Anisotropia magnética (110) em Nanofilmes de Permalloy sobre MgO(100)

The study and fabrication of nanostructured systems composed of magnetic materials has been an area of great scientific and technological interest. Soft magnetic materials, in particular, have had great importance in the development of magnetic devices. Among such materials we highlight the use of alloys of Ni and Fe, known as Permalloy. We present measurement results of structural characterization and magnetic films in Permalloy (Ni81Fe19), known to be a material with high magnetic permeability, low coercivity and small magneto- crystalline anisotropy, deposited on MgO (100) substrates. The Magnetron Sputtering technique was used to obtain the samples with thicknesses varying between 9 150 nm. The techniques of X- ray Diffraction at high and low angle were employed to confirm the crystallographic orientation and thickness of the films. In order to investigate the magnetic properties of the films the techniques of Vibrant Sample Magnetometry (VSM), Ferromagnetic Resonance (FMR) and Magnetoimpedance were used. The magnetization curves revealed the presence of anisotropy for the films of Py/MgO (100), where it was found that there are three distinct axis - an easy-axis for θH = 0°, a hard-axis for θH = 45° and an intermediate for θH = 90°. The results of the FMR and Magnetoimpedance techniques confirm that there are three distinct axes, that is, there is a type C2 symmetry. Then we propose, for these results, the interpretation of the magnetic anisotropy of Py/MgO ( 100 ) is of type simple C2, ie a cubic magnetic anisotropy type ( 110 )

Crescimento de filmes nanométricos monocristalinos de Fe/MgO(100) por "SPUTTERING" DC

The research behind this master dissertation started with the installation of a DC sputtering system, from its first stage, the adaptation of a refrigerating system, passing by the introduction of a heating system for the chamber using a thermal belt, until the deposition of a series of Fe/MgO(100) single crystal nanometric film samples. The deposition rates of some materials such as Fe, Py and Cu were investigated through an Atomic Force Microscope (AFM). For the single crystal samples, five of them have the same growth parameters and a thickness of 250Å, except for the temperature, which varies from fifty degrees from one to another, from 100ºC to 300ºC. Three other samples also have the same deposition parameters and a temperature of 300ºC, but with thickness of 62,5Å, 150Å, and 250Å. Magneto-optical Kerr Effect (MOKE) of the magnetic curves measurements and Ferromagnetic Resonance (FMR) were made to in order to study the influence of the temperature and thickness on the sample s magnetic properties. In the present dissertation we discuss such techniques, and the experimental results are interpreted using phenomenological models, by simulation, and discussed from a physical point of view, taking into account the system s free magnetic energy terms. The results show the growth of the cubic anisotropy field (Hac) as the sample s deposition temperature increases, presenting an asymptotic behavior, similar to the characteristic charging curve of a capacitor in a RC circuit. A similar behavior was also observed for the Hac due to the increase in the samples thicknesses. The 250˚A sample, growth at 300°C, presented a Hac field close to the Fe bulk value

Recidiva de câncer labial em pacientes atendidos no hospital DR. Luiz Antônio (Natal-RN) entre 1997-2004

Introduction: Cancer of the lip is very common in tropical countries, being noticeable the squamous cell carcinoma as the main histological type. Objective: Evaluate the socialdemographic profile, habits, occupation, clinical characteristics of the cancer lesions and the aftermath of treatment of the patients treated on the Luiz Antônio Hospital (Natal-RN). Design: Retrospective cohort. Methods: We analyzed 181 medical records of patients from the Luiz Antônio Cancer Hospital (Natal-RN) in the period between 1997 and 2004. The statistic evaluation of time between the diagnosis and the relapse or the cure of the patient were done through the Kaplan-Meier method and the comparison of survivor functions were done through the Log-rank test. Later, was estimated the proportional risk model of Cox. Results: The study population were composed by 69,1% males, 95,2% unlettered, the mean age of 66,5 years, 89,0% of smokers and 64,1% had an occupation involving sun exposure. In regard to the clinical characteristics, most lesions were in the lower lip (77,9%), the size of the tumor was smaller than 2 cm (51,8%), 92,6% had localized lesions. Were verified 16,3% of local relapse and 13% of regional. Almost the totally of the cases corresponded to squamous cell carcinoma (97,2%). We observed smaller accumulated probability of not occurrence of local relapse when the base and borders were free of lesions (p=0,041), as well as a smaller probability of regional relapse when the sort of treatment was surgery, associated with other therapeutics modalities (p=0,001). The patients with advanced pathologic stage (p=0,016), treated with surgery associated with other therapeutics modalities (p=0,001) and diameter above 4cm (p=0,019) presented a bigger possibility of any kind of relapse. The multivariable analysis pointed the complex treatments (surgery plus other therapeutics modalities) as a predictor variable for occurrence of new local lesions (p=0,001) and total (p=0,046), besides the age above 70 years to the regional relapse (p=0,050). Conclusion: Cancer of the lip occur in the lower lip, in males, smokers and individuals exposed to Sun light. The relapse was frequent, even being localized and without great consequences to the patient s health. The probability of relapse is related to the size and borders of the lesion and to the histological exam, as well as to the patient s age and complexity of the treatment chosen

