Evaluation of the Evidential Value of the Elemental Composition of Glass, Ink and Paper by Laser-Based Micro-Spectrochemical Methods

Elemental analysis can become an important piece of evidence to assist the solution of a case. The work presented in this dissertation aims to evaluate the evidential value of the elemental composition of three particular matrices: ink, paper and glass. In the first part of this study, the analytical performance of LIBS and LA-ICP-MS methods was evaluated for paper, writing inks and printing inks. A total of 350 ink specimens were examined including black and blue gel inks, ballpoint inks, inkjets and toners originating from several manufacturing sources and/or batches. The paper collection set consisted of over 200 paper specimens originating from 20 different paper sources produced by 10 different plants. Micro-homogeneity studies show smaller variation of elemental compositions within a single source (i.e., sheet, pen or cartridge) than the observed variation between different sources (i.e., brands, types, batches). Significant and detectable differences in the elemental profile of the inks and paper were observed between samples originating from different sources (discrimination of 87 – 100% of samples, depending on the sample set under investigation and the method applied). These results support the use of elemental analysis, using LA-ICP-MS and LIBS, for the examination of documents and provide additional discrimination to the currently used techniques in document examination. In the second part of this study, a direct comparison between four analytical methods (µ-XRF, solution-ICP-MS, LA-ICP-MS and LIBS) was conducted for glass analyses using interlaboratory studies. The data provided by 21 participants were used to assess the performance of the analytical methods in associating glass samples from the same source and differentiating different sources, as well as the use of different match criteria (confidence interval (±6s, ±5s, ±4s, ±3s, ±2s), modified confidence interval, t-test (sequential univariate, p=0.05 and p=0.01), t-test with Bonferroni correction (for multivariate comparisons), range overlap, and Hotelling’s T2 tests. Error rates (Type 1 and Type 2) are reported for the use of each of these match criteria and depend on the heterogeneity of the glass sources, the repeatability between analytical measurements, and the number of elements that were measured. The study provided recommendations for analytical performance-based parameters for µ-XRF and LA-ICP-MS as well as the best performing match criteria for both analytical techniques, which can be applied now by forensic glass examiners.

Engineering interfacial silicon dioxide for improved metal-insulator-semiconductor silicon photoanode water splitting performance

Silicon photoanodes protected by atomic layer deposited (ALD) TiO2 show promise as components of water splitting devices that may enable the large-scale production of solar fuels and chemicals. Minimizing the resistance of the oxide corrosion protection layer is essential for fabricating efficient devices with good fill factor. Recent literature reports have shown that the interfacial SiO2 layer, interposed between the protective ALD-TiO2 and the Si anode, acts as a tunnel oxide that limits hole conduction from the photoabsorbing substrate to the surface oxygen evolution catalyst. Herein, we report a significant reduction of bilayer resistance, achieved by forming stable, ultrathin (<1.3 nm) SiO2 layers, allowing fabrication of water splitting photoanodes with hole conductances near the maximum achievable with the given catalyst and Si substrate. Three methods for controlling the SiO2 interlayer thickness on the Si(100) surface for ALD-TiO2 protected anodes were employed: (1) TiO2 deposition directly on an HF-etched Si(100) surface, (2) TiO2 deposition after SiO2 atomic layer deposition on an HF-etched Si(100) surface, and (3) oxygen scavenging, post-TiO2 deposition to decompose the SiO2 layer using a Ti overlayer. Each of these methods provides a progressively superior means of reliably thinning the interfacial SiO2 layer, enabling the fabrication of efficient and stable water oxidation silicon anodes.

