Computational Analysis and Optimization of Real Gas Flow In Small Centrifugal Compressors

Small centrifugal compressors are more and more widely used in many industrialsystems because of their higher efficiency and better off-design performance comparing to piston and scroll compressors as while as higher work coefficient perstage than in axial compressors. Higher efficiency is always the aim of the designer of compressors. In the present work, the influence of four partsof a small centrifugal compressor that compresses heavy molecular weight real gas has been investigated in order to achieve higher efficiency. Two parts concern the impeller: tip clearance and the circumferential position of the splitter blade. The other two parts concern the diffuser: the pinch shape and vane shape. Computational fluid dynamics is applied in this study. The Reynolds averaged Navier-Stokes flow solver Finflo is used. The quasi-steady approach is utilized. Chien's k-e turbulence model is used to model the turbulence. A new practical real gas model is presented in this study. The real gas model is easily generated, accuracy controllable and fairly fast. The numerical results and measurements show good agreement. The influence of tip clearance on the performance of a small compressor is obvious. The pressure ratio and efficiency are decreased as the size of tip clearance is increased, while the total enthalpy rise keeps almost constant. The decrement of the pressure ratio and efficiency is larger at higher mass flow rates and smaller at lower mass flow rates. The flow angles at the inlet and outlet of the impeller are increased as the size of tip clearance is increased. The results of the detailed flow field show that leakingflow is the main reason for the performance drop. The secondary flow region becomes larger as the size of tip clearance is increased and the area of the main flow is compressed. The flow uniformity is then decreased. A detailed study shows that the leaking flow rate is higher near the exit of the impeller than that near the inlet of the impeller. Based on this phenomenon, a new partiallyshrouded impeller is used. The impeller is shrouded near the exit of the impeller. The results show that the flow field near the exit of the impeller is greatly changed by the partially shrouded impeller, and better performance is achievedthan with the unshrouded impeller. The loading distribution on the impeller blade and the flow fields in the impeller is changed by moving the splitter of the impeller in circumferential direction. Moving the splitter slightly to the suction side of the long blade can improve the performance of the compressor. The total enthalpy rise is reduced if only the leading edge of the splitter ismoved to the suction side of the long blade. The performance of the compressor is decreased if the blade is bended from the radius direction at the leading edge of the splitter. The total pressure rise and the enthalpy rise of thecompressor are increased if pinch is used at the diffuser inlet. Among the fivedifferent pinch shape configurations, at design and lower mass flow rates the efficiency of a straight line pinch is the highest, while at higher mass flow rate, the efficiency of a concave pinch is the highest. The sharp corner of the pinch is the main reason for the decrease of efficiency and should be avoided. The variation of the flow angles entering the diffuser in spanwise direction is decreased if pinch is applied. A three-dimensional low solidity twisted vaned diffuser is designed to match the flow angles entering the diffuser. The numerical results show that the pressure recovery in the twisted diffuser is higher than in a conventional low solidity vaned diffuser, which also leads to higher efficiency of the twisted diffuser. Investigation of the detailed flow fields shows that the separation at lower mass flow rate in the twisted diffuser is later than in the conventional low solidity vaned diffuser, which leads to a possible wider flow range of the twisted diffuser.

Introducing Basic Systematic Requirements Engineering Practices in Small Organizations with an Easy to Adopt Method

Requirements-relatedissues have been found the third most important risk factor in software projects and as the biggest reason for software project failures. This is not a surprise since; requirements engineering (RE) practices have been reported deficient inmore than 75% of all; enterprises. A problem analysis on small and low maturitysoftware organizations revealed two; central reasons for not starting process improvement efforts: lack of resources and uncertainty; about process improvementeffort paybacks.; In the constructive part of the study a basic RE method, BaRE, was developed to provide an; easy to adopt way to introduce basic systematic RE practices in small and low maturity; organizations. Based on diffusion of innovations literature, thirteen desirable characteristics; were identified for the solution and the method was implemented in five key components:; requirements document template, requirements development practices, requirements; management practices, tool support for requirements management, and training.; The empirical evaluation of the BaRE method was conducted in three industrial case studies. In; this evaluation, two companies established a completely new RE infrastructure following the; suggested practices while the third company conducted continued requirements document; template development based on the provided template and used it extensively in practice. The; real benefits of the adoption of the method were visible in the companies in four to six months; from the start of the evaluation project, and the two small companies in the project completed; their improvement efforts with an input equal to about one person month. The collected dataon; the case studies indicates that the companies implemented new practices with little adaptations; and little effort. Thus it can be concluded that the constructed BaRE method is indeed easy to; adopt and it can help introduce basic systematic RE practices in small organizations.

