碱法草浆造纸蒸煮黑液厌氧生物降解性及其主要微生物类群研究

造纸行业是造成我国水环境有机污染物的重要污染源之一，其水污染的特点是小厂多、草浆多、工艺落后、污染扩散面广、造成废 水排放量大，每年排放的废水量约39亿立方米，占全国工业废水排放量的1/6，其中有机污染物（以BOD5计）160万吨左右，约占全 国工业废水中有机污染物总量的1/4。尤以占全国制浆造纸行业90%以上的碱法草浆造纸厂的蒸煮黑液量大面广，除含有机物外，还 含有木质素、残碱、硫化物、氯化物等污染物，属于PH值高、色度深、难于治理的高浓度有机废水，对水体污染特别严重，各地要 求治理呼声很高，急待研究并尽快找出各种有效的治理途径。对于碱法草浆蒸煮，黑液高浓度废水的治理，有各种方法，根据国内 的研究进展和我们已有试验工作表明，最经济有效，具有实用价值，在生产上可获得成功是厌氧处理法。近10多年来，国外关于高 效厌氧处理技术研究进展迅速，并出现了多种多样的工艺设备，如高效厌氧生物反应器，并在实用化方面取得了很大成绩，建立了 生产性装置，达到了高负荷运行，效果良好。本试验是根据我们已有研究基础，针对我国国情，对小型制浆造纸厂水污染防治除了 开发碱回收及各种综合利用技术外，要特别加强废水(废液)实用技术研究的指导思想，本试验采用改进型的上流式厌氧污泥床反应 器，设计了两种试验方案，通过试验结果如下。1. 试验方案I—碱法草浆黑液酸化和厌氧发酵I号UASB反应器动态模型试验结果表 明：(1). 采用中温35℃±1℃高效厌氧反应器USAB内装有填料(陶粒)和三相分离器，具有保持高浓度生物量和防止污泥流失的特点 ，污泥浓度Vs 可达30%以上，因而具有高效、节能、产能、滞留期短的优点，当进水CODcr在7500-10000mg/l，HRT由7天缩短到3天 ，有机容积负荷在1.22gCODcr/l·d-3.43gCODcr/l·d时，CODcr平均去除率可达55%-45.5%，最高CODcr去除率可达60.2-63.5%， BOD5去除率可达75.9-83.2%,沼气容积产气率可达0.29-0.67l/l·d，每克CODcr转化为沼气产率达0.39-0.48l/gCODcr·d，CH4含量 65.8-75.5%。厌氧发酵出水再用化学法进行后处理脱除难降解的木质素，CODcr总去除率达80%以上。(2). 动态试验结果表明：采 用酸化—厌氧发酵处理黑液工艺合理，技术路线可行。2. 试验方案II—黑液用化学法(Hcl)去除木质素进行厌氧发酵，II号UASB反 应器动态模型试验结果表明：(1). 采用中温35℃±1℃高效厌氧反应器UASB(内有软填料)，当进水CODcr7000-13000mg/l左右，HRT 由6天缩短到1天，有机负荷由0.98gCODcr/l·d增加到11gCODcr/l·d时，COD平均去除率均可稳定在70-77%，BOD5去除率为87.3- 93.1%，沼气容积产气率0.21-2.6l/l·d，每克CODcr转化为沼气产率为0.39-0.48l/gCODcr·d，高的可达0.53l/gCODcr·d，转化 率较高，CH4含量63-70%。(2). 试验证明碱法草浆黑液物化预处理—厌氧发酵处理的技术路线也是可行的，工艺合理、效果较好。 在有条件的工厂可采用。3.厌氧发酵阶段几大类群微生物计数表明：(1). 当发酵工艺和运行处于相对稳定状态时，微生物群体的 组成也达到相对的稳定，各类微生物之间保持动态平衡关系。当产乙酸菌的数量为107-108个/ml时，产甲烷菌的数量为105-106 个/ml，当产乙酸菌数量为106-107个/ml时，产甲烷菌的数量为103-105个/ml。(2).稳态运行条件下，黑液预处理为甲烷发酵创造 了有利的生态环境，获得了较好的处理效果和较高的COD转化为沼气的产率0.39-0.48l/g·CODcr·d，反应器中形成较为稳定而数 量较下水污泥中高1-2个数量级的厌氧发酵微生物区系组成。这一结果为黑液厌氧发酵提供了微生物理论依据。Paper industry is one of the important pollution source of water environment in our country. Its character of water pollution is many small factories, much grass pulp, disadvantageous technique, large preading area of pullution. Its effluent makes up 1/6 of whole country's industry wastwater. Its organic pollutant accounts 1/4 of whole country's. Alkaline grass paper pulp effluent with pollutants such as ligoin, remaining alkali sulfide, chloride besides organic material, is a kind of high concentrate organic wastewater which has high PH walug, dark colour and is difficult in treatment. There is urgent require to find ways to treat the wastewater. There are different ways to treat alkaline paper grass pulp effluent. According to the research advances and our experiment work, the most economical and useful way is anaerobic degradation which was advanced quick in last ten years. In the control of waste water of small pulp paper mill, the study of wastewater utilization technology should be emphasized, besides alkaline retrieving and different kinds of comprehensive utilization technology. Our experiment used modified UASB(Upflow Anaerobic Sludge Blanket Reactor). Two kinds of plan were disgned. The results are lined below. 