Cloud statistics and cloud radiative effect for a low-mountain site

In 2007, the Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF) was operated for a nine-month period in the Murg Valley, Black Forest, Germany, in support of the Convective and Orographically-induced Precipitation Study (COPS). The synergy of AMF and COPS partner instrumentation was exploited to derive a set of high-quality thermodynamic and cloud property profiles with 30 s resolution. In total, clouds were present 72% of the time, with multi-layer mixed phase (28.4%) and single-layer water clouds (11.3%) occurring most frequently. A comparison with the Cloudnet sites Chilbolton and Lindenberg for the same time period revealed that the Murg Valley exhibits lower liquid water paths (LWPs; median = 37.5 g m−2) compared to the two sites located in flat terrain. In order to evaluate the derived thermodynamic and cloud property profiles, a radiative closure study was performed with independent surface radiation measurements. In clear sky, average differences between calculated and observed surface fluxes are less than 2% and 4% for the short wave and long wave part, respectively. In cloudy situations, differences between simulated and observed fluxes, particularly in the short wave part, are much larger, but most of these can be related to broken cloud situations. The daytime cloud radiative effect (CRE), i.e. the difference of cloudy and clear-sky net fluxes, has been analysed for the whole nine-month period. For overcast, single-layer water clouds, sensitivity studies revealed that the CRE uncertainty is likewise determined by uncertainties in liquid water content and effective radius. For low LWP clouds, CRE uncertainty is dominated by LWP uncertainty; therefore refined retrievals, such as using infrared and/or higher microwave frequencies, are needed.

Global retrieval of ATSR cloud parameters and evaluation (GRAPE): dataset assessment

The Along-Track Scanning Radiometers (ATSRs) provide a long time-series of measurements suitable for the retrieval of cloud properties. This work evaluates the freely-available Global Retrieval of ATSR Cloud Parameters and Evaluation (GRAPE) dataset (version 3) created from the ATSR-2 (1995�2003) and Advanced ATSR (AATSR; 2002 onwards) records. Users are recommended to consider only retrievals flagged as high-quality, where there is a good consistency between the measurements and the retrieved state (corresponding to about 60% of converged retrievals over sea, and more than 80% over land). Cloud properties are found to be generally free of any significant spurious trends relating to satellite zenith angle. Estimates of the random error on retrieved cloud properties are suggested to be generally appropriate for optically-thick clouds, and up to a factor of two too small for optically-thin cases. The correspondence between ATSR-2 and AATSR cloud properties is high, but a relative calibration difference between the sensors of order 5�10% at 660 nm and 870 nm limits the potential of the current version of the dataset for trend analysis. As ATSR-2 is thought to have the better absolute calibration, the discussion focusses on this portion of the record. Cloud-top heights from GRAPE compare well to ground-based data at four sites, particularly for shallow clouds. Clouds forming in boundary-layer inversions are typically around 1 km too high in GRAPE due to poorly-resolved inversions in the modelled temperature profiles used. Global cloud fields are compared to satellite products derived from the Moderate Resolution Imaging Spectroradiometer (MODIS), Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) measurements, and a climatology of liquid water content derived from satellite microwave radiometers. In all cases the main reasons for differences are linked to differing sensitivity to, and treatment of, multi-layer cloud systems. The correlation coefficient between GRAPE and the two MODIS products considered is generally high (greater than 0.7 for most cloud properties), except for liquid and ice cloud effective radius, which also show biases between the datasets. For liquid clouds, part of the difference is linked to choice of wavelengths used in the retrieval. Total cloud cover is slightly lower in GRAPE (0.64) than the CALIOP dataset (0.66). GRAPE underestimates liquid cloud water path relative to microwave radiometers by up to 100 g m�2 near the Equator and overestimates by around 50 g m�2 in the storm tracks. Finally, potential future improvements to the algorithm are outlined.

Understanding the early stages of the innovation diffusion process: awareness, influence and communication networks

The themes of awareness and influence within the innovation diffusion process are addressed. The innovation diffusion process is typically represented as stages, yet awareness and influence are somewhat under-represented in the literature. Awareness and influence are situated within the contextual setting of individual actors but also within the broader institutional forces. Understanding how actors become aware of an innovation and then how their opinion is influenced is important for creating a more innovation-active UK construction sector. Social network analysis is proposed as one technique for mapping how awareness and influence occur and what they look like as a network. Empirical data are gathered using two modes of enquiry. This is done through a pilot study consisting of chartered professionals and then through a case study organization as it attempted to diffuse an innovation. The analysis demonstrates significant variations across actors’ awareness and influence networks. It is argued that social network analysis can complement other research methods in order to present a richer picture of how actors become aware of innovations and where they draw their influences regarding adopting innovations. In summarizing the findings, a framework for understanding awareness and influence associated with innovation within the UK construction sector is presented. Finally, with the UK construction sector continually being encouraged to be innovative, understanding and managing an actor’s awareness and influence network will be beneficial. The overarching conclusion thus describes the need not only to build research capacity in this area but also to push the boundaries related to the research methods employed.