Essays on Innovativeness and its Evaluation in Small and Medium-sized Enterprises

Tutkimus koostuu neljästä artikkelista, jotka käsittelevät suomalaisten pienten ja keskisuurten teollisuusyritysten (PKT-yritysten) innovatiivisuutta, sen attribuutteja (ominaispiirteitä) sekä indikaattoreita. Tutkimuksessa tarkastellaan sekä kirjallisuudessa esitettyjä että PKT-johtajien ja PKT-yritystenkehityshankkeiden rahoituspäätöksiin osallistuvien yritystutkijoiden haastatteluissa esittämiä innovatiivisuuden määritelmiä. Innovatiivisuusindikaattoreista tarkastellaan PKT-yritysten kehittämishankkeille sovellettavia rahoitus- ja arviointikriteerejä sekä yritysten ulkopuolisten rahoittajien että PKT-johtajien näkökulmasta. Erityistä huomiota kohdistetaan sovellettuihin laadullisiin ja ei-numeerisiin innovatiivisuuden arviointikriteereihin. Sekä kirjallisuudessa että kymmenen yritystutkijan ja kuuden esimerkkiyrityksen johtajan haastatteluissa innovaation uutuus yhdistetään innovatiivisuuteen. Muita tärkeitä innovatiivisuuteen liitettyjä ominaisuuksia olivat markkinat, muista yrityksistä erottuminen ja yksilöiden luovuus. Ihmisläheiset ja yksilöihin liittyvät näkökulmat korostuvat yritystutkijoiden ja PKT-johtajien innovatiivisuuden määritelmissä, kun taas kirjallisuudessa annetaan enemmän painoa ympäristölle, tuotteille ja markkinoille. Yritystutkijat pitivät yritykseen ja sen johtajaan liittyviä tekijöitä tärkeinä rahoitettavien kehittämishankkeiden panosten arviointikriteereinä. Tuotteiden kaupallinen menestys oli rahoittajan kannalta tärkein tulostekijä. Tarkastelluissa esimerkkiyrityksissä kehityshankkeista päättäminen ja hankkeiden arviointi on toisaalta intuitiivista ja saattaa olla tiedostamatontakin, koska yritysten kehittämistoiminta on vähäistä. Pienyritysten johtajat korostavat arvioinnissa rahallisiamittareita, vaikka sekä numeerisia että laadullisia kriteereitä sovelletaan. Todennäköisin syy tälle on pienyritysten rajalliset taloudelliset voimavarat. Toinen mahdollinen syy rahoituksellisten tekijöiden painottamiseen on, että tämän päivän ihannejohtaja ymmärretään analyyttiseksi ja mm.rahavirtoja valvovaksi. Kuitenkin innovatiiviset yritysjohtajat pitävät innovaatioiden luomista yhtenä elämän hauskoista puolista. Innovatiiviset esimerkkiyritykset ovat tulevaisuuteen ja kasvuun suuntautuneita strategisella tasolla. Operationaalisella tasolla ne tuottavat keksintöjä ja innovaatioita. Patentteja tarkastelluilla yrityksillä on kuitenkin vähän. Sekä innovatiiviset että vähemmän innovatiiviset esimerkkiyritykset ovat voimakkaasti asiakassuuntautuneita ja erikoistuneita tiettyihin tuotteisiin ja asiakkaisiin. Asiakkaiden tarpeita tyydytetään kehittämällä niitä vastaavia tuotteita. Tästä johtuu, että valtaosa yritysten kehittämistoiminnasta kohdistuu tuotteisiin tai tuotantoon.

