Relato de Rhizoctonia solani AG-4 HG I em crisântemo (Papiro Branco e Amarelo) e R. solani AG-4 HG III em gipsófila no estado de São Paulo, Brasil, e sua patogenicidade cruzada

Atualmente, grupamento de anastomose (AG) de Rhizoctonia sp. em crisântemo e ocorrência deste fungo em gipsófila ainda não foram relatados no Brasil. Assim, realizou-se teste de patogenicidade normal e cruzada e sequenciamento da região ITS-5.8S rDNA para identificar o AG de isolado obtido de plantas de crisântemo (Papiro Branco) e de gipsófila, ambas originárias de Holambra / São Paulo, Brasil. Após os testes, relata-se pela primeira vez a ocorrência de R. solani AG-4 HG I em crisântemo (Papiro Branco e Amarelo) e R. solani AG-4 HG III em gipsófila, no estado de São Paulo, Brasil, e, também, a sua patogenicidade cruzada.

Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Native species indicated for degraded area recovery in Western Paraná, Brazil

Colonization in the State of Paraná has culminated in the devastation of large forest areas in the entire State. Degraded area recovery programs have emphasized the utilization of native species, but often the species indicated for local reforestation areas are unknown, as those areas are little known floristically. This study aimed to survey native species indicated for reforestation of areas in the Western region of the State of Paraná, classify those species as pioneer, secondary, or climactic, and indicate places of occurrence of matrices where seeds of those species could be collected. Bibliographic surveys in the specialized literature and research in the Herbarium Museu Botânico Municipal de Curitiba (MBM) and Herbarium of Universidade Estadual do Oeste do Paraná (UNOP) were conducted to identify potential species for degraded area recovery in the study of Western region of Paraná. In all, 115 species were selected, of which 22 are pioneer, 73 are secondary, and 20 are climactic. The bibliographic surveys suggests that pioneer species are the most indicated for the initial processes in the degraded areas recovery, while secondary and climactic species play a major role in area enrichment.

Investment recovery period in electric motor of higher efficiency in pumping for irrigation

In this study, it was adjusted a mathematical model to measure the effect of electric motor efficiency on pumping system costs for irrigation on the tariff structure of conventional electricity and green horo-seasonal , and also to calculate the recovery period of the invested capital in higher efficiency equipment. Then, it was applied to a center pivot irrigation system in two options of electric motor efficiency, 92,6% (standard line) and 94,3% (high efficiency line), and the acquisition cost of the first corresponded to 70% the of the second. The power of the electric motor was 100hp. The results showed that the model allowed us to evaluate if a high efficiency motor was economically viable compared to the standard motor in each tariff structure. The high efficiency motor was not viable in the two tariff structures. In the green horo-seasonal tariff, would only be viable if its efficiency was 4.46% higher than the standard motor. In the conventional tariff, it would only be viable if the efficiency overcame 2.71%.

Pretreatment processes in gold recovery by thiosulphate leaching

This thesis describes several different pretreatment processes for gold concentrates and ores. The thesis is divided to theoretical part and experimental part. The theoretical part presents the operating principle of the main pretreatment methods and their suitability for thiosulphate leaching. In the theoretical part also the whole recovery process for gold from ore to elemental gold is presented. In the experimental part the study is focused on pretreatment of sulphidic refractory concentrates with mechanical activation and chemical oxidation under alkaline environment; and their effect on leachability in the thiosulphate leaching. In the experimental part a combined 2-step process, where chemical oxidation under ammoniacal environment is cascaded with thiosulphate leaching in the same conditions, is also tested. The main sulphuric mineral components in the studied refractory concentrate are pyrite (49.4 %) and arsenopyrite (27.7 %). The gold content in the concentrate is 11.3 ppm and silver content is 90 ppm. Without pretreatment the gold conversion in thiosulphate leaching was 30 %, which was analyzed at the time point of 9 hours. At that time the silver conversion was 17 %. By using mechanical activation the gold conversion reached was 59 % and silver conversion 26 %. With chemical oxidation under alkaline environment, where the used chemical was sodium hydroxide, the reached conversion of gold was 72 % and 31 % for silver. In the combined oxidation and leaching experiment the conversion of gold remained at 49 % and 18 % for silver.

