A linearly tunable low-voltage CMOS transconductor with improved common-mode stability and its application to (gm)-C filters

A linearly tunable low-voltage CMOS transconductor featuring a new adaptative-bias mechanism that considerably improves the stability of the processed-signal common,mode voltage over the tuning range, critical for very-low voltage applications, is introduced. It embeds a feedback loop that holds input devices on triode region while boosting the output resistance. Analysis of the integrator frequency response gives an insight into the location of secondary poles and zeros as function of design parameters. A third-order low-pass Cauer filter employing the proposed transconductor was designed and integrated on a 0.8-mum n-well CMOS standard process. For a 1.8-V supply, filter characterization revealed f(p) = 0.93 MHz, f(s) = 1.82 MHz, A(min) = 44.08, dB, and A(max) = 0.64 dB at nominal tuning. Mined by a de voltage V-TUNE, the filter bandwidth was linearly adjusted at a rate of 11.48 kHz/mV over nearly one frequency decade. A maximum 13-mV deviation on the common-mode voltage at the filter output was measured over the interval 25 mV less than or equal to V-TUNE less than or equal to 200 mV. For V-out = 300 mV(pp) and V-TUNE = 100 mV, THD was -55.4 dB. Noise spectral density was 0.84 muV/Hz(1/2) @1 kHz and S/N = 41 dB @ V-out = 300 mV(pp) and 1-MHz bandwidth. Idle power consumption was 1.73 mW @V-TUNE = 100 mV. A tradeoff between dynamic range, bandwidth, power consumption, and chip area has then been achieved.

The Use of Etoricoxib and Celecoxib for Pain Prevention After Periodontal Surgery: A Double-Masked, Parallel-Group, Placebo-Controlled, Randomized Clinical Trial

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Simultaneous solidification of two catalyst wastes and their effect on the early stages of cement hydration

Two catalyst wastes (RNi and RAI) from polyol production were considered as hazardous, due to their respective high concentration of nickel and aluminum contents. This article presents the study, done to avoid environmental impacts, of the simultaneous solidification/stabilization of both catalyst wastes with type II Portland cement (CP) by non-conventional differential thermal analysis (NCDTA). This technique allows one to monitor the initial stages of cement hydration to evaluate the accelerating and/or retarding effects on the process due to the presence of the wastes and to identify the steps where the changes occur. Pastes with water/cement ratio equal to 0.5 were prepared, into which different amounts of each waste were added. NCDTA has the same basic principle of Differential Thermal Analysis (DTA), but differs in the fact that there is no external heating or cooling system as in the case of DTA. The thermal effects of the cement paste hydration with and without waste presence were evaluated from the energy released during the process in real time by acquiring the temperature data of the sample and reference using thermistors with 0.03 A degrees C resolution, coupled to an analog-digital interface. In the early stages of cement hydration retarding and accelerating effects occur, respectively due to RNi and RAl presence, with significant thermal effects. During the simultaneous use of the two waste catalysts for their stabilization process by solidification in cement, there is a synergic resulting effect, which allows better hydration operating conditions than when each waste is solidified separately. Thermogravimetric (TG) and derivative thermogravimetric analysis (DTG) of 4 and 24 h pastes allow a quantitative information about the main cement hydrated phases and confirm the same accelerating or retarding effects due to the presence of wastes indicated from respective NCDTA curves.

Interaction between nitroheterocyclic compounds with beta-cyclodextrins: Phase solubility and HPLC studies

Chagas disease is a serious health problem for Latin America. Nitrofurazone (NF) and Hidroxymethylnitrofurazone (NFOH) are active against Trypanosoma cruzi. The effect of beta-cyclodextrin (beta-CD) and dimethyl-beta-cyclodextrin (DM-beta-CD) complexation on the UV absorption and retention time of nitrofurazone (NF) and its hydroxymethylated analog (NFOH) were studied in solution. The retention behavior was analyzed on a reversed phase C(18) column and the mobile phase used was acetonitrile-water (20/80 v/v), in which cyclodextrins (beta-CD or DM-beta-CD) were incorporated as a mobile phase additive. The decrease in the retention times of NF (or NFOH) with increasing concentration of HP-beta-CD enables the cleternnination of the complex stability constants by HPLC. A phase-solubility Study was performed. according to the method reported by Higuchi and Connors, to evaluate the changes of NF/NFOH in the complexation state, and the diagrams obtained suggested that it forms complexes with a stoichiometry of 1 : 1. This is an important Study for the characterization of potential formulations to be used as therapeutic options for the treatment of Chagas disease. (c) 2008 Elsevier B.V. All rights reserved.

