Development of a pressure nociceptive threshold testing device for evaluation of analgesics in cats

A pressure analgesiometric device was developed for unrestrained cats. Eleven cats were studied. Stimulation was via three rounded pins within a bracelet on the forearm. The pins were advanced by manual bladder inflation. Bladder pressure was measured using a strain gauge pressure transducer. The threshold was recorded at the behavioural end point. Thresholds were measured at 5 and 15 min intervals for 2-4 h, after removal/replacement of the cuff, for 120 min after SC butorphanol (0.4 mg/kg), and with mild skin inflammation at the testing site. Data were analysed using ANOVA. Pressure thresholds in untreated cats were around 150 mmHg. The minimum interval for testing was established as 15 min. Data were reproducible over 4 h and beyond 24 h. Thresholds in 5 cats increased (P < 0.05) above baseline for 45 min after butorphanol with a maximum increase of 270 +/- 182 mmHg at 10 min. Thresholds decreased with inflammation. The method appears suitable for feline analgesia investigations. (c) 2006 Elsevier Ltd. All rights reserved.

Evaluation of Bi as internal standard to minimize matrix effects on the direct determination of Pb in vinegar by graphite furnace atomic absorption spectrometry using Ru permanent modifier with co-injection of Pd/Mg(NO3)(2)

Bismuth was evaluated as an internal standard for the direct determination of Pb in vinegar by graphite furnace atomic absorption spectrometry using Ru as a permanent modifier with co-injection of Pd/Mg(NO3)(2). The correlation coefficient of the graph plotted from the non-nalized absorbance signals of Bi versus Pb was r=0.989. Matrix effects were evaluated by analyzing the slope ratios between the analytical curve, and analytical curves obtained from Pb additions in red and white wine vinegar obtained from reference solutions prepared in 0.2% (v/v) HNO3, samples. The calculated ratios were around 1.04 and 1.02 for analytical curves established applying an internal standard and 1.3 and 1.5 for analvtical curves without. Analytical curves in the 2.5-15 pg L-1 Pb concentration interval were established using the ratio Pb absorbance to Bi absorbance versus analvte concentration, and typical linear correlations of r=0.999 were obtained. The proposed method was applied for direct determination of Pb in 18 commercial vinegar samples and the Pb concentration varied from 2.6 to 31 pg L-1. Results were in agreement at a 95% confidence level (paired t-test) with those obtained for digested samples. Recoveries of Pb added to vinegars varied from 96 to 108% with and from 72 to 86% without an internal standard. Two water standard reference materials diluted in vinegar sample were also analyzed and results were in agreement with certified values at a 95% confidence level. The characteristic mass was 40 pg Pb and the useful lifetime of the tube was around 1600 firings. The limit of detection was 0.3 mu g L-1 and the relative standard deviation was <= 3.8% and <= 8.3% (n = 12) for a sample containing, 10 mu L-1 Pb with and without internal standard, respectively. (C) 2007 Elsevier B.V. All rights reserved.

Ba1-xSrxTiO3 thin films by polymeric precursor method

Stoichiometric Ba1-xSrxTiO3 (BST; x = 0.4) thin films were prepared by the polymeric precursor method. High quality polycrystalline films of BST with low roughness (approximate to 3 nm) were obtained from a Pt/Ti/SiO2/Si substrate deposited by spin-coating technique. Microstructure and morphological evaluation were done using grazing incident X-ray diffraction (GIXRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM). Grazing incident angle XRD characterization of these films showed that BST phase crystallizes at 600 degrees C from an inorganic amorphous matrix. No intermediate crystalline phase was identified. A linear relationship between roughness and grain size was observed. (C) 2000 Elsevier B.V. B.V. All rights reserved.

Evaluation of the performance of pharmacists in terms of providing health assistance at a university hospital

OBJETIVE: This study aimed to assess the practices of pharmacists in Hospital Care. Method - we interviewed 20 pharmacists from the Pharmacy Division by applying a structured instrument, in September 2005. This instrument addressed aspects related to the main activities at the Hospital Pharmacy, which were assessed according to indicators organized into five areas: sector management, hospital pharmacotechniques, committee activities, information and pharmacotherapeutic follow-up, as well as teaching and research activities.RESULTS: the Pharmacy Division considered all structural aspects under analysis as essential for the good development and application of its services. We found that some essential services, such as the Medication Information Service and Pharmacotherapeutic Follow-up, were absent. Pharmacist professionals were dissatisfied about human resource and physical structure dimensioning, and they presented as not very active in terms of Pharmaceutical Care.CONCLUSION: Results indicate that care is still centered on the drug, with few clinical activities. We suggest reformulations in service management, particularly in the management of pharmacists.