Recovery of carboxylic acids from aqueous streams by extraction and back extraction

Separation of carboxylic acids from aqueous streams is an important part of their manufacturing process. The aqueous solutions are usually dilute containing less than 10 % acids. Separation by distillation is difficult as the boiling points of acids are only marginally higher than that of water. Because of this distillation is not only difficult but also expensive due to the evaporation of large amounts of water. Carboxylic acids have traditionally been precipitated as calcium salts. The yields of these processes are usually relatively low and the chemical costs high. Especially the decomposition of calcium salts with sulfuric acid produces large amounts of calcium sulfate sludge. Solvent extraction has been studied as an alternative method for recovery of carboxylic acids. Solvent extraction is based on mixing of two immiscible liquids and the transfer of the wanted components form one liquid to another due to equilibrium difference. In the case of carboxylic acids, the acids are transferred from aqueous phase to organic solvent due to physical and chemical interactions. The acids and the extractant form complexes which are soluble in the organic phase. The extraction efficiency is affected by many factors, for instance initial acid concentration, type and concentration of the extractant, pH, temperature and extraction time. In this paper, the effects of initial acid concentration, type of extractant and temperature on extraction efficiency were studied. As carboxylic acids are usually the products of the processes, they are wanted to be recovered. Hence the acids have to be removed from the organic phase after the extraction. The removal of acids from the organic phase also regenerates the extractant which can be then recycled in the process. The regeneration of the extractant was studied by back-extracting i.e. stripping the acids form the organic solution into diluent sodium hydroxide solution. In the solvent regeneration, the regenerability of different extractants and the effect of initial acid concentration and temperature were studied.

Recovery of Mollicutes from the reproductive tract of dairy cattle in the state of Pernambuco, Brazil

Abstract: The aim of the present study was to report the occurrence of members of the Mollicutesclass in the reproductive system of dairy cattle in Brazil. Five farms containing dairy cattle were visited in January of 2012. In total, 100 cows of different ages, breeds and stages of lactation were examined in the present study. The cows were part of intensive or semi-intensive management systems and were submitted to mechanical milking or hand milking. The samples were collected after washing the vulvar region with water and soap, and then drying it with paper towels and disinfecting the area with alcohol (70°GL). Vaginal mucous was collected using a sterile alginate cotton swab, which was rubbed on the vagina, as well as the lateral and internal walls. Vulvovaginal mucous samples were cultured in both liquid and solid modified Hayflick´s medium, for mycoplasmas, and UB medium, for ureaplasmas. The PCR assays for Mollicutesand Ureaplasmaspp. were performed according to the standard protocols described in the current literature. During isolation, the frequency of Mycoplasmaspp. was of 13.0% (13/100) and for Ureaplasmaspp. was of 6.0% (6/100). In the PCR assays the frequency of Mollicuteswas of 26.0% (26/100) and for Ureaplasmaspp. was of 13.0% (13/100) in the dairy cattle studied. This is the first report of these agents in reproductive system of bovine of the Pernambuco state. Further studies are necessary to determine the pathogenic potential and species of these field isolates.

Evaluation of cardiopulmonary parameters and recovery from anesthesia in cougars (Puma concolor) anesthetized with detomidine/ketamine and isoflurane or sevoflurane

Abstract: The aim of this study was to assess the cardiopulmonary effects, the onset time after the administration of a detomidine/ketamine combination, and the recovery from anesthesia of cougars (Puma concolor) anesthetized with detomidine/ketamine and isoflurane or sevoflurane for abdominal ultrasound imaging. Fourteen animals were randomly allocated into two experimental groups: GISO (n=7) and GSEVO (n=7). Chemical restraint was performed using 0.15mg/kg detomidine combined with 5mg/kg ketamine intramuscularly; anesthesia induction was achieved using 2mg/kg propofol intravenously and maintenance with isoflurane (GISO) or sevoflurane (GSEVO). The following parameters were assessed: heart rate, respiratory rate, systolic and diastolic arterial blood pressure, mean arterial blood pressure, oxyhemoglobin saturation, rectal temperature, central venous pressure, and end-tidal carbon dioxide. The time to sternal recumbency (TSR) and time to standing position (TSP) were also determined. There was not statistically significant difference for the cardiopulmonary variables or TSP whereas TSR was significantly shorter in GSEVO. The time to onset of anesthesia was 11.1±1.2 minutes and 11.3±1.8 minutes for GISO and GSEVO, respectively. The anesthesia of cougars with detomidine/ketamine and isoflurane or sevoflurane was conducted with safety, cardiopulmonary stability, and increased time to sternal recumbency in the GISO group.