1. The first experiment plant-aciding black pulp effluent and methanogenic digestion. The dynamic model experiment results of I-UASB reactor showed: (1)The mesophilic(35℃±1℃)high effect UASB reactor having haydite and threee state seperation in it had the character of keeping high bioimass concentration and preventing losss of sludge. It had advantages of high effect, energe saving, energe prodcing and short HRT(Hydroulic retention time). When the influent COD was 7500-10000mg, HRT was shortened from 7 days to 3days, organic loading rate was 1.22g-3.43COD/l· d, the average COD removal efficiency was 55%-45%. The highest COD efficiency was 60.2-63.5%, BOD removal of 75.9 -83.4% was achieved. Biogass production rate were up to 0.29-0.67l/l·d. Biogass converted efficiency from every gram of COD could reach 0.39-0.48l/gCOD·d. Methane content was 65.0-75.5%. Chemical method was used to deplate lignin in anaerobic digestion effluent. Total COD removal efficiency could be more than 80%. (2)Using aciding annaerobic digestion to treat the black effluent was reseanable in technique and technology. 2. The second experiment plan-anaerobic digestion was used after the chemical method was used to deplate lignin in the black effluent. The result of dynamic experiment of II-UASB reactor showed: (1)High effect mesophilic (35℃±1℃)UASB reactor having soft slaffing in was used. When influent COD was about 7000-13000mg/l, HRT was shortened from 6 days to 1 day and organic loading rate was increased from 0.90 to 11g COD /l·d, average COD removal efficiency remained stable on 70-77%. BOD, removal efficiency was between 87.3-93.1%. Biogass production rate was 0.2-2.6l/l ·d .Biogass converted efficiency from a gram of COD was 0.39-0.481/gCOD·d with the high value of 0.53l/gCOD·d. Methane content was 63-70%. (2)The way that using physical, chemical Pre-treatment-anaerobic digestion to treat alkaline black effluent is feasible and can be used in some factories when the condition exists. 3. Counting of several class of microoganisms in anaerobic digestion stage showed: (1)As the disgestion was in stable motion, the compositon of microorganic colony could get relative stable. Dynamic balance was remaining among different kinds of microorganism such as methanogenic bacteria, Acidogenic bacteria, sulfate reducing bacteria, and heterotrophic bacteria. (2)Under stable motion, the pre-treatment of black effluent produced favourable eco-enviroment for methanegenic digestion. Good treatment effect and high biogass convertent efficiency from COD(0.39-0.48l/g·COD· d)were gotten. Some stable and high quantity(10-100times more than sewage sludge)microorganism colony were formed in the reactor. This result provided theoretical basis for anaerobic digestion of black effluent.