Prêt-à-Médiatiser by House of POLLYFIBRE

Prêt-à-Médiatiser by House of POLLYFIBRE is a performance/film that takes the fashion show catwalk as a site for exploration, with a focus on the dialogue between liveness and mediatisation. The performance showcases a clothing collection that has been designed to be documented and thus is challenged in the context of the live event. Motivated by the 2-dimensionality and biased perspective of mediated images such as magazine photography, social network profiles images and the surfaces of digital interfaces, the garments are one sided and obstruct the models in their attempt to play out familiar fashion poses, unless they align themselves 'correctly' for the lense. There is material metaphor and wordplay throughout, for example the clothing pieces are made from interfacing fabrics that are physically cut, pasted and layered to create the rigid flat silhouettes. The performance is accompanied by live sound created by tools of the fashion industry (including scissors and camera clicks) that have been adapted and amplified to be used as instruments. The audience and press are invited to document the live event and the subsequent film is made using footage collated from the crew, the audience and the official press

Chitosan coated alginate beads for the survival of microencapsulated Lactobacillus plantarum in pomegranate juice

This work studied the effect of multi-layer coating of alginate beads on the survival of encapsulated Lactobacillus plantarum in simulated gastric solution and during storage in pomegranate juice at 4 °C. Uncoated, single and double chitosan coated beads were examined. The survival of the cells in simulated gastric solution (pH 1.5) was improved in the case of the chitosan coated beads by 0.5–2 logs compared to the uncoated beads. The cell concentration in pomegranate juice after six weeks of storage was higher than 5.5 log CFU/mL for single and double coated beads, whereas for free cells and uncoated beads the cells died after 4 weeks of storage. In simulated gastric solution, the size of the beads decreased and their hardness increased with time; however, the opposite trend was observed for pomegranate juice, indicating that there is no correlation between cell survival and the hardness of the beads.

RedGloo: Experiences of developing and using an emerging technology in higher education

Student life has change a lot since 2005 when the idea to create a Social Network Service (SNS) for students in the School of Systems Engineering at the University of Reading was conceived and went live in 2006, called RedGloo.

Clusters, connectivity and catch-up: Bollywood and Bangalore in the Global Economy

In this article, we make two important contributions to the literature on clusters. First, we provide a broader theory of cluster connectivity that has hitherto focused on organization-based pipelines and MNE subsidiaries, by including linkages in the form of personal relationships. Second, we use the lens of social network theory to derive a number of testable propositions. We propose that global linkages with decentralized network structures have the highest potential for local spillovers. In the emerging economy context, our theory implies that clusters linked to the global economy by decentralized pipelines have potential for in-depth catch-up, focused in industry and technology scope. In contrast, clusters linked through decentralized personal relationships have potential for in-breadth catch-up over a range of related industries and technologies. We illustrate our theoretical propositions by contrasting two emerging economy case studies: Bollywood, the Indian filmed entertainment cluster in Mumbai and the Indian software cluster in Bangalore.

The integrated WRF/urban modelling system: development, evaluation, and applications to urban environmental problems

To bridge the gaps between traditional mesoscale modelling and microscale modelling, the National Center for Atmospheric Research, in collaboration with other agencies and research groups, has developed an integrated urban modelling system coupled to the weather research and forecasting (WRF) model as a community tool to address urban environmental issues. The core of this WRF/urban modelling system consists of the following: (1) three methods with different degrees of freedom to parameterize urban surface processes, ranging from a simple bulk parameterization to a sophisticated multi-layer urban canopy model with an indoor–outdoor exchange sub-model that directly interacts with the atmospheric boundary layer, (2) coupling to fine-scale computational fluid dynamic Reynolds-averaged Navier–Stokes and Large-Eddy simulation models for transport and dispersion (T&D) applications, (3) procedures to incorporate high-resolution urban land use, building morphology, and anthropogenic heating data using the National Urban Database and Access Portal Tool (NUDAPT), and (4) an urbanized high-resolution land data assimilation system. This paper provides an overview of this modelling system; addresses the daunting challenges of initializing the coupled WRF/urban model and of specifying the potentially vast number of parameters required to execute the WRF/urban model; explores the model sensitivity to these urban parameters; and evaluates the ability of WRF/urban to capture urban heat islands, complex boundary-layer structures aloft, and urban plume T&D for several major metropolitan regions. Recent applications of this modelling system illustrate its promising utility, as a regional climate-modelling tool, to investigate impacts of future urbanization on regional meteorological conditions and on air quality under future climate change scenarios. Copyright © 2010 Royal Meteorological Society

