Experimental investigation of antenna selection and transmit beamforming for capacity enhancement in 3×3 MIMO-enabled radio-over-fiber DAS

This paper examines the impact of two simple precoding schemes on the capacity of 3 × 3 MIMO-enabled radio-over-fiber (RoF) distributed antenna systems (DAS) with excess transmit antennas. Specifically, phase-shift-only transmit beamforming and antenna selection are compared. It is found that for two typical indoor propagation scenarios, both strategies offer double the capacity gain that non-precoding MIMO DAS offers over traditional MIMO collocated antenna systems (CAS), with capacity improvements of 3.2-4.2 bit/s/Hz. Further, antenna selection shows similar performance to phase-only beamforming, differing by <0.5% and offering median capacities of 94 bit/s/Hz and 82 bit/s/Hz in the two propagation scenarios respectively. Because optical DASs enable precise, centralized control of remote antennas, they are well suited for implementing these beamforming schemes. Antenna selection, in particular, is a simple and effective means of increasing MIMO DAS capacity. © 2013 IEEE.

Low temperature heat capacity and thermal stability of nanocrystalline nickel

The heat capacity (C-p) of nanocrystalline nickel (nc-Ni, 40 mn crystallite size) has been measured over the temperature range of 78-370 K with a high-resolution automated adiabatic calorimeter. The measured results are compared with the C-p values of the corresponding coarse-grained crystal, and an enhancement of heat capacity of the nanocrystalline nickel was observed to be 2-4% in the temperature range between 100 and 370 K. The thermal stability of the nanocrystalline nickel sample was determined by a differential scanning calorimeter and a thermogravimetric system. The melting point of nc-Ni is the same as that of the corresponding coarse-grained crystalline nickel and the sample is stable at temperature lower than 500 K. (C) 2002 Elsevier Science B.V. All rights reserved.

Heat capacity enhancement and thermodynamic properties of nanostructured amorphous SiO2

The heat capacity of nanostructured amorphous SiO2 (na-SiO2) has been measured by adiabatic calorimetric method over the temperature range 9-354 K. TG and differential scanning calorimeter (DSC) were also employed to determine the thermal stability. Glass transition temperature (T-g) for the two same grain sizes with different specific surface of naSiO(2) samples and one coarse-grained amorphous SiO2 (ca-SiO2) sample were determined to be 1377, 1397 and 1320 K, respectively. The low temperature experimental results show that there are significant heat capacity (C-P) enhancements among na-SiO2 samples and ca-SiO2. Entropy, enthalpy, Gibbs free energy and Debye temperature (theta (D)) were obtained based on the low temperature heat capacity measurement of na-SiO2. The Cp enhancements of na-SiO2 were discussed in terms of configurational and vibrational entropy. (C) 2001 Elsevier Science B.V. All rights reserved.

Changes in innovation styles - comprehensive study of the changes in innovation styles to identify the causes and effects of different influencing factors and capabilities to create a general innovation pattern.

An investigation in innovation management and entrepreneurial management is conducted in this thesis. The aim of the research is to explore changes of innovation styles in the transformation process from a start-up company to a more mature phase of business, to predict in a second step future sustainability and the probability of success. As businesses grow in revenue, corporate size and functional complexity, various triggers, supporters and drivers affect innovation and company's success. In a comprehensive study more than 200 innovative and technology driven companies have been examined and compared to identify patterns in different performance levels. All of them have been founded under the same formal requirements of the Munich Business Plan Competition -a research approach which allowed a unique snapshot that only long-term studies would be able to provide. The general objective was to identify the correlation between different factors, as well as different dimensions, to incremental and radical innovations realised. The 12 hypothesis were formed to prove have been derived from a comprehensive literature review. The relevant academic and practitioner literature on entrepreneurial, innovation, and knowledge management as well as social network theory revealed that the concept of innovation has evolved significantly over the last decade. A review of over 15 innovation models/frameworks contributed to understand what innovation in context means and what the dimensions are. It appears that the complex theories of innovation can be described by the increasing extent of social ingredients in the explanation of innovativeness. Originally based on tangible forms of capital, and on the necessity of pull and technology push, innovation management is today integrated in a larger system. Therefore, two research instruments have been developed to explore the changes in innovations styles. The Innovation Management Audits (IMA Start-up and IMA Mature) provided statements related to product/service development, innovativeness in various typologies, resources for innovations, innovation capabilities in conjunction to knowledge and management, social networks as well as the measurement of outcomes to generate high-quality data for further exploration. In obtaining results the mature companies have been clustered in the performance level low, average and high, while the start-up companies have been kept as one cluster. Firstly, the analysis exposed that knowledge, the process of acquiring knowledge, interorganisational networks and resources for innovations are the most important driving factors for innovation and success. Secondly, the actual change of the innovation style provides new insights about the importance of focusing on sustaining success and innovation ii 16 key areas. Thirdly, a detailed overview of triggers, supporters and drivers for innovation and success for each dimension support decision makers in putting their company in the right direction. Fourthly, a critical review of contemporary strategic management in conjunction to the findings provides recommendation of how to apply well-known management tools. Last but not least, the Munich cluster is analysed providing an estimation of the success probability of the different performance cluster and start-up companies. For the analysis of the probability of success of the newly developed as well as statistically and qualitative validated ICP Model (Innovativeness, Capabilities & Potential) has been developed and applied. While the model was primarily developed to evaluate the probability of success of companies; it has equal application in the situation to measure innovativeness to identify the impact of various strategic initiatives within small or large enterprises. The main findings of the model are that competitor, and customer orientation and acquiring knowledge important for incremental and radical innovation. Formal and interorganisation networks are important to foster innovation but informal networks appear to be detrimental to innovation. The testing of the ICP model h the long term is recommended as one subject of further research. Another is to investigate some of the more intangible aspects of innovation management such as attitude and motivation of mangers. IV