Francisco Pizarro' s banner of arms: an analytical work contributing to latin America's history

The study of textiles is an open area of scientific research, which for its variety of material components and physical chemical diversity of conditions, makes a field of interest for scientific studies in the cultural heritage field. Archaeological/historical textiles offer the possibility to carry out studies on organic materials such as fibers, adhesion elements, dyes, paper, etc., as well as on inorganic compounds for instance metals, alloys, precious stones and other added ornamentation. That variety of composition, allow to use a combination of analytical techniques to solve the questions coming from the object in an archaeometric research. One kind of textile object that provides a valuable cultural information because of its linguistic representation employed by its carrier societies, are the flags/banners/emblems, objects made with a nonverbal communication purpose. As long as depending on the use and/or purpose of each object, varies both the materials/techniques used in its production and its iconography (style, color, emblem, shape), its study gives the possibility to extract information through their materials and manufacturing techniques about a temporal-spatial frame, a particular event or a specific character. The flags/banners have been used since the eleventh century as representative objects of power, hierarchy, social or military organization, or as communicative media. The use of these objects has been spread throughout the world, possibly due to its easy interpretation and/or appropriation by different societies, making it part of their own culture. The flags as symbols of territorial control, using emblems that represent a family, order or army, were introduced to the New World (America) with the arrival of the European conquerors at the end of the fifteenth century. Flags/banners representing the Royal dominion over conquered territories, the Catholic Church and conquistadors’ armies were the first to arrive. One of those flags that have endured over time, that have an invaluable cultural meaning for both American and Iberian societies, is the so-called Francisco Pizarro’s Banner of Arms. It is a textile object with metal threads decoration over a Royal emblem. According to historical sources, this object was used by Francisco Pizarro in 1532 on the conquest process of Peru, after received the permission by King Charles V to on behalf of him, to conquer the lands of the New World today known as Peru. After Pizarro’s control of the Inca territory, it is believed that Pizarro left his banner on top of the Inca’s Sun’s Temple as symbol of his rule. Centuries later, in the America libertarian campaigns, General Sucre, military at charge of the independence army in Peru, reports have found what he considered the Pizarro’s Banner, sending it to Bogotá as a symbol of victory, being kept since that time until today by the National Museum of Colombia. Due to historical discrepancies in the different movements of the so-called Pizarro’s Banner of Arms, its real meaning has been under discussion and because of the passage of time its physical condition has suffer deterioration. That is because its scientific study is now an interesting case study to respond to both historical and conservation questions of it. Through a collaboration with the National Museum of Colombia, a set of 25 samples of so-called Pizarro’s Banner of Arms were collected, covering the various components and areas from the object of study. These samples were subjected to analytical studies for physical and chemical characterization. Microscopic observation, VSEM-EDS analysis, Raman spectroscopy, chromatographic analysis (HPLC-MS, GCMS) and radiocarbon dating were done. Similarly, was sought through a direct in situ physical inspection to the object and through a research into historical sources, adequate information to solve the object’s problems. Results obtained allowed to identify as silk the textile used in the elaboration of the Banner’s fabric, as well as the use of natural dyes for dyeing the fibers used on the emblem: use of cochineal and brazil wood as a source of red, luteolin plant-based for yellow color, indigotine plant-based for blue, and a mixture of yellow and blue dyes for green were identified. Similarly, the use of animal glue in the manufacturing process and the use of rag paper was evident. The metal threads study from the Banner give a confirmation to a silver core wire gilded with a thin gold sheet, being flattened and entwined with silk threads for their use. Finally, using the radiocarbon results, it was possible to postulate with huge accuracy that the Banner date manufacture was between the XV-XVI century and subject to restoration processes with addition of textiles in modern times. Together with, was evident that the state of degradation of the fabric is due to natural degradation in the silk fibers, having that its color has faded and its mechanical properties decreased, leading to loss of rigidity and disappearance of the physical structure. Similarly, it was clear the original colors of the emblem and highlight problems of detachment of paper due to crystallization of the adhesive. In the same way, was found that the metal threads suffer corrosion by sulfur and detachment of its crystals. Finally, combining the analytical results and the historical sources data found from the so-called Francisco Pizarro’s Banner of Arms, allows to postulate that its manufacture process was done in Europe employing precious materials to obtain a long-life object with a deep message for its viewers. Also, the data obtained helps to support the possible idea that the object was employed by Francisco Pizarro in the Peru conquest process. However, by the symbols present in the object, its elaboration date and materials, this object its clearly unique in its kind, and the most important, by its linguistic message, does not represent to Francisco Pizarro or his army, meanwhile, represents the Spanish crown. Therefore, instead to be labeled as Francisco Pizarro’s Banner of Arms, it should be called the Colonial Royal Banner of Charles V in the New World; RESUMEN: El estudio de textiles es un área abierta de investigación científica, la cual por su variedad de componentes materiales y la diversidad de condiciones físico-químicas presentes en estos objetos, lo hace un campo de interés para estudios científicos