Development and transient performance results of a single stage activated carbon - HFC 134a closed cycle adsorption cooling system

A laboratory model of a thermally driven adsorption refrigeration system with activated carbon as the adsorbent and 1,1,1,2-tetrafluoroethane (HFC 134a) as the refrigerant was developed. The single stage compression system has an ensemble of four adsorbers packed with Maxsorb II specimen of activated carbon that provide a near continuous flow which caters to a cooling load of up to 5W in the 5-18 degrees C region. The objective was to utilise the low grade thermal energy to drive a refrigeration system that can be used to cool some critical electronic components. The laboratory model was tested for it performance at various cooling loads with the heat source temperature from 73 to 93 degrees C. The pressure transients during heating and cooling phases were traced. The cyclic steady state and transient performance data are presented. (C) 2010 Elsevier Ltd. All rights reserved.

Spectrophotometric and potentiometric investigations of copper (II)-Ethanolamine complexes - Part III. diethanolamine (Gaussian analysis of electronic spectra in mono and diethanolamine systems)

Spectrophotometric and potentiometric investigations have been carried out on copper-diethanolamine system. Job plots at 900, 900 and 580 mμ have indicated the formation of CuD++, CuD2++ and CuD3++. The n- pA curves obtained indicate the formation of CuD++, CuD2++, CuD3++, CuDOH+, CuD2OH+ and CuD3OH+. The n- pA curves have been analyzed to obtain the stability constants of these complexes. Absorption curves of pure complexes have been computed by a graphical method. Gaussian analysis of the absorption curves of pure and hydroxy complexes show the presence of a second band, indicating that the structure is that of a distorted octahedron.

Negative differential conductance and effective electron mass in highly asymmetric ballistic bilayer graphene nanoribbon

We present a simplified theory of the effective momentum mass (EMM) and ballistic current–voltage relationship in a degenerate two-folded highly asymmetric bilayer graphene nanoribbon. With an increase in the gap, the density-of-states in the lower set of subbands increases more than that of the upper set. This results in a phenomenological population inversion of carriers, which is reflected through a net negative differential conductance (NDC). It is found that with the increase of the ribbon width, the NDC also increases. The population inversion also signatures negative values of EMM above a certain ribbon-width for the lower set of subbands, which increases in a step-like manner with the applied longitudinal static bias. The well-known result for symmetric conditions has been obtained as a special case.

Differential binding of peanut agglutinin with lipopolysaccharide of homologous and heterologous Rhizobium

To establish the crucial role of lipopolysaccharide in the initial recognition event of symbiotic peanut-Rhizobium system the ability of various surface polysaccharides isolated from Bradyrhizobium arachis to inhibit the precipitin reaction between peanut agglutinin and asialoganglioside: deoxycholate (1:1) micelles was estimated. It was compared with that of nonsymbiotic systems e.g. Bradyrhizobium japonicum, Bradyrhizobium ciceris and Escherichia coli. Peanut agglutinin was found to interact more strongly with the lipopolysaccharide of Bradyrhizobium arachis than the exopolysaccharide or capsular polysaccharide. The inhibitory capacity of lipopolysaccharides from homologous and heterologous Bradyrhizobium as measured in terms of the concentration necessary for 50 percent inhibition of precipitin reaction were 1428, 500, 410, and 277 times less than that of lactose for Bradyrhizobium arachis, B. japonicum, B. ciceris and Escherichia coli, respectively. These results support that host lectin peanut agglutinin can recognize homologous Bradyrhizobium lipopolysaccharide by virtue of its binding specificity of higher magnitude.

A new approach for fault location identification in transmission system using stability analysis and SVMs

This paper presents a new approach to the location of fault in the high voltage power transmission system using Support Vector Machines (SVMs). A knowledge base is developed using transient stability studies for apparent impedance swing trajectory in the R-X plane. SVM technique is applied to identify the fault location in the system. Results are presented on sample 3-power station, a 9-bus system illustrate the implementation of the proposed method.

