An Electromechanical Coupled Model of the Probe of a Scanning Fiber Imaging System

Thesis (Master's)--University of Washington, 2016-06

Transverse-Plane Ankle Rotation for Lower-Limb Amputees Using Two Novel Prostheses

Thesis (Ph.D.)--University of Washington, 2016-06

Magnetic Devices and Techniques for the Study of Viscoelasticity of Biomaterials and Myocardial Forces

Thesis (Ph.D.)--University of Washington, 2016-06

Development of Cookstove Emissions and Performance Testing Suite with Time-resolved Particulate Matter Analysis and Excess Air Estimation

Thesis (Master's)--University of Washington, 2016-06

Mode Localization in a Nearly Cyclic Symmetric System

Thesis (Ph.D.)--University of Washington, 2016-06

Output-Boundary Regulation Using Event-Based Feedforward for Nonminimum-Phase Systems

Thesis (Ph.D.)--University of Washington, 2016-06

Improving the Manufacturability of Active Microfluidic Devices using Stereolithography (SL)

Thesis (Master's)--University of Washington, 2016-06

The effect of resin type on the sintering of freeformed maraging steel

The role of the resin type on the sintering of maraging steel with boron additions has been investigated. Two different resins were added to the steel mixture and their subsequent debinding was evaluated and sintering responses compared with that of a resin-free alloy. The two resins used, nylon and a mixture of phenolic resin and synthetic wax, possessed different debinding behaviour, with the latter causing significant carbon contamination of the parts. This caused the formation of a Ti-Mo carbide, depleting the matrix of these elements. Consequently, the microstructure consisted of the equilibrium Fe-Fe2B eutectic, as well as a Mo-rich boride. The liquid phase also appeared to contain significant amounts of carbon, which lowered the temperature at which the liquid formed, resulting in high density occurring at a much lower temperature. When nylon was used as the binder, a similar sintering response to the resin-free alloy was observed. (C) 2002 Published by Elsevier Science B.V.

On the sintering of uncompacted, pre-alloyed Al powder alloys

The effect of the addition of elemental Mg, Sri and Pb on the sintering of impressed prealloyed 2124 and 6061 powder has been investigated. Despite being sintered at a temperature that resulted in similar to20 vol.% liquid phase, high density was possible only upon the addition of similar to1% elemental Mg as well as trace amounts of Sri or Pb. Additions of Mg facilitated oxide disruption, while Sri and Pb segregated to the liquid phase, where they reduced the liquid's surface tension, thus improving sintering. (C) 2002 Elsevier Science B.V. All rights reserved.

Optimal reliability improvement for used items sold with warranty

The market for used products is becoming more competitive and dealers of used products use warranty to promote sales as well as to provide assurnace to customers. Offering warranty results in additional costs associated with warranty servicing. This cost can be reduced through actions such as overhaul and upgrade that improves the reliability of the item. This is worthwhile only if the cost of improvement is less than the reduction in the warranty servicing cost. This paper deals with two models to decide on the reliability improvement strategies for used items sold with FRW policy.

Product warranty logistics: Issues and challenges

Warranty is an important element of marketing new products. The servicing of warranty results in additional costs to the manufacturer. Warranty logistics deals with various issues relating to the servicing of warranty. Proper management of warranty logistics is needed not only to reduce the warranty servicing cost but also to ensure customer satisfaction as customer dissatisfaction has a negative impact on sales and revenue. Unfortunately, warranty logistics has received very little attention. The paper links the literature on warranty and on logistics and then discusses the different issues in warranty logistics. It highlights the challenges and identifies some research topics of potential interest to operational researchers. (C) 2003 Elsevier B.V. All rights reserved.

Warranty and discrete preventive maintenance

Preventive maintenance actions over the warranty period have an impact on the warranty servicing cost to the manufacturer and the cost to the buyer of fixing failures over the life of the product after the warranty expires. However, preventive maintenance costs money and is worthwhile only when these costs exceed the reduction in other costs. The paper deals with a model to determine when preventive maintenance actions (which rejuvenate the unit) carried out at discrete time instants over the warranty period are worthwhile. The cost of preventive maintenance is borne by the buyer. (C) 2003 Elsevier Ltd. All rights reserved.

Warranty servicing strategies to improve customer satisfaction

Customer satisfaction with a purchased product depends on its performance under warranty and during the remainder of its useful life. Dissatisfaction with an item is important to a manufacturer since it can lead to the loss of potential customers through the negative word-of-mouth effect as well as existing customers switching to a competitor. In this paper, we define satisfaction in terms of the likelihood of a customer not switching to a different manufacturer when a new item needs to be purchased. Manufacturers can use specific servicing strategies to reduce warranty costs and this topic has already been addressed in the literature without considering the effect of customer dissatisfaction. In this paper, we propose particular strategies that will increase customer satisfaction and we discuss methods for obtaining the optimal parameters of these strategies.

Electrodeposition of composite copper/liquid-containing microcapsule coatings

This paper presents results on the preparation of microcapsules containing liquid organosilica, and their co-deposition with copper in an acidic copper electrolyte onto a carbon steel cathode to form a copper/microcapsule composite coating. Microscopic analyses of the surface and the cross-section of the coating confirm the incorporation of the liquid-containing microcapsules in the coating layer. The influence of microcapsules in the electrolyte on the cathode polarization, as well as that of process conditions on the microcapsule inclusion, is also discussed. (C) 2004 Kluwer Academic Publishers.