en el patrimonio cultural. Los textiles arqueológicos/históricos brindan la posibilidad de realizar estudios en materiales orgánicos como fibras, elementos de adhesión, tinturas, papel, etc., e inorgánicos como metales, aleaciones, piedras preciosas y demás materiales decorativos añadidos. Por su variedad de composición, es posible emplear diversas técnicas analíticas para resolver aquellas preguntas propias del objeto en una investigación arqueométrica. Uno de los objetos textiles que brinda gran información cultural debido a su representación lingüística empleada por las sociedades portadoras, son las banderas/estandartes/emblemas. Donde varía dependiendo de su uso y/o propósito, los materiales empleados en su elaboración, al igual que su iconografía (estilo, color, emblema, forma). El estudio de estos objetos construidos con un propósito de comunicación no verbal, da la posibilidad de extraer información a través de sus materiales y técnicas de elaboración sobre un rango temporal-espacial, un evento determinado en la historia o incluso a un personaje en específico. Las banderas han sido empleadas desde el siglo XI como objetos representativos de poder, jerarquía, organización social o militar, o como medio de comunicación. El uso de estos objetos se ha extendido a lo largo del mundo posiblemente debido a su fácil interpretación y/o apropiación por distintas sociedades, haciéndolo parte de su cultura. Las banderas como símbolos de control territorial, empleando símbolos que representan a una familia, orden o armada fueron introducidas a el Nuevo Mundo (América) con la llegada de los conquistadores europeos al final del siglo XV. Las banderas/estandartes que representaban el dominio Real sobre territorios dominados, la iglesia católica y las banderas de ejércitos y/o conquistadores fueron las primeras en llegar al nuevo mundo. Una de aquellas banderas que ha soportado el paso del tiempo, teniendo un gran valor cultural tanto para las sociedades americanas como para las ibéricas, es el denominado Estandarte de armas de Francisco Pizarro. Siendo un objeto textil con decoración en hilos metálicos sobre un emblema Real. De acuerdo a fuentes históricas, este objeto fue usado por Francisco Pizarro en 1532 en el proceso de conquista del Perú, quien recibe por parte del Rey Carlos V el poder para que, en su nombre, Pizarro pueda conquistar las tierras del nuevo mundo hoy conocidas como Perú. Luego del dominio de Pizarro sobre el territorio Inca, se cree que Pizarro dejó su estandarte en la cima del templo Inca del sol como símbolo de su control. Siglos más tarde, en las campañas libertarias de América, el General Sucre, militar encargado de la armada independentista en Perú, reporta haber encontrado lo que él considera como el estandarte de Pizarro, enviándolo a Bogotá como muestra de victoria, siendo custodiada desde ese momento por el Museo Nacional de Colombia hasta la actualidad. Debido a discrepancias históricas, el verdadero significado del llamado estandarte de Pizarro ha sido objeto de discusión y debido del pasar del tiempo su estado de conservación se ha deteriorado. Dejando de este modo, un caso de estudio interesante para que por medio de estudios científicos al objeto se pueda dar respuesta a preguntas tanto históricas como de conservación del mismo. De este modo, por medio de una colaboración con el Museo Nacional de Colombia, se obtuvo un juego de 25 muestras del llamado Estandarte de armas de Francisco Pizarro, abarcando los diferentes componentes y áreas del objeto de estudio. Dichas muestras fueron sometidas a estudios analíticos para su caracterización físico-química. Análisis de observación al microscopio, análisis VSEM-EDS, espectroscopia Raman, análisis cromatográficos (HPLC-MS, GC-MS) y datación por radiocarbono catorce fueron realizados. Del mismo modo, por medio de una inspección física al objeto in situ y una profunda investigación en fuentes históricas del mismo, se buscó la información adecuada para resolver sus problemáticas. Los resultados obtenidos permitieron identificar como seda el textil empleado en la elaboración del estandarte, así como el uso de colorantes naturales para teñir las fibras en el emblema: uso de cochinilla y palo de Brasil como fuente del color rojo, plantas a base de luteolin para el color amarillo, plantas a base de indigotina para el color azul y mezcla de colorantes amarillos y azules para el color verde fueron identificadas. Del mismo modo se evidencio el uso de adhesivos animales y el uso de papel de trapos en el proceso de manufactura. El estudio de los hilos metálicos, permitió evidenciar el uso de alambres con núcleos de plata con un fino recubrimiento de oro en su exterior, siendo aplanados y entrelazados con hilos de seda para su uso. Finalmente usando la datación por radiocarbono, fue posible conocer con alta precisión que el estandarte fue elaborado entre los siglos XV-XVI y sufrió procesos de restauración con añadidura de textiles en tiempos modernos. Junto a lo anterior, es posible postular que el estado de degradación de la tela es debido a degradación natural en las fibras de seda, teniendo así que su color se ha desvanecido y sus propiedades mecánicas disminuidas, conllevando a perdida de rigidez y desaparición de la estructura. Del mismo modo se pudo conocer los colores originales del emblema y evidenciar problemas de desprendimiento del papel debido a cristalización del adhesivo. Asimismo, se comprobó que los hilos metálicos presentan corrosión por azufre y desprendimiento de sus cristales. Finalmente, combinando los resultados analíticos y la información de fuentes históricas encontradas del llamado Estandarte de armas de Francisco Pizarro, se puede postular que su elaboración fue realizada en Europa, usando materiales preciosos para obtener un objeto de larga vida con un profundo mensaje para sus observadores. También, los datos obtenidos ayudan a dar soporte la posible idea de que este objeto fue usado por Francisco Pizarro en el proceso de conquista del Perú. Sin embargo, debido a los símbolos presentes en el objeto, fecha y materiales de elaboración, este objeto es claramente único en su tipo, y lo más importante, por su mensaje lingüístico, este no representa a Francisco Pizarro o su armada, al contrario, representa a la Corona de España. Por ende, en vez de denominarse como Estandarte de armas de Francisco Pizarro, este objeto debería nombrarse como el Estandarte Real de la Colonia de Carlos V en el Nuevo Mundo.

