Effects of magnetostriction and superlattice formation in ferromagnetic thin films

The contribution to the magnetic uniaxial perpendicular anisotropy which arises from substrate constraint through magnetostrictive effects has been measured in Ni-Fe and Ni-Co thin films evaporated on substrates at room temperature. This was accomplished by measuring the perpendicular anisotropy before and after removal of the film from the substrate. Data are given for the fcc crystal structure regions of both alloy systems, but data for Ni-Co include compositions with less than 60% Ni which have a small percentage of the hcp phase mixed with the fcc phase. The constraint contribution to the perpendicular anisotropy correlates well with the value of the bulk magnetostriction constant using the equation ∆K_˔=3/2λ_sσ. Measured values of isotropic stress for films thicker than 600 Å were 1.6 x 10¹⁰ dyn/cm². In films less than 600 Å thick the isotropic stress decreased with decreasing thickness. After removal of the films from the substrates, the measured perpendicular anisotropy deviated from the expected geometrical shape anisotropy near pure Ni in both alloys. This indicates that additional significant sources of anisotropy exist at these compositions.

The effect of substrate constraint on the crystalline anisotropy K₁ of Ni-Fe epitaxial films has been studied by use of a film removal technique, which involves the evaporation of an epitaxial layer of LiF on MgO, the epitaxial growth of the metallic film on the LiF, and the stripping of the film with water soluble tape. Films ranging in composition from 50% to 100% Ni have been studied. For compositions below 90% Ni the experimental values agree reasonably well with the first order theoretical prediction, ∆K₁=[-9/4(C₁₁-C₁₂)λ² 100+9/2C₄₄λ²111].

In order to compare the magnetic properties of epitaxial thin films more completely with the properties of bulk single crystals, Ni-Fe films ranging in composition from 60% to 90% Ni, which were evaporated epitaxially on (100) MgO substrates, have been subsequently annealed at 400°C in a vacuum of less than 10^-7 Torr to form the ordered Ni₃Fe structure near the 75% composition. This ordered structure has been confirmed by electron diffraction.

The saturation magnetization at Ni₃Fe increased about 6% with ordering which is in good agreement with previous bulk data. Measurements of the magnetocrystalline anisotropy energy K₁ for the epitaxial films show the same large changes with ordering as observed in bulk single crystal samples. In the (001) plane the magnetostriction constants ^λ100, ^λ111 are directly related to the induced anisotropy due to a uniform uniaxial strain in the [100] and [110] directions respectively. Assuming that the elastic constants of a film are the same as in bulk material and are unchanged by ordering, the changes in strain sensitivity with ordering for the epitaxial films are found to be in good agreement with values predicted from bulk data. The exchange constant A as measured by ferromagnetic resonance has been measured at the Ni₃Fe composition and found to increase 25% with ordering. This seems to indicate a significant increase in the Curie temperature which has only been inferred indirectly for bulk material.

高稳定激光二极管抽运Nd∶YLF再生放大器

设计并实现了一种放大纳秒激光脉冲的高稳定的激光二极管(LD)抽运Nd∶YLF再生放大器。为了获得高稳定的输出,再生放大器工作在饱和状态。此时,再生放大器输出稳定性最好,而且注入激光脉冲能量波动引起的输出激光脉冲波动被抑制。由于增益饱和效应,再生放大器输出脉冲出现时域波形失真,附加后缀脉冲能够减弱时域波形失真。放大器工作波长1053nm,工作频率1Hz。输入240pJ的3ns方波激光脉冲,输出激光脉冲能量4.2mJ,总增益大于107,不稳定度小于1%(均方根),方波扭曲1.33。为3ns方波激光脉冲引入其本身幅度0.75倍的后缀脉冲,输出激光脉冲方波扭曲由1.33降至1.17。

Highly stable, diode-pumped Nd : YLF regenerative amplifier

We present the design and experimental results for a diode pumped Nd:YLF regenerative amplifier applied to amplify a nanosecond laser pulse. Numerical simulation shows that the maximum output energy and the best stability can be obtained when the regenerative amplifier operates in a saturated mode for all pulse duration and temporal profiles. Using extra post-pulse is a good method to decrease the square-pulse distortion caused by gain saturation effect. The amplifier shows output energy of 4.2mJ with a total energy gain of more than 107 and output energy stability of better than 1% rms. When extra post-pulse is added, square-pulse distortion is decreased from 1.33 to 1.17 for the amplifier that is seeded with an optical pulse of 3 ns.