Dynamic Model of a Small Once-Through Boiler

In this study, a model for the unsteady dynamic behaviour of a once-through counter flow boiler that uses an organic working fluid is presented. The boiler is a compact waste-heat boiler without a furnace and it has a preheater, a vaporiser and a superheater. The relative lengths of the boiler parts vary with the operating conditions since they are all parts of a single tube. The present research is a part of a study on the unsteady dynamics of an organic Rankine cycle power plant and it will be a part of a dynamic process model. The boiler model is presented using a selected example case that uses toluene as the process fluid and flue gas from natural gas combustion as the heat source. The dynamic behaviour of the boiler means transition from the steady initial state towards another steady state that corresponds to the changed process conditions. The solution method chosen was to find such a pressure of the process fluid that the mass of the process fluid in the boiler equals the mass calculated using the mass flows into and out of the boiler during a time step, using the finite difference method. A special method of fast calculation of the thermal properties has been used, because most of the calculation time is spent in calculating the fluid properties. The boiler was divided into elements. The values of the thermodynamic properties and mass flows were calculated in the nodes that connect the elements. Dynamic behaviour was limited to the process fluid and tube wall, and the heat source was regarded as to be steady. The elements that connect the preheater to thevaporiser and the vaporiser to the superheater were treated in a special way that takes into account a flexible change from one part to the other. The model consists of the calculation of the steady state initial distribution of the variables in the nodes, and the calculation of these nodal values in a dynamic state. The initial state of the boiler was received from a steady process model that isnot a part of the boiler model. The known boundary values that may vary during the dynamic calculation were the inlet temperature and mass flow rates of both the heat source and the process fluid. A brief examination of the oscillation around a steady state, the so-called Ledinegg instability, was done. This examination showed that the pressure drop in the boiler is a third degree polynomial of the mass flow rate, and the stability criterion is a second degree polynomial of the enthalpy change in the preheater. The numerical examination showed that oscillations did not exist in the example case. The dynamic boiler model was analysed for linear and step changes of the entering fluid temperatures and flow rates.The problem for verifying the correctness of the achieved results was that there was no possibility o compare them with measurements. This is why the only way was to determine whether the obtained results were intuitively reasonable and the results changed logically when the boundary conditions were changed. The numerical stability was checked in a test run in which there was no change in input values. The differences compared with the initial values were so small that the effects of numerical oscillations were negligible. The heat source side tests showed that the model gives results that are logical in the directions of the changes, and the order of magnitude of the timescale of changes is also as expected. The results of the tests on the process fluid side showed that the model gives reasonable results both on the temperature changes that cause small alterations in the process state and on mass flow rate changes causing very great alterations. The test runs showed that the dynamic model has no problems in calculating cases in which temperature of the entering heat source suddenly goes below that of the tube wall or the process fluid.

Analysis of the voltage source inverter with small DC-link capacitor

IIn electric drives, frequency converters are used to generatefor the electric motor the AC voltage with variable frequency and amplitude. When considering the annual sale of drives in values of money and units sold, the use of low-performance drives appears to be in predominant. These drives have tobe very cost effective to manufacture and use, while they are also expected to fulfill the harmonic distortion standards. One of the objectives has also been to extend the lifetime of the frequency converter. In a traditional frequency converter, a relatively large electrolytic DC-link capacitor is used. Electrolytic capacitors are large, heavy and rather expensive components. In many cases, the lifetime of the electrolytic capacitor is the main factor limiting the lifetime of the frequency converter. To overcome the problem, the electrolytic capacitor is replaced with a metallized polypropylene film capacitor (MPPF). The MPPF has improved properties when compared to the electrolytic capacitor. By replacing the electrolytic capacitor with a film capacitor the energy storage of the DC-linkwill be decreased. Thus, the instantaneous power supplied to the motor correlates with the instantaneous power taken from the network. This yields a continuousDC-link current fed by the diode rectifier bridge. As a consequence, the line current harmonics clearly decrease. Because of the decreased energy storage, the DC-link voltage fluctuates. This sets additional conditions to the controllers of the frequency converter to compensate the fluctuation from the supplied motor phase voltages. In this work three-phase and single-phase frequency converters with small DC-link capacitor are analyzed. The evaluation is obtained with simulations and laboratory measurements.