Drivers of in-group and out-of-group electronic word-of-mouth (eWOM)

Purpose – The purpose of this study is to address a recent call for additional research on electronic word-of-mouth (eWOM). In response to this call, this study draws on the social network paradigm and the uses and gratification theory (UGT) to propose and empirically test a conceptual framework of key drivers of two types of eWOM, namely in-group and out-of-group. Design/methodology/approach – The proposed model, which examines the impact of usage motivations on eWOM in-group and eWOM out-of-group, is tested in a sample of 302 internet users in Portugal. Findings – Results from the survey show that the different drivers (i.e. mood-enhancement, escapism, experiential learning and social interaction) vary in terms of their impact on the two different types of eWOM. Surprisingly, while results show a positive relationship between experiential learning and eWOM out-of-group, no relationship is found between experiential learning and eWOM in-group. Research limitations/implications – This is the first study investigating the drivers of both eWOM in-group and eWOM out-of-group. Additional research in this area will contribute to the development of a general theory of eWOM. Practical implications – By understanding the drivers of different eWOM types, this study provides guidance to marketing managers on how to allocate resources more efficiently in order to achieve the company's strategic objectives. Originality/value – No published study has investigated the determinants of these two types of eWOM. This is the first study offering empirical considerations of how the various drivers differentially impact eWOM in-group and eWOM out-of-group.

Drivers of in‐group and out‐of‐group electronic word‐of‐mouth (eWOM)

Purpose– The purpose of this study is to address a recent call for additional research on electronic word‐of‐mouth (eWOM). In response to this call, this study draws on the social network paradigm and the uses and gratification theory (UGT) to propose and empirically test a conceptual framework of key drivers of two types of eWOM, namely in‐group and out‐of‐group. Design/methodology/approach– The proposed model, which examines the impact of usage motivations on eWOM in‐group and eWOM out‐of‐group, is tested in a sample of 302 internet users in Portugal. Findings– Results from the survey show that the different drivers (i.e. mood‐enhancement, escapism, experiential learning and social interaction) vary in terms of their impact on the two different types of eWOM. Surprisingly, while results show a positive relationship between experiential learning and eWOM out‐of‐group, no relationship is found between experiential learning and eWOM in‐group. Research limitations/implications– This is the first study investigating the drivers of both eWOM in‐group and eWOM out‐of‐group. Additional research in this area will contribute to the development of a general theory of eWOM. Practical implications– By understanding the drivers of different eWOM types, this study provides guidance to marketing managers on how to allocate resources more efficiently in order to achieve the company's strategic objectives. Originality/value– No published study has investigated the determinants of these two types of eWOM. This is the first study offering empirical considerations of how the various drivers differentially impact eWOM in‐group and eWOM out‐of‐group.

The multiple team formation problem using sociometry

The Team Formation problem (TFP) has become a well-known problem in the OR literature over the last few years. In this problem, the allocation of multiple individuals that match a required set of skills as a group must be chosen to maximise one or several social positive attributes. Speci�cally, the aim of the current research is two-fold. First, two new dimensions of the TFP are added by considering multiple projects and fractions of people's dedication. This new problem is named the Multiple Team Formation Problem (MTFP). Second, an optimization model consisting in a quadratic objective function, linear constraints and integer variables is proposed for the problem. The optimization model is solved by three algorithms: a Constraint Programming approach provided by a commercial solver, a Local Search heuristic and a Variable Neighbourhood Search metaheuristic. These three algorithms constitute the first attempt to solve the MTFP, being a variable neighbourhood local search metaheuristic the most effi�cient in almost all cases. Applications of this problem commonly appear in real-life situations, particularly with the current and ongoing development of social network analysis. Therefore, this work opens multiple paths for future research.