Development of Core Design Methods and Tools for Gen-IV Heavy Liquid Metal Cooled Reactors

Heavy Liquid Metal Cooled Reactors are among the concepts, fostered by the GIF, as potentially able to comply with stringent safety, economical, sustainability, proliferation resistance and physical protection requirements. The increasing interest around these innovative systems has highlighted the lack of tools specifically dedicated to their core design stage. The present PhD thesis summarizes the three years effort of, partially, closing the mentioned gap, by rationally defining the role of codes in core design and by creating a development methodology for core design-oriented codes (DOCs) and its subsequent application to the most needed design areas. The covered fields are, in particular, the fuel assembly thermal-hydraulics and the fuel pin thermo-mechanics. Regarding the former, following the established methodology, the sub-channel code ANTEO+ has been conceived. Initially restricted to the forced convection regime and subsequently extended to the mixed one, ANTEO+, via a thorough validation campaign, has been demonstrated a reliable tool for design applications. Concerning the fuel pin thermo-mechanics, the will to include safety-related considerations at the outset of the pin dimensioning process, has given birth to the safety-informed DOC TEMIDE. The proposed DOC development methodology has also been applied to TEMIDE; given the complex interdependence patterns among the numerous phenomena involved in an irradiated fuel pin, to optimize the code final structure, a sensitivity analysis has been performed, in the anticipated application domain. The development methodology has also been tested in the verification and validation phases; the latter, due to the low availability of experiments truly representative of TEMIDE's application domain, has only been a preliminary attempt to test TEMIDE's capabilities in fulfilling the DOC requirements upon which it has been built. In general, the capability of the proposed development methodology for DOCs in delivering tools helping the core designer in preliminary setting the system configuration has been proven.

