Test of a microlysimeter for measurement of soil evaporation

Quantifying soil evaporation is required on studies of soil water balance and applications aiming to improve water use efficiency by crops. The performance of a microlysimeter (ML) to measure soil evaporation under irrigation and non-irrigation was evaluated. The MLs were constructed using PVC tubes, with dimensions of 100 mm inner diameter, 150 mm depth and 2.5 mm wall thickness. Four MLs were uniformly distributed on the soil surface of two weighing lysimeters conducted under bare soil, previously installed at Iapar, in Londrina, PR, Brazil. The lysimeters had 1.4 m width, 1.9 m length and 1.3 m depth and were conducted with and without irrigation. Evaporation measurements by MLs (E ML) were compared with measurements by lysimeters (E L) during four different periods in the year. Differences between E ML and E L were small either for low or high atmospheric demand and also for either irrigated or non-irrigated conditions, which indicates that the ML tested here is suitable for measurement of soil evaporation.

Measurement systems of soil water matric potential and evaluation of soil moisture under different irrigation depths

The development of new methodologies and tools that enable to determine the water content in soil is of fundamental importance to the practice of irrigation. The objective of this study was to evaluate soil matric potential using mercury tensiometer and puncture digital tensiometer, and to compare the gravimetric soil moisture values obtained by tensiometric system with gravimetric soil moisture obtained by neutron attenuation technique. Four experimental plots were maintained with different soil moisture by irrigation. Three repetitions of each type of tensiometer were installed at 0.20 m depth. Based on the soil matric potential and the soil water retention curve, the corresponding gravimetric soil moisture was determined. The data was then compared to those obtained by neutron attenuation technique. The results showed that both tensiometric methods showed no difference under soil matric potential higher than -40 kPa. However, under drier soil, when the water was replaced by irrigation, the soil matric potential of the puncture digital tensiometer was less than those of the mercury tensiometer.

Energetic sustainability of three arabica coffee growing systems used by family farming units in Espírito Santo state

Three growing systems of Arabica coffee were evaluated under the energy perspective, in the state of Espírito Santo in Brazil. The systems are conventional cultivation (CC), cultivation with good agricultural practices (CGP) and organic farming (OF). It was made a comparison of the energy flows within these three systems to show sustainable levels of each one based on production average data of several family-farming units. Therefore, we analyzed crop yield, total energy efficiency reverse (TEER), energy efficiency of ripe coffee (EERC) and non-renewable energy efficiency (NREE). OF system had values for TEER, EERC and NREE of 3.3 4.7 and 7.9 respectively. Yet CC showed values of 1.8, 1.9 and 1.6 for TEER, EERC and NREE respectively. Furthermore, CGP presented values for TEER, EERC and NREE of 0.7, 1.3 and 1.4 respectively. The highest yield was observed in CGP, reaching an amount of 1794 kg ha-1(17,455 MJ); however, this system expends more energy than it converts. Thus, over those points, OF is the most sustainable system.

Design of Pulsed Electroacoustic Measurement System for Space Charge Characterisation

Pulsed electroacoustic (PEA) method is a commonly used non-destructive technique for investigating space charges. It has been developed since early 1980s. These days there is continuing interest for better understanding of the influence of space charge on the reliability of solid electrical insulation under high electric field. The PEA method is widely used for space charge profiling for its robust and relatively inexpensive features. The PEA technique relies on a voltage impulse used to temporarily disturb the space charge equilibrium in a dielectric. The acoustic wave is generated by charge movement in the sample and detected by means of a piezoelectric film. The spatial distribution of the space charge is contained within the detected signal. The principle of such a system is already well established, and several kinds of setups have been constructed for different measurement needs. This thesis presents the design of a PEA measurement system as a systems engineering project. The operating principle and some recent developments are summarised. The steps of electrical and mechanical design of the instrument are discussed. A common procedure for measuring space charges is explained and applied to verify the functionality of the system. The measurement system is provided as an additional basic research tool for the Corporate Research Centre of ABB (China) Ltd. It can be used to characterise flat samples with thickness of 0.2–0.5 mm under DC stress. The spatial resolution of the measurement is 20 μm.