Innovation in Ireland's 'high-technology' businesses: the roles of interaction and proximity

This thesis explores the drivers of innovation in Irish high-technology businesses and estimates, in particular, the relative importance of interaction with external businesses and other organisations as a source of knowledge for innovation at the business-level. The thesis also examines the extent to which interaction for innovation in these businesses occurs on a local or regional basis. The study uses original survey data of 184 businesses in the Chemical and Pharmaceutical, Information and Communications Technology and Engineering and Electronic Devices sectors. The study considers both product and process innovation at the level of the business and develops new measures of innovation output. For the first time in an Irish study, the incidence and frequency of interaction is measured for each of a range of agents, other group companies, suppliers, customers, competitors, academic-based researchers and innovation-supporting agencies. The geographic proximity between the business and each of the most important of each of each category of agent is measured using average one-way driving distance, which is the first time such a measure has been used in an Irish study of innovation. Utilising econometric estimation techniques, it is found that interaction with customers, suppliers and innovation-supporting agencies is positively associated with innovation in Irish high-technology businesses. Surprisingly, however, interaction with academic-based researchers is found to have a negative effect on innovation output at the business-level. While interaction generally emerges as a positive influence on business innovation, there is little evidence that this occurs at a local or regional level. Furthermore, there is little support for the presence of localisation economies for high-technology sectors, though some tentative evidence of urbanisation economies. This has important implications for Irish regional, enterprise and innovation policy, which has emphasised the development of clusters of internationally competitive businesses. The thesis brings into question the suitability of a cluster-driven network based approach to business development and competitiveness in an Irish context.

The paradox of openness revisited: Collaborative innovation and patenting by UK innovators

© 2016 The Authors.We revisit the "paradox of openness" in the literature which consists of two conflicting views on the link between patenting and open innovation-the spillover prevention and the organizational openness views. We use the data from the Survey of Innovation and Patent Use and the Community Innovation Survey (CIS6) in the UK to assess the empirical support for the distinct predictions of these theories. We argue that both patenting and external sourcing (openness) are jointly-determined decisions made by firms. Their relationship is contingent upon whether the firms are technically superior to their rivals and lead in the market or not. Leading firms are more vulnerable to unintended knowledge spillovers during collaboration as compared to followers, and consequently, the increase in patenting due to openness is higher for leaders than for followers. We develop a simple framework that allows us to formally derive the empirical implications of this hypothesis and test it by estimating whether the reduced form relationship between patenting and collaboration is stronger for leaders than for followers.

Determining factors of the innovative behavior of cooperatives: an analysis of the case of Castilla y León

Cooperatives have a long historical experience in the Spanish economy and have demonstrated their ability to compete against traditional firms in the market. To maintain this capability, while taking advantage of the competitive advantages associated with their idiosyncrasies as social economy enterprises, they should take into consideration that the economy is increasingly globalized and increasingly knowledge-based, especially with regards to technological content. As a consequence, the innovative capacity appears to be a key aspect in order to be able to challenge competitors. This article characterizes the innovative behavior of cooperatives in the region of Castile and Leon and analyses the internal and external factors affecting their innovative performance, based on data from a survey of 581 cooperatives. The results of the empirical analysis, which is performed by multivariate binary logistic regression on various types of innovation, lead us to identify the size of the organizations, the existence of planning, the R & D activities and the human capital as the main determining factors.

