A single-Stream jet noise prediction model for a family of chevron nozzles

This study develops a single-stream jet noise prediction model for a family of chevron nozzles. An original equation is proposed for the fourth-order space-time cross-correlations. They are expressed in flow parameters such as streamwise circulation and turbulent kinetic energy. The cross-correlations based on a Reynolds Averaged Navier-Stokes (RANS) flowfield showed a good agreement with those based on a Large Eddy Simulation (LES) flowfield. This proves that the proposed equation describes the cross-correlations accurately. With this novel source description, there is an excellent agreement between our model's far-field noise predictions and measurements1 for a wide range of frequencies and radiation angles. Our model captures the spectral shape, amplitude and peak frequency very well. This establishes that our model holds good for a family of chevron nozzles. As our model provides quick and accurate predictions, a parametric study was performed to understand the effects of a chevron nozzle geometry on jet noise and thrust loss. Chevron penetration is the underpinning factor for jet noise reduction. The reduction of jet noise per unit thrust loss decreases linearly with chevron penetration. The number of chevrons also has a considerable effect on jet noise.

Alternative cold response modes in Chlorella (Chlorophyta, Trebouxiophyceae) from Antarctica

Chlorella was known to show enhanced antifreeze capability after cold hardening. We isolated Chlorella strains NJ-7 and NJ-18, which display alternative cold response modes from rock surfaces in Antarctica. On the basis of 18S ribosomal (rRNA) sequences, NJ-7 is an Antarctic type of Chlorella vulgaris; NJ-18 is also a 'true' Chlorella species but differs from any previously reported species in structure. NJ-7 partially retained the enhancing effects of low temperature cultivation on freeze tolerance, which correlates with an increase of C18:3-fatty acid content and up-regulation of two antifreeze protein genes. NJ-18, however, showed stable freeze tolerance regardless of the precultivation temperature. We propose that cold response modes vary widely in Chlorella and that the adaptation of C. vulgaris to Antarctica may serve as a model system for the evolution of antifreeze mechanisms in a single species of photosynthetic microorganism.

Cloning of biologically active genomes from a Helicoverpa armigera single-nucleocapsid nucleopolyhedrovirus isolate by using a bacterial artificial chromosome

Purification of genotypes from baculovirus isolates provides understanding of the diversity of baculoviruses and may lead to the development of better pesticides. Here, we report the cloning of different genotypes from an isolate of Helicoverpa armigera single-nucleocapsid nucleopolyhedrovirus (HaSNPV) by using a bacterial artificial chromosome (BAC). A transfer vector (pHZB10) was constructed which contained an Escherichia coli mini-F replicon cassette within the upstream and downstream arms of HaSNPV polyhedrin gene. Hz2e5 cells were co-transfected with wild-type HaSNPV DNA and pHZB10 to generate recombinant viruses by homologous recombination. The DNA of budded viruses (BVs) was used to transform E. coli. One of the bacmid colonies, HaBacHZ8, has restriction enzyme digestion profiles similar to an in vivo cloned strain HaSNPV-G4, the genome of which has been completely sequenced. For testing the oral infectivity, the polyhedrin gene of HaSNPV was reintroduced into HaBacHZ8 to generate the recombinant bacmid HaBacDF6. The results of one-step growth curves, electron microscopic examination, protein expression analysis and bioassays indicated that HaBacDF6 replicated as well as HaSNPV-G4 in vitro and in vivo. The biologically functional HaSNPV bacmids obtained in this research will facilitate future studies on the function genomics and genetic modification of HaSNPV. (C) 2003 Elsevier B.V. All rights reserved.

The effect of single AlGaN interlayer on the structural properties of GaN epilayers grown on Si (111) substrates

High-quality and nearly crack-free GaN epitaxial layer was obtained by inserting a single AlGaN interlayer between GaN epilayer and high-temperature AlN buffer layer on Si (111) substrate by metalorganic chemical vapor deposition. This paper investigates the effect of AlGaN interlayer on the structural proper-ties of the resulting GaN epilayer. It confirms from the optical microscopy and Raman scattering spectroscopy that the AlGaN interlayer has a remarkable effect on introducing relative compressive strain to the top GaN layer and preventing the formation of cracks. X-ray diffraction and transmission electron microscopy analysis reveal that a significant reduction in both screw and edge threading dislocations is achieved in GaN epilayer by the insertion of AlGaN interlayer. The process of threading dislocation reduction in both AlGaN interlayer and GaN epilayer is demonstrated.