Optimal reactive power dispatch based on voltage stability criteria in a large power system with AC/DC and FACTs devices

An algorithm for optimal allocation of reactive power in AC/DC system using FACTs devices, with an objective of improving the voltage profile and also voltage stability of the system has been presented. The technique attempts to utilize fully the reactive power sources in the system to improve the voltage stability and profile as well as meeting the reactive power requirements at the AC-DC terminals to facilitate the smooth operation of DC links. The method involves successive solution of steady-state power flows and optimization of reactive power control variables with Unified Power Flow Controller (UPFC) using linear programming technique. The proposed method has been tested on a real life equivalent 96-bus AC and a two terminal DC system under normal and contingency conditions.

Comparative studies of transient and steady state analysis for a typical 765kV/400kV EHV transmission system in Indian power system

This paper describes an approach for the analysis and design of 765kV/400kV EHV transmission system which is a typical expansion in Indian power grid system, based on the analysis of steady state and transient over voltages. The approach for transmission system design is iterative in nature. The first step involves exhaustive power flow analysis, based on constraints such as right of way, power to be transmitted, power transfer capabilities of lines, existing interconnecting transformer capabilities etc. Acceptable bus voltage profiles and satisfactory equipment loadings during all foreseeable operating conditions for normal and contingency operation are the guiding criteria. Critical operating strategies are also evolved in this initial design phase. With the steady state over voltages obtained, comprehensive dynamic and transient studies are to be carried out including switching over voltages studies. This paper presents steady state and switching transient studies for alternative two typical configurations of 765kV/400 kV systems and the results are compared. Transient studies are carried out to obtain the peak values of 765 kV transmission systems and are compared with the alternative configurations of existing 400 kV systems.

KO2: Realization of Orbital Ordering in a p-Orbital System

KO2 is a molecular solid consisting of oxygen dimers. K present in the lattice donates an electron which goes on to occupy the O p levels.As the basic electronic structure is similar to that of an oxygen molecule, except for broadening due to solid state effects, KO2 represents the realization of the doping of oxygen molecules arranged in a lattice. These considerations alone result in magnetism with high ordering temperatures as our calculations reveal. However, we find that the high temperature structure is unstable to an orbital ordering (OO) transition. The microscopic considerations driving the OO transition, however, are electrostatic interactions instead of the often encountered superexchange driven ordering within the Kugel-Khomskii model often used to describe the OO. This OO transition is also found to preclude any possibility of high magnetic ordering temperatures, which otherwise seemed possible.

Sliding Modes for the Simulation of Mechanical and Electrical Systems Defined by Differential-Algebraic Equations

We offer a technique, motivated by feedback control and specifically sliding mode control, for the simulation of differential-algebraic equations (DAEs) that describe common engineering systems such as constrained multibody mechanical structures and electric networks. Our algorithm exploits the basic results from sliding mode control theory to establish a simulation environment that then requires only the most primitive of numerical solvers. We circumvent the most important requisite for the conventionalsimulation of DAEs: the calculation of a set of consistent initial conditions. Our algorithm, which relies on the enforcement and occurrence of sliding mode, will ensure that the algebraic equation is satisfied by the dynamic system even for inconsistent initial conditions and for all time thereafter. [DOI:10.1115/1.4001904]

Electronic structure of square planar CuO46− clusters

The results of spin-polarized MSXagr calculations show that the ground state of the CuO 4 6– cluster is essentially non-magnetic in spite of odd number of electrons in the system for short Cu–O distances (1.90 Å) as found in the highT c superconductors. This arises due to the fact that the unpaired electron resides in a molecular orbital with primarily oxygen 3s character. The stability of this molecular orbital is found to be sensitive to the cluster geometry and thus, increase in Cu–O distance (as well as other changes affecting oxygen-oxygen distance) tend to favour a magnetic state. From these calculations we have also estimated the Coulomb correlation strength within the Cu 3d to be about 5.3 eV.