Experimental determination of burning velocity in metal dust explosions

The modeling of metal dust explosion phenomenon is important in order to safeguard industries from potential accidents. A key parameter of these models is the burning velocity, which represents the consumption rate of the reactants by the flame front, during the combustion process. This work is focused on the experimental determination of aluminium burning velocity, through an alternative method, called "Direct method". The study of the methods used and the results obtained is preceded by a general analysis on dust explosion phenomenon, flame propagation phenomenon, characteristics of the metals combustion process and standard methods for determining the burning velocity. The “Direct method” requires a flame propagating through a tube recorded by high-speed cameras. Thus, the flame propagation test is carried out inside a vertical prototype made of glass. The study considers two optical technique: the direct visualization of the light emitted by the flame and the Particle Image Velocimetry (PIV) technique. These techniques were used simultaneously and allow the determination of two velocities: the flame propagation velocity and the flow velocity of the unburnt mixture. Since the burning velocity is defined by these two quantities, its direct determination is done by substracting the flow velocity of the fresh mixture from the flame propagation velocity. The results obtained by this direct determination, are approximated by a linear curve and different non-linear curves, which show a fluctuating behaviour of burning velocity. Furthermore, the burning velocity is strongly affected by turbulence. Turbulence intensity can be evaluated from PIV technique data. A comparison between burning velocity and turbulence intensity highlighted that both have a similar trend.

Simulation of photoinduced processes in organic chromophores: mapping photochemically relevant states for accurate dynamics

The simulation of ultrafast photoinduced processes is a fundamental step towards the understanding of the underlying molecular mechanism and interpretation/prediction of experimental data. Performing a computer simulation of a complex photoinduced process is only possible introducing some approximations but, in order to obtain reliable results, the need to reduce the complexity must balance with the accuracy of the model, which should include all the relevant degrees of freedom and a quantitatively correct description of the electronic states involved in the process. This work presents new computational protocols and strategies for the parameterisation of accurate models for photochemical/photophysical processes based on state-of-the-art multiconfigurational wavefunction-based methods. The required ingredients for a dynamics simulation include potential energy surfaces (PESs) as well as electronic state couplings, which must be mapped across the wide range of geometries visited during the wavepacket/trajectory propagation. The developed procedures allow to obtain solid and extended databases reducing as much as possible the computational cost, thanks to, e.g., specific tuning of the level of theory for different PES regions and/or direct calculation of only the needed components of vectorial quantities (like gradients or nonadiabatic couplings). The presented approaches were applied to three case studies (azobenzene, pyrene, visual rhodopsin), all requiring an accurate parameterisation but for different reasons. The resulting models and simulations allowed to elucidate the mechanism and time scale of the internal conversion, reproducing or even predicting new transient experiments. The general applicability of the developed protocols to systems with different peculiarities and the possibility to parameterise different types of dynamics on an equal footing (classical vs purely quantum) prove that the developed procedures are flexible enough to be tailored for each specific system, and pave the way for exact quantum dynamics with multiple degrees of freedom.

Development of a numerical platform for the modeling and optimal control of liquid metal flows

The main purpose of this work is to develop a numerical platform for the turbulence modeling and optimal control of liquid metal flows. Thanks to their interesting thermal properties, liquid metals are widely studied as coolants for heat transfer applications in the nuclear context. However, due to their low Prandtl numbers, the standard turbulence models commonly used for coolants as air or water are inadequate. Advanced turbulence models able to capture the anisotropy in the flow and heat transfer are then necessary. In this thesis, a new anisotropic four-parameter turbulence model is presented and validated. The proposed model is based on explicit algebraic models and solves four additional transport equations for dynamical and thermal turbulent variables. For the validation of the model, several flow configurations are considered for different Reynolds and Prandtl numbers, namely fully developed flows in a plane channel and cylindrical pipe, and forced and mixed convection in a backward-facing step geometry. Since buoyancy effects cannot be neglected in liquid metals-cooled fast reactors, the second aim of this work is to provide mathematical and numerical tools for the simulation and optimization of liquid metals in mixed and natural convection. Optimal control problems for turbulent buoyant flows are studied and analyzed with the Lagrange multipliers method. Numerical algorithms for optimal control problems are integrated into the numerical platform and several simulations are performed to show the robustness, consistency, and feasibility of the method.

