different methods of analysis and dose-response between treatments. Dentifrice fluoride concentration and %SMH and Delta Z were correlated (p < 0.05). There was a positive relationship (p < 0.05) when comparing LMM vs. Delta Z; a negative relationship (p < 0.05) was found for %SMH vs. LMM and %SMH vs. Delta Z. Therefore, both mineral quantification techniques provide adequate precision for studying the bovine enamel-pH-cycling demineralization/remineralization model.

Biocompatibility of gutta-percha solvents using in vitro mammalian test-system

Objectives. Taking into consideration that DNA damage and cellular death play important roles during carcinogenesis, the purpose of the present study was to evaluate in vitro genotoxic or cytotoxic effects of chloroform and eucalyptol by single cell gel (comet) assay and trypan blue exclusion test, respectively.Study design. Chloroform and eucalyptol were exposed to Chinese hamster ovary cells in culture directly for 3 hours at 37 degrees C at final concentrations ranging from 1.25 to 10 mu L/mL. The negative control group was treated with vehicle control (phosphate-buffered solution), and the positive control group was treated with methyl metasulfonate (MMS, at 1 mu g/mL concentration). All data were analyzed by the Kruskal-Wallis nonparametric test followed by the Dunn test.Results. The results showed that both gutta-percha solvents were cytotoxic at concentrations of 2.5, 5, and 10 mu L/mL (P < .05). on the other hand, both solvents did not induce DNA breakage at 1.25 mu L/mL concentration.Conclusions. These results suggest that both chloroform or eucalyptol are strong cytotoxicants, but they may not be a factor that increases the level of DNA lesions in mammalian cells.

Determination of Cd(II) and Cd-metallothioneins in biological extracts using baker's yeast and inductively coupled plasma optical emission spectrometry

The use of Saccharomyces cerevisiae as a sorbent material to separate Cd(II) and Cd-metallothionein complex (Cd-MT) has been explored. Solid-liquid phase extractions were carried out in batch mode and the main parameters of the process (pH, temperature, time of incubation, amount of biomass and analyte) were evaluated. Under optimized conditions, the yeast quantitatively retain (94 +/- 5%) the Cd(II) while 97 +/- 2% of the Cd-MT remain in the supernatant. on base of the findings of this study, a simple method is proposed to determine Cd(II) and Cd-MT in cytosols extracted from mouse kidney and crab hepatopancreas. Inductively coupled plasma optical emission spectrometry was used to quantify the analytes in solid and liquid phase. Determination of Cd in the solid phase was carried out by introducing a slurry of the yeast (0.0625 g/10 mL) directly to the inductively coupled plasma optical emission spectrometer. Mixed standards solutions, which also have been submitted to the extraction procedure, were used to quantify the analytes in the samples. Thus, matrix effects due to nebulization of the slurry were overcame. Limits of detection (3 sigma) for Cd(II) and Cd-MT were 1.5 and 1.2 mu g L-1, respectively. Relative standard deviations of signals were 4.2% for measurements in the slurry of solid phase and 2.1% for measurements in the liquid phase. Recoveries of the analytes in cytosol samples were between 76 and 114%. The concentrations of Cd(II) (2.4 +/- 0.5 mu g L-1) and Cd-MT (3.0 +/- 0.5 mu g L-1) found by using the proposed approach were close to those found by tangential-flow ultrafiltration technique (2.6 +/- 0.7 mu g L-1 for Cd(II) and 3.7 +/- 1.7 mu g L-1 for Cd-MT).

Genetic and environmental effects over milk production of buffalo cows in Brazil

The objective of this paper was to evaluate the relevance of environmental and genetics effects on milk production of buffalo cows in Brazil. The data were based on the Buffalo Genetic Improvement Program - PROMEBUL, using information of 1,911 cows (107 Jafarabadi, 101 Mediterranean, 1,056 Mu/Tab and 647 crossbred females) with parturition between 1982 and 2003. The mathematic model for evaluating milk production included the fixed effects of herd, parturition year (1982 to 2003) and month (January to December), calf's sex (male or female), genetic group (Jafarabadi, Mediterranean, Murrah, and crossbreed), number of milking (one or two), lactation order (1 to 12) and duration of lactation (as a linear effect). The mean milk production in herds was 1,590.36 +/- 609.25 kg. All sources of variation were significant (P<0.05) for the studied characteristics, except calf's sex. The mean milk production per genetic group was 1,651.4; 1,592.2; 1,578.3 and 1,135.5 kg, for Murrah, Mediterranean, Crossbred and Jafarabadi, respectively. The duration of lactation was the most important source of variation over milk production, followed by the year of parturition, herd, parturition order, genetic group and month of parturition.