Developing the measurement and management of knowledge: applying the constructive research approach in a knowledge intensive service environment

Intellectual assets have attained continuous attention in the academic field, as they are vital sources of competitive advantage and organizational performance in the contemporary knowledge intensive business environment. Intellectual capital measurement is quite thoroughly addressed in the accounting literature. However, the purpose of the measurement is to support the management of intellectual assets, but the reciprocal relationship between measurement and management has not been comprehensively considered in the literature. The theoretical motivation for this study rose from this paradox, as in order to maximise the effectiveness of knowledge management the two initiatives need to be closely integrated. The research approach of this interventionist case study is constructive. The objective is to develop the case organization’s knowledge management and intellectual capital measurement in a way that they would be closely integrated and the measurement would support the management of intellectual assets. The case analysis provides valuable practical considerations about the integration and related issues as the case company is a knowledge intensive organization in which the know-how of the employees is the central competitive asset and therefore, the management and measurement of knowledge are essential for its future success. The results suggest that the case organization is confronting challenges in managing knowledge. In order to appropriately manage knowledge processes and control the related risks, support from intellectual capital measurement is required. However, challenges in measuring intellectual capital, especially knowledge, could be recognized in the organization. By reflecting the knowledge management situation and the constructed strategy map, a new intellectual measurement system was developed for the case organization. The construction of the system as well as its indicators can be perceived to contribute to the literature, emphasizing of the importance of properly considering the organization’s knowledge situation in developing an intellectual capital measurement system.

Design of Instrument for Knee Joint Kinematics Measurement

This thesis describes the process of design and modeling of instrument for knee joint kinematics measurement that can work for both in-vivo and in-vitro subjects. It is designed to be compatible with imaging machine in a sagittal plane. Due to the invasiveness of the imaging machine, the instrument is designed to be able to function independently. The flexibility of this instrument allows to measure anthropometrically different subject. Among the sixth degree of freedom of a knee, three rotational and one translational degree of freedom can be measured for both type of subject. The translational, proximal-distal, motion is stimulated by external force directly applied along its axis. These angular and linear displacements are measured by magnetic sensors and high precision potentiometers respectively

THE ROLE OF INFORMATION TECHNOLOGY IN CREATING SUSTAINABILITY VALUE FOR FINANCIAL INSTITUTIONS IN 2020 : a scenario planning approach

The growing importance of global sustainability issues has been causing many changes to the financial services industry. Facts such as climate change, social development and the financial crisis in 2008 have been making banks reconsider the manner that they consider environmental, social and economic factors in their decision-making process. At the same time, information technology (IT) has been transforming the financial service industry and its fast development has casted doubts on the way it should be managed within an organization. This current changing environment brings a number of uncertainties to the future that cannot be addressed using traditional forecasting techniques. This research investigates how IT can bring value to sustainability in the financial service industry in 2020. Through the use of a scenario planning technique, we analyzed how trends in the current environment (considering the relation between sustainability, financial institutions an IT) can lead to four different future scenarios. Then, we discussed how IT can improve a bank’s sustainability performance, considering the limitations of each scenario.

Disruptive innovations at the bottom of the pyramid : can they impact the sustainability of today´s top companies?

Due to the different dynamics required for organizations to serve the emerging market which contains billions of people at the bottom of the pyramid (BOP) coupled with the increasing desire for organizations to grow and be more multinational, organizations need to continually innovate. However, the tendency for large and established companies to ignore the BOP market and rather focus on existing markets, gives an indication of the existence of a vulnerability that potentially disruptive innovations from the BOP will not be recognized in good time for a counter measure. This can be deduced from the fact that good management practice advocates that managers should learn and listen to their customers. Therefore majority of the large existing companies continually focus on their main customer/market with sustaining innovations which leaves aspiring new entrants with an underserved BOP market to experiment with. With the aid of research interviews and an agent-based model (ABM) simulation, this thesis examines the attributes of BOP innovations that can qualify them as disruptive and the possibilities of tangible disruptive innovations arising from the bottom of the pyramid and their underlying drivers. The thesis Furthermore, examines the associated impact of such innovations on the future sustainability of established large companies that are operating in the developed world, particularly those with a primary focus which is targeted towards the market at the top of the pyramid (TOP). Additionally, with the use of a scenario planning model, the research provides an evaluation of the possible evolution and potential sustainability impacts that could emerge, from the interplay of innovations at the two pyramidal market levels and the chosen market focus of organizations – TOP or BOP. Using four scenario quadrants, the thesis demonstrates the resulting possibilities from the interaction between the rate of innovations and the segment focused on by organizations with disruptive era characterizing the paradigm shift quadrant. Furthermore, a mathematical model and two theoretical propositions are developed for further research. As recommendations, the thesis also extends the ambidextrous organizational theory, business model innovation and portfolio diversification as plausible recommendations to limit a catastrophic impact, resulting from disruptive innovations.