Optoelectronic investigation of defects in hybrid metal halide perovskites

The growing demand for flexible and low-cost electronics has driven research towards the study of novel semiconducting materials to replace traditional semiconductors like silicon and germanium, which are limited by mechanical rigidity and high production cost. Some of the most promising semiconductors in this sense are metal halide perovskites (MHPs), which combine low-cost fabrication and solution processability with exceptional optoelectronic properties like high absorption coefficient, long charge carrier lifetime, and high mobility. These properties, combined with an impressive effort by many research groups around the world, have enabled the fabrication of solar cells with record-breaking efficiencies, and photodetectors with better performance than commercial ones. However, MHP devices are still affected by issues that are hindering their commercialization, such as degradation under humidity and illumination, ion migration, electronic defects, and limited resistance to mechanical stress. The aim of this thesis work is the experimental characterization of these phenomena. We investigated the effects of several factors, such as X-ray irradiation, exposure to environmental gases, and atmosphere during synthesis, on the optoelectronic properties of MHP single crystals. We achieved this by means of optical spectroscopy, electrical measurements, and chemical analyses. We identified the cause of mechanical delamination in MHP/silicon tandem solar cells by atomic force microscopy measurements. We characterized electronic defects and ion migration in MHP single crystals by applying for the first time the photo-induced current transient spectroscopy technique to this class of materials. This research allowed to gain insight into both intrinsic defects, like ion migration and electron trapping, and extrinsic defects, induced by X-ray irradiation, mechanical stress, and exposure to humidity. This research paves the way to the development of methods that heal and passivate these defects, enabling improved performance and stability of MHP optoelectronic devices.

In-car sound linear simulation

In recent years, vehicle acoustics have gained significant importance in new car development: increasingly advanced infotainment systems for spatial audio and sound enhancement algorithms have become the norm in modern vehicles. In the past, car manufacturers had to build numerous prototypes to study the sound behaviour inside the car cabin or the effect of new algorithms under development. Nowadays, advanced simulation techniques can reduce development costs and time. In this work, after selecting the reference test vehicle, a modern luxury sedan equipped with a high-end sound system, two independent tools were developed: a simulation tool created in the Comsol Multiphysics environment and an auralization tool developed in the Cycling ‘74 MAX environment. The simulation tool can calculate the impulse response and acoustic spectrum at a specific position inside the cockpit. Its input data are the vehicle’s geometry, acoustic absorption parameters of materials, the acoustic characteristics and position of loudspeakers, and the type and position of virtual microphones (or microphone arrays). The simulation tool can also provide binaural impulse responses thanks to Head Related Transfer Functions (HRTFs) and an innovative algorithm able to compute the HRTF at any distance and angle from the head. Impulse responses from simulations or acoustic measurements inside the car cabin are processed and fed into the auralization tool, enabling real-time interaction by applying filters, changing the channels gain or displaying the acoustic spectrum. Since the acoustic simulation of a vehicle involves multiple topics, the focus of this work has not only been the development of two tools but also the study and application of new techniques for acoustic characterization of the materials that compose the cockpit and the loudspeaker simulation. Specifically, three different methods have been applied for material characterization through the use of a pressure-velocity probe, a Laser Doppler Vibrometer (LDV), and a microphone array.

