Diode-pumped passively q-switched Nd : YAG ceramic laser with a Cr4+: YAG crystal-satiable absorber

Transparent polycrystalline Nd:YAG ceramics were fabricated by solid-state reactive sintering a mixture of commercial Al2O3,Y2O3, and Nd2O3 powders. The powders were mixed in ethanol and doped with 0.5 wt% tetraethoxysilane, dried, and pressed. Pressed samples were sintered at 1750 degrees C in vacuum. Transparent fully dense samples with average grain sizes of 10 mu m were obtained. The 1 at.% Nd:YAG ceramic was used to research passively Q-switched laser output with a Cr4+:YAG crystal as a saturable absorber. An average output power of 94 mW with a pulse width of 50 ns was obtained when the incident pump power was 750 mW. The slope efficiency was 13%. The pulse energy is 5 mu J, and the peak power is about 100 W.

Diode-pumped Yb : YAG ceramic laser

Transparent polycrystalline Yb:YAG ceramics were fabricated by solid-state reactive sintering a mixture of commercial Al2O3, Y2O3, and Yb2O3 powders. The powders were mixed in ethanol and doped with 0.5 wt% tetraethoxysilane, dried, and pressed. Pressed samples were sintered at 1730 degrees C in vacuum. Transparent fully dense samples with grain sizes of several micrometers were obtained. The phase from 1500 degrees to 1700 degrees C was important for the grain growth, in which the grains grew quickly and a mass of pores were eliminated from the body of the sample. Annealing was an important step to remove the vacancies of oxygen and transform Yb2+ to Yb3+. The 1 at.% Yb:YAG ceramic sample was pumped by a diode laser to study the laser properties. The maximum output power of 1.02 W was obtained with a slope efficiency of 25% at 1030 nm. The size of the lasering sample was 4 mm x 4 mm x 3 mm.

Synthesis of CaCu3Ti4O12 ceramic via a sol-gel method

The novel nano-ultrafine powders for the preparation of CaCu3Ti4O12 ceramic were prepared by the sol-gel method and citrate auto-ignition method. The obtained precursor powders were pressed, sintered at 1000 degrees C to fabricate microcrystal CaCu3Ti4O12 ceramic. The microcrystalline phase of CaCu3Ti4O12 was confirmed by X-ray powder diffraction (XRD). The morphology and size of the grains of the powders and ceramics under different heat treatments were observed using scanning electron microscopy (SEM). The relative dielectric constant of the ceramic sintered at 1000 degrees C was measured with a magnitude of more than 10(4) at room temperature, which was approaching to those of Pb-containing complex perovskite ceramics, and the loss tangent was less than 0.20 in a broad frequency region. The relative dielectric constant and loss tangent were also compared with that of CaCu3Ti4O12 ceramic prepared by other reported methods. (c) 2006 Elsevier B.V. All rights reserved.

用纳米粉制备Nd：Y1.84La0.16O3透明陶瓷Nd：Y1

用碳酸盐共沉淀法制备一种新的掺钕氧化镧钇（Nd：Y1.84La0.16O3）纳米粉体,得到颗粒细小、均匀、分散性好、粒径为50～60nm的Nd：Y1.84La0.16O3纳米粉体.分别采用Nd：Y1.84La0.16O3纳米粉料和商业粉料,用传统陶瓷无压烧结工艺制备Nd：Y1.84La0.16O3透明陶瓷.Nd：Y1.8vLa0.16O3纳米粉制备的陶瓷样品的组分均匀、几乎不存在第二相,具有较高的透过率.商业粉制备的陶瓷样品因混料不均匀而在晶界处存在部分第二相,降低了陶瓷的透过率.此外,还运用体视学法预测

Growth of highly sensitive thermoluminescent crystal alpha-Al2O3 : C by the temperature gradient technique

In this work, an alpha-Al2O3:C crystal with highly sensitive thermoluminescence was directly grown by the temperature gradient technique (TGT) using Al2O3 and graphite powders as raw materials. The optical and luminescent properties and the dosimetric characteristics of the crystal were investigated. An as-grown alpha-Al2O3:C crystal shows a single glow peak at 462 K and a blue emission peak at 415 nm. The thermoluminescence (TL) response of the crystal shows a linear-sublinear-saturation characteristic. In the dose range from 5 x 10(-6) to 10Gy, the alpha-Al2O3:C crystal shows excellent linearity, and saturation was observed at about 30Gy. The sensitivity of the crystal decreases as the heating rate increases. (c) 2008 Elsevier B.V. All rights reserved.

