Efeito da degradação ambiental nas propriedades de cisalhamento de compósitos PPS/fibra de carbono

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação do comportamento em fadiga de juntas estruturais de ligas de Al2024T3 coladas com adesivo epóxi

Ligas de alumínio são extensamente usadas em partes aeronáuticas devido às boas propriedades mecânicas e baixa densidade. Estas partes devem ser unidas para formar conjuntos maiores. Uma junta estrutural é definida como um segmento de estrutura que provê um meio de transferir carga de um elemento estrutural para outro. A maioria das juntas aeronáuticas é mecanicamente fixada com múltiplos prendedores (parafusos ou rebites). Estas juntas apresentam uma alta concentração de tensões ao redor do prendedor, porque a transferência de carga entre elementos da junta acontece em uma fração da área disponível. Por outro lado, as cargas aplicadas em juntas adesivas são distribuídas sobre toda a área colada e reduz os pontos de concentração de tensão. Juntas são a fonte mais comum de falhas estruturais em aeronaves e quase todos os reparos envolvem juntas. Portanto, é importante entender todos os aspectos de projeto e análise de juntas. O objetivo deste trabalho é comparar estaticamente juntas estruturais de ligas de Al2024-T3 em três condições: juntas mecanicamente rebitadas, juntas coladas e uma configuração híbrida rebitada e colada. Foi usada a norma NASM 1312-4 para confecção dos corpos-de-prova. Além disso, foram conduzidos testes de fadiga, sob amplitude de carregamento constante e razão de tensão igual a 0,1 para avaliar a eficiência dos elementos estruturais durante sua vida em serviço. Os resultados mostraram que a configuração híbrida apresenta maior resistência estática e uma vida em fadiga superior à configuração colada.

Monitoramento de 24 horas do desempenho de reator aeróbio de leito fluidizado trifásico na remoção de amônio num sistema de recirculação para produção de tilápia

O objetivo deste trabalho foi monitorar o desempenho de remoção de nitrogênio amoniacal no tratamento das águas residuárias da produção intensiva de tilápia nilótica em sistema com recirculação de água. O sistema foi constituído por um sedimentador convencional e um reator aeróbio de leito fluidizado trifásico com circulação, operados com tempos de detenção hidráulica de 176.4 e 11.9 minutos respectivamente. O meio suporte utilizado no reator foi o carvão ativado granular com densidade aparente de 1.64 g/cm3 e tamanho efetivo de 0.34 mm; a concentração do meio suporte no reator foi mantida constante em 80 g/L. A eficiência média de remoção do nitrogênio amoniacal total foi de 41.2%. O sistema avaliado é uma alternativa efetiva para o reuso da água em sistemas de recirculação para aqüicultura. Embora a variabilidade das concentrações do nitrogênio amoniacal afluente cujo valor médio foi de 0.136 mg/L, o efluente do reator conservou as características de qualidade da água estáveis, com concentrações médias de nitrogênio amoniacal de 0.079 mg/L e do oxigênio dissolvido de 6.70 mg/L, recomendáveis para a criação dos peixes e nas faixas de valores permitidos pela legislação Brasileira (Resolução CONAMA No. 357 de março 5 de 2005) para lançamento de efluentes finais nos corpos de água receptores.

Agente penitenciário: trabalho no cárcere

Behind the high walls of a prison, there is suffering! Suffering from those who atone to their punishment, from those who work on behalf of an alleged regeneration, suffering that has remained for over two centuries. For those who had their conducts characterized as a crime, many studies have been developed. On the other hand, little is known about the prison servants. This research focused mainly on the identification, from the perspective of the correctional officers from two prisons in different states of Brazil, of the negative influence that their jobs have on them, on the factors that serve as protection, as well as the ones that offer them risk. It was observed that hygiene and security conditions are precarious in both prisons. From the reports, scabies, tuberculosis, hepatitis, H1N1, constant violence, politicization of the working environment, doubled working hours, lack of career planning and salaries emerge as evidence of the place where the bodies who work there are subdued, not taking the differences into account. From the above, and as of the many things that still need to be said about this category, it is reiterated the importance in developing studies about the conditions and the work organization and its implications on the mental health of those workers, who lack of public policies committed to their working realities