Preparação e caracterização de microesferas poliméricas com morfologia casca-núcleo e propriedades magnéticas à base de estireno e divinilbenzeno

Foram sintetizadas microesferas poliméricas com propriedades magnéticas e morfologia casca-núcleo por meio da técnica de polimerização em suspensão em duas etapas. O núcleo foi constituído por poli(estireno-co-divinilbenzeno) e magnetita modificada com ácido oleico. Foi avaliada a influência da velocidade de agitação e da concentração de iniciador sobre as características das microesferas utilizadas como núcleo (morfologia, tamanho de partículas, propriedades magnéticas e estabilidade térmica). A casca foi constituída por poli(estireno-co-divinilbenzeno) sem material magnético. Foi avaliado o método de adição da emulsão dos monômeros formadores da casca e o tempo de inchamento dos núcleos na emulsão. As microesferas casca-núcleo foram caracterizadas quanto ao seu aspecto morfológico e à estabilidade térmica. Os núcleos não apresentaram ciclos de histerese, estando assim próximos de um material com propriedades superparamagnéticas. O copolímero sintetizado com a maior velocidade de agitação e a menor concentração de iniciador foi o que apresentou o maior teor de ferro incorporado (3,317 %), a maior magnetização de saturação (2,99 emu/g) e o menor diâmetro médio de partículas (81 m). As microesferas casca-núcleo apresentaram apenas um estágio de degradação e as suas Tmáx foram menores do que a do núcleo. O mapa composicional de ferro confirmou a presença de magnetita na superfície das microesferas casca-núcleo

Síntese e caracterização de microesferas poliméricas reticuladas à base de poli(ácido metacrílico) contendo nanopartículas magnéticas de ferritas de manganês

As nanopartículas de ferritas de manganês (MnFe2O4) tem sido de grande interesse por causa de suas notáveis propriedades magnéticas doces (baixa coercividade e moderada magnetização de saturação) acompanhada com boa estabilidade química e dureza mecânica. A formação de materiais híbridos/compósito estabiliza as nanopartículas magnéticas (NPMs) e gera funcionalidades aos materiais. Entretanto, não foi encontrada na literatura uma discussão sobre a síntese e as propriedades de polímeros polares reticulados à base de ácido metacrílico contendo ferritas de manganês na matriz polimérica. Assim, o objetivo desta Dissertação foi produzir partículas esféricas poliméricas reticuladas, com boas propriedades magnéticas, à base de ácido metacrílico, estireno, divinilbenzeno e ferritas de manganês. Neste trabalho, foram sintetizados compósitos de ferrita de manganês (MnFe2O4) dispersa em copolímeros de poli(ácido-metacrílico-co-estireno-co-divinilbenzeno), via polimerização em suspensão e em semi-suspensão. Foram variados os teores de ferrita (1% e 5%) e a concentração do agente de suspensão (0,2% e 5%). Além disso, foram testadas sínteses contendo a fase orgânica pré-polimerizada, e também a mistura da ferrita na fase orgânica (FO), antes da etapa da polimerização em suspensão. Os copolímeros foram analisados quanto as suas morfologias - microscopia óptica; propriedades magnéticas e distribuição das ferritas na matriz polimérica - VSM, SEM e EDS-X; propriedades térmicas TGA; concentração de metais presentes na matriz polimérica absorção atômica. As ferritas foram avaliadas quanto à cristalografia XRD. A matriz polimérica foi avaliada pela técnica de FTIR. As amostras que foram pré-polimerizadas e as que além de pré-polimerizadas foram misturadas as ferritas de manganês na FO, apresentaram as melhores propriedades magnéticas e uma incorporação maior da ferrita na matriz polimérica. Essas rotas sintéticas fizeram com que os copolímeros não apresentassem aglomeração, e também minimizou a presença de ferritas na superfície das microesferas. Em geral, todos os copolímeros obtidos apresentaram as características de materiais magneticamente doces além do superparamagnetismo. Foi constatado que o aumento da concentração do PVA e a diminuição da concentração da ferrita fazem com que os diâmetros das microesferas decresçam. Os resultados de TGA e DTG mostraram que ao misturar as ferritas na FO, a concentração de material magnético na matriz polimérica aumenta cerca de 10%. Entretanto, somente a amostra PM2550, pré-polimerizada e com as ferritas misturadas na FO (5% de ferrita e 0,2% de PVA), apresentou potencial aplicação. Isso porque as ferritas não ficaram expostas na superfície das microesferas, ou seja, o material magnético fica protegido de qualquer ação externa