Growth of alpha-Al2O3:C crystal with highly sensitive optically stimulated luminescence

In this work. an alpha-Al2O3:C crystal was directly grown by the temperature gradient technique (TGT) using Al2O3 and graphite powders as the raw materials. The optical, optically stimulated luminescence (OSL) properties and dosimetric characteristics of as-grown crystal were investigated. As-grown alpha-Al2O3:C crystal shows strong absorption band at 205, 230 and 256 nm. Three-dimensional thermoluminescence (TL) emission spectrum of the crystal shows a single emission peak at similar to 415 nm. The OSL decay curve can be fitted to two exponentials, the faster component and the slower component. The OSL response of the crystal shows a linear-sublinear-saturation characteristic. As-grown alpha-Al2O3:C crystal shows excellent linearity in the dose range from 5 x 10(-6) to 50 Gy. For doses higher than the saturation dose (100 Gy). the OSL sensitivity decreases as the dose increases. Crown Copyright (C) 2008 Published by Elsevier B.V. All rights reserved.

Identificação da formação de titanato de bário a partir de mistura reacional calcinada em diferentes temperaturas via difração de raios X, espectroscopia fotoacústica e análise térmica

Os materiais ferroelétricos têm sido utilizados em muitas áreas da tecnologia e da ciência, pois possuem um grande número de aplicações, como: sensores; transdutores; capacitores; dispositivos ópticos; dentre outras. A busca por novos materiais cerâmicos ferroelétricos tem sido grande. Um dos materiais cerâmicos ferroelétricos mais estudados é o titanato de bário (BT). São vários os métodos de produção e caracterização do titanato de bário. Neste trabalho, pós cerâmicos de titanato de bário foram obtidos por reação do estado sólido a partir de misturas reacionais calcinadas em diferentes temperaturas entre 400C e 900C. Foram três as misturas reacionais: não dopadas; dopadas com 1%; e dopadas com 5% de dióxido de cério (CeO2). A identificação da formação do BT, nos pós cerâmicos produzidos, foi feita a partir de três técnicas de caracterização: difração de raios X (DRX); espectroscopia fotoacústica (PAS); e técnicas de análise térmica. Com a técnica DRX, difratogramas mostraram que a plena formação do titanato de bário ocorreu a partir da temperatura de calcinação de 700C. Para a amostra não dopada com cério e calcinada a 800C, houve deslocamento de todos os picos de difração. Nas amostras dopadas com dióxido de cério houve deslocamento de todos os picos de difração, em relação as amostras não dopadas. Observou-se também que nas amostras dopadas com 5% de CeO2, e calcinadas a 700C e 800C, resíduos de dióxido de cério foram observados nos difratogramas. Com a técnica PAS, espectros de absorção foram obtidos. Foi possível observar uma grande diferença de absorção da amostra calcinada a 600 e 630C, indicando a formação do titanato de bário a partir da temperatura de 630C, nas amostras sem a dopagem dióxido de cério. Houve um alargamento nas bandas de absorção a partir da temperatura de 600C, quando o dióxido de cério entrou na matriz. Foi também possível determinar as energias de band-gap das amostras utilizando o método de Tauc. Com as técnicas de análise térmica, em especial através da técnica termogravimétrica (TG/DTG), foi comprovado que até 400C não havia formação de titanato de bário. Visto que nesta temperatura de calcinação houve a maior perda de massa durante a rampa de aquecimento. O início da formação do titanato de bário foi observado a partir da temperatura de calcinação de 500C, assim como nas técnicas DRX e PAS. Portanto, com os resultados apresentados, foi demonstrada a identificação da formação do titanato de bário nas misturas reacionais calcinadas, com auxílio das potencialidades das três técnicas utilizadas.

Crank-Nicholson method for rate equations in powder random lasers

3rd International Conference on Mathematical Modeling in Physical Sciences (IC-MSQUARE 2014)

Pathology of mixed infections of saprolegniasis-myxosporidiosis in Indian major carp (Catla catla Ham.)

An outbreak of saprolegniasis in Catla catla in composite carp culture ponds were recorded during winter season. The typical cotton wool growths were observed on whole body surfaces of catla along with sporadic mortality. The fungal invasion was only restricted to skin and no fungal elements were visible in any internal organs after periodic acid schiff staining. On histology, periportal accumulation of mononuclear cells in liver, presence of myxosporidean cysts in antieror kidney, eosinophilic granular cells reaction in submucosa of stomach and intestine, dilated and engorged blood vessels of brain along with sloughing of epidermis and hyperplasia at gill lamellar base were pronounced changes. The possible role of release of Saprolegnia toxin in producing internal organs pathology has been discussed.

Studies on the preparation of fish silage. 3. Dried silage products

An investigation was undertaken on the production of dried products from silver belly (Leiognathus splendens) silage mixed with plant filter materials. Silages produced using hydrochloric acid and/or formic acid when mixed with rice bran or maize meal and dried, yielded powders having an acceptable appearance and a pleasant odour, which are suitable for use in compounded chicken feeds.