Os agentes funerários e a morte: o cuidado presente diante da vida ausente

The present time is marked by the art of escape from death, which has become synonymous with failure, its exposure has become intolerable and the care of the dead body were assigned to third parties who market this practice through services and products that shape the market undertaker. In this context, in which death is an object of study, has arisen funeral officers, as professionals dealing with a dead body, with the pain of relatives and their reactions, often being the first to have contact with the death scene. As professionals in the health area, the morticians also deal with death. The first attempt to prevent the arrival of death, funeral officers already has begun their work routine from there. Death and its surrounding part of their profession. What about those professionals whose work demands as a feared and denied by society? This study aims to understand the intents, meanings and implications for the mortician to deal with death in their daily work in order to focus renewed attention to the care of these professionals. To this end, it was carried out a qualitative research grounded in the theoretical framework of Gadamerian hermeneutics for production and interpretation of narratives. It was used two methodological strategies for data collection: in-depth interview with script and workshop with the use of "scenes". Research participants were nine morticians funeral of two funeral agencies of the city of Natal. It was possible to detect the presence of the social imaginary of interdiction on the theme of death from living with feelings of his presence daily, from the need of respondents to naturalize their contacts with death, a requirement of their office to deal with the difficulties of manipulating body fluids and odors, sometimes in a state of decomposition; allied to wishes to achieve the goal of delivering to family-customers a "embellished" body for the final farewell. Being a mortician, in addition to not being a professional motivation, involves facing difficulties related to heavy routine work, low salaries, unprofitable work materials and equipments, besides having to deal with the social gaze that devalues the profession. In turn, they also deal with the pain coming especially from contact with family members, either when they are targets of these feelings of anger, whether they identify with the pain of the bereaved ones. On the other hand, when the recognition and gratitude of the families occur, they find meaning and beauty in their profession of caring for the dead body. The present study by giving voice to morticians has become possible to understand better their profession, the pain that surrounds and care needs of these workers. Finally, it has argued that the mortician may be recognized as a care professional for the way exercising caution with the dead body and their families.

Adolescentes preocupadas em conquistar um corpo magro: Um estudo sobre discursos produzidos em diários eletrônicos

The concern about a good physical condition is heavily present nowadays, in documentary films about health and in the media, and it is also expressed through the outstanding growth of physical academies, beauty institutes and aesthetic medicine and all kind of aesthetic surgeries. In the western world the body wave is a significant trend, characterized by the great investments in body image. However, what is overlooked is the fact that in parallel trend grows the number of teenagers, especially females, with all kind of problems related to their body image. As adolescence is a moment of transformations, teenagers tend to be more aware of their body image and often neglect food ingestion and try to build their bodies following the images they have from top models and movie stars. The low self-esteem accompanying this sort of experience is an additional problem. Therefore the research aim to analyze discourses regarding the body image produced in world wide web diaries (blogs). The blogs selection was made through the site www.blogs.com.br, which is considered the widest guide of electronic diaries in Brazil. We looked after blogs including the keyword body and from adolescents aged 10 to 19, who showed concern about a slim body. Three blogs were chosen, considering the example criteria. Discourse analysis shows that these teenagers feel unsatisfied with their bodies, searching by all means the thinness presented as a aesthetic paradigm in western societies which often implies neglecting their own health, using appetite inhibitor drugs, restricting or totally abstaining food ingestion for long periods of time, or provoking themselves vomits after ingesting food. These behaviors, together with intense fear of gaining weight, can be characterized as alimentary disorders, related to the body image. As they usually hide this sort of behaviors from family and friends who do not share this concern, the blogs seem to be an easy tool for adolescents to find peers with whom to share common values and ideas and reaffirm their identities and virtual sense of community