Fabrication of 2D and 3D microelectrode arrays for amperometric dopamine sensing: towards a metal free approach to bioelectronics

Dopamine is a neurotransmitter which has a role in several psychiatric and neurological disorders. In-vivo detection of its concentration at the microscopic scale would benefit the study of these conditions and help in the development of therapies. The ideal sensor would be biocompatible, able to probe concentrations in microscopic volumes and sensitive to the small physiological concentrations of this molecule (10 nM - 1 μM). The ease of oxidation of dopamine makes it possible to detect it by electrochemical methods. An additional requirement in this kind of experiments when run in water, though, is to have a large potential window inside which no redox reactions with water take place. A promising class of materials which are being explored is the one of pyrolyzed photoresists. Photoresists can be lithographically patterned with micrometric resolution and after pyrolysis leave a glassy carbon material which is conductive, biocompatible and has a large electrochemical water window. In this work I developed a fabrication procedure for microelectrode arrays with three dimensional electrodes, making the whole device using just a negative photoresist called SU8. Making 3D electrodes could be a way to enhance the sensitivity of the electrodes without occupying a bigger footprint on the device. I characterized the electrical, morphological, and electrochemical properties of these electrodes, in particular their sensitivity to dopamine. I also fabricated and tested a two dimensional device for comparison. The three dimensional devices fabricated showed inferior properties to their two dimensional counter parts. I found a possible explanation and suggested some ways in which the fabrication could be improved.

Classification Of Frankfurters By Ft-raman Spectroscopy And Chemometric Methods.

Frankfurters are widely consumed all over the world, and the production requires a wide range of meat and non-meat ingredients. Due to these characteristics, frankfurters are products that can be easily adulterated with lower value meats, and the presence of undeclared species. Adulterations are often still difficult to detect, due the fact that the adulterant components are usually very similar to the authentic product. In this work, FT-Raman spectroscopy was employed as a rapid technique for assessing the quality of frankfurters. Based on information provided by the Raman spectra, a multivariate classification model was developed to identify the frankfurter type. The aim was to study three types of frankfurters (chicken, turkey and mixed meat) according to their Raman spectra, based on the fatty vibrational bands. Classification model was built using partial least square discriminant analysis (PLS-DA) and the performance model was evaluated in terms of sensitivity, specificity, accuracy, efficiency and Matthews's correlation coefficient. The PLS-DA models give sensitivity and specificity values on the test set in the ranges of 88%-100%, showing good performance of the classification models. The work shows the Raman spectroscopy with chemometric tools can be used as an analytical tool in quality control of frankfurters.

Survival Extrapolation In The Presence Of Cause Specific Hazards.

Health economic evaluations require estimates of expected survival from patients receiving different interventions, often over a lifetime. However, data on the patients of interest are typically only available for a much shorter follow-up time, from randomised trials or cohorts. Previous work showed how to use general population mortality to improve extrapolations of the short-term data, assuming a constant additive or multiplicative effect on the hazards for all-cause mortality for study patients relative to the general population. A more plausible assumption may be a constant effect on the hazard for the specific cause of death targeted by the treatments. To address this problem, we use independent parametric survival models for cause-specific mortality among the general population. Because causes of death are unobserved for the patients of interest, a polyhazard model is used to express their all-cause mortality as a sum of latent cause-specific hazards. Assuming proportional cause-specific hazards between the general and study populations then allows us to extrapolate mortality of the patients of interest to the long term. A Bayesian framework is used to jointly model all sources of data. By simulation, we show that ignoring cause-specific hazards leads to biased estimates of mean survival when the proportion of deaths due to the cause of interest changes through time. The methods are applied to an evaluation of implantable cardioverter defibrillators for the prevention of sudden cardiac death among patients with cardiac arrhythmia. After accounting for cause-specific mortality, substantial differences are seen in estimates of life years gained from implantable cardioverter defibrillators.

Modelagem matemática e simulação numérica do resfriamento rápido de morango com ar forçado

This work approaches the forced air cooling of strawberry by numerical simulation. The mathematical model that was used describes the process of heat transfer, based on the Fourier's law, in spherical coordinates and simplified to describe the one-dimensional process. For the resolution of the equation expressed for the mathematical model, an algorithm was developed based on the explicit scheme of the numerical method of the finite differences and implemented in the scientific computation program MATLAB 6.1. The validation of the mathematical model was made by the comparison between theoretical and experimental data, where strawberries had been cooled with forced air. The results showed to be possible the determination of the convective heat transfer coefficient by fitting the numerical and experimental data. The methodology of the numerical simulations was showed like a promising tool in the support of the decision to use or to develop equipment in the area of cooling process with forced air of spherical fruits.

