Análise da vibração para o controle do funcionamento de um ventilador de um sistema de exaustão

This work has as objective to show the vibrational analysis as a method of predictive maintenance as an auxiliar procedure in the fail detection in equipments, most specifically in the rotative ones, and with that help the maintenance team to have conditions to foresee the right time to do the swap of the components of the systems, what would lead to failures. Knowing the exact moment the resources of people and money can be focused in the critic operations to the plant. This technic has been already studied for more then 30 years and was widely used in this work, not only as an equipment condition verification method, but also, after the equipment replacement, was used to prove that the new fan was operating under the best work conditions and with that maintenance could return to contol the vibration level of the equipment, not being necessary any kind of intervention

Controle de qualidade em radioterapia: dosimetria de fótons em acelerador linear – Mevatron MXT

The treatment of a tumor with ionizing radiation is an ongoing process with well differentiated stages. These ones include the tumor diagnosis and location, the decision on the treatment strategy, the absorbed dose planning and calculation, the treatment administration, the absorbed dose verification and the evaluation of results in short and long terms. The quality of a radiotherapy procedure is closely linked to factors that may be classified as clinical, such as the diagnosis, the tumor location, the treatment strategy chosen and the continuous treatment reassessment; dosimetric or physical, such as the uncertainty in the dose calculation, its optimization and verification, the suitability of the equipment to provide a radiation beam consistent with the treatment planning; finally, others which are related to the practical application of radiotherapy treatment and the handling of the patient. In order to analyze the radiotherapy quality, one should realize that the three aspects (medical, physical or dosimetric and practical application) should be considered in a combined way. This means that numerous actions of the radiotherapists, medical physicists and technicians in radiotherapy should be held jointly and their knowledge level will significantly affect the treatment quality. In this study, the main physical parameters used in dosimetry are defined as well as determined experimentally for a linear accelerator Mevatron - MXT. With this, it is intended to provide recommendations for the physical aspects of Quality Assurance (QA) in the radiotherapy treatments, and these will usually be applied by professionals in Medical Physics. In addition to these instructions, it is recommended that additional texts are prepared to address in detail the clinical aspects of the treatments QA

Melhoria do processo de reparo por meio da redução de Lead Time em uma empresa de som automotivo

The constant search for improvement and survival of the companies makes essential the utilization of cost reduction strategies and resources optimization. This study had as its objective the utilization of Lean Manufacturing tools for the repair process lead time reduction, in a car audio manufacturer. Performing an action research, the major problems were studied, such as the potential causes and the possible improvement activities, using the DMAIC methodology. An action plan was developed for all involved processes and, as a result, the objective was reached by making a direct impact on the customers’ satisfaction and adding a competitive differential for the company

Controle e caos na formação de moléculas com pulso de laser

We investigate the formation of molecules under the action of external field acting during the atomic collision. To describe this process, the collision of atomic pairs, we use the Morse oscillator model driven The study was developed from the standpoint of classical mechanics by analyzing the sensitivity of the system with respect to initial conditions, the verification of chaotic dynamics associated with the process of formation of molecules with laser and analysis of system dynamics and the likelihood of photoassociation in response to the external field parameters

Mapeamento do processo de originação de etanol em uma empresa do setor de distribuição de combustíveis

The market segment of fuel distribution composes an important role in the development of Brazil’s industry and economy. However, it is a sector with intense competitiveness, especially in relation to ethanol. The search for competitive advantage and greater strength to the business are, therefore, of high relevance in this context, in which the concepts of Business Process Management has become more visible. Process Mapping, one of these concepts, has proven “TO BE”a strategic tool for companies which believe in flattening the structure and in the potential benefits that the improvement of its processes can provide. Thus, this work aims to map the process of Ethanol Origination of a company engaged in the distribution of this and other fuel products, and other niche markets. It was understood and designed the macro-process aforementioned and identified failures in subprocess related to it. After applying the method to select priority problems, using risk assessment criteria, five subprocess were identified to receive special action, which consisted in seeking improvements with those involved in the process, in representing its current and ideal models and in defining each department’s responsibilities for the activities in the subprocess proposed form. Thus, it is expected to mitigate mainly two negative effects found in the business: employee’s work overload and company's financial exposure

Identificação e análise da relação entre a utilização de construtos da qualidade e o desempenho e competitividade organizacional

A growing number of companies is adopting quality management systems to achieve better performance and remain competitive in the market. These systems, however, can prove quite complex because they involve different practices and factors. This paper seeks to identify and analyze how each of these factors and practices, defined as quality constructs, influence the performance and competitiveness in the organizational environment and thus contribute to the strategic decisions in the area of quality. To achieve that, a survey was conducted with industrial companies located in the state of São Paulo, and the data was analyzed by a structural equation software. As a result, it was observed that the constructs Customer Focus and Human Resources are the most influent for the competitive criteria of a company, while the constructs Supplier development and Customer Focus exert greater impact on performance