Stereotactic body radiotherapy with helical TomoTherapy for medically inoperable early stage primary and second-primary non-small-cell lung neoplasm: 1-year outcome and toxicity analysis.

OBJECTIVE: This study investigated the effectiveness of stereotactic body radiotherapy with helical TomoTherapy (T-SBRT) for treating medically inoperable primary and second-primary early stage non-small-cell lung neoplasm (SPLN) and evaluated whether the movement of organizing pneumonia (OP) within the irradiation field (IF) can be detected via analysis of radiological changes. METHODS: Patients (n = 16) treated for 1 year (2011-12) at our hospital by T-SBRT at a total dose of 60 Gy in five fractions were examined retrospectively. Outcome and toxicity were recorded and were separately described for SPLN. CT scans were reviewed by a single radiologist. RESULTS: Of the 16 patients, 5 (31.3%) had primary lung malignancies, 10 (62.5%) had SPLN, and 1 case (6.3%) had isolated mediastinal metastasis of lung neoplasm. Pathological evidence was obtained for 72.2% of all lesions. The median radiological follow-up was 11 months (10.5 months for SPLN). For all cases, the 6- and 12-month survival rates were 100% and 77.7% (100% and 71.4%, respectively, for SPLN), and the 6- and 12-month locoregional control rates were 100% in all cases. 2 (12.5%) of 16 patients developed grade 3 late transient radiation pneumonitis following steroid therapy and 1 (6.3%) presented asymptomatic infiltrates comparable to OP opacities. CONCLUSION: T-SBRT seems to be safe and effective. ADVANCES IN KNOWLEDGE: Mild OP is likely associated with radiation-induced anomalies in the IF, identification of migrating opacities can help discern relapse of radiation-induced opacities.

Les lésions de l'intestin grêle et du côlon dans les traumatismes fermés de l'abdomen [Lesions of the small intestine and colon in blunt injuries of the abdomen].

Between 1976 and 1991, we observed lesions of the small bowel or colon in 39 patients having sustained blunt abdominal trauma. 70% of the patients presented with concomitant injuries. Except for 3 cases, all the patients presented with abdominal pain on admission. All the patients were operated on. The delay between admission and operation varied between a few minutes and 48 hours. Indication was hemoperitoneum, peritonitis or progressive abdominal pain. Overall morbidity is high, often related to associated disease. 4 patients died (mortality 10%), including 2 patients with isolated intestinal trauma who were operated on after 20 and 36 hours. Due to the lack of specific laboratory or X-ray test, we suggest a high index of suspicion for bowel lesions in blunt abdominal trauma, especially in unconscious patients. Close observation is mandatory. Indication for laparotomy must not be delayed if any doubt exists regarding the integrity of hollow viscus.

Agile Methods in Small Software Projects

Agile software development methods are attempting to provide an answer to the software development industry's need of lighter weight, more agile processes that offer the possibility to react to changes during the software development process. The objective of this thesis is to analyze and experiment the possibility of using agile methods or practices also in small software projects, even in projects containing only one developer. In the practical part of the thesis a small software project was executed with some agile methods and practices that in the theoretical part of the thesis were found possible to be applied to the project. In the project a Bluetooth proxy application that is run in the S60 smartphone platform and PC was developed further to contain some new features. As a result it was found that certain agile practices can be useful even in the very small projects. The selection of the suitable practices depends on the project and the size of the project team.