Superconducting properties of Gd-Ba-Cu-O single grains processed from a new, Ba-rich precursor compound

Gd-Ba-Cu-O (GdBCO) single grains have been previously melt-processed successfully in air using a generic Mg-Nd-Ba-Cu-O (Mg-NdBCO) seed crystal. Previous research has revealed that the addition of a small amount of BaO 2 to the precursor powders prior to melt processing can suppress the formation of Gd/Ba solid solution, and lead to a significant improvement in superconducting properties of the single grains. Research into the effects of a higher Ba content on single grain growth, however, has been limited by the relatively small grain size in the earlier studies. This has been addressed by developing Ba-rich precursor compounds Gd-163 and Gd-143, fabricated specifically to enable the presence of greater concentrations of Ba during the melt process. In this study, we propose a new processing route for the fabrication of high performance GdBCO single grain bulk superconductors in air by enriching the precursor powder with these new Ba rich compounds. The influence of the addition of the new compounds on the microstructures and superconducting properties of GdBCO single grains is reported. © 2008 IOP Publishing Ltd.

Health and disease status of Thai pangas, Pangasius hypophthalmus cultured in rural ponds of Mymensingh, Bangladesh

Thai pangas, Pangasius hypophthalmus is one of the important aquaculture species in Bangladesh. Over the last few years spectacular development has been taking place in Thai pangas farming in Mymensingh district. Due to availability of easy breeding and culture techniques as well as quick return, more and more people are converting their rice fields into pangas farms overnight. The present study was carried out to examine health and disease status of Thai pangas mainly through clinical, histopathological and bacteriological techniques. In addition, for collecting primary data on disease and health status of Thai pangas and the resultant socioeconomic impacts on rural households, questionnaire interview and participatory rural appraisal tools were used with selected farming households in three upazilas of Mymensingh district. The most prevalent diseases as reported by the farmers were red spot, followed by anal protrusion, tail and fin rot, pop eye, dropsy and gill rot. Other conditions like cotton wool type lesion, ulceration and white spot were reported but with lower incidence. Four isolates of Aeromonas hydrophila were recovered from kidney and lesion of diseased fish. Hemorrhage over the body especially near mouth and caudal region was noticed in the fishes associated with aeromonad infection. Internally, kidney, liver and spleen became swollen and enlarged. The isolates varied with their pathogenicity. All the four isolates were sensitive to Nitrofurantoin, Cotrimoxazole and Tetracycline but were resistant to Amoxycilline. An attempt was made to treat diseased fish with extracts from neem leaf, garlic and turmeric. Recovery of infection was monitored through mortality and histopathology. General histopathological changes of different organs were also studied. Extract from neem (Azadirachta indica) leaf gave better result. Telangiectasis, lamellar hypertrophy and hyperplasia hemorrhage, lamellar fusion, necrosis of lamellar epithelial cells, presence of parasites and their cysts were the major pathology of gills. Hemorrhagic lesion, pyknotic nuclei and melanomacrophage centers (MMC) were found in the liver of fish. Major pathologies in kidney of fish included presence of MMC, necrotic and ruptured kidney tubules, severe haemopoietic necrosis, and hemorrhage. The economic loss due to disease in Thai pangas farming was estimated from the difference between expected production and actual production. On an average, Thai pangas farmers of Mymensingh incur a loss of Tk. 23,104/ha/cycle due to fish disease (3.6% of expected total production). The loss, however, varied with location and size of farms, type of farmers and management practices. The study also highlighted fish health management related problems and recommended further work for the development of user-friendly farmer-oriented fish health management packages.

Preparation of edible powder from Jawla (Acetes sp.) prawns

Four methods were employed for the preparation of prawn (Acetes) powder in this study. The analytical characteristics and bacteriological quality of the edible powders are presented for each method.

Influence of dietary proteins on cholesterol levels in albino rats

Six groups of albino rats were fed identical diets, differing in their protein sources for sixty days. The protein sources used were fat free casein, defatted groundnut cake, and defatted fish powders from three species of fishes, namely, the fresh water fish Labeo rohita, the marine fishes, Rastrelliger kanagurta and Otolithus argenteus and marine prawns, Parapenaeopsis stylifera. After sixty days, the levels of cholesterol in the serum, liver and heart of the rats were estimated. The casein group recorded the highest level of cholesterol. Compared to casein, the groundnut protein was distinctly hypocholesterolemic. The fish proteins had a still greater cholesterol lowering ability. Of the proteins used in this study, the proteins of prawns had the maximum hypocholesterolemic effect. An attempt is made to correlate the behaviour of the proteins in this respect, with their respective amino acid compositions.