Field emission mechanism from a single-layer ultra-thin semiconductor film cathode

Field emission (FE) from a single-layer ultra-thin semiconductor film cathode (SUSC) on a metal substrate has been investigated theoretically. The self-consistent quantum FE model is developed by synthetically considering the energy band bending and electron scattering. As a typical example, we calculate the FE properties of ultra-thin A1N film with an adjustable film thickness from 1 to 10 nm. The calculated results show that the FE characteristic is evidently modulated by varying the film thickness, and there is an optimum thickness of about 3 nm. Furthermore, a four-step FE mechanism is suggested such that the distinct FE current of a SUSC is rooted in the thickness sensitivity of its quantum structure, and the optimum FE properties of the SUSC should be attributed to the change in the effective potential combined with the attenuation of electron scattering.

Growth of single crystalline ZnxCd1-xS nanocombs by metallo-organic chemical vapor deposition

Single crystalline ternary ZnxCd1-xS nanocombs, which have 'comb' shaped' teeth on one side, have been synthesized by a one-step metallo-organic chemical vapor deposition process at a low temperature of 420 degrees C. The asymmetric, growth behavior of the nanocombs is likely to be induced by the polarization of the c-ptane. Because of the uniform structure and perfect geometrical shape, the nanoteeth could be potentially useful as nanocantilever arrays for nanosensors and, nanotweezers. (c) 2006 Elsevier B.V. All rights reserved.

Structural optimizations of SOI-based single-mode rib waveguide bends

Effects of structure parameters on bend loss of rib silicon-on-insulator (Sol) bend waveguides have been analyzed by means of effective index method (EIM) and 2D bend loss formula. The simulation results indicate that the bend loss decreases with the increase of bend radius and waveguide width, as well as with the decrease of the step factor of the rib waveguide. Moreover, the optional structure parameters have been found when bend waveguides are single-mode.

Single-mode holey vertical-cavity surface-emitting laser with ultra-narrow beam divergence

We demonstrated oxide-confined 850-nm vertical-cavity surface-emitting lasers (VCSELs) with a two-dimensional petal-shaped holey structure composed of several annular-sector-shaped holes. Four types of devices with different hole numbers were designed and fabricated. The measured results showed that the larger hole number was beneficial to purifying the lasing mode, and realizing the single-mode operation. The side mode suppression ratio (SMSR) exceeded 30 dB throughout the entire drive current. Mode selective loss mechanism was used to explain the single-mode characteristic. The single-mode devices possessed good beam profiles, and the lowest divergence angle was as narrow as 3.2 degrees (full width at half maximum), attributed to the graded index profile and the shallow etching in the top distributed Bragg reflector (DBR).

Lapping technique of InP single crystal wafer

The wafer processing of Indium Phosphide (InP) is so important that it is getting more and more attentions. Lapping is a basic step just following the ingot cutting. In this paper, the influences of various processing parameters on the lapped wafer quality and lapping rate have been checked, the double-crystal X-ray diffraction results about lapped wafers also were presented here. According to the experimental results, the optimum lapping conditions have been obtained.

Photoluminescence studies of GaAs/AlGaAs single quantum well intermixed by Ga+ ion implantation

Ga(+)ion implantation followed by rapid thermal annealing (RTA) was used to enhance the interdiffusion in GaAs/AlGaAs single Quantum Wells(SQWs). The extent of intermixing was found to be dependent on the well depth, number of implanted ions and annealing time. A very fast interdiffusion process occurs at the initial annealing stage. After that, the enhanced diffusion coefficient goes back to the umimplanted value. We propose a two-step model to explain the diffusion process as a function of the annealing time : a fast diffusion process and a saturated diffusion process. The interdiffusion coefficient of the fast diffusion was found to be of well depth dependence and estimated to be in the range of 5.4x10(-16) similar to 1.5x10(-15)cm(2)s(-1). Copyright (C) 1996 Published by Elsevier Science Ltd