Estimação de parâmetros genéticos para resistência à infecção por IMNV em camarões Litopenaeus vannamei por meio de análise de sobrevivência

The main specie of marine shrimp raised at Brazil and in the world is Litopenaeus vannamei, which had arrived in Brazil in the `80s. However, the entry of infectious myonecrosis virus (IMNV), causing the infectious myonecrosis disease in marine shrimps, brought economic losses to the national shrimp farming, with up to 70% of mortality in the shrimp production. In this way, the objective was to evaluate the survival of shrimps Litopenaeus vannamei infected with IMNV using the non parametric estimator of Kaplan-Meier and a model of frailty for grouped data. It were conducted three tests of viral challenges lasting 20 days each, at different periods of the year, keeping the parameters of pH, temperature, oxygen and ammonia monitored daily. It was evaluated 60 full-sib families of L. vannamei infected by IMNV in each viral challenge. The confirmation of the infection by IMNV was performed using the technique of PCR in real time through Sybr Green dye. Using the Kaplan-Meier estimator it was possible to detect significant differences (p <0.0001) between the survival curves of families and tanks and also in the joint analysis between viral challenges. It were estimated in each challenge, genetic parameters such as genetic value of family, it`s respective rate risk (frailty), and heritability in the logarithmic scale through the frailty model for grouped data. The heritability estimates were respectively 0.59; 0.36; and 0.59 in the viral challenges 1; 2; and 3, and it was also possible to identify families that have lower and higher rates of risk for the disease. These results can be used for selecting families more resistant to the IMNV infection and to include characteristic of disease resistance in L. vannamei into the genetic improvement programs

Avaliação genética da eficiência reprodutiva em vacas pardo-suíças por meio da análise de sobrevivência

Among the traits of economic importance to dairy cattle livestock those related to sexual precocity and longevity of the herd are essential to the success of the activity, because the stayability time of a cow in a herd is determined by their productive and reproductive lives. In Brazil, there are few studies about the reproductive efficiency of Swiss-Brown cows and no study was found using the methodology of survival analysis applied to this breed. Thus, in the first chapter of this study, the age at first calving from Swiss-Brown heifers was analyzed as the time until the event by the nonparametric method of Kaplan-Meier and the gamma shared frailty model, under the survival analysis methodology. Survival and hazard rate curves associated with this event were estimated and identified the influence of covariates on such time. The mean and median times at the first calving were 987.77 and 1,003 days, respectively, and significant covariates by the Log-Rank test, through Kaplan-Meier analysis, were birth season, calving year, sire (cow s father) and calving season. In the analysis by frailty model, the breeding values and the frailties of the sires (fathers) for the calving were predicted modeling the risk function of each cow as a function of the birth season as fixed covariate and sire as random covariate. The frailty followed the gamma distribution. Sires with high and positive breeding values possess high frailties, what means shorter survival time of their daughters to the event, i.e., reduction in the age at first calving of them. The second chapter aimed to evaluate the longevity of dairy cows using the nonparametric Kaplan-Meier and the Cox and Weibull proportional hazards models. It were simulated 10,000 records of the longevity trait from Brown-Swiss cows involving their respective times until the occurrence of five consecutive calvings (event), considered here as typical of a long-lived cow. The covariates considered in the database were age at first calving, herd and sire (cow s father). All covariates had influence on the longevity of cows by Log-Rank and Wilcoxon tests. The mean and median times to the occurrence of the event were 2,436.285 and 2,437 days, respectively. Sires that have higher breeding values also have a greater risk of that their daughters reach the five consecutive calvings until 84 months

Uma medida de calor específico sem calorímetro

Várias técnicas têm sido desenvolvidas para se obter o calor específico de sólidos e líquidos, incluindo a construção de experimentos de baixo custo para o ensino médio. Neste trabalho propomos uma maneira simples de se obter o calor específico de sólidos e líquidos. Por meio de curvas de calibração de resfriamento podemos estimar graficamente a perda de calor do sistema para sua vizinhança, e medir o calor específico do alumínio. Esta aproximação permite introduzir uma discussão sobre o processo dinâmico da troca de calor entre dos corpos.