Coleta de dados, modelagem e controle de qualidade do sistema de planejamento pinnacle3

Qualidade na coleta de dados do feixe de radiação, modelagem por meio do sistema de planejamento de tratamento (SPT) e controle da qualidade do processo envolvido são cruciais à fidedignidade do serviço de radioterapia de forma a contribuir à eficácia do tratamento e segurança do principal ente envolvido no final de toda essa sistemática, o paciente. Para isso foi proposto nesse presente trabalho a coleta de dados do feixe de raios-x de 6MV seguido da introdução desses dados ao SPT para processo de modelagem computacional que teve agregado, a todo esses processos, o controle da qualidade segundo critérios de aceitação

Fatores facilitadores e restritivos no processo de gestão de franquias sob o ponto de vista do franqueado: um estudo multicasos no setor de alimentação

The present study sought to identify which are the facilitators and restrictive in the creation and management of franchises from the point of view of process factors franchisees. For this, we first proposed to critically analyze its creation and management.The specific objectives of this work are: a) to understand in the light of the theory , the basic requirements for creating franchises b ) identify, from the literature review , facilitators and restrictive factors in the process of franchise management , c) develop a survey tool to critically analyze the processes of creating and managing a franchise from the point of view of the franchisee , and d ) to review the process of creating and managing franchises , from the perspective of four franchised food services in the municipalities of Ribeirão Preto and Sao Jose do Rio Preto - SP . A descriptive qualitative work, which found the most important features about the franchises, through a study of 4 franchises in the food industry of São Paulo was performed. To complete the survey was conducted a semi-structured interview, containing questions regarding the main elements of a business: creating, planning, organization, direction and control. It was found that franchising is a business model with controversies. There are people who deal well with the system and that through him realize dreams such as owning their own business. Others need to think many times before embarking in business since the entrepreneurship factor can be so intense that it hinders the acceptance of norms and duties to the system. This causes some factors such as communication, measurement of outcomes, implementation plan and among others are considered restrictive or facilitators in the process of strategy management of franchises

Gestão ambiental aplicada a prevenção, controle e recuperação de erosão linear acelerada no município de Ipeúna-SP

The erosion is a natural process of detachment, transport and deposition of soil and rock particles from one place to another. Human activities with no previous planning may accelerate this process, causing several damages to the environment and to society. In order to control the acceleration of these erosion processes caused by humans, prevention and improvement initiatives emerge. Regarding works which interfere directly in some of the natural resources, these initiatives must respect the intrinsic physical properties of the area of interest, if they aim to obtain effective results. Based on this scenario, this work proposes a few methods of accelerated linear erosion prevention, control and recovery in a specific area of the municipal district of Ipeúna (SP). For that matter, this study is based on a method of physiographic compartmentalization of the area, considering and integrating soil, relief, geology and the use and land cover properties of the study area. Plus, a flowchart with general orientations regarding management of eroded areas was produced, focused on the control and recovery of linear erosion. The result demonstrates the importance of careful erosion control, respecting the physical properties of each physiographic unit. The vegetative and mechanical conservationists methods, and the discipline of water flow, have found wide applicability in the study area.

Processo de fabricação de tarugos pelo método HotTop de ligas de alumínio da série 6XXX e as não conformidades desse processamento

The goal of this work is to report some problems that occur in the in the production of aluminum billets (series 6XXX) produced by the hot top process in the Alcoa aluminum Inc. The aluminum fabrication process is described from its first stage, since the mining until the reduction, smelting and treatment of the metal. One of the plant’s final product, are billets for clients that produce profiles by extrusion. The product’s final quality highly depends on the whole production process. Therefore it’s necessary to use good practices in the treatment of the metal, follow up its fabrication and control its thermal treatment, in order to meet the required standards to satisfy the clients. The billet’s production method and its variables will be detailed through temperature and casting speed, cone of water flow, cooling rate, duration of thermal treatment, degassing and metal “in line “filtering, in other words when it’s still found in its liquid state. The non-conformities of the process were studied by metallographic analysis, both macrostutural and microstructural that will be described and discussed in this work

Identificação de causas especiais no processo que aumentam a ocorrência de poro na solda de tubos de aço: aplicação etapas definir, medir e analisar do DMAIC

This work covers the methodology Six Sigma with the application of the steps Define, Measure and Analyze a company of steel tubes, with the objective of identify special causes in the process that drives the creation of the pore defect in the solder. It is highlighted the fact that this work is the base of an continuous upgrade project that aims in eliminating the occurrence of this defect. The motivation is given to the necessity of improving the productivity of the factory, considering that the defect occurs at random and your causes are unknown. This way, it was defined that the problem to analyze, measured the capability of the process in DPMO and analyzed with the aid of graph by attribute P. The results show the process that present special cases, as well as the process considered ideal, This way it was stated that in this work, the processes destabilized and the controlled, allowing a comparison of the characteristics for the elaboration of concise action plans to eliminate the defect. The project must follow the steps Upgrade and control the methodology Six Sigma, in order to ensure success in his execution, aiming to amplify the competitive edge of the business