Desenvolvimento de uma metodologia para caracterização de amostras de sedimento: Rio Jundiaí RN

The study of sediment in water bodies presents great environmental importance, because of its ability to adsorb the pollutants, they may facilitate the understanding of the history of the current quality of the water system. Depending on how it is done the collection, analysis can show both a recent contamination as old. The detailed characterization of the sediment may reveal details that can understand how each type of pollutant interacts with the material given its composition. In this work it has developed a systematic methodology to characterize samples of sediment, with the aim to understand how a series of metal is distributed in different size fractions of the sediment. This study was conducted in five samples of sediment (P1, P2, P3a, P3B and P3c) collected in Jundiaí river, one of the most important tributaries of the river Potengi in the region of Macaíba, RN. The characterization was made with the samples previously sieved into meshes with different granulometries (+8#, -8+16#, -16+65# - 65+100#,-100+200#,-200+250# and -250#), using the following techniques: Analysis of specific surface area by BET method, determining the levels of organic matter (OM%) and humidity through the gravimetry and Analysis Thermogravimetric (TG), Infrared Spectroscopy in a Fourier transform (FTIR ), Analysis of X ray diffraction (XRD), analysis of heavy metals by optical emission spectrometry with the Argon Plasma (ICP-OES). The analyzed elements were Al, Cd, Cr, Cu, Fe, Mn, Ni, Zn and P. In addition to the techniques of characterization above, was also made the rebuilding of the samples P1, P2 and P3B in relation to the levels of organic matter and concentration of heavy metals. Then, the results of the recomposed samples were compared with those obtained in crude samples, showing great consistency. The gravimetry, used in determining the levels of organic matter, was not considered an appropriate method because the clay minerals present in the sediment samples analyzed fall apart in the same range of temperature (550-600 0C) used in roasting (600 0C). The results also showed the trend of organic matter and heavy metals to focus on the thin fractions, although the largest concentrations of metals are in intermediate fractions

Avaliação da poatencialidade da perlita natural e expandida na adsorção de metais

The contamination by metal ions has been occurring for decades through the introduction of liquid effluent not treated, mainly from industrial activities, rivers and lakes, affecting water quality. For that the effluent can be disposed in water bodies, environmental standards require that they be adequately addressed, so that the concentration of metals does not exceed the limits of standard conditions of release in the receptor. Several methods for wastewater treatment have been reported in the literature, but many of them are high cost and low efficiency. The adsorption process has been used as effective for removal of metal ions. This paper presents studies to evaluate the potential of perlite as an adsorbent for removing metals in model solution. Perlite, in its natural form (NP) and expanded (EP), was characterized by X-ray fluorescence, X-ray diffraction, surface area analysis using nitrogen adsorption (BET method), scanning electron microscopy and Fourier transform infrared spectroscopy. The physical characteristic and chemical composition of the material presented were appropriate for the study of adsorption. Adsorption experiments by the method of finite bath for model solutions of metal ions Cr3+, Cu2+, Mn2+ and Ni2+ were carried out in order to study the effect of pH, mass of the adsorbent and the contact time on removal of ions in solution. The results showed that perlite has good adsorption capacity. The NP has higher adsorption capacity (mg g-1) than the EP. According to the values of the constant of Langmuir qm (mg g-1), the maximum capacity of the monolayer was obtained and in terms of proportion of mass, we found the following order experimental adsorption: Cr3+ (2.194 mg g- 1) > Ni2+ (0.585 mg g-1) > Mn2+ (0.515 mg g-1) > Cu2+ (0.513 mg g-1) and Cr3+ (1.934 mg g-1)> Ni2+ (0.514 mg g-1) > Cu2+ (0.421 mg g-1) > Mn2+ (0.364 mg g-1) on the NP and EP, respectively. The experimental data were best fitted the Langmuir model compared to Freundlich for Cu2+, Mn2+ and Ni2+. However, for the Cr3+, both models fit the experimental data

Comparação da cifose torácica e capacidade funcional de mulheres idosas com e sem osteoporose