Patients' Expectations of and Satisfaction with Implant-Supported Fixed Partial Dentures and Single Crowns

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of intraperitoneal or incisional bupivacaine on pain and the analgesic requirement after ovariohysterectomy in dogs

Objective To compare the effect of intraperitoneal (IP) or incisional (INC) bupivacaine on pain and the analgesic requirement after ovariohysterectomy in dogs.Study design Prospective, randomized clinical study.Animals Thirty female dogs undergoing ovariohysterectomy (OHE).Methods Dogs admitted for elective OHE were anesthetized with acepromazine, butorphanol, thiopental and halothane. Animals were randomly assigned to one of three groups (n = 10 per group). The treatments consisted of preincisional infiltration with saline solution (NaCl 0.9%) or bupivacaine with epinephrine and/or IP administration of the same solutions, as follows: INC and IP 0.9% NaCl (control group); INC 0.9% NaCl and IP bupivacaine (5 mg kg(-1), IP group); INC bupivacaine (1 mg kg(-1)) and IP 0.9% NaCl (INC group). Postoperative pain was evaluated by a blinded observer for 24 hours after extubation by means of a visual analog scale (VAS) and a numeric rating scale (NRS). Rescue analgesia (morphine, 0.5 mg kg(-1), IM) was administered if the VAS was > 5/10 or the NRS > 10/29.Results At 1 hour after anesthesia, VAS pain scores were [medians (interquartile range)]: 6.4 (3.1-7.9), 0.3 (0.0-2.6) and 0.0 (0.0-7.0) in control, IP and INC groups, respectively. VAS pain scores were lower in the IP compared to the control group. Over the first 24 hours, rescue analgesia was administered to 7/10, 5/10 and 3/10 dogs of the control, INC and IP groups, respectively. Total number of dogs given rescue analgesia over the first 24 hours did not differ significantly among groups.Conclusions and clinical relevance Intraperitoneal bupivacaine resulted in lower pain scores during the first hour of the postoperative period and there was a trend towards a decreased need for rescue analgesia after OHE in dogs.

Liposomal encapsulation improves the duration of soft tissue anesthesia but does not induce pulpal anesthesia

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

On optimizing micropower MOS regulated cascode circuits on switched current techniques

Trade-off between settling time and micropower consumption in MOS regulated cascode current sources as building parts in high-accuracy, current-switching D/A converters is analyzed. The regulation-loop frequency characteristic is obtained and difficulties to impose a dominant-pole condition to the resulting 2nd-order system are discussed. Raising pole frequencies while meeting consumption requirements is basically limited by parasitic capacitances. An alternative is found by imposing a twin-pole system in which design constraints are somewhat relaxed and settling slightly faster. Relationships between pole frequencies, transistor geometry and bias are established. Simulated waveforms obtained with PSpice of designed circuits following a voltage perturbation suggest a good agreement with theory. The proposed approach applied to the design of a micropower current-mode D/A converter improves its simulated settling performance.

Chiral asymmetry and gravitation theory

In this letter we apply an alternative approach, recently developed, to the description of massless particles of arbitrary spin to the case of spin-two particles. This provides a non-geometrical approach to the theory of linearized gravitation. Within this method the chiral components of a spinor field are treated as independent field variables. The free field Lagrangian is built up from the requirement of chiral invariance. This formulation is parallel to the neutrino theory and leads to a formulation that generalizes, to particles of spin-two, the two-component neutrino theory. At the free field level the analog of curvature tensor, spin connection tensor, and metric tensor are independent quantities. By introducing left-right asymmetric linear interactions of these chiral components we get the linearized gravitation theory.

Associacao de opioides lipofilicos a bupivacaina na anestesia peridural. Ha vantagem no aumento da dose do opioide?