Gestão de Estoques: análise e melhoria do processo de inventário físico em uma indústria siderúrgica

Accuracy in physical inventory process is essential to develop anefficient inventorycontrol. This ensures the availability of products and ensure that the information contained in the information systems areinaccordancewith the reality of inventories. The inventory management policies of the company aim ofthis study established that all the materials in their inventory must becounted, which is proving a challenge. Therefore, the aim of thiswork is to identify the critical inventories and analyze them, seeking flaws and possible improvements in the inventory count process. For this, we used the tools of quality management, such as Pareto and Cause and Effect Diagrams in an action research. The results show that the stocks of finished products are critical in volume and can be hampered by a lack of training and personnel trained in performing the process, as well as limitations in ERP used. With the actions taken against these problems, we could notice an improvement in the process, because the data collection and processing of data has become easier, besides the occurrence of errors decreased. In addition, there was an acceleration in meeting targets compared to the previous period

Método de Taguchi aplicado a um processo de corte por fusão de um tecido sintético

A company must have full knowledge and control of its operations so as to meet the market requirements and meet their production goals. Thus this paper uses the Taguchi method to extend the operational control of a cutting process by fusion of a synthetic fabric in the longitudinal direction. For process analysis and tracking of possible causes of the problem techniques of Production Engineering as the cause and effect diagram, also known as Ishikawa diagram, and design of experiments were used, the last one was applied to the design techniques of Taguchi. Finally the preparation method of understanding and design of experiment was due to the use of the software MINITAB v15 ®, which showed that the speed of rolling the fabric after cutting is crucial for controlling the entire operation

Controle de qualidade e qualificação de fornecedores de matérias primas utilizadas em uma farmácia de manipulação

Este trabalho apresenta uma proposta de qualificação de fornecedores de matérias primas para uma farmácia na cidade de Araraquara, estado de São Paulo. A qualificação de fornecedores é um processo de extrema importância no que diz respeito ao produto acabado e, para que tenha qualidade, essa qualidade deve vir desde as matérias primas que o compõem. A RDC nº 67 de 8 de outubro de 2007 diz que as farmácias devem adquirir matérias primas apenas de fornecedores qualificados. Para o processo de qualificação, a mesma RDC diz que devem ser feitas auditorias e levantamentos de dados dos fornecedores, bem como o controle de qualidade das matérias primas fornecidas. Foram escolhidas quatro matérias primas utilizadas pela farmácia de três fornecedores diferentes. O processo começou com o envio de questionários avaliativos, onde cada fornecedor deveria colocar as informações solicitadas. O passo seguinte é o controle de qualidade das matérias primas. A partir dos dados dos questionários e dos resultados do controle de qualidade, acrescidos de outros fatores como prazo de entrega, compõe-se o Índice de Qualificação do Fornecedor (IQF), que é como uma “nota” que o fornecedor recebe e, através desse índice, pode ser DESQUALIFICADO, QUALIFICADO ou ainda CERTIFICADO. A certificação ocorre após a auditoria do estabelecimento do fornecedor e também entra na composição do IQF. Após o processo de qualificação dos três fornecedores, foi elaborado um Procedimento Operacional Padrão (POP) com todas as etapas que devem ser feitas para a qualificação...

Melhoria da qualidade de um processo de usinagem utilizando as técnicas de avaliação de Taguchi

Delivering to the customers a product or service with the expected quality associated to the huge competitiveness that exists in the market nowadays, has been making organizations increasingly focus on quality planning using techniques which are directed towards the continuous improvement process and production optimization. Thus, this paper aims to improve a machining process using the techniques of experimental design to the optimization and this also includes the analysis of the measurement system. For this purpose, the alloy Nimonic 80A, a nickel base superalloy, was used in the process due to its widespread use for high temperatures, applying this study the robust method proposed by Genichi Taguchi, determining the influence of the factors considered input variables, cutting speed, feed rate, depth of cut, type of tool, lubrication, and material hardness, in the output or response variable, surface roughness, concluding with the use of Taguchi orthogonal array L16 and by analysis of ANOVA that the factor feed rate is significant and offers greater effect on the response variable studied, should be set to 0,12mm/rev. Moreover, the factor type of tool has more influence on the process when compared to other factors, being CP250 the one more suitable to the process. Lastly, the interaction feed rate x cutting speed provides greater significance in the process regarding to surface roughness variable, being the best match between them 0,12mm/rev to the feed rate and 90m/min to the cutting speed. In order to evaluate the measurement system, it was applied the repeatability and reproducibility method (R&R), through which we saw that the system needs improvement (R & R = 88.04% >>> 30%) as the value found in the study was well above compared to the one that classifies the system as inappropriate