Risks in R&D Collaboration between Small and Large Firms

The main aim of this thesis was to find out what kinds of risks arise from collabo-ration in R&D between small and large firms. The suitability and gain of some buyer/supplier risk frameworks in examining of R&D collaboration has been in-vestigated. A risk model has been based on the buyer/supplier risks models found in the literature. Its applicability has been tested empirically by means of theme interviews with firm representatives. The risk classification framework received some confirmation. But the study also showed that the theoretical framework was not completely adequate, as a new risk class arose from communication. Collaboration causes risks, and these risks should be taken into account when R&D collaboration is planned. The advantage of risk examination is the possibility to decrease failures and losses, and to in-crease possibilities for success and economical benefits. This study should be used as a managerial analysis tool in trying to understand the form and concept of risk in risk expectancy.

Core Competence of a Small or Medium Sized Content Providing Company Operating in the Information and Communication Technologies Secto

Tutkimuksen tavoitteena on tarkastella tekijöitä, joista ydinosaaminen muodostuu, sekä sitä kuinka yritykset voisivat parhaiten hyödyntää omia resurssejaan ja osaamistaan tunnistetun ydinosaamisen avulla. Teoria osuudessa käydään läpi kuinka ydinosaaminen on kirjallisuudessa määritelty ja miten yritykset voivat sen määritellä sisäisesti itselleen. Empiirisessä osiossa käydään läpi Telecom Business Research Centerissä tehdyn kvantitatiivisen selvityksen pohjalta valitut kolme sisällöntuottaja case - yritystä sekä kuvataan näiden osaamista. Tiedot yrityksistä perustuvat niiden edustajille tehtyihin haastatteluihin ja heidän käsitykseensä omasta yrityksestään. Tämä näkemys on tutkimuksen kannalta äärimmäisen relevanttia, koska ydinosaamisen määrittely tehdään yrityksessä sisäisesti juuri haastatellun kaltaisten yrityksen ydintoimijoiden toimesta. Varsinaisten case -yritysten lisäksi käydään läpi käytännön tapaus action-oriented -tutkimusosuudessa. Tutkimusta ja siinä käsiteltyjä esimerkkejä tulisi hyödyntää yrityksen oman ydinosaamisselvityksen apuna prosessin varrella.

Being Small for Gestational Age: Does it Matter for the Neurodevelopment of Premature Infants? A Cohort Study.

BACKGROUND: Whether being small for gestational age (SGA) increases the risk of adverse neurodevelopmental outcome in premature infants remains controversial. OBJECTIVE: to study the impact of SGA (birthweight < percentile 10) on cognition, behavior, neurodevelopmental impairment and use of therapy at 5 years old. METHODS: This population-based prospective cohort included infants born before 32 weeks of gestation. Cognition was evaluated with the K-ABC, and behavior with the Strengths and Difficulties Questionnaire (SDQ). Primary outcomes were cognitive and behavioral scores, as well as neurodevelopmental impairment (cognitive score < 2SD, hearing loss, blindness, or cerebral palsy). The need of therapy, an indirect indicator of neurodevelopmental impairment, was a secondary outcome. Linear and logistic regression models were used to analyze the association of SGA with neurodevelopment. RESULTS: 342/515 (76%) premature infants were assessed. SGA was significantly associated with hyperactivity scores of the SDQ (coefficient 0.81, p < 0.04), but not with cognitive scores, neurodevelopmental impairment or the need of therapy. Gestational age, socio-economic status, and major brain lesions were associated with cognitive outcome in the univariate and multivariate model, whereas asphyxia, sepsis and bronchopulmonary dysplasia were associated in the univariate model only. Severe impairment was associated with fetal tobacco exposition, asphyxia, gestational age and major brain lesions. Different neonatal factors were associated with the use of single or multiple therapies: children with one therapy were more likely to have suffered birth asphyxia or necrotizing enterocolitis, whereas the need for several therapies was predicted by major brain lesions. DISCUSSION: In this large cohort of premature infants, assessed at 5 years old with a complete panel of tests, SGA was associated with hyperactive behavior, but not with cognition, neurodevelopmental impairment or use of therapy. Birthweight <10th percentile alone does not appear to be an independent risk factor of neurodevelopmental adverse outcome in preterm children.