Influence of rapid thermal annealing (RTA) on the structural and electrical properties of SnS films

The performance of optoelectronic devices critically depends on the quality of active layer. An effective way to obtain a high quality layers is by creating excess of metal atoms through various heat treatments. Recently, rapid thermal annealing (RTA) has proved a versatile technique for the post-treatment of semiconductor materials as compared to other techniques due to its precise control over the resources. Thus, we carried out a set of experiments on SnS films to explore the influence of RTA treatment on their properties. From these experiments we noticed that the films treated at 400 °C for 1 min in N2 atmosphere have a low electrical resistivity of ~5 Ωcm with relatively high Hall mobility and carrier density of 99 cm2/Vs and 1.3 × 1016 cm−3, respectively. The observed results, therefore, emphasise that it is possible to obtain good quality SnS films through RTA treatment without disturbing their crystal structure.

Influence of Joint Thickness and Mortar-Block Elastic Properties on the Strength and Stresses Developed in Soil-Cement Block Masonry

Soil-cement blocks are employed for load bearing masonry buildings. This paper deals with the study on the influence of bed joint thickness and elastic properties of the soil-cement blocks, and the mortar on the strength and behavior of soil-cement block masonry prisms. Influence of joint thickness on compressive strength has been examined through an experimental program. The nature of stresses developed and their distribution, in the block and the mortar of the soil-cement block masonry prism under compression, has been analyzed by an elastic analysis using FEM. Influence of various parameters like joint thickness, ratio of block to mortar modulus, and Poisson's ratio of the block and the mortar are considered in FEM analysis. Some of the major conclusions of the study are: (1) masonry compressive strength is sensitive to the ratio of modulus of block to that of the mortar (Eb/Em) and masonry compressive strength decreases as the mortar joint thickness is increased for the case where the ratio of block to mortar modulus is more than 1; (2) the lateral tensile stresses developed in the masonry unit are sensitive to the Eb/Em ratio and the Poisson's ratio of mortar and the masonry unit; and (3) lateral stresses developed in the masonry unit are more sensitive to the Poisson's ratio of the mortar than the Poisson's ratio of the masonry unit.

Quantification of the inevitable: the influence of soil macrofauna on soil water movement in rehabilitated open-cut mined lands

Recolonisation of soil by macrofauna (especially ants, termites and earthworms) in rehabilitated open-cut mine sites is inevitable and, in terms of habitat restoration and function, typically of great value. In these highly disturbed landscapes, soil invertebrates play a major role in soil development (macropore configuration, nutrient cycling, bioturbation, etc.) and can influence hydrological processes such as infiltration, seepage, runoff generation and soil erosion. Understanding and quantifying these ecosystem processes is important in rehabilitation design, establishment and subsequent management to ensure progress to the desired end goal, especially in waste cover systems designed to prevent water reaching and transporting underlying hazardous waste materials. However, the soil macrofauna is typically overlooked during hydrological modelling, possibly due to uncertainties on the extent of their influence, which can lead to failure of waste cover systems or rehabilitation activities. We propose that scientific experiments under controlled conditions and field trials on post-mining lands are required to quantify (i) macrofauna–soil structure interactions, (ii) functional dynamics of macrofauna taxa,and (iii) their effects on macrofauna and soil development over time. Such knowledge would provide crucial information for soil water models, which would increase confidence in mine waste cover design recommendations and eventually lead to higher likelihood of rehabilitation success of open-cut mining land.

Influence of Lithium Fluoride on the Burning Rate of AP-Polyester Propellant

THE addition of catalysts normally serves the purpose of imparting a desired burning rate change in a composite propellant. These may either retard or enhance the burning rate. Some often quoted catalysts are oxides, chromites and chromates of metals. A lot of work has been done on rinding the effect of the addition of some of these catalysts on the burning rate; however, none seems to have appeared on the influence of lithium fluoride (LiF). Only qualitative reduction in the burning rate of composite propellants with the addition of LiF was reported by Williams et al.1 Dickinson and Jackson2 reported a slight decrease in the specific impulse of composite propellant with the addition of LiF; however, they made no mention of the effect of its addition on the burning rate. We have studied the effect of the addition of varying amounts of LiF on the burning rate of Ammonium Perchlorate (AP)-Polyester propellant.