NH90-helikopterin soveltuvuus Personnel Recovery –operaation suorittamiseen

Tutkielmassa tarkastellaan Puolustusvoimien käyttämän NH90-kuljetushelikopterin soveltuvuutta Personnel Recovery -operaation CSAR-menetelmän kuljetusalustaksi. Tutkimuksen tarkoituksena on selvittää, kuinka hyvin NH90-helikopteri vastaa Naton asettamiin vaatimuksiin taistelukentän etsintä- ja pelastustoimintaa suorittavalle kulje-tushelikopterille vertaamalla NH90-helikopterin laitteiden ja järjestelmien tuottamaa suorituskykyä Naton vaatimuksiin. Kyseessä on laadullinen tutkimus, jonka tutkimusstrategiana on käytetty tapaustutki-musta. Tutkielman lähdeaineiston rungon muodostavat kirjalliset lähteet, joita on tut-kittu käyttämällä aineistolähtöistä sisällönanalyysia. Tutkimuksen johtopäätökset on saatu vertailemalla eri alalukujen tuloksia keskenään. Lähdeaineistoista merkittävim-piä ovat Naton Personnel Recovery -toimintaa käsittelevät doktriinit sekä NH90-helikopteria ja sen ominaisuuksia käsittelevät valmistajan sekä Helikopteripataljoonan julkaisemat tekstit. Tärkeiden ominaisuuksien kohdalla tietoa on pyritty keräämään useammasta paikasta, ja näin parantamaan tutkielman luotettavuutta. Tutkimus osoittaa, että NH90-helikopteri soveltuu sodan ja kriisinaikaiseen etsintä- ja pelastustoimintaan hyvin. NH90-helikopterin suunnittelussa on pyritty ottamaan kat-tavasti huomioon nykyaikaisen sodankäynnin kuljetushelikoptereita vastaan asettamat uhkakuvat, jonka vuoksi se vastaa Naton asettamiin vaatimuksiin erinomaisesti. On kuitenkin huomioitava, että kyseessä on hyvin tuore helikopterityyppi, jonka todelli-nen käytännön testi karuissa olosuhteissa on vielä näkemättä. Tästä huolimatta voi-daan todeta, että NH90 on suunniteltu uhka-alueella toimivaksi monipuoliseksi ja muuntautumiskykyiseksi kuljetushelikopteriksi, jolla voidaan toteuttaa haastavia ope-raatioita vaikeissakin olosuhteissa. Vaikka tutkimus on hyvin teoreettinen, voidaan sen tuloksia pitää realistisina. Tutki-mus toimii hyvänä perustana etsintä- ja pelastustoimintaan liittyvissä asioissa, mutta aiheen laajuuden vuoksi jatkotutkimusta tarvitaan, jotta aiheeseen voidaan paneutua syvällisemmin, ja asiasta voidaan tehdä merkittäviä johtopäätöksiä.

Wastewater Treatment and Deinking Sludge Utilization Possibilities for Energy and Material Recovery in the Leningrad Region

Operation of pulp and paper mills generates waste including wastewater treatment sludge and deinking sludge. Both sludge types are generated in large amounts and are mainly disposed of in landfills in the Leningrad Region resulting in environmental degradation. The thesis was aimed at seeking new sustainable ways of sludge utilization. Two paper mills operating in the Leningrad Region and landfilling their sludge were identified: “SCA Hygiene Products Russia” and “Knauf”. The former generates 150 t/day of deinking sludge, the latter – 145 t/day of secondary sludge. Chemical analyses of deinking sludge were performed to assess applicability of sludge in construction materials production processes. Higher heating value on dry basis of both sludge types was determined to evaluate energy potential of sludge generated in the Leningrad Region. Total energy output from sludge incineration was calculated. Deinking sludge could be utilized in the production process of “LSR-Cement” or “Slantsy Cement Plant Cesla” factories, and “Pobeda” and “Nikolsky” brick mills without exceeding current sludge management costs.