Comportamento plástico do aço inoxidável austenítico em baixa temperatura

Ensaios de tração uniaxiais foram empregados para deformar aços inoxidáveis austeníticos do tipo 304, em diferentes temperaturas abaixo da ambiente (de 77 K a 300 K). A relação entre a estabilidade da austenita e o encruamento, em função da temperatura de teste, é discutida quanto à transformação martensítica induzida por deformação e ao deslizamento de discordâncias na austenita. em curvas tensão-deformação que assumem a equação de Ludwik sigma = sigmao + képsilonn, na qual sigma é a tensão verdadeira e e a elongação plástica verdadeira, um modo conveniente para analisar o encruamento é por meio do diagrama log dsigma / dépsilon versus log épsilon. O aspecto significativo é a variação da taxa de encruamento dsigma / dépsilon com a elongação plástica verdadeira nas diferentes temperaturas. As mudanças no comportamento do encruamento motivando até três estágios de deformação são associadas a diferentes processos microestruturais. A transformação martensítica pode ser considerada como um processo de deformação que compete com o processo usual de deslizamento. A investigação desses estágios, na região plástica, produz uma referência qualitativa de como diferentes fatores, tais como o grau de deformação, temperatura e composição química da austenita, afetam a transformação austenita-martensita.

Efeito do alerta e valência emocional nos componentes de lembrança e familiaridade da memória episódica

The episodic memory system allows us to retrieve information about events, including its contextual aspects. It has been suggested that episodic memory is composed by two independent components: recollection and familiarity. Recollection is related to the vivid e detailed retrieval of item and contextual information, while familiarity is the capability to recognize items previously seen as familiars. Despite the fact that emotion is one of the most influent process on memory, only a few studies have investigated its effect on recollection and familiarity. Another limitation of studies about the effect of emotion on memory is that the majority of them have not adequately considered the differential effects of arousal and positive/negative valence. The main purpose of the current work is to investigate the independent effect of emotional valence and arousal on recollection and familiarity, as well as to test some hypothesis that have been suggested about the effect of emotion on episodic memory. The participants of the research performed a recognition task for three lists of emotional pictures: high arousal negative, high arousal positive and low arousal positive. At the test session, participants also rated the confidence level of their responses. The confidence ratings were used to plot ROC curves and estimate the contributions of recollection and familiarity of recognition performance. As the main results, we found that negative valence enhanced the component of recollection without any effect on familiarity or recognition accuracy. Arousal did not affect recognition performance or their components, but high arousal was associated with a higher proportion of false memories. This work highlight the importance of to consider both the emotional dimensions and episodic memory components in the study of emotion effect on episodic memory, since they interact in complex and independent way

Esquemas alternativos para o passo de parametrização do método da continuação baseados em parâmetros físicos

O método de fluxo de carga convencional é considerado inadequado para se obter o ponto de máximo carregamento (PMC) de sistemas de potência, devido à singularidade da matriz Jacobiana neste ponto. Os métodos da continuação são ferramentas eficientes para a solução deste tipo de problema, visto que técnicas de parametrização podem ser utilizadas para evitar a singularidade da matriz Jacobiana. Neste trabalho, novas opções para a etapa de parametrização do método da continuação são apresentadas. Mostra-se que variáveis com claro significado físico podem ser utilizadas na etapa de parametrização. As seguintes variáveis foram testadas: perda total de potência ativa e reativa, potência ativa e reativa na barra de referência, potência reativa das barras de geração, e as perdas de potência ativa e reativa nas linhas de transmissão (LT). Além de facilitar a implementação computacional do método de continuação, as técnicas de parametrização apresentadas simplificam a definição matemática e o entendimento do método por parte de engenheiros de potência, visto que os métodos de continuação existentes na literatura sempre utilizam técnicas de parametrização complexas, e de interpretação puramente geométrica. Resultados obtidos com a nova metodologia para os sistemas testes do IEEE (14, 30, 57 e 118 barras) mostram que as características de convergência do método de fluxo de carga convencional são melhoradas na região do PMC. Além disso, durante o traçado das curvas PV, as diversas técnicas de parametrização podem ser comutadas entre si possibilitando o cálculo de todos os pontos da curva com um número reduzido de iterações. Diversos testes são realizados para proporcionar a comparação do desempenho dos esquemas de parametrização propostos.

Técnica de parametrização geométrica para o fluxo de carga continuado baseado nas variáveis tensão nodal e fator de carregamento

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação do ponto de máximo carregamento de sistemas de potência utilizando o fluxo de carga desacoplado rápido parametrizado

Os métodos de fluxo de carga por Newton-Raphson e fluxo de carga desacoplado rápido convencionais são considerados inadequados para a obtenção do ponto de máximo carregamento de sistemas de potência, devido à problemas de mal-condicionamento neste ponto crítico e na sua vizinhança. Neste ponto a matriz Jacobiana do método de Newton-Raphson torna-se singular e considera-se que não são mais válidas as hipóteses de desacoplamento P-V e Q-teta utilizadas para a formulação do método fluxo de carga desacoplado rápido. No entanto, mostra-se neste trabalho, que com pequenas modificações, as versões XB e BX do fluxo de carga desacoplado rápido tornam-se adequadas para a obtenção do ponto de máximo carregamento. Estas novas versões modificadas são comparadas entre si com o intuito de explicitar suas características, assim como da influência da atuação dos limites de geração de potência reativa e de tap's de transformadores. Os resultados obtidos para os sistemas testes do IEEE (14, 30, 57 e 118 barras) mostram que as características de convergência das versões originais são preservadas. Além disso, durante o traçado das curvas PV, os diversos métodos podem ser comutados entre si possibilitando o cálculo de todos os pontos da curva com um número reduzido de iterações.