红发夫酵母发酵虾青素的研究

红发夫酵母分离于北美西部高山地区和日本一些岛屿上落叶树的渗出液中，因其所产主要色素为在水产养殖、食品和医药工业有广阔应用前景的虾青素而成为研究的热点。本论文对红发夫酵母Phaffia rhodozyma 的生长特性、培养参数与培养基组分对生长和虾青素积累的影响及其优化、虾青素合成的调节控制、虾青素的提取测定及红发夫酵母耐高温菌种的诱变进行了系统的研究。 虾青素是红发夫酵母的胞内色素，要对其进行分析首先要对红发夫酵母进行破壁处理，实验发现二甲亚砜是最有效的破壁溶剂，用氯仿和丙酮可以有效地把类胡萝卜素从二甲亚砜破壁后的红发夫酵母细胞中提取出来。 在固定摇床转速为200 rpm，温度为20 ℃的条件下，当种龄为36 h，以10％的接种量接入装液量为30 mL的250 mL三角瓶，初始pH为5.5时最有利于红发夫酵母的生长及类胡萝卜素的合成。 本实验中红发夫酵母最佳利用碳、氮源分别为蔗糖和蛋白胨，但蛋白胨价格昂贵，不适宜作单一氮源，因此使用硫酸铵和酵母膏作为复合氮源。 本论文采用了BP神经网络结合遗传算法的方法来优化红发夫酵母的发酵培养基，得到红发夫酵母发酵培养基的最佳配比为：蔗糖45.10 g/L、硫酸铵3.00 g/L、硫酸镁0.80 g/L、磷酸二氢钾1.40 g/L、酵母膏3.00 g/L、氯化钙0.50 g/L，使用优化后的培养基发酵类胡萝卜素产量达到8.20 mg/L，干重达到9.47 g/L，类胡萝卜素的产量比起始培养基提高了95.90%，干重提高了89.40%。 从代谢途径出发对红发夫酵母合成虾青素调控调控，选择谷氨酸、乙醇、VB1作为添加剂，通过正交试验设计得出三者添加水平分别为0.2 g/L，0.1% (V/V)，10 mg/L时，类胡萝卜素产量提高了25.73%，达到了10.31mg/L。 通过上述优化培养，本论文中红发夫酵母的虾青素产量从1.33 mg/L提高到9.12 mg/L，产量提高了6.86倍；总类胡萝卜素产量从4.23 mg/L提高到10.31 mg/L，产量提高了2.44倍；细胞干重从5.00 g/L提高到11.35 g/L，提高了2.27倍，总体提高效果显著。 红发夫酵母属于中低温菌，本论文采用紫外复合诱变的方式，通过高温筛选，得到一株能在35 ℃下能生长的突变株，但所产类胡萝卜素中虾青素所占比例很小，可能是诱变改变了红发夫酵母的代谢途径，阻断了虾青素的合成。 Phaffia rhodozyma is a heterobasidiomyceteous yeast that was originally isolated from the slime fluxes of brich tree wounds in mountain regions of northern Japan and southern Alaska. Phaffia rhodozyma produces astaxanthin as its principal carotenoid pigment, which has potential applications in acquaculture, food and pharmaceutical industry. This paper researched ways to break cell, analysis of astaxanthin, characteristics of growth, culture parameters and the effects of components of medium on growth and astaxanthin formation , optimization of culture medium, control of astaxanthin synthesis and mutagenesis of Phaffia rhodozyma. It is necessary to disrupt the yeast cell for extracting astaxanthin considering the yeast accumulating carotenoids in cell. Dimethyisulphoxide was the most effective solvent for breaking the yeast cell; acetone and chloroform were effective to extract carotenoids out of the disrupted cell. The optimum pH for growth and carotenoids synthesis is 5.5, the optimum medium volume is 30 mL (in 250 mL flask), the optimum culture time of inoculum is 36 h, the optimum inoculum concentration is 10%. The research on culture medium showed: sucrose is the best one of 6 carbon sources for growth and astaxanthin synthesis. Peptone is the best nitrogen source for growth and astaxanthin synthesis. Uniform Design was used for trial design of the formula medium components, then back-propagation neural network was established to modeling the relationships between the carotenoid yield and the concentration of medium components. Genetic algorithm (GA) was used for global optimization of the model. The optimum combination of the medium was obtained: sucrose 45.10 g/L, ammonium sulfate 3.00 g/L, magnesium sulfate 0.80 g/L, potassium dihydrogen phosphate 1.40 g/L, yeast extract 3.00 g/L, calcium chloride 0.50 g/L. The yield of carotenoid reached 8.20 mg/L, which was 95.90% higher than that of the original medium. Glu, VB1 and ethanol were selected as fermentation addictives, after Orthogonal Test, the carotenoid contents increased by 25.73% when adding 0.16 g/L Glu, VB1 10 mg/L and ethanol 0.1% (V/V). After the above optimization, the astaxanthin content increased 6.86 folds, which is 9.12 mg/L. The carotenoids content increased 2.44 folds, which is 10.31 mg/L. The biomass increased 2.27 folds, which is 11.35 g/L. Phaffia rhodozyma grows in the mild temperature range of 0 to 27 ℃, in this work, a thermotolerant mutant was selected through UV-irradiation. It can grows at 35 ℃, and showed increased carotenoid content. The optimal growth temperature for this mutant is 30 ℃. But the mutant can only produce carotenoids with little astaxanthin accumulation.