Genetic analysis and cAMP measurement: comparison between lean and obese anovulating mice

PURPOSE: To evaluate genes differentially expressed in ovaries from lean (wild type) and obese (ob/ob) female mice and cyclic AMP production in both groups.METHODS: The expression on messenger RNA levels of 84 genes concerning obesity was analyzed through the PCR array, and cyclic AMP was quantified by the enzyme immunoassay method.RESULTS: The most downregulated genes in the Obesity Group included adenylate cyclase-activating polypeptide type 1, somatostatin, apolipoprotein A4, pancreatic colipase, and interleukin-1 beta. The mean decrease in expression levels of these genes was around 96, 40, 9, 4.2 and 3.6-fold, respectively. On the other hand, the most upregulated genes in the Obesity Group were receptor (calcitonin) activity-modifying protein 3, peroxisome proliferator activated receptor alpha, calcitonin receptor, and corticotropin-releasing hormone receptor 1. The increase means in the expression levels of such genes were 2.3, 2.7, 4.8 and 6.3-fold, respectively. The ovarian cyclic AMP production was significantly higher in ob/ob female mice (2,229±52 fMol) compared to the Control Group (1,814±45 fMol).CONCLUSIONS: Obese and anovulatory female mice have reduced reproductive hormone levels and altered ovogenesis. Several genes have their expression levels altered when leptin is absent, especially adenylate cyclase-activating polypeptide type 1.

Rasvankestävät paperit ja kartongit

Rasvankestävyydellä tarkoitetaan sitä, että materiaali hylkii tai kestää rasvaa tietyn ajan läpäisemättä sen pintaa. Rasvankestäviä papereita ja kartonkeja löytyy kaikkialta. Erilaiset ruuanvalmistuspaperit, kuten esimerkiksi leivinpaperi ja voipaperi, ovat rasvankestäviä. Myös pakkauksissa käytetään paljon rasvankestäviä papereita ja kartonkeja. Rasvankestäviltä tuotteilta vaaditaan erilaisia ominaisuuksia riippuen niiden käyttötarkoituksesta. Pakkausmateriaaleilta vaaditaan esimerkiksi lujuutta ja kestävyyttä fyysistä rasitusta, valoa, hajuja ja mikrobeja vastaan. Ruuanvalmistusmateriaaleilta vaaditaan puolestaan lujuutta ja kestävyyttä lämpöä, kosteutta ja fyysistä rasitusta vastaan. Rasvankestäviltä papereilta vaaditaan rasvankestävyyden lisäksi hyvää vetolujuutta, märkälujuutta ja hyviä optisia ominaisuuksia. Neliömassan tulee asettua 20─80 g/m2 välille ja metallipitoisuudet eivät saa olla liian korkeat. Myös tuotteiden kierrätettävyys on nostanut asemaansa viimeaikoina. Tuotteen tuotannon ja itse tuotteen ympäristöystävällisyys ovat todella arvostettuja kuluttajan, tuottajan, Suomen, EU:n ja koko maailman näkökulmista. Jotta tuotteesta saadaan rasvankestävää, vaaditaan siltä erilaisia barrier-ominaisuuksia. Rasvankestävällä paperilla vaaditaan hyviä barrier-ominaisuuksia esimerkiksi rasvan, ilman, veden, vesihöyryn sekä hapen läpäisevyyksissä. Rasvankestäviä papereita ja kartonkeja voidaan valmistaa kemiallisilla ja mekaanisilla tavoilla. Happokäsittely ja fluorokemikaalien lisääminen ovat kemiallisia tapoja, kun taas sellun jauhaminen pitkään matalassa lämpötilassa on mekaaninen tapa valmistaa rasvankestävää paperia. Näiden tapojen lisäksi rasvankestäviä papereita voidaan tehdä erilaisten pinnoitusten avulla. Erilaiset muovit ovat yleisemmin käytettyjä pinnoitemateriaaleja. Esimerkiksi PE- ja PET-päällysteet ovat käytettyjä rasvankestävissä tuotteissa. Viime aikoina on kehitetty paljon erilaisia biomateriaaleja, joista voidaan tehdä rasvankestävä pinnoite. Lipideistä, hydrokolloideista ja erilaisista komposiiteista voidaan luoda uusien tekniikoiden avulla rasvankestäviä pinnoitteita. Rasvankestävyydestä voidaan saada jonkinlainen käsitys WVTR-asteen, Cobb-arvon ja kontaktikulman mittausten avulla. Rasvankestävyyttä voidaan myös mitata erilaisten standarditestien avulla. TAPPI:lla, ISO:lla ja ASTM:llä on useita erilaisia standardeja. Lähes kaikissa rasvankestävyysstandardeissa tuloksen saaminen perustuu visuaaliseen havaintoon, mikä aiheuttaa välillä hankaluuksia tulosten luotettavuuteen, koska tuloksen määrittää ihmissilmä, ja kaikilla testin tekijöillä on erilainen silmä, joka aistii eri tavalla.