Evaluation of cutting patterns produced in primary teeth by an air-abrasion system

Objective: the aim of this in vitro study was to assess the effect of tip diameter, nozzle distance, and application time of an air-abrasion system for cavity preparation on the enamel of primary teeth. Method and materials: Forty exfoliated primary teeth were air abraded with a microabrasion machine used with a handpiece with an 80-degree-angle nozzle, 50-mum abrasive particle size, and 80-psi air pressure. The effects of 0.38- or 0.48-mm inner tip diameter, 2- or 5-mm distance from tip to tooth surface, and 15 or 30 seconds of application time on cutting efficiency were evaluated. Cutting width and depth were analyzed and measured from scanning electron micrographs. Results: Statistical analysis revealed that the width of the cuts was significantly greater when the tip distance was increased. Significantly deeper cavities were produced by a tip with a 0.48-mm inner diameter. The application time did not influence the cuts. Conclusion: the cutting patterns found in this study suggest that precise removal of enamel in primary teeth is best accomplished when a tip with a 0.38-mm inner diameter is used at a 2-mm distance.

Determination of soybean seed respiration rate by the titulation method

This trial was carried out under laboratory conditions, with three lots of Iguacu soybean seeds, to determine the respiration rate by the titulation method. A randomized complete block design was used, with four repetitions, each one of them with 50 seeds and a control without seeds for each lot. The seeds were placed in gerbox with 40 mi of KOH 0.1N, on distilled water wet blotting paper for fixing the CO2 produced by seeds respiration. The material was placed in germinator at constant 25 degrees C for 16, 24 and 48 hours. After these periods, the titulation of the fixative solution was performed with HCl 0.1N to check the respiration rate. The most deteriorated seeds were those that presented the highest respiration rates, which were measured in mg of CO2/g of dry matter, when compared with the most vigorous lots. The titulation method was suitable for the evaluation of soybean seed respiration rate because the final results separated the lots in three different quality levels that were compatible with the results obtained from the accelerated aging and emergence.

Kinetic evaluation of the pyrolysis of high density polyethylene over H-AlMCM-41 material

The AlMCM-41 material with Si/Al=50 was synthesized by hydrothermal method, using cethyltrimethylammonium as template. The protonic H-AlMCM-41 acid form was obtained by ion exchange with ammonium chloride solution and subsequent calcination. The characterization of the material by several techniques showed that a good-quality MCM-41 material was obtained. High-density polyethylene (HDPE) has been submitted to thermal degradation alone, and in presence of the exchanged H-AlMCM-41 catalyst at a concentration of 1: 1 in mass (H-AlMCM-41/HDPE). The reactor was connected on line to a gas chromatograph connected to a mass spectrometer. This process was evaluated by thermogravimetry (TG), from 350 to 600degreesC, under helium dynamic atmosphere, with heating rates of 5.0; 10.0 and 20.0 degreesC/min. From TG curves, the activation energy, calculated using a multiple heating rate integral kinetic method, decreased from 225.5 KJ.mol(-1), for the pure polymer (HDPE), to 184.7 KJ.mol(-1), in the presence of the catalyst (H-AlMCM-41/HDPE).

Use of reduced concentrations of tetrazolium solutions for the evaluation of the viability of peanut seed lots

The possibility of reducing the concentration of the working solution used in the tetrazolium test for peanut seeds (Arachis hypogaea L.) with or without seedcoats was studied. Tetrazolium solutions of different concentrations (0.05%, 0.075% and 0.1%) were tested at the temperatures of 35 and 40 degrees C, for determining the time needed for the seeds to reach proper staining. The efficiency of the selected treatments in evaluating the viability potential of the seeds was determined by comparing the results of the tetrazolium tests with those obtained by standard germination (using sand and rolled paper towel as substrata) and seedling emergence in the field tests. Staining the seeds without seedcoat in 0.05% tetrazolium solution for three hours at 40 degrees C yielded efficient results. on the other hand, reduced concentrations can be employed in the staining process of seeds with seedcoat; however, this method requires a higher consumption of tetrazolium salt, longer staining time as well as a higher ability and availability of time for embryo evaluation, since the cross-cutting of seeds is much more difficult in the presence of the seedcoat and the occurrence of damage to the outer surface of the cotyledons cannot be determined.

Development of new standard procedures for the evaluation of dental composite abrasive wear

This article discusses the development of a test bench and a methodology for the study of composite resin abrasive wear. To evaluate the operation of the test bench and to compare the proposed methodology with other existing ones, a study was made of the five composites most commonly used by dentists.The one-way ANOVA method and the Tukey test were used to statistically analyze the results by multiple comparisons of the groups of resins tested. Using the proposed methodology, these resins were classified in an increasing order of abrasive wear strength, as follows: Charisma (the lowest abrasive wear strength), Tetric, TPH, Herculite and Z-100 (the highest abrasive wear strength) (P < 0.05). In comparison to other methodologies, the results of the proposed methodology presented the lowest coefficient of variation. (C) 2002 Elsevier B.V. B.V. All rights reserved.