GdFeCo／TbFeCo磁超分辨磁光记录薄膜研究

用磁控溅射法制备了GdFeCo／TbFeCo交换耦合两层薄膜，利用不同温度的克尔磁滞回线和VSM磁滞回线研究了读出层（GdFeCo）变温磁化方向变化过程．结果表明，随温度升高读出层从平面磁化转变为垂直磁化，交换耦合两层薄膜具有中心孔探测磁超分辨的基本性能．转变过程主要受饱和磁化强度（Ms）的影响，在GdFeCo的补偿温度附近，读出层的磁化强度较小，退磁场能也较小，在交换耦合的作用下，使读出层（GdFeCo）的磁化方向发生转变．磁化方向的转变在75℃～125℃的温度范围内变化较快．

国产掺镱双包层光纤的激光特性

采用MCVD方法研发了掺镱双包层光纤，并对其结构特性、荧光特性和激光特性进行了测试和研究。其D形内包层尺寸为400／450μm，数值孔径为0．36，纤芯直径约为16μm，数值孔径约为0．18。荧光谱线的范围为1000-1140nm，1030nm处的峰宽大于50nm。采用大功率激光二极管单端泵浦6m长的双包层光纤，在泵浦人纤功率为61W时，获得了32W的激光输出，斜率效率为64％。该光纤在高功率处未发现饱和现象，通过优化光纤参数与泵浦方式还可以提高转化效率和输出功率。实验表明该光纤可以取代进口光纤用作高功率

Output beam quality of edge pumped planar waveguide lasers with confocal unstable resonators

Output beam quality of edge pumped planar waveguide lasers with confocal unstable resonators is investigated by diffraction methods, taking into account gain saturation, asymmetric pumping, and beam interaction. The influences of pumping uniformity, doping concentration, cavity length and effective Fresnel number are analyzed with respect to output beam quality and pumping efficiency. It is found that good beam quality and high efficiency can be obtained with asymmetric pumping and optimized negative branch confocal unstable resonators. (c) 2005 The Optical Society of Japan.

High optical-optical efficiency of 52.5% obtained in high power Nd : YAG ceramic laser

Using a quite uniformly side-around arranged compact pumping system, a high power Nd:YAG ceramic quasi-CW laser has been demonstrated with high optical-to-optical conversion efficiency over 50% for the first time. With 450 W quasi-CW stacked laser diode bars pumping at 808 run. 236 W Output at 1064 run was obtained and no saturation phenomena were observed.

Caracterização de imagens de microtomografia de raios X baseada em descritores de textura

A microtomografia computadorizada (computed microtomography - μCT) permite uma análise não destrutiva de amostras, além de possibilitar sua reutilização. A μCT permite também a reconstrução de objetos tridimensionais a partir de suas seções transversais que são obtidas interceptando a amostra através de planos paralelos. Equipamentos de μCT oferecem ao usuário diversas opções de configurações que alteram a qualidade das imagens obtidas afetando, dessa forma, o resultado esperado. Nesta tese foi realizada a caracterização e análise de imagens de μCT geradas pelo microtomógrafo SkyScan1174 Compact Micro-CT. A base desta caracterização é o processamento de imagens. Foram aplicadas técnicas de realce (brilho, saturação, equalização do histograma e filtro de mediana) nas imagens originais gerando novas imagens e em seguida a quantificação de ambos os conjuntos, utilizando descritores de textura (probabilidade máxima, momento de diferença, momento inverso de diferença, entropia e uniformidade). Os resultados mostram que, comparadas às originais, as imagens que passaram por técnicas de realce apresentaram melhoras quando gerados seus modelos tridimensionais.

