Forecasting inbound tourists in Cambodia

Forecasting tourism demand is crucial for management decisions in the tourism sector. Estimating a vector autoregressive (VAR) model for monthly visitor arrivals disaggregated by three entry points in Cambodia for the years 2006–2015, I forecast the number of arrivals for years 2016 and 2017. The results show that the VAR model fits well with the data on visitor arrivals for each entry point. Ex post forecasting shows that the forecasts closely match the observed data for visitor arrivals, thereby supporting the forecasting accuracy of the VAR model. Visitor arrivals to Siem Reap and Phnom Penh airports are forecast to increase steadily in future periods, with varying fluctuations across months and origin countries of foreign tourists.

Optimization of a label-free biosensor vertically characterized based on a periodic lattice of high aspect ratio SU-8 nano-pillars with a simplified 2D theoretical model

We have recently demonstrated a biosensor based on a lattice of SU8 pillars on a 1 μm SiO2/Si wafer by measuring vertically reflectivity as a function of wavelength. The biodetection has been proven with the combination of Bovine Serum Albumin (BSA) protein and its antibody (antiBSA). A BSA layer is attached to the pillars; the biorecognition of antiBSA involves a shift in the reflectivity curve, related with the concentration of antiBSA. A detection limit in the order of 2 ng/ml is achieved for a rhombic lattice of pillars with a lattice parameter (a) of 800 nm, a height (h) of 420 nm and a diameter(d) of 200 nm. These results correlate with calculations using 3D-finite difference time domain method. A 2D simplified model is proposed, consisting of a multilayer model where the pillars are turned into a 420 nm layer with an effective refractive index obtained by using Beam Propagation Method (BPM) algorithm. Results provided by this model are in good correlation with experimental data, reaching a reduction in time from one day to 15 minutes, giving a fast but accurate tool to optimize the design and maximizing sensitivity, and allows analyzing the influence of different variables (diameter, height and lattice parameter). Sensitivity is obtained for a variety of configurations, reaching a limit of detection under 1 ng/ml. Optimum design is not only chosen because of its sensitivity but also its feasibility, both from fabrication (limited by aspect ratio and proximity of the pillars) and fluidic point of view. (© 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim)

Enhanced iron gettering by short, optimized low-temperature annealing after phosphorus emitter diffusion for industrial silicon solar cell processing

The introduction of a low-temperature (LT) tail after P emitter diffusion was shown to lead to considerable improvements in electron lifetime and solar cell performance by different researchers. So far, the drawback of the investigated extended gettering treatments has been the lack of knowledge about optimum annealing times and temperatures and the important increase in processing time. In this manuscript, we calculate optimum annealing temperatures of Fe-contaminated Si wafers for different annealing durations. Subsequently, it is shown theoretically and experimentally that a relatively short LT tail of 15 min can lead to a significant reduction of interstitial Fe and an increase in electron lifetime. Finally, we calculate the potential improvement of solar cell efficiency when such a short-tail extended P diffusion gettering is included in an industrial fabrication process.

Si and SixGe1-x NWs studied by Raman spectroscopy

Group IV nanostructures have attracted a great deal of attention because of their potential applications in optoelectronics and nanodevices. Raman spectroscopy has been extensively used to characterize nanostructures since it provides non destructive information about their size, by the adequate modeling of the phonon confinement effect. The Raman spectrum is also sensitive to other factors, as stress and temperature, which can mix with the size effects borrowing the interpretation of the Raman spectrum. We present herein an analysis of the Raman spectra obtained for Si and SiGe nanowires; the influence of the excitation conditions and the heat dissipation media are discussed in order to optimize the experimental conditions for reliable spectra acquisition and interpretation.

Study of helical induced anisotropy in amorphous ribbons for sensor applications

Amorphous samples with helical induced anisotropy show magnetization processes that can be controlled by applying a longitudinal magnetic field simultaneously with an alternating current flowing through the sample. By varying the current amplitude and the phase difference between current and applied field, a wide range of coercivity and susceptibility values can be achieved. This work shows that the apparent coercive field and the susceptibility can be controlled in amorphous ribbons with helical anisotropy. These characteristics make these samples very suitable for their application as sensor cores, magnetic amplifiers, variable reluctance transformer cores, etc