Elaboration and optimization of (Y,Er)Al(3)(BO(3))(4) glassy planar waveguides through the sol-gel process

In this work, a sol-gel route was used to prepare Y(0.9)Er(0.1)Al(3)(BO(3))(4) glassy thin films by spin-coating technique looking for the preparation and optimization of planar waveguides for integrated optics. The films were deposited on silica and silicon substrates using stable sols synthesized by the sol-gel process. Deposits with thicknesses ranging between 520 and 720 nm were prepared by a multi-layer process involving heat treatments at different temperatures from glass transition to the film crystallization and using heating rates of 2 degrees C/min. The structural characterization of the layers was performed by using grazing incidence X-ray diffraction and Raman spectroscopy as a function of the heat treatment. Microstructural evolution in terms of annealing temperatures was followed by high resolution scanning electron microscopy and atomic force microscopy. Optical transmission spectra were used to determine the refractive index and the film thicknesses through the envelope method. The optical and guiding properties of the films were studied by m-line spectroscopy. The best films were monomode with 620 nm thickness and a refractive index around 1.664 at 980 nm wavelength. They showed good waveguiding properties with high light-coupling efficiency and low propagation loss at 632.8 and 1550 nm of about 0.88 dB/cm. (C) 2009 Elsevier B.V. All rights reserved.

Countability and star covering properties

Whenever P is a topological property, we say that a topological space is star P if whenever U is an open cover of X, there is a subspace A subset of X with property P such that X = St(A, U). We study the relationships of star P properties for P is an element of {Lindelof, sigma-compact, countable} with other Lindelof type properties. (C) 2010 Elsevier B.V. All rights reserved.

Icke-följsamhet vid diabetes mellitus : en litteraturstudie

Syftet med föreliggande studie var att beskriva vad personer med diabetes anser inverka på deras möjlighet och vilja att följa egenvårdsråd (patientperspektivet) och att beskriva omvård-nad som stöder följsamhet (sjukvårdsperspektivet). Studien har genomförts som en litteratur-studie. Det visade sig att alla krav för att hålla sjukdomen under kontroll innebär livsstilsför-ändringar, som kan vara så utmanande för patienten, att han kanske inte kan eller vill vidta dessa. Bristande kunskap om sjukdomen och om dess egenvårdskrav kan göra honom dåligt emotionellt anpassad till denna, det vill säga han har inte accepterat att han har sjukdomen och han vill inte låta dess egenvårdskrav inkräkta på det sociala livet. Detta ger honom för-sämrade möjligheter att hantera sjukdomen på ett bra sätt. Barriärer av olika slag kan uppstå mellan patient och vårdgivare. Det kan röra sig om en upplevd brist på information och stöd när diabetes diagnosticerats eller en känsla av att vara utsatt för läkarens eller sjuksköterskans stereotypa föreställningar och/eller att bli paternalistiskt behandlad. Till barriärer räknas även klinisk misskötsel, det vill säga att läkare/sjuksköterska inte följer vedertagna riktlinjer för be-handling.Vad som kan inverka positivt på följsamheten är patientens stöd av anhöriga eller andra i det sociala nätverket. Omvårdnad som stöder följsamhet visade sig varapatientundervisning, främst om den inriktades på att öka patientens självständighet genom att låta undervisningen pågå under en längre tid, så att patienten hinner integrera sin nya kunskap med det dagliga livet. Med eller utan patientundervisning tar det tid att bygga upp ett socialt stöd och ett förtroende mellan patient och vårdare.

La risa en los Chistes de Facebook

People tell jokes in order to amuse and produce laughter. It is possible to represent laughter in the cyberspace discourse by writing how it sounds or by using a representation of a facial expression formed by various combinations of keyboard characters called emoticon. Jokes are appreciated by both men and women in our society but is there any difference between the way they represent laughter in the cyberspace discourse? In this research, we use the qualitative and quantitative method. First, we analyze the mechanism of linguistic construction of five jokes and their types and techniques based on Freud’s theory about this subject. Then we present the reactions produced by the jokes found in a social network and focus in the written representation of the laughter. The results show us that more women than men react to the jokes by writing a comment. The most popular laughter used by both men and women in a Spanish social network is "jajajaja" and the emoticon "XD". We have also found that people use the international laughter "hahahaha" and more women than men use "jejeje" to represent laughter in the same network. Although each individual has a laughter style, the way people represent the laughter graphically in the cyberspace discourse is almost the same between men and women but it differs in the way they use them as a reaction to the type and technique of the joke.