Measuring free ellagic acid: influence of extraction conditions on recovery by studying solubility and UV-Visible spectra

Recent investigations into plant tissues have indicated that the free form of the natural polyphenolic antioxidant, ellagic acid (EA), is much more plentiful than first envisaged; consequently a re-assessment of solvent systems for the extraction of this water-insoluble form is needed. As EA solubility and its UV-Vis spectrum, commonly used for detection and quantification, are both governed by pH, an understanding of this dependence is vital if accurate EA measurements are to be achieved. After evaluating the pH effects on the solubility and UV-Vis spectra of commercial EA, an extraction protocol was devised that promoted similar pH conditions for both standard solutions and plant tissue extracts. The extraction so devised followed by HPLC with photodiode-array detection (DAD) provided a simple, sensitive and validated methodology that determined free EA in a variety of plant extracts. The use of 100 % methanol or a triethanolamine-based mixture as the standard dissolving solvents were the best choices, while these higher pH-generating solvents were more efficient in extracting EA from the plants tested with the final choice allied to the plants’ natural acidity. Two of the native Australian plants anise myrtle (Syzygium anisatum) and Kakadu plum (Terminalia ferdinandiana) exhibited high concentrations of free EA. Furthermore, the dual approach to measuring EA UV-Vis spectra made possible an assessment of the effect of acidified eluent on EA spectra when the DAD was employed.

Being online, living offline: The influence of social ties over the appropriation of social network sites

Research on social network sites has examined how people integrate offline and online life, but with a particular emphasis on their use by friendship groups. We extend earlier work by examining a case in which offline ties are non-existent, but online ties strong. Our case is a study of bodybuilders, who explore their passion with like-minded offline 'strangers' in tightly integrated online communities. We show that the integration of offline and online life supports passion-centric activities, such as bodybuilding.

Consumers' perceptions and attitudes towards firms' green marketing initiatives: How do they influence green consumption?

This thesis examines green marketing and green consumption behaviours addressing limited understandings about how consumers interpret their green consumption behaviour in their everyday lives; what motivates people to purchase green products, and what barriers exist to this behaviour. Findings reveal that enhancing green consumption through green marketing depends on consumers' enthusiasm to engage in green practices and green behavioural influences. The research supports the need for qualitative research to provide rich insights into relationships between consumer behaviour, green marketing and green consumption and builds a stronger knowledge foundation by introducing social practice theory into the marketing discipline.

Taxonomy of factors which influence heavy metal build-up on urban road surfaces

Heavy metals build-up on urban road surfaces is a complex process and influenced by a diverse range of factors. Although numerous research studies have been conducted in the area of heavy metals build-up, limited research has been undertaken to rank these factors in terms of their influence on the build-up process. This results in limitations in the identification of the most critical factor/s for accurately estimating heavy metal loads and for designing effective stormwater treatment measures. The research study undertook an in-depth analysis of the factors which influence heavy metals build-up based on data generated from a number of different geographical locations around the world. Traffic volume was found to be the highest ranked factor in terms of influencing heavy metals build-up while land use was ranked the second. Proximity to arterial roads, antecedent dry days and road surface roughness has a relatively lower ranking. Furthermore, the study outcomes advances the conceptual understanding of heavy metals build-up based on the finding that with increasing traffic volume, total heavy metal build-up load increases while the variability decreases. The outcomes from this research study are expected to contribute to more accurate estimation of heavy metals build-up loads leading to more effective stormwater treatment design.

Influence of uncertainty inherent to heavy metal build-up and wash-off on stormwater quality

Uncertainty inherent to heavy metal build-up and wash-off stems from process variability. This results in inaccurate interpretation of stormwater quality model predictions. The research study has characterised the variability in heavy metal build-up and wash-off processes based on the temporal variations in particle-bound heavy metals commonly found on urban roads. The study outcomes found that the distribution of Al, Cr, Mn, Fe, Ni, Cu, Zn, Cd and Pb were consistent over particle size fractions <150µm and >150µm, with most metals concentrated in the particle size fraction <150µm. When build-up and wash-off are considered as independent processes, the temporal variations in these processes in relation to the heavy metals load are consistent with variations in the particulate load. However, the temporal variations in the load in build-up and wash-off of heavy metals and particulates are not consistent for consecutive build-up and wash-off events that occur on a continuous timeline. These inconsistencies are attributed to interactions between heavy metals and particulates <150µm and >150µm, which are influenced by particle characteristics such as organic matter content. The behavioural variability of particles determines the variations in the heavy metals load entrained in stormwater runoff. Accordingly, the variability in build-up and wash-off of particle-bound pollutants needs to be characterised in the description of pollutant attachment to particulates in stormwater quality modelling. This will ensure the accounting of process uncertainty, and thereby enhancing the interpretation of the outcomes derived from modelling studies.