DIRECT OBSERVATION FOR THE REDUCTION OF EXCITON BINDING-ENERGY INDUCED BY PERPENDICULAR ELECTRIC-FIELD

We experimentally study the effect of perpendicular electric field on the exciton binding energy using a specially designed step quantum well. From photoluminescence spectra at the temperature of 77 K, we have directly observed remarkable blueshift of the exciton peak due to the transition from spatially direct to spatially indirect excitons induced by electric field. (C) 1995 American Institute of Physics.

Dislocation Reduction in GaN on Sapphire by Epitaxial Lateral Overgrowth

High quality GaN is grown on GaN substrate with stripe pattern by metalorganic chemical vapor deposition by means of epitaxial lateral overgrowth. AFM,wet chemical etching, and TEM experiments show that with a two-step ELOG procedure, the propagation of defects under the mask is blocked, and the coherently grown GaN above the window also experiences a drastic reduction in defect density. In addition, a grain boundary is formed at the coalescence boundary of neighboring growth fronts. The extremely low density of threading dislocations within wing regions makes ELOG GaN a potential template for the fabrication of nitride-based lasers with improved performance.

Single ridge waveguide electroabsorption modulated DFB laser for 2.5Gb/s transmission

In this paper we proposed a single ridge waveguide electroabsorption modulated distributed feedback laser (EML) for long-haul high-speed optical fiber communication system. This EML was successfully fabricated by two step metal organic vapor phase epitaxy (MOVPE) including selective area growth (SAG) and helium partially implantation. No obvious changes of the threshold current (< 0.2 mA), extinction ratio (< 0.1 dB), output power (< 0.2 dBm) and isolation resistance were achieved in the preliminary aging test. With 2.5 Gb/s NRZ modulation, no power penalty was observed after the optical signal was transmitted through 280 Km normal single mode fiber.

Diffractive microlens with a cascade focal plane fabricated by single mask UV-photolithography and common KOH:H2O etching

A diffractive microlens with a cascade focal plane along the main optical axis of the device is fabricated using a low-cost technique mainly including single mask ultraviolet (UV) photolithography and dual-step KOH:H2O etching. Based on the evolutionary behavior of converse pyramid-shaped microholes (CPSMs) preshaped over a {100}-oriented silicon wafer in KOH etchant, the first-step KOH etching is performed to transfer initial square micro-openings in a SiO2 film grown by plasma enhanced chemical vapor deposition (PECVD) and patterned by single mask UV-photolithography, into CPSMs with needed dimension. After completely removing a thinned SiO2 mask, basic annular phase steps with a relatively steep sidewall and scheduled height can be shaped in the overlapped etching region between the neighboring silicon concave-arc microstructures evolved from CPSMs through the second-step KOH etching. Morphological measurements demonstrate a desirable surface of the silicon microlens with a roughness in nanometer scale and the feature height of the phase steps formed in the submicrometer range. Conventional optics measurements of the plastic diffractive microlens obtained by further hot embossing the fine microrelief phase map over the nickel mask made through a common electrochemical method indicate a highly efficient cascaded focusing performance.

Splitting the Fast and Slow Motions in Molecular Dynamics Simulations Based on the Change of Cold Potential Well Bottom

The atomic motion is coupled by the fast and slow components due to the high frequency vibration of atoms and the low frequency deformation of atomic lattice, respectively. A two-step approximate method was presented to determine the atomic slow motion. The first step is based on the change of the location of the cold potential well bottom and the second step is based on the average of the appropriate slow velocities of the surrounding atoms. The simple tensions of one-dimensional atoms and two-dimensional atoms were performed with the full molecular dynamics simulations. The conjugate gradient method was employed to determine the corresponding location of cold potential well bottom. Results show that our two-step approximate method is appropriate to determine the atomic slow motion under the low strain rate loading. This splitting method may be helpful to develop more efficient molecular modeling methods and simulations pertinent to realistic loading conditions of materials.