A diminuição da densidade mineral óssea das vértebras, própria do processo de envelhecimento e que pode ser agravada pela osteoporose, determina uma diminuição da região anterior dos corpos vertebrais, resultando em compressão e colapso dessas vértebras, com maior estreitamento dos discos e espaços intervertebrais. Essas novas condições interferem no funcionamento normal de órgãos e sistemas do organismo. O objetivo foi avaliar o grau de cifose torácica e a capacidade funcional de mulheres idosas com e sem osteoporose. Foram avaliadas 30 idosas ativas fisicamente, sendo 20 sem osteoporose ( GSO: 65,1± 4,67 anos) e 10 idosas com osteoporose (GCO: 68,6± 6,46anos). Foram avaliados a medida da cifose torácica, teste de caminhada de seis minutos (TC6'), Timed Up and go (TUG) e força dos músculos respiratórios (PImáx e PEmáx). Os dados obtidos foram analisados utilizando o teste t de Student. O nível de significância utilizado foi de 5% (α£ 0,05). Houve diferença significativa entre os grupos sem (GSO) e com osteoporose (GCO) somente no TC6'(GSO: 426,63±46,36 m; GCO: 392,64±36,68 m , α =0,02). As outras variáveis analisadas não apresentaram diferença significativa (Cifose torácica: α = 0,17; TUG: α =0,49; PImax: α =0,45; PEmax: α =0,19). A osteoporose não influenciou o grau de cifose torácica, a força dos músculos respiratórios e mobilidade das idosas. Entretanto, o desempenho no TC6' foi influenciado negativamente pela osteoporose.

Mechanical comparative analysis of three different types of sutures in different dimensions tendons: experimental study

O objetivo da presente investigação experimental foi avaliar o perfil mecânico de três tipos de técnicas de sutura entre tendões de dimensões diferentes. Foram utilizados 21 cães sem raça definida (11machos/10 fêmeas), dos quais foram obtidos os tendões flexor comum dos dedos - t.c. (maior dimensão) e tibial cranial - t.cr. (menor dimensão), de ambos os membros pélvicos. Logo após a obtenção das peças foi realizada sutura, segundo cada tipo de técnica, porém sempre com o mesmo número de pontos. Os tendões utilizados para sutura foram sempre do lado direito e o controle do lado esquerdo (t.cr.). Após a sutura, os corpos de prova foram fixados em garras especialmente desenvolvidas e submetidos a ensaio de tração axial à velocidade de 30mm/minuto. Após o ensaio o programa da máquina forneceu os valores da carga máxima ( na ruptura) e deformação absoluta (mm) e relativa (%), além do diagrama carga-deformação. Os resultados foram submetidos a estudo estatístico pela análise de medidas repetidas no nível de 5% de significância. Não foi constatada diferença estatisticamente significativa nos parâmetros mecânicos avaliados nos três grupos de técnicas de suturas. em relação ao controle (tendão de menos diâmetro contra-lateral), observou-se que a sutura apresenta resistência máxima a tração significativamente menor que o controle e maior deformação.

Análise comparativa das propriedades mecânicas do ligamento da patela e do tendão calcâneo

Com a finalidade de se comparar as propriedades mecânicas do ligamento da patela e do tendão calcâneo foram realizados ensaios de tração em material obtido de 25 cadáveres humanos. A idade dos doadores foi 58 ± 14 anos (33-85), sendo 19 (76%) masculinos e 6 (24%) femininos, 23 brancos (92%) e dois negros (8%). Os materiais foram testados em seus 10 mm centrais, com velocidade de aplicação de carga de 30 mm/min. Foi obtida a área de secção dos corpos de prova para que fossem estudadas as propriedades estruturais e materiais. Foram estudadas as seguintes variáveis: carga máxima (N), tensão(MPa), módulo de elasticidade (MPa), energia (Nm), alongamento absoluto (mm) e específico (%), limite de proporcionalidade (N), além da tensão (MPa) e alongamentos neste ponto. A análise estatística revelou que ambos possuem carga máxima, limite de proporcionalidade e tensão semelhantes (p>0,05). Nas outras variáveis ocorreu diferença significativa (p<0,05) com o tendão calcâneo apresentando valores maiores para energia e alongamento. O módulo de elasticidade, significativamente maior no ligamento da patela (p<0,05), foi a variável que melhor caracterizou a diferença do comportamento mecânico dos dois materiais.

