Unsteady tip leakage characteristics and heat transfer on turbine blade tip and casing

An unsteady numerical investigation was performed to examine time dependent behaviors of the tip leakage flow structures and heat transfer on the rotor blade tip and casing in a single stage gas turbine engine. A transonic, high-pressure
turbine stage was modeled and simulated using a stage pressure ratio of 3.2. The rotor’s tip clearance was 1.2 mm in height (3% of the rotor span) and its speed was set at 9500 rpm. Periodic flow is observed for each vane passing period. Tip leakage flow as well as heat transfer data showed highly time dependent behaviors. A stator trailing edge shock appears as the turbine stage is operating at transonic conditions. The shock alters the flow condition in the rotor section, namely, the tip leakage flow structures and heat transfer rate distributions. The instantaneous Nusselt number distributions are compared to the time averaged and steady-state results. The same patterns in tip leakage flow
structures and heat transfer rate distributions were observed in both unsteady and steady simulations. However, the unsteady simulation captured the locally time-dependent high heat transfer phenomena caused by the unsteady interaction with the upstream vane trailing-edge shock and the passing wake.

Effect of turbine inlet temperature on blade tip leakage flow and heat transfer

One of the most critical gas turbine engine components, rotor blade tip and casing, are exposed to high thermal load. It becomes a significant design challenge to protect the turbine materials from this severe situation. As a result of geometric complexity and experimental limitations, Computational Fluid Dynamics (CFD) tools have been used to predict blade tip leakage flow aerodynamics and heat transfer at typical engine operating conditions. In this paper, the effect of turbine inlet temperature on the tip leakage flow structure and heat transfer has been studied numerically. Uniform low (LTIT: 444 K) and high (HTIT: 800 K) turbine inlet temperature have been considered. The results showed the higher turbine inlet temperature yields the higher velocity and temperature variations in the leakage flow aerodynamics and heat transfer. For a given turbine geometry and on-design operating conditions, the turbine power output can be increased by 1.48 times, when the turbine inlet temperature increases 1.80 times. Whereas the averaged heat fluxes on the casing and the blade tip become 2.71 and 2.82 times larger, respectively. Therefore, about 2.8 times larger cooling capacity is required to keep the same turbine material temperature. Furthermore, the maximum heat flux on the blade tip of high turbine inlet temperature case reaches up to 3.348 times larger than that of LTIT case. The effect of the interaction of stator and rotor on heat transfer features is also explored using unsteady simulations.

Element-Free Galerkin Modelling of Crack Migration in Composite Laminates

The development of a virtual testing environment, as a cost-effective industrial design tool in the design and analysis of composite structures, requires the need to create models efficiently, as well as accelerate the analysis by reducing the number of degrees of freedom, while still satisfying the need for accurately tracking the evolution of a debond, delamination or crack front. The eventual aim is to simulate both damage initiation and propagation in components with realistic geometrical features, where crack propagation paths are not trivial. Meshless approaches, and the Element-Free Galerkin (EFG) method, are particularly suitable for problems involving changes in topology and have been successfully applied to simulate damage in homogeneous materials and concrete. In this work, the method is utilized to model initiation and mixed-mode propagation of cracks in composite laminates, and to simulate experimentally-observed crack migration which is difficult to model using standard finite element analysis. N

Manipulating plasmon modes in tip-enhanced Raman microscopy

The influence of polarization on the plasmon modes excited in tip-enhanced near-field optical microscopy have been investigated using the Finite Difference Time Domain Method. Analysis of the calculated results have laid particular emphasis on the ability to align local field enhancements with the orientation of molecules in order to optimize Raman signals, with particular relevance to recent experimental work on carbon nanotubes.

A straightforward method to obtain the cohesive laws of bonded joints under mode I loading

A simple procedure to measure the cohesive laws of bonded joints under mode I loading using the double cantilever beam test is proposed. The method only requires recording the applied load–displacement data and measuring the crack opening displacement at its tip in the course of the experimental test. The strain energy release rate is obtained by a procedure involving the Timoshenko beam theory, the specimen’s compliance and the crack equivalent concept. Following the proposed approach the influence of the fracture process zone is taken into account which is fundamental for an accurate estimation of the failure process details. The cohesive law is obtained by differentiation of the strain energy release rate as a function of the crack opening displacement. The model was validated numerically considering three representative cohesive laws. Numerical simulations using finite element analysis including cohesive zone modeling were performed. The good agreement between the inputted and resulting laws for all the cases considered validates the model. An experimental confirmation was also performed by comparing the numerical and experimental load–displacement curves. The numerical load–displacement curves were obtained by adjusting typical cohesive laws to the ones measured experimentally following the proposed approach and using finite element analysis including cohesive zone modeling. Once again, good agreement was obtained in the comparisons thus demonstrating the good performance of the proposed methodology.

