Control of Large-size SiC Growth Process Using Modeling tool

Large size bulk silicon carbide (SiC) crystals are commonly grown by the physical vapor transport (PVT) method. The PVT growth of SiC crystals involves sublimation and condensation, chemical reactions, stoichiometry, mass transport, induced thermal stress, as well as defect and micropipes generation and propagation. The quality and polytype of as-grown SiC crystals are related to the temperature distribution inside the growth chamber during the growth process, it is critical to predict the temperature distribution from the measured temperatures outside the crucible by pyrometers. A radio-frequency induction-heating furnace was used for the growth of large-size SiC crystals by the PVT method in the present study. Modeling and simulation have been used to develop the SiC growth process and to improve the SiC crystal quality. Parameters such as the temperature measured at the top of crucible, temperature measured at the bottom of the crucible, and inert gas pressure are used to control the SiC growth process. By measuring the temperatures at the top and bottom of the crucible, the temperatures inside the crucible were predicted with the help of modeling tool. SiC crystals of 6H polytype were obtained and characterized by the Raman scattering spectroscopy and SEM, and crystals of few millimeter size grown inside the crucible were found without micropipes. Expansion of the crystals were also performed with the help of modeling and simulation.

The A Posteriori Aspects of Estuarine Modeling

This exercise is the application of an analytical method for systematically modeling ecosystems data to observations made on a naturally eutrophic, mesohaline planktonic microcosm. The theory and experimental design are briefly outlined and the particular steps in the acutal modeling process follow. Then there is a discussion as to how the whole endeavor can be refined to culminate in models with predictive capabilities. (PDF has 16 pages.)

Modeling the Chesapeake Bay and Tributaries: a synopsis

The last decade has seen the development and application of a spectrum of physical and numerical hydrographic models of the Chesapeake Bay and its tributaries. The success of the James River Hydraulic Model has initiated the construction of an estuarine hydraulic model of the entire Chesapeake System. Numerical analogues for hydrographic behavior and contaminant dispersion in one-, two-, and three dimensional model estuaries exist for various regions of the Bay. From an engineering viewpoint, one dimensional models are sufficiently advanced to be routinely employed in aiding management decisions. Bay investigators are playing leading roles in the development of two- and three-dimensional models of estuarine flows.

Modeling of a Laminar DC Arc Plasma Torch

In recent years, stable and long laminarplasma jets have been successfully generated, and thus it is possible to achieve low-noise working surroundings, better process repeatability and controllability, and reduced metal-oxidation degree in plasma materials processing. With such a recent development in thermal plasma science and technology as the main research background, modeling studies are performed concerning the DCarcplasmatorch for generating the long laminar argon plasma jet. Two different two-dimensional modeling approaches are employed to deal with the arc-root attachment at the anode surface. The first approach is based on circumferentially uniform arc-root attachment, while the second uses the so-called fictitious anode method. Modeling results show that the highest temperature and maximum axial-velocity at the plasmatorch exit are ～15000 K and ～1100 m/s, respectively, for the case with arc current of 160 A and argon flow rate of 1.95×10{sup}(-4)kg/s.

The Empirical Modeling of an Ecosystem

The authors have endeavored to create a verified a-posteriori model of a planktonic ecosystem. Verification of an empirically derived set of first-order, quadratic differential equations proved elusive due to the sensitivity of the model system to changes in initial conditions. Efforts to verify a similarly derived set of linear differential equations were more encouraging, yielding reasonable behavior for half of the ten ecosystem compartments modeled. The well-behaved species models gave indications as to the rate-controlling processes in the ecosystem.