Influence of adhesive non-linearities on the performance and optimal length of adhesive bonded joints

An analytical study for the static strength of adhesive lap joints is presented. The earlier solutions of Volkersen [i], DeBruyne[2] and others were limited to linear adhesives. The influence of adhesive non-linearity was first considered by Grimes' et al[3] and Dickson et al [4]. Recently Hart-Smith[5] successfully introduced elastic-plastic behaviour of the adhesive. In the present study the problem is formulated for general non-linear adhesive behaviour and an efficient numerical algorithm is written for the solution. Bilinear and trilinear models for the nonlinearity yield closed form analytical solutions.

Temperature influence on the excess interaction parameter of styrene-methyl methacrylate copolymer

Intrinsic viscosity data for polystyrene, poly(methyl methacrylate) and styrene-methyl methacrylate copolymer of azeotropic composition have been used to evaluate the excess interaction parameters at different temperatures in γ-butyrolactone and dimethylformamide. It is found that these values are positive and show a negligible increase with increase in temperature, indicating therefore that the hetero-contact interactions are not influenced by temperature, contrary to the results obtained by Dondos and Benoit for the same copolymer system in p-xylene and iso-amyl acetate.

The influence of esterification of carboxyl groups of ribonuclease-a on its structure and immunological activity

The effect of modification of carboxyl groups of Ribonuclease-Aa on the enzymatic activity and the antigenic structure of the protein has been studied. Modification of four of the eleven free carboxyl groups of the protein by esterification in anhydrous methanol/0.1 M hydrochloric acid resulted in nearly 80% loss in enzymatic activity but had very little influence on the antigenic structure of the protein. Further increases in the modification of the carboxyl groups caused a progressive loss in immunological activity, and the fully methylated RNase-A exhibited nearly 30% immunological activity. Concomitant with this change in the antigenic structure of the protein, the ability of the molecule to complement with RNase-S-protein increased, clearly indicating the unfolding of the peptide "tail" from the remainder of the molecule. The susceptibility to proteolysis, accessibility of methionine residues for orthobenzoquinone reaction and the loss in immunological activity of the more extensively esterified derivatives of RNase-A are suggestive of the more flexible conformation of these derivatives as compared with the compact native conformation. The fact that even the fully methylated RNase-A retains nearly 30% of its immunological activity suggested that the modified protein contained antibody recognizable residual native structure, which presumably accommodates some antigenic determinants.

Knowledge networks and Australian Football League coach development: People of influence

Australian Football League (AFL) generally recognised as the ‘national game’ in Australia has a well established program of coach development. However, research examining AFL coaches’ work and how they learn to perform that work has hitherto not been conducted. The effective preparation of coaches is of prime concern to the AFL and should be informed by an examination of how coaches within the code come to know how to do their coaching work. Therefore, the purpose of this AFL-funded research was to inform coach development programs for current and aspiring AFL coaches.

Influence of Hydrophilic Surface Specificity on the Structural Properties of Confined Water

The influence of chemical specificity of hydrophilic surfaces on the structure of confined water in the subnanometer regime is investigated using grand canonical Monte Carlo Simulations. The structural variations for water confined between hydroxylated silica surfaces are contrasted with water confined between mica surfaces. Although both surfaces are hydrophilic, our Study shows that hydration of potassium ions on the mica surface has a strong influence on the water Structure and solvation force response of confined water. In contrast to the disrupted hydrogen bond network observed for water confined between Mica Surfaces, water between silica surfaces retains its hydrogen bond network displaying bulklike structural features down to surface separations as small as 0.45 nm. Hydrogen bonding of all invariant contact water layer with the surface silanol groups aids in maintaining a constant number of hydrogen bonds per water molecule for the silica surfaces. As a consequence water depletion and rearrangement upon decreasing confinement is a strong function of the hydrophilic surface specificity, particularly at smaller separations. An oscillatory solvation force response is only observed for water confined between Silica surfaces, and bulklike features are observed for both Surfaces above a surface separation of about 1.2 nm. We evaluate and contrast the water density, dipole moment distributions, pi pair correlation functions, and solvation forces as a function of the surface separation.