Background and Objectives: - The effects of associating lipophilic opioids to local anesthetics in epidural anesthesia are not well defined. There are still questions and controversies about opioid doses to be used and their major effects in the epidural block. This study aimed at evaluating the epidural block effects in humans of the association of different fentanyl and sufentanil doses to bupivacaine with 1:200.000 epinephrine. Methods: - A double-blind randomized study was performed in 94 patients of both genders, physical status ASA I, aged between 18 and 60 years, submitted to lower abdomen, perineal or lower limb surgery. Patients without preanesthetic medication were epidurally injected with 100 mg (20 ml) 0.5% bupivacaine, 0.1 mg (0.1 ml) 1%o epinephrine plus a combination of the following drugs: BUPI Group (15 patients): 2 ml of 0.9% saline solution (SS); FENT50 Group (19 patients): 50 μg (1 ml) fentanyl + 1 ml SS; FENT100 Group (20 patients): 100 μg (2 ml) fentanyl; SUF30 Group (20 patients): 30 μg (0.6 ml) sufentanil + SS (1.4 ml); SUF100 Group (20 patients): 50 μg (1 ml) sufentanil + SS (1 ml). The following parameters were studied: onset of sensory block, analgesic block (onset time) in T12, T10 and T8, analgesic block duration in T10 and T12, motor block degree, consciousness degree, need for supplemental perioperative sedation and analgesia, hypotension, bradycardia and peri and post operative side-effects, analgesia duration, proportion of patients needing supplemental analgesia and evaluation of postoperative pain (pain analog visual scale). Results: Groups were demographically uniform. The addition of fentanyl or sufentanil did not alter major characteristics of perioperative epidural block and has not significantly increased postoperative analgesia duration as compared to the use of bupivacaine only. However, the addition of lipophilic opioids has increased the quality of perioperative anesthetic block, translated into a lesser need for supplemental analgesia (p < 0.02). The increased dose of fentanyl and especially of sufentanil has increased the incidence of perioperative drowsiness (p < 0.001) without significant increase in other side effects. Conclusions: In the conditions and doses used, the addition of lipophilic opioids to bupivacaine and the increased dose of lipophilic opioids have improved anesthetic block quality without changes in the epidural block characteristics or a significant increase in side effects, with the exception of drowsiness mainly caused by sufentanil. However, they were not able to provide a significant increase in postoperative analgesia duration.

Noise reduction in speech signals using a TMS320C31 digital signal processor

This paper describes a speech enhancement system (SES) based on a TMS320C31 digital signal processor (DSP) for real-time application. The SES algorithm is based on a modified spectral subtraction method and a new speech activity detector (SAD) is used. The system presents a medium computational load and a sampling rate up to 18 kHz can be used. The goal is load and a sampling rate up to 18 kHz can be used. The goal is to use it to reduce noise in an analog telephone line.

A low-voltage triode-MOSFET four-quadrant multiplier with optimized current-efficiency

A low-voltage, low-power four-quadrant analog multiplier with optimized current-efficiency is presented. Its core corresponds to a pseudodifferential cascode, gain-boosting triode-transconductor. According to a low-voltage 1.2μm CMOS n-well process, operand differential-amplitudes are 1.0Vpp and 0.32Vpp for a 1.3V-supply. Common-mode voltages are properly chosen to maximize current-efficiency to 58%. Total quiescent dissipation is 260μW. A range of PSPICE simulation supports theoretical analysis. Excellent linearity is observed on dc characteristic. Assuming a ±0.5% mismatch on (W/L) and VTH THD at full-scale is 0.93% and 1.42%, for output frequencies of 1MHz and 10MHz, respectively.

Soliton spectrum of integrable models with local symmetries

The soliton spectrum (massive and massless) of a family of integrable models with local U(1) and U(1) ⊗U(1) symmetries is studied. These models represent relevant integrable deformations of SL(2,ℝ) ⊗U(1) n-1-WZW and SL(2,ℝ) ⊗ SL(2,ℝ) ⊗U(1) n-2-WZW models. Their massless solitons appear as specific topological solutions of the U(1)(or U(1) ⊗ U(1)-) CFTs. The nonconformal analog of the GKO-coset formula is derived and used in the construction of the composite massive solitons of the ungauged integrable models. © SISSA/ISAS 2002.

Nonnegative trigonometric polynomials

An extremal problem for the coefficients of sine polynomials, which are nonnegative in [0,π] , posed and discussed by Rogosinski and Szego is under consideration. An analog of the Fejér-Riesz representation of nonnegative general trigonometric and cosine polynomials is proved for nonnegative sine polynomials. Various extremal sine polynomials for the problem of Rogosinski and Szego are obtained explicitly. Associated cosine polynomials k n (θ) are constructed in such a way that { k n (θ) } are summability kernels. Thus, the L p , pointwise and almost everywhere convergence of the corresponding convolutions, is established. © 2002 Springer-Verlag New York Inc.

In-process thermal damage detection in grinding with monitoring via Internet

This work aims the development of a dedicated system for detection of burning in surface grinding process, where the process will constantly be monitored through the acoustic emission and electric power of the induction motor drive. Acquired by an analog-digital converter, algorithms process the signals and a control signal is generated to inform the operator or interrupt the process in case of burning occurrence. Moreover, the system makes possible the process monitoring via Internet. Additionally, a comparative study between parameters DPO and FKS is carried through. In the experimental work one type of. steel (ABNT-1020 annealed) and one type of grinding wheel referred to as TARGA, model ART 3TG80.3 NVHB, were employed.