Physical Modeling of Current-Induced Seabed Scour around a Vibrating Submarine Pipeline

Most of the existing researches either focus on vortex-induced-vibrations (VIV) of a pipeline near a rigid boundary, or on seabed scour around a fixed pipeline. In the fields, pipeline vibration and seabed scour are actually always coupled. Based on the similarity analysis, a series of tests were conducted with a hydro-elastic facility to investigate the influence of pipe vibration on the local scour and the effects of scour process on the pipeline dynamic responses. Experimental results indicate that, there exist two phases in the process of sand scouring around the pipeline with small embedment, i.e. Phase I: scour beneath pipe without VIV, and Phase II: scour with VIV of pipe. It is also found that the gap-to-diameter ratio (e/D) has much effect upon the scour depth for the fixed pipes. For a given value of e/D, the vibrating pipes with close proximity to seabed may induce a deeper scour hole than the fixed ones. Within the examined gap-to-diameter ratio range (425 < e/D < 0.75), the influences of gap-to-diameter ratio on the maximum values of scour-depth for the case of vibrating pipes are not as much as those for the case of fixed pipes.

Modeling Environmental Stress

The word stress when applied to ecosystems is ambiguous. Stress may be low-level, with accompanying near-linear strain, or it may be of finite magnitude, with nonlinear response and possible disintegration of the system. Since there are practically no widely accepted definitions of ecosystem strain, classification of models of stressed systems is tenuous. Despite appearances, most ecosystem models seem to fall into the low-level linear response category. Although they sometimes simulate systems behavior well, they do not provide necessary and sufficient information about sudden structural changes nor structure after transition. Dynamic models of finiteamplitude response to stress are rare because of analytical difficulties. Some idea as to future transition states can be obtained by regarding the behavior of unperturbed functions under limiting strain conditions. Preliminary work shows that, since community variables do respond in a coherent manner to stress, macroscopic analyses of stressed ecosystems offer possible alternatives to compartmental models.

Modeling Study of Shrouding Gas Effects on a Laminar Argon Plasma Jet Impinging Upon a Flat Substrate in Air Surroundings

With the laminar plasma materials processing as the research background, modeling study is conducted concerning the effects of argon shroud on the characteristics of the laminar argon plasma jet impinging normally upon a flat substrate located in air surroundings. It is shown that adding shrouding gas is an effective method to reduce and control the entrainment of ambient air into the laminar plasma jet. The shrouding gas flow rate or velocity, the injection slot width and the stand-off distance of the substrate appreciably affect the air contents in the plasma near the substrate surface.

Modeling of Ammonothermal Growth of Gallium Nitride Single Crystals

Ammonothermal growth of GaN crystals with a retrograde solubility has been modeled and simulated here using fluid dynamics, thermodynamics and heat transfer models. The nutrient is considered as a porous media bed and the flow in the porous charge is simulated using the Darcy-Brinkman-Forchheimer model. The resulting governing equations are solved using the finite volume method. For the case of retrograde solubility, the charge is put above the baffle. The temperature difference between the dissolving zone and growth zone is found smaller than that applied on the sidewall of autoclave. The baffle opening has a strong effect on the nutrient transport and supersaturation of GaN species in the growth zone.

Growth of Silicon Carbide Bulk Crystals by Physical Vapor Transport Method and Modeling Efforts in the Process Optimization

Silicon carbide bulk crystals were grown in an induction-heating furnace using the physical vapor transport method. Crystal growth modeling was performed to obtain the required inert gas pressure and temperatures for sufficiently large growth rates. The SiC crystals were expanded by designing a growth chamber having a positive temperature gradient along the growth interface. The obtained 6H-SiC crystals were cut into wafers and characterized by Raman scattering spectroscopy and X-ray diffraction, and the results showed that most parts of the crystals had good crystallographic structures.

Monte Carlo Modeling of Micro Scale Gas Flows

An information preservation (IP) method has been used to simulate many micro scale gas flows. It may efficiently reduce the statistical scatter inherent in conventional particle approaches such as the direct simulation Monte Carlo (DSMC) method. This paper reviews applications of IP to some benchmark problems. Comparison of the IP results with those given by experiment, DSMC, and the linearized Boltzmann equation, as well as the Navier-Stokes equations with a slip boundary condition, and the lattice Boltzmann equation, shows that the IP method is applicable to micro scale gas flows over the entire flow regime from continuum to free molecular.