Nd : YAG ceramic laser obtained high slope-efficiency of 62% in high power applications

By using quite uniformly nine-stacks side-around arranged compact pumping system, a high power Nd:YAG ceramic quasi-CW laser with high slope efficiency of 62% has been demonstrated. With 450 W quasi-CW stacked laser diode bars pumping at 808 nm, performance of the Nd: YAG ceramic laser with different output coupling mirrors has been investigated. Optimum output power of 236 W at 1064 nm was obtained and corresponding optical-to-optical conversion efficiency was as high as 52.5%. The laser system operated quite stably and no saturation phenomena have been observed, which means higher output laser power could be obtained if injecting higher pumping power. The still-evolving Nd: YAG ceramics are potential super excellent media for high power practical laser applications. (c) 2005 Optical Society of America.

5.5W CWYb3+ : Y2O3 ceramic laser pumped with 970 nm laser diode

CW laser output has been demonstrated for polycrystalline transparent 10 at.% Yb3+-doped Y2O3 ceramics. End-pumped with 970 nm laser diode, a maximum output power of 5.5 W has been obtained with absorbed pump power of 31.1 W. The slope efficiency is 25% while the threshold pump power is 5.6 W. Saturation is not observed in our experiments, indicating higher laser output can be expected with higher pump power. (C) 2004 Elsevier B.V. All rights reserved.

High-energy LDA switched side-pumped electro-optical Q-switched Nd : YAG ceramic laser

By employing a uniformly compact side-pumping system, a high-energy electro-optical Q-switched Nd:YAG ceramic laser has been demonstrated. With 420 W quasi-cw laser-diode-array pumping at 808 ran and a 100 Hz modulating repetition rate, 50 mJ output energy at 1064 nm was obtained with 10 ns pulse width, 5 W average output power, and 5 MW peak power. Its corresponding slope efficiency was 29.8%. The laser system operated quite stably and no saturation phenomena have been observed, which means higher output energy could be expected. Laser parameters between ceramic and single-crystal Nd:YAG lasers have been compared, and pulse characteristics of Nd:YAG ceramic with different repetition rate have been investigated in detail. The still-evolving Nd:YAG ceramics are potential super excellent media for high-energy laser applications. (C) 2007 Optical Society of America.

硬边非稳腔平面波导激光器的光束特性

基于衍射理论和坐标变换,采用数值模拟的方法分析了硬边非稳腔平面波导激光器的光束特性,研究了存在非均匀抽运和增益饱和时,输出激光的光束质量.在端面抽运和边缘抽运时,比较了正支和负支非稳腔的输出光束特性.结果表明：利用优化的离轴硬边非稳腔可以得到近衍射极限的输出.在相同的抽运不均匀性情况下,对于边缘抽运和端面抽运,正支非稳腔的光束质量因子M^2分别为3.9和2.3,而相同条件下负支非稳腔的M^2因子为1.8和1.7.

Hypoxic and low pH water in the nearshore marine environments of Monterey Bay, California: characterizing a decade of oxygen and pH, and drivers of variability.

A decade-long time series recorded in southern Monterey Bay, California demonstrates that the shallow, near-shore environment (17 m depth) is regularly inundated with pulses of cold, hypoxic and low pH water. During these episodes, oxygen can drop to biologically threatening levels, and pH levels were lower than expected. Weekly water chemistry monitoring revealed that the saturation state of aragonite (the more soluble form of calcium carbonate) was often below saturation and had a moderate positive relationship with pH, however, analytical and human error could be high. Pulses of hypoxia and low pH water with the greatest intensity arise at the onset of the spring upwelling season, and fluctuations are strongly semidurnal (tidal) and diurnal. Arrival of cold, hypoxic water on the inner shelf typically occurs 3 days after the arrival of a strong upwelling event and appears to be driven by upwelling modulated by internal tidal fluctuations. I found no relationship between the timing of low-oxygen events and the diel solar cycle nor with terrestrial nutrient input. These observations are consistent with advection of hypoxic water from the deep, offshore environment where water masses experience a general decline of temperature, oxygen and pH with depth, and inconsistent with biochemical forcing. Comparisons with concurrent temperature and oxygen time series taken ~20 km away at the head of the Monterey Canyon show similar patterns but even more intense hypoxic events due to stronger semidiurnal forcing there. Analysis of the durations of exposure to low oxygen levels establishes a framework for assessing the ecological relevance of these events. Increasing oceanic hypoxia and acidification of both surface and deep waters may increase the number, intensity, duration and spatial extent of future intrusions along the Pacific coast. Evaluation of the resiliency of nearshore ecosystems such as kelp forests, rocky reefs and sandy habitats, will require consideration of these events.