Video games in the classrooms: implications of a disruptive innovation to develop the Multiple Intelligences

The present study aims to identify the framework of personal, organizational and technical variables that contribute to the viability and successful of innovative educational practices with video games within the school context to enhance the multiple intelligences. For this purpose, advantage was taken on the information previously collected through a questionnaire about the views, thoughts and experiences of a group of teachers of childhood and primary education (N=25) who voluntarily participated in a blended training activity from Center of Teachers (CEFIRE) of Valencia, around a community of practice aimed at promoting and advising projects for implementing educational video games in the classroom. The mixed methodology adopted has allowed the following: a) describe the relationship between their degree of development and daily use made of ICT in the classroom, their level of familiarity with video games,  their previous experience to integrate them for educational purposes..., and their participation in projects that focus on game-based learning; b) conduct content analysis of the opinions and thoughts expressed in a forum for teachers on innovation on and methodological strategies adopted reflected in a virtual board; and c) develop a SWOT analysis: Strengths, Weaknesses, Opportunities and Threats inherent in the implementation of experience with video games in the classroom. Among the conclusions, it is highlighted that, even though most did not have specific training or enough technological resources and the planning and implementation of innovation required them a great investment of time, their personal interest, the support given by members of the online community of practice, helped to encourage their activity, along with receptivity, positive attitude and high motivation of students with the experience. These aspects have been crucial to promote successful innovative practices with video games.

Capacity and resource allocation of cooperative MIMO in ad hoc networks

Cooperative MIMO (Multiple Input–Multiple Output) allows multiple nodes share their antennas to emulate antenna arrays and transmit or receive cooperatively. It has the ability to increase the capacity for future wireless communication systems and it is particularly suited for ad hoc networks. In this study, based on the transmission procedure of a typical cooperative MIMO system, we first analyze the capacity of single-hop cooperative MIMO systems, and then we derive the optimal resource allocation strategy to maximize the end-to-end capacity in multi-hop cooperative MIMO systems. The study shows three implications. First, only when the intra-cluster channel is better than the inter-cluster channel, cooperative MIMO results in a capacity increment. Second, for a given scenario there is an optimal number of cooperative nodes. For instance, in our study an optimal deployment of three cooperative nodes achieve a capacity increment of 2 bps/Hz when compared with direct transmission. Third, an optimal resource allocation strategy plays a significant role in maximizing end-to-end capacity in multi-hop cooperative MIMO systems. Numerical results show that when optimal resource allocation is applied we achieve more than 20% end-to-end capacity increment in average when compared with an equal resource allocation strategy.

The nitric oxide ISO photocatalytic reactor system: Measurement of NOx removal activity and capacity

Although the NO removal-based air-purification ISO method ISO 22197-1:2007 is well established, its preconditioning requirements mean that only the initial activity of the photocatalyst under test is measured owing to the often-reported, gradual alteration of the surface kinetics for NO oxidation by air through the accumulation of surface HNO3. Herein, we compare the photocatalytic NO removal abilities of a number of different, common TiO2 materials, surface-saturated with photogenerated HNO3, with their behaviours observed during the typical 5 h-long ISO standard test. It is found that all the TiO2 materials studied eventually become largely NO to NO2 converters after sufficient exposure to NO under irradiation (>5 h) due to the accumulation of surface HNO3. The UV exposure time, t*, necessary to reach this HNO3 saturated condition is different for each different catalyst. As a consequence, an alternative preconditioning process for the ISO method is proposed which can be used to provide a more realistic measure of the photocatalytic activity of the underlying material and provide a measure of the NOx removing capacity of the photocatalytic material under test.

Competency-Based Theory For Achieving Innovation: The Case Of Post-Disaster Reconstruction

For those working in the humanitarian sector, achieving positive outcomes for postdisaster communities through reconstruction projects is a pressing concern. In the wake of recent natural disasters, NGOs have become increasingly involved in the permanent reconstruction of affected communities. They have encountered significant barriers as they implement reconstruction programmes and this paper argues that it is important to address the visible lack of innovation that is partially to blame. The theoretical bedrock of a current research project will be used as the starting point for this argument, the overall goal of which is to design a competency-based framework model that can be used by NGOs in post-disaster reconstruction projects. Drawing on established theories of management, a unique perspective has been developed from which a competency-based reconstruction theory emerges. This theoretical framework brings together 3 distinct fields; Disaster Management, Strategic Management and Project Management, each vital
to the success of the model. The objectives of this paper are a) to investigate the role of NGOs in post-disaster reconstruction and establish the current standard of practice b) to determine the extent to which NGOs have the opportunity to contribute to sustainable community development through reconstruction c) to outline the main factors of a theoretical framework first proposed by Von Meding et al. 2009 and d) to identify the innovative measures that can be taken by NGOs to achieve more positive outcomes in their interventions. It is important that NGOs involved in post-disaster reconstruction become familiar with concepts and strategies such as those contained in this paper. Competency-based organizational change on the basis of this theory has the potential to help define the standard of best practice to which future NGO projects might align themselves.