Mode III interlaminar fracture of carbon/epoxy laminates using the edge crack torsion (ECT) test

The mode III interlaminar fracture of carbon/epoxy laminates was evaluated with the edge crack torsion (ECT) test. Three-dimensional finite element analyses were performed in order to select two specimen geometries and an experimental data reduction scheme. Test results showed considerable non-linearity before the maximum load point and a significant R-curve effect. These features prevented an accurate definition of the initiation point. Nevertheless, analyses of non-linearity zones showed two likely initiation points corresponding to GIIIc values between 850 and 1100 J/m2 for both specimen geometries. Although any of these values is realistic, the range is too broad, thus showing the limitations of the ECT test and the need for further research.

New oligomer-bound antioxidants for improved flex crack resistance and ozone resistance

New oligomer-bound antioxidants have been prepared by condensation reaction. The efficiency and permanence of these oligomer- bound paraphenylene diamines as antioxidants has been compared with conventional amine type antioxidants in NR, SBR, IIR and NBR and in elastomer blends like NR/BR and NR/SBR. The oligomer-bound antioxidants are found to impart improved ozone, flex resistance and mechanical properties to the vulcanizates of NR, SBR, IIR and NBR and to blends of NR/BR and NR/ SBR in comparison with those containing conventional antioxidants.

Simulation on the process of fatigue crack initiation in a martensitic stainless steel

Die vorliegende Arbeit beschäftigt sich mit der Computersimulation des Rissinitiierungsprozesses für einen martensitischen Stahl, der der niederzyklischen Ermüdung unterworfen wurde. Wie auf der Probenoberfläche beobachtet wurde, sind die Initiierung und das frühe Wachstum dieser Mikrorisse in hohem Grade von der Mikrostruktur abhängig. Diese Tatsache wurde in mesoskopischen Schädigungsmodellen beschrieben, wobei die Körner als einzelne Kristalle mit anisotropem Materialverhalten modelliert wurden. Das repräsentative Volumenelement (RVE), das durch einen Voronoi-Zerlegung erzeugt wurde, wurde benutzt, um die Mikrostruktur des polykristallinen Materials zu simulieren. Spannungsverteilungen wurden mit Hilfe der Finiten-Elemente-Methode mit elastischen und elastoplastischen Materialeigenschaften analysiert. Dazu wurde die Simulation zunächst an zweidimensionalen Modellen durchgeführt. Ferner wurde ein vereinfachtes dreidimensionales RVE hinsichtlich des sowohl dreidimensionalen Gleitsystems als auch Spannungszustandes verwendet. Die kontinuierliche Rissinitiierung wurde simuliert, indem der Risspfad innerhalb jedes Kornes definiert wurde. Die Zyklenanzahl bis zur Rissinitiierung wurde auf Grundlage der Tanaka-Mura- und Chan-Gleichungen ermittelt. Die Simulation lässt auf die Flächendichten der einsegmentige Risse in Relation zur Zyklenanzahl schließen. Die Resultate wurden mit experimentellen Daten verglichen. Für alle Belastungsdehnungen sind die Simulationsergebnisse mit denen der experimentellen Daten vergleichbar.

Dos experiencias socialistas de Formaci??n Profesional en el primer tercio del siglo XX : las escuelas de aprendices tip??grafos y de aprendices metal??rgicos

En este art??culo se analizan dos experiencias formativas ocurridas en el primer tercio del siglo XX, concretamente las escuelas de aprendices tip??graficos y de aprendices metal??rgicos. La finalidad de la primera era proporcionar instrucci??n t??cnica elemental a los j??venes que se dedicaran al arte de la imprenta en la secci??n de cajas. La segunda ten??a como objetivo ser el lugar donde completar la educaci??n pr??ctica que los aprendices recib??an en sus centros de trabajo, mediante ciertos conocimientos te??ricos, a fin de perfeccionar su capacidad profesional.

Phonological recovery in Spanish developmental dyslexics through the tip-of-the-tongue paradigm

Resumen tomado de la publicación

O jornal e os discursos sobre a droga a produção de sentidos sobre as medidas de enfrentamento do crack presentes n\2018O Globo em 2013

Partindo da premissa de que o jornal é um espaço privilegiado para a oferta de sentidos sobre o mundo, esta pesquisa tem como proposta investigar o modo como o jornal O Globo, construiu e fez circular os sentidos sobre as drogas, principalmente o crack, em 2013. Do ponto de vista da saúde pública, neste ano, travou-se o debate em torno da votação do PL 7663/2010 que, entre outros aspectos, propõe mudanças na legislação referente às alternativas de tratamento da dependência química. Nosso corpus de análise é formado pelos textos publicados n\2019O Globo, no período de janeiro a dezembro de 2013, que abordaram o eixo crack, internação compulsória e Projeto de Lei 7663/2010. Como referências teórico-metodológicas utilizamos os postulados da Semiologia dos Discursos Sociais, trabalhando ainda conceitos propostos por teóricos como Pierre Bourdieu, Mikhail Bakhtin, Eliseo Verón, Muniz Sodré e Michel Foucault a partir de reflexões sobre campo social, discurso, poder e midiatização. Tomando por base as construções enunciativas analisadas, destacamos que apesar de mostrar-se contrário a alguns aspectos da internação, o jornal O Globo defendia a mesma como alternativa para conter a epidemia de crack