Evaluation of isopathic treatment of Salmonella enteritidis in poultry

Background. Salmonellosis is a common problem worldwide in commercially reared poultry. It is associated with human Salmonellosis. No fully satisfactory method of control is available.Method: Nosodes to an antibiotic-resistant strain of Salmonella enterica serovar Enteritidis in D30 (30X) potency were prepared. One day old chicks (N = 180) were divided into four groups: two control and two different preparations of the nosode. Treatments were administered in drinking water for 10 days. The birds were challenged by a broth culture of the same Salmonella, by mouth, on day 17. Cloacal swabs were taken twice weekly for Salmonella enterica serovar Enteritidis.Results: Birds receiving active treatment were less likely to grow the strain of Salmonella from cloacal swabs compared to control.Conclusion: Isopathy is low cost and non-toxic. It may have a role to play in the widespread problem of Salmonella in poultry. Further research should be conducted.

Evaluation of sample treatment for the simultaneous flow injection hydride generation and determination of As, Bi, Sb and Se by GRAS

A new method was developed for the simultaneous determination of As, Bi, Sb, and Se by flow injection hydride generation graphite furnace atomic absorption spectrometry. An alternative two-step sample treatment procedure was used. The sample was heated (80degreesC) for 10 min in 6 M HCl to reduce Se(VI) to Se(IV), followed by the addition of 1% (m/v) thiourea solution to reduce arsenic and antimony from the pentavalent to the trivalent states.With this procedure, all analytes were converted to their most favorable and sensitive oxidation states to generate the corresponding hydrides. The pre-treated sample solution was then processed in the flow system for in situ trapping and atomization in a graphite tube coated with iridium. The impermanent modifier remained stable up to 300 firings and new coating out significant were possible wit changes in the analytical performance.The accuracy was checked for As, Bi, Sb, and Se determination in water standard reference materials NIST 1640 and 1643d and the results were in agreement with the certified values at a 95% confidence level. Good recoveries (94-104%.) of spiked mineral waters and synthetic As(V), Sb(Ill), mixtures of As(Ill), Sb(V), Se(VI), and Se(IV) were also found. Calculated characteristic masses were 32 mug As, 79 mug Bi, 35 mug Sb, and 130 pg Se, and the corresponding limits of detection were 0.06, 0.16, 0.19, and 0.59 mug L-1, respectively. The repeatability for a typical solution containing 5 mug L-1 As, Bi, Sb, and Se was in the 1-3% range.

Gaussian basis sets by generator coordinate Hartree-Fock method to ab initio calculations of electron affinities of enolates

The Generator Coordinate Hartree-Fock (GCHF) method is employed to generate uncontracted 15s and 18s11p gaussian basis sets for the H, C and O atoms, respectively. These basis sets are then contracted to 3s and 4s H atom and 6s5p, for C and O atoms by a standard procedure. For quality evaluation of contracted basis sets in molecular calculations, we have accomplished calculations of total and orbital energies in the Hartree-Fock-Roothaaii (HFR) approach for CH, C(2) and CO molecules. The results obtained with the uncontracted basis sets are compared with values obtained with the standard D95, 6-311G basis sets and with values reported in the literature. The 4s and 6s5p basis sets are enriched with polarization and diffuse functions for atoms of the parent neutral systems and of the enolates anions (cycloheptanone enolate, 2,5-dimethyleyelopentanone enolate, 4-heptanone enolate, and di-isopropyl ketone enolate) from the literature, in order to assess their performance in ab initio molecular calculations, and applied for calculations of electron affinities of the enolates. The calculations were performed at the DFT (BLYP and B3LYP) and HF levels and compared with the corresponding experimental values and with those obtained by using other 6-3 1 + +G((*)) and 6-311 + +G((*)) basis sets from literature. For the enolates studied, the differences between the electron affinities obtained with GCHF basis sets, at the B3LYP level, and the experimental values are -0.001, -0,014, -0.001, and -0.001 eV. (C) 2002 Elsevier B.V. B.V. All rights reserved.

Evaluation of the thermal diffusivity of vegetable oils during frying by Thermal Lens Spectrometry

In this work we report on the use of the Thermal Lens method to verify the evolution of the thermal diffusivity of sunflower and soybean vegetable oils utilized in preparation of twenty five snacks portions. Our results show that the thermal diffusivity for sunflower oil does not change between 1 and 25 portions of fried snacks. By another hand, the soybean thermal diffusivity exhibits a little decrease for higher portion of fried snacks, indicating that for this oil the triglyceride level is reduced as a degradation process.

Analytical method for the design of a machine with aligned and skewed permanent magnets

This work aims to present the design and the evaluation of a standard multi-pole machine with permanent magnets inserted in the rotor by two different geometrical forms: aligned and skewed magnets. The design (new analytical method) was based on a standard 250 W three phase 12-pole induction motor (squirrel cage rotor type), beginning with the original stator constructive data to calculate the magnetic flux density to determine the permanent magnets. In the development of the work, a simple and modular rotor was built reusing the original 12-pole stator (concentrated windings). The machine was evaluated in a laboratory for the purpose of checking the quantity and quality of energy produced with the machine operating as a generator and its start, torque, and performance working as a motor. In conclusion, the modular skewed magnet is an option for electrical machines, for the generation of a reasonable quality, in the context of decentralized generation and a motor with high torque and low energetic consumption.

Evaluation of the microscopic observation drug susceptibility assay for detection of Mycobacterium tuberculosis resistance to pyrazinamide

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)