Dielectric Properties of Epoxy-Al2O3 Nanocomposite System for Packaging Applications

In recent times, there has been an ever-growing need for polymer-based multifunctional materials for electronic packaging applications. In this direction, epoxy-Al2O3 nanocomposites at low filler loadings can provide an excellent material option, especially from the point of view of their dielectric properties. This paper reports the dielectric characteristics for such a system, results of which are observed to be interesting, unique, and advantageous as compared to traditionally used microcomposite systems. Nanocomposites are found to display lower values of permittivity/tan delta over a wide frequency range as compared to that of unfilled epoxy. This surprising observation has been attributed to the interaction between the epoxy chains and the nanoparticles, and in this paper this phenomenon is analyzed using a dual layer interface model reported for polymer nanocomposites. As for the other dielectric properties associated with the nanocomposites, the nano-filler loading seems to have a significant effect. The dc resistivity and ac dielectric strength of the nanocomposites were observed to be lower than that of the unfilled epoxy system at the investigated filler loadings, whereas the electrical discharge resistant properties showed a significant enhancement. Further analysis of the results obtained in this paper shows that the morphology of the interface region and its characteristics decide the observed interesting dielectric behaviors.

Thermal and electrical switching studies on Ge20Se80-xBix (1 <= x <= 13) ternary chalcogenide glassy system

Alternating Differential Scanning Calorimetric (ADSC) and electrical switching studies have been undertaken on Ge20Se80-xBix glasses (1 <= x <= 13), to understand the effect of topological thresholds on thermal properties and electrical switching behavior. It is found that the compositional dependence of glass transition temperature (Tg), crystallization temperature (T-c1) and thermal stability (AT) of Ge20Se80-xBix glasses show anomalies at a composition x= 5, the rigidity percolation/stiffness threshold of the system. Further, unusual variations are also observed in different thermal properties, such as T-g, T-c1, Delta T, Delta C-p and Delta H-NR, at the composition x= 10, which indicates the occurrence of chemical threshold in these glasses at this composition. Electrical switching studies indicate that Ge20Se8o_RBig glasses with 5 11 exhibit threshold switching behavior and those with x = 12 and 13 show memory switching. A sharp decrease has been noticed in the switching voltages with bismuth concentration, which is due to the more metallic nature of bismuth and the presence of Bi+ ions. Further, a saturation is seen in the decrease in V-T around x = 6, which is related to bismuth phase percolation at higher concentrations of Bi. (C) 2010 Elsevier B.V. All rights reserved.

Electronic structure and conformational study of thiobiurets

Quantum mechanical calculations at all valence complete neglect of differential overlap (CNDO/2) and self-consistent charge extend Huckel (SCC-EH) and the Pi electron Pariser-Parr-Pople with limited configuration interaction (PPP-LCI) levels of approximation have been accomplished for monothiobiuret and dithiobiuret. From the calculated results, a discussion of the electronic structure, photoelectron and electronic spectra and the conformational stability are given. The electronic and1H nmr spectra are also reported. A trans-cis-CONHCS-structure is found to be the stable conformation for monothiobiuret consistent with other evidences.

Interdiffusion studies in bulk Au-Ti system

The performance of the contacts, where Au/Ti layers are used in the metallization scheme, largely depends on the product phases grown by interdiffusion at the interface. It is found that four intermetallic compounds grow with narrow homogeneity range and wavy interfaces in the interdiffusion zone. The presence of wavy interfaces is the indication of high anisotropy in diffusion of the product phases. This also reflects in the deviation of parabolic growth from the average. Further, we have determined the relevant diffusion parameters, such as interdiffusion coefficient in the penetrated region of the end members and integrated diffusion coefficients of the intermetallic compounds.

Optimization and design of energy transport system for solar cooking application

This paper proposes a hybrid solar cooking system where the solar energy is transported to the kitchen. The thermal energy source is used to supplement the Liquefied Petroleum Gas (LPG) that is in common use in kitchens. Solar energy is transferred to the kitchen by means of a circulating fluid. Energy collected from sun is maximized by changing the flow rate dynamically. This paper proposes a concept of maximum power point tracking (MPPT) for the solar thermal collector. The diameter of the pipe is selected to optimize the overall energy transfer. Design and sizing of different components of the system are explained. Concept of MPPT is validated with simulation and experimental results. (C) 2010 Elsevier Ltd. All rights reserved.