Innovation in tourism: the role of regional innovation systems

Esta tese tem como principal objetivo analisar as características, a importância e o papel da inovação territorial em turismo e o seu impacto no desenvolvimento dos destinos. Consiste num estudo multidisciplinar suportado numa exaustiva revisão da literatura sobre temas como desenvolvimento, inovação e modelos de inovação territorial. Com base nas principais conclusões de natureza conceptual, considerou-se o modelo dos sistemas regionais de inovação como o mais adequado para aplicação ao sistema turístico, e a constituição de redes como estruturas fundamentais para a sua operacionalização. A partir desta abordagem teórica, foi desenvolvido um quadro conceptual para a análise da inovação sistémica no sector do turismo. Esta abordagem permitiu a definição de um conjunto de hipóteses, as quais foram testadas através dos resultados da parte empírica da tese. Foram desenvolvidos dois estudos empíricos distintos, mas complementares nas regiões do Douro e de Aveiro. O primeiro teve como objetivo inquirir empresas turísticas, enquanto o segundo foi dirigido a instituições regionais com intervenção no sector do turismo ou na inovação. Os resultados obtidos conduziram a importantes conclusões sobre o desempenho das empresas e regiões em termos de inovação, os padrões de networking desenvolvidos no âmbito de processos de inovação, a importância do conhecimento existente nas regiões e os fatores específicos das mesmas para a inovação em turismo, a perceção das empresas turísticas sobre o ambiente de inovação e o seu contributo para a evolução e para o sucesso dos destinos turísticos. A tese recorre a uma abordagem quantitativa que inclui estatística descritiva e indutiva e ao método da análise de redes (sociometria). A combinação de métodos levou a importantes conclusões sobre a inovação em turismo, com uma focalização especial no que a relaciona com os sistemas regionais de inovação. As conclusões permitem avançar com um conjunto de implicações e sugestões para futuros projetos de investigação sobre o tema, bem como para a gestão dos destinos turísticos, uma vez que contribui para um maior e mais aprofundado conhecimento do fenómeno da inovação em turismo desenvolvida a nível regional. Os resultados demonstram que diferentes regiões apresentam sistemas regionais de inovação distintos. Assim, não existe um modelo único que possa ser aplicado indistintamente em todas as regiões. Contudo, as conclusões apontam para a existência de padrões e práticas que aperfeiçoam o seu funcionamento, aumentando o desempenho ao nível da inovação, bem como a competitividade global do destino.

Product innovation and the costs of energy-using product policies

Energy-using Products (EuPs) contribute significantly to the United Kingdom’s CO2 emissions, both in the domestic and non-domestic sectors. Policies that encourage the use of more energy efficient products (such as minimum performance standards, energy labelling, enhanced capital allowances, etc.) can therefore generate significant reductions in overall energy consumption and hence, CO2 emissions. While these policies can impose costs on the producers and consumers of these products in the short run, the process of product innovation may reduce the magnitude of these costs over time. If this is the case, then it is important that the impacts of innovation are taken into account in policy impact assessments. Previous studies have found considerable evidence of experience curve effects for EuP categories (e.g. refrigerators, televisions, etc.), with learning rates of around 20% for both average unit costs and average prices; similar to those found for energy supply technologies. Moreover, the decline in production costs has been accompanied by a significant improvement in the energy efficiency of EuPs. Building on these findings and the results of an empirical analysis of UK sales data for a range of product categories, this paper sets out an analytic framework for assessing the impact of EuP policy interventions on consumers and producers which takes explicit account of the product innovation process. The impact of the product innovation process can be seen in the continuous evolution of the energy class profiles of EuP categories over time; with higher energy classes (e.g. A, A+, etc.) entering the market and increasing their market share, while lower classes (e.g. E, F, etc.) lose share and then leave the market. Furthermore, the average prices of individual energy classes have declined over their respective lives, while new classes have typically entered the market at successively lower “launch prices”. Based on two underlying assumptions regarding the shapes of the “lifecycle profiles” for the relative sales and the relative average mark-ups of individual energy classes, a simple simulation model is developed that can replicate the observed market dynamics in terms of the evolution of market shares and average prices. The model is used to assess the effect of two alternative EuP policy interventions – a minimum energy performance standard and an energy-labelling scheme – on the average unit cost trajectory and the average price trajectory of a typical EuP category, and hence the financial impacts on producers and consumers.