Abrasion wear resistance of different artificial teeth opposed to metal and composite antagonists

One of the most important properties of artificial teeth is the abrasion wear resistance, which is determinant in the maintenance of the rehabilitation's occlusal pattern. OBJECTIVES: This in vitro study aims to evaluate the abrasion wear resistance of 7 brands of artificial teeth opposed to two types of antagonists. MATERIAL AND METHODS: Seven groups were prepared with 12 specimens each (BIOLUX & BL, TRILUX & TR, BLUE DENT & BD, BIOCLER & BC, POSTARIS & PO, ORTHOSIT & OR, GNATHOSTAR & GN), opposed to metallic (M & nickel-chromium alloy), and to composite antagonists (C & Solidex indirect composite). A mechanical loading device was used (240 cycles/min, 4 Hz speed, 10 mm antagonist course). Initial and final contours of each specimen were registered with aid of a profile projector (20x magnification). The linear difference between the two profiles was measured and the registered values were subjected to ANOVA and Tukey's test. RESULTS: Regarding the antagonists, only OR (M = 10.45 ± 1.42 µm and C = 2.77 ± 0.69 µm) and BC (M = 6.70 ± 1.37 µm and C = 4.48 ± 0.80 µm) presented statistically significant differences (p < 0.05). Best results were obtained with PO (C = 2.33 ± 0.91 µm and M = 1.78 ± 0.42 µm), followed by BL (C = 3.70 ± 1.32 µm and M = 3.70 ± 0.61 µm), statistically similar for both antagonists (p>0.05). Greater result variance was obtained with OR, which presented the worse results opposed to Ni-Cr (10.45 ± 1.42 µm), and results similar to the best ones against composite (2.77 ± 0.69 µm). CONCLUSIONS: Within the limitations of this study, it may be concluded that the antagonist material is a factor of major importance to be considered in the choice of the artificial teeth to be used in the prosthesis.

Comparative study of two commercially pure titanium casting methods

The interest in using titanium to fabricate removable partial denture (RPD) frameworks has increased, but there are few studies evaluating the effects of casting methods on clasp behavior. OBJECTIVE: This study compared the occurrence of porosities and the retentive force of commercially pure titanium (CP Ti) and cobalt-chromium (Co-Cr) removable partial denture circumferential clasps cast by induction/centrifugation and plasma/vacuum-pressure. MATERIAL AND METHODS: 72 frameworks were cast from CP Ti (n=36) and Co-Cr alloy (n=36; control group). For each material, 18 frameworks were casted by electromagnetic induction and injected by centrifugation, whereas the other 18 were casted by plasma and injected by vacuum-pressure. For each casting method, three subgroups (n=6) were formed: 0.25 mm, 0.50 mm, and 0.75 mm undercuts. The specimens were radiographed and subjected to an insertion/removal test simulating 5 years of framework use. Data were analyzed by ANOVA and Tukey's to compare materials and cast methods (α=0.05). RESULTS: Three of 18 specimens of the induction/centrifugation group and 9 of 18 specimens of plasma/vacuum-pressure cast presented porosities, but only 1 and 7 specimens, respectively, were rejected for simulation test. For Co-Cr alloy, no defects were found. Comparing the casting methods, statistically significant differences (p<0.05) were observed only for the Co-Cr alloy with 0.25 mm and 0.50 mm undercuts. Significant differences were found for the 0.25 mm and 0.75 mm undercuts dependent on the material used. For the 0.50 mm undercut, significant differences were found when the materials were induction casted. CONCLUSION: Although both casting methods produced satisfactory CP Ti RPD frameworks, the occurrence of porosities was greater in the plasma/vacuum-pressure than in the induction/centrifugation method, the latter resulting in higher clasp rigidity, generating higher retention force values.