Customer profitability measurement in a not-for-profit organization

The objective of this study was to find out the factors that affect customer profitability in the not-for-profit case company. The customer profitability was examined in two different segments of the customer base. The effects that price, cost and the amount of services provided have on the profit margin were studied. The distribution of profitability among the customers and the effect of certain characteristics, such as size of the customer measured in services purchased, on the profitability were analyzed. The theoretical framework was built around customer profitability and the use of customer profitability information in a not-for-profit organization. The present use of customer profitability information and the possibilities of using the results of this research in the case company were presented. Quantitative research methods were used in the empirical part of the study. The results indicate that the two customer segments have differences in their buying behaviors which affect the profitability and thus the measures taken to improve the profitability should be considered with the different characteristics of the customers in mind. Finally the limitations of the study were discussed as possible further research topics.

Design of an amplifier and an instrumentation setup for a harsh environment heat flux measurement application – case axial flux electric machine

Measurement is a tool for researching. Therefore, it is important that the measuring process is carried out correctly, without distorting the signal or the measured event. Researches of thermoelectric phenomena have been focused more on transverse thermoelectric phenomena during recent decades. Transverse Seebeck effect enables to produce thinner and faster heat flux sensor than before. Studies about transverse Seebeck effect have so far focused on materials, so in this Master’s Thesis instrumentation of transverse Seebeck effect based heat flux sensor is studied, This Master’s Thesis examines an equivalent circuit of transverse Seebeck effect heat flux sensors, their connectivity to electronics and choosing and design a right type amplifier. The research is carried out with a case study which is Gradient Heat Flux Sensors and an electrical motor. In this work, a general equivalent circuit was presented for the transverse Seebeck effect-based heat flux sensor. An amplifier was designed for the sensor of the case study, and the solution was produced for the measurement of the local heat flux of the electric motor to improve the electromagnetic compatibility.

Heat flux measurement inside internal combustion engine with gradient heat flux sensor.

This master’s thesis is devoted to study different heat flux measurement techniques such as differential temperature sensors, semi-infinite surface temperature methods, calorimetric sensors and gradient heat flux sensors. The possibility to use Gradient Heat Flux Sensors (GHFS) to measure heat flux in the combustion chamber of compression ignited reciprocating internal combustion engines was considered in more detail. A. Mityakov conducted an experiment, where Gradient Heat Flux Sensor was placed in four stroke diesel engine Indenor XL4D to measure heat flux in the combustion chamber. The results which were obtained from the experiment were compared with model’s numerical output. This model (a one – dimensional single zone model) was implemented with help of MathCAD and the result of this implementation is graph of heat flux in combustion chamber in relation to the crank angle. The values of heat flux throughout the cycle obtained with aid of heat flux sensor and theoretically were sufficiently similar, but not identical. Such deviation is rather common for this type of experiment.