Dinâmica da paisagem na Microbacia do Riacho Cajazeiras no semiárido potiguar

The semi-arid Northeast region are coming through changes since its formation causing changes in the landscape and increased degradation. The economic dynamics which was established at the Potiguar semiarid had for a long time settled in livestock, subsistence agriculture and cotton, however, these economies decline from the year 1970. Thus, the Potiguar spaces are undergoing by a process of space reordering marked by the growth of agricultural activities and the process of urbanization. In the Potiguar western region these changes weaken significantly transform the landscape. In these areas, the process of urbanization and agricultural activities have caused changes in the hinterland landscape changing the natural dynamics of the caatinga biome that has been subject to negative interference with the indiscriminate removal of vegetation. In this case, the specific study area of the watershed of Cajazeiras Creek located in the cities of Pau dos Ferros, Água Nova, Encanto and Rafael Fernandes, changes in the landscape has led to degradation and environmental fragility. From this perspective, the research objective is to assess the dynamics of the landscape of the watershed of Cajazeiras Creek, semiarid region of the state of Rio Grande do Norte, identifying the degrading factors, the most degraded areas and/or susceptible to degradation and environmental fragility. The research investigated the phenomena of light geosystems theory that emphasizes the integration of elements in shaping the landscape. During this reporting period, it was carried out exploratory and bibliographical research, and geoprocessing techniques to assess the social and environmental conditions of the researched area and its environmental fragility. To do so, first, it was made an multitemporal analisis on the basis of the years 1984, 1996 and 2009 demonstrating that the dynamics of use and land cover in the watershed of Cajazeiras Creek showed a significant change in the landscape, especially in the caatinga vegetation. This has been recovering in various areas of the watershed, especially in its upper course in the mountains of Bom Sera, in Encanto city. The analysis showed the need to develop policies and programs for the maintenance, restoration and preservation of the caatinga vegetation of the river network and of water bodies. In addition, it was identified the most degraded areas of the watershed, environmental fragility and potential emerging that take into account the landscape components such as climate, topography, geology, pedology, geomorphology and the use and occupation of the soil in an integrated manner. The results show that the landscape of the watershed has medium and high environmental fragility throughout its area, especially on the banks of the river network provided by the use and occupation of the soil in an inadequate way with the environmental conditions of the watershed

Quilombolas e desenvolvimento sustentável: análise a partir da comunidade Capoeira dos Negros (Macaíba/RN)

Quilombo communities remaining are groups marked by insufficient public assistance and characterized by living in rural and conducting economic activities such as agriculture. The development on a sustainable basis is important to ensure strategies for economic growth and environmental preservation. This work aims to study the remaining Quilombo Capoeira Black community, located in the municipality of Macaíba, Rio Grande do Norte, considering the principles of sustainable development. Attempt to respond to what level such community can be considered sustainable from an analysis of their social practices. The methodological procedures used consisted of a literature review and documentary, questionnaires, conducting semi-structured interviews and direct observation. The final results show that the family farm has characteristics that approximate the principles of sustainable development, including the diversification of labor, food production with less environmental damage and strengthening the rural environment, and indicate that the main economic activities practiced in Capoeira dos Negros community are agriculture, manufacturing of cassava flour and brick manufacturing, which, in turn, are linked to negative environmental impacts, such as sedimentation pond, groundwater contamination, air pollution and soil erosion. What lead to the conclusion that the social practices of the community are not in line with the dimensions of sustainable development. It is hoped that the survey results provide subsidies for development and implementation of public policies