Characteristics of carbonate content and carbon and oxygen isotopic composition of northern China soil and dust aerosol and its application to tracing dust sources

IEECAS SKLLQG

Structure of an unexpected trimer from the reaction of ageratochromene II with aluminum chloride

A new trimer from the reaction of ageratochromene [1] (6,7-dimethoxy-2,2-dimethyl-1-benzopyran) with anhydrous aluminum chloride was shown to be 3,4-dihydro-6,7-dimethoxy-2,2-dimethyl-3-(6',7'-dimethoxy-2',2'-di-methyl-2H-1-benzopyran-4'-yl)-4-(3" 4"-dihydro-6", 7"-dimethoxy-2",2"-dimethyl-2H-1-benzopyran-3"-yl)-2H-1-benzopyran. Its structure was confirmed by NMR (H-1, C-13, DEPT-135. COSY, HMBC, HSQC, TOCSY and NOESY), IR, mass spectra and elemental analysis. Copyright (C) 2002 John Wiley Sons, Ltd.

Determination of lead using a poly(vinyl chloride)-based crown ether membrane

A poly(vinyl chloride)(PVC)-based membrane of 15-crown-5 exhibits a good response for lead(II) ions over a wide concentration range. The response time of the sensor is 30 s and the membrane can be used for more than four months without observing any divergence. The selectivity of the sensor is comparable with those reported for other such electrodes. It was possible to determine lead in polluted waters using this electrode assembly.

Temperature sensitivity of soil respiration is affected by prevailing climatic conditions and soil organic carbon content: A trans-China based case study

National Natural Science Foundation of China [30590381]; Knowledge Innovation Program of the Chinese Academy of Sciences [KZCX2YW-432]; International Partnership Project

Effect of the nucleating agent 1,3 : 2,4-di(3,4-dimethylbenzylidene) sorbitol on the gamma phase content of propylene/ethylene copolymer

The influence of the concentration of a nucleating agent (NA), namely 1,3:2,4-di(3,4-dimethylbenzylidene) sorbitol (DMDBS), on the gamma phase content in a propylene/ethylene copolymer was investigated by means of Differential Scanning Calorimetry (DSC), Wide-Angle X-ray Diffraction (WAXD), Small- Angle X-ray Scatter (SAXS) and Polarized Optical Microscopy (POM).

Phase Behavior and self-assembly of poly[N-vinylformamide-co-(acrylic acid)] copolymers under highly acidic conditions

Copolymers of N-vinylformamide and acrylic acid were synthesized by conventional aqueous free-radical polymerization. The phase behavior of the copolymer solutions was investigated through the addition of hydrochloric acid and the variation of the temperature. With a moderate content of N-vinylformamide, the copolymers showed complex phase behaviors. Under low-acidity conditions, a suspending liquid was formed, whereas under high-acidity conditions, the random copolymers could assemble into round nanoparticles with a broad particle size distribution.