Fluxo de carga continuado utilizando estratégia de parametrização geométrica baseada em parâmetros físicos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo do comportamento térmico e da luminescência de filmes de quitosana com os íons Eu3+ e Tb3+

Films of chitosan with trivalent lanthanides ions Eu3+ and Tb3+ were respectively prepared in the ratio of 3:1 m/m (chitosan: lanthanide) and 6:1 m/m (chitosan: lanthanide). There were no formations of films in a ratio of 1:1 m/m (chitosan: lanthanides). The films of chitosan with the Tb3+ ion have the same transparent appearance than the pure chitosan films. The film of chitosan with Eu3+ ion has a muddy appearance. These films present good resistance to tear. The appearance of the compounds prepared in ratio 1:1m/m is a white powder. The films and compounds of chitosan were characterized by Elementary Analysis (CHN), Thermal Analysis (TG/DTG) and Spectroscopy of Luminescence. The CHN analysis was made only for compounds prepared in ratio 1:1m/m, suggesting that these compounds possess the formula QUILn.6H2O, where QUI = Chitosan and Ln = Lanthanide. The results of the curves TG/DTG indicated that there are strong interactions between Eu3+ or Tb3+ and chitosan, causing a lesser lost of mass in the films. The luminescence analysis showed that the films of chitosan with the ions Eu3+ and Tb3+ present emissions in the region of the visible one, with bands of the chitosan and of the Eu3+ ion. The luminescence analysis of the compounds of chitosan with the Eu3+ and Tb3+ ions suggest that the chitosan does not transfer into energy to the ions lanthanides, however the chemical neighborhood around of the ion lanthanides breaks the selection rules and, conseqüently the 4f-4f transitions of the lanthanide ions are observed

Reavaliação da eficiência de óleo de coco saponificado e de sua microemulsão como inibidores de corrosão em uma célula eletroquímica

An interesting development in surfactants science and technology is their application as corrosion inhibitors, since they act as protective films over anodic and cathodic surfaces. This work aims to investigate the efficiency of saponified coconut oil (SCO) as corrosion inhibitor and of microemulsified system (SCO + butanol + kerosene oil + distilled water), in saline medium, using an adapted instrumented cell, via techniques involving linear polarization resistance (LPR) and mass loss coupons (MLC). For this, curves of efficiency versus SCO concentration (ranging between 0 and 75 ppm) have been constructed. According to the obtained results, the following efficiency levels were reached with OCS: 98% at a 75 ppm concentration via the LPR method and 95% at 75 ppm via the MLC method. The microemulsified system, for a concentration of 15 ppm of SCO, obtained maximum inhibition of 97% (LPR) and 93% (MLC). These data indicate that it is possible to optimize the use of SCO in similar applications. Previous works have demonstrated that maximal efficiencies below 90% are attained, typically 65% as free molecules and 77% in microemulsified medium, via the LPR method in a different type of cell. Therefore, it can be concluded that the adapted instrumented cell (in those used methods) showed to be an important tool in this kind of study and the SCO was shown effective in the inhibition of the metal

Estudo da corrosão no aço carbono 1020 protegido com óleo de coco saponificado: análise físico-química do comportamento químico do tensoativo

Corrosion inhibitors in solution are utilized to minimize processes from corrosion in steel. Of the present dissertation was evaluated the efficiency by inhibition from the surfactant saponified coconut oil (OCS) in the carbon steel 1020 through in linear polarization electrochemistry technique, well as, studied the process from adsorption through from the isotherms from Langmuir, Frumkin and Temkin. The corrosion current was determined through in Tafel extrapolation from the curves in the polarization, and then, was calculated the efficiency in the inhibitor to each concentration and temperature. Were studied four concentrations (12,5 ppm, 25 ppm, 50 ppm, and 75 ppm) in the inhibitor OCS and one in the NaCl salt (10.000 ppm) in six temperatures (301 K, 308 K, 313 K, 318 K, 323 K, and 328 K) in triplicate. By the results obtained observed that the technique applied can evaluated with rapidity and efficiency corrosion inhibitors. In relation to the isotherms, the than best appropriated was the in Langmuir and in the concentrations studied, the that obtained the best efficiency was the concentration of 75 ppm