Tessituras poéticas da corporeidade na formação humana do educador infantil

Cette étude a comme sujet principal la formation humaine de l instituteur. L objectif général est d analyser et décrire les conditions créées par les vécus d un atelier corps biographique pour la resignification de la corporéité de l instituteur, fixant les questions suivantes pour l investigation : Quelles sont les implications du vécu de l atelier corps biographique dans la vie des instituteurs ? La recherche a été exposée sur l approche qualitative, suivant les principes de la recherche-action reliée à la méthode des histoires de vie. Pour révéler la beauté et la complexité du processus poïétique de la formation humaine, nous nous sommes servi de la métaphore du "dessus de lit en patchwork" comme opérateur cognitif en attachant les principes de la corporéité fondés sur la Théorie de la complexité (MORIN, 2005), la Théorie autopoïétique (MATURANA ; VARELA, 2001), la Théorie du flux (CSIKSZENTMIHALYI, 1999), les approches de transdisciplinarité (LA TORRE; MORAES, 2008), et d autobiographie (JOSSO, 2004; PINEAU, 2003; PASSEGGI, 2000;), joignant la conception de l éducation comme pratique d autonomie, de liberté, d espoir et de l enchantement (FREIRE, 1996, 1992; ASSMANN, 1995). Nous avons eu comme scène du développement de la recherche, l Unidade Educacional Infantil (UEI), la garderie qui accueille les enfants des fonctionnaires de l Université Fédérale du Rio Grande do Norte. Treise élèves (enfants), des institutrices titulaires, vacataires, boursières ont participé de l'investigation. En conptant sur eux, nous avons développé un atelier corps biographique, dans lequel nous avons réalisé 10 vécus dans la période qui a couvert le deuxième semestre de 2007 jusqu au deuxième semestre de 2008, en manifestant la réflexivité autobiographique, le ludique, la créativité, la sensibilité et la réflexivité du vécu. Nous avons utilisé comme instruments pour la construction des donnés, l observation participante, les propres vécus, le port folio, la technique du jeu de sable et l'enregistrement photographique. L analyse a montré que le vécu de la formation humaine à partir des principes de la corporéité, implique dans un parcours vers soi-même dans lequel émergent les expériences qui nous ont constitués en tant qu êtres existentiels. Pour finaliser, nous avons aperçu les répercussions dans la vie professionnelle et personnelle de ces institutrices, qui comme moi pensaient avoir besoin d exposer leur luminosité intérieure pour que l on la redécouvre. Lors des vécus des tissages, les institutrices se sont montrées impliquées aux moments de jeux, de création, de réalisation, d afection et d action réflexive, dans lesquelles la teneur humaine cachée, a été révélée, en ouvrant les possibilités pour le sentiment du mouvement de naissance de l humanisation intérieure. Pour conclure, le corps joyeux de savoir et de beauté a été révélé, et dans sa rencontre avec soi-même et avec l autre, a pu être auto- recréé

Estudo do comportamento mecânico de estruturas de solo-cimento reforçado com fibras de coco e hastes de bambu

In this work the use of coconut fiber (coir) and bamboo shafts as reinforcement of soil-cement was studied, in order to obtain an alternative material to make stakes for fences in rural properties. The main objective was to study the effect of the addition of reinforcement to the soil-cement matrix. The effect of humidity on the mechanical properties was also analyzed. The soil-cement mortar was composed by a mixture, in equal parts, of soil and river sand, 14% in weight of cement and 10 % in weight of water. As reinforcement, different combinations of (a) coconut fiber with 15 mm mean length (0,3 %, 0,6 % and 1,2 % in weight) and (b) bamboo shafts, also in crescent quantities (2, 4 and 8 shafts per specimen) were used. For each combination 6 specimens were made and these were submitted to three point flexural test after 28 days of cure. In order to evaluate the effect of humidity, 1 specimen from each of the coconut fiber reinforced combination was immersed in water 24 hours prior to flexural test. The results of the tests carried out indicated that the addition of the reinforcement affected negatively the mechanical resistance and, on the other hand, increased the tenacity and the ductility of the material.