Polyamide thin film composite membranes prepared from isomeric biphenyl tetraacyl chloride and m-phenylenediamine

Three novel of isomeric tetra-functional biphenyl acid chloride: 3,3',5,5'-biphenyl tetraacyl chloride (mm-BTEC), 2,2',4,4'-biphenyl tetraacyl chloride (om-BTEC), and 2,2',5,5'-biphenyl tetraacyl chloride (op-BTEC) were synthesized, and used as new monomers for the preparation of the thin film composite (TFC) reverse osmosis (RO) membranes through interfacial polymerization with m-phenylenediamine (MPDA). The results of membrane performance test showed that membranes prepared from om-BTEC and op-BTEC had higher flux at the expanse of rejection compared with membranes prepared from mm-BTEC.

White light emission on amplified spontaneous emission with dye content controlled polymer system

White light emission from amplified spontaneous emission (ASE) was realized by optically pumping fluorescent dye 4-(dicy-anomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) doped semiconducting poly(9,9-dioctylfluorene) (PFO) polymer thin films. Two individual ASE peaks originating from DCJTB and PFO were observed by carefully controlling the DCJTB concentration in PFO. The studies of the ASE characteristics of DCJTB:PFO thin films lead to the conclusion that the DCJTB:PFO system with 0.3% w/w DCJTB dopant concentration in PFO showed the best ASE performance.

Synthesis of Liquid Polybutadiene Having Desired 1,2-Vinyl Content with Co(naph)(2)-Al-2(C2H5)(3)Cl-3-P(OPh)(3) Catalyst System

Liquid polybutadiene with desirable 1,2-units content was synthesized by Co(naph)(2)-Al-2(C2H5)(3)Cl-3-P(OPh)(3) catalyst system. It was shown that liquid polybutadiene having adequate 1,2-unit content (vinvl =35%-40%) molecular weight(M-n = 700-3500), and acceptabele conversion(>= 55%) can synthesized after optimizing polymerization conditions.

Electrolytic Deposition and Diffusion of Lithium onto Magnesium-9 Wt Pct Yttrium Bulk Alloy in Low-Temperature Molten Salt of Lithium Chloride and Potassium Chloride

The electrolytic deposition and diffusion of lithium onto bulk magnesium-9 wt pct yttrium alloy cathode in molten salt of 47 wt pct lithium chloride and 53 wt pct potassium chloride at 693 K were investigated. Results show that magnesium-yttrium-lithium ternary alloys are formed on the surface of the cathodes, and a penetration depth of 642 mu m is acquired after 2 hours of electrolysis at the cathodic current density of 0.06 A center dot cm(-2). The diffusion of lithium results in a great amount of precipitates in the lithium containing layer. These precipitates are the compound of Mg41Y5, which arrange along the grain boundaries and hinder the diffusion of lithium, and solid solution of yttrium in magnesium. The grain boundaries and the twins of the magnesium-9 wt pct yttrium substrate also have negative effects on the diffusion of lithium.

A strategy of fabricating exfoliated thermoplastic polyurethane/clay nanocomposites via introducing maleated polypropylene

By reducing the attraction between the platelets of octaclecylammonium chloride modified montmorillonite (OMMT-C18) via pre-intercalation of maleated polypropylene (MAPP), OMMT-C18 was exfoliated in thermoplastic polyurethane (TPU) matrix during melt-mixing. Wide angle X-ray diffraction, transmission electron microscopy and thermogravimetric analysis were used to investigate the microstructure of TPU nanocomposites. Three factors (including introducing sequence, the kind and the content of MAPP) showed important effects on the dispersion degree of OMMT-C18 in TPU matrix. The results confirmed that the pre-intercalation of MAPP was necessary for the exfoliation of OMMT-C18; however, the role of MAPP in TPU nanocomposites was different from that in polypropylene nanocomposites.