Settlement Of Reinforced Sand In Foundations

The technique of reinforcing soil for foundation improvement is well established. This paper addresses the aspect of settlement of reinforced sand foundations, where the major part of the existing work deals with the aspect of bearing capacity. A detailed analysis is made paying individual attention to soil, reinforcement, and the interface between the two. A three-dimensional, nonlinear finite-element analysis is presented that uses a three-dimensional, nonlinear soil-reinforcement interface friction element, along with other threedimensional elements to model the system. The results of the analysis are compared with those from tests conducted in the laboratory and are found to be in good agreement. The studies lead to a better understanding of the behavior of the system at different stages of loading

Cure Kinetics and Sorption Characteristics of Neoprene-Based Rubber Ferrite Composites

Rubber ferrite composites were prepared by incorporating nickel ferrite in a neoprene rubber matrix. Kinetics of the cure reaction were determined from the rheometric torque values and found to follow first-order kinetics. Analysis of the swelling behavior of the rubber ferrite composites in toluene elucidates the mechanism of solvent penetration and sorption characteristics, and reveals the extent of the physical interaction of the ferrite particles with the neoprene rubber matrix. Mechanical properties of rubber ferrite composites were determined, which support the reinforcing nature of nickel ferrite to the neoprene rubber matrix. These results show that magnetic composites with the required processing safety can be prepared economically by incorporating higher amounts of nickel ferrite in the neoprene rubber matrix

Performance of hybrid rebars as longitudinal reinforcement in normal strength concrete

A/though steel is most commonly used as a reinforcing material in concrete due to its competitive cost and favorable mechanical properties, the problem of corrosion of steel rebars leads to a reduction in life span of the structure and adds to maintenance costs. Many techniques have been developed in recent past to reduce corrosion (galvanizing, epoxy coating, etc.) but none of the solutions seem to be viable as an adequate solution to the corrosion problem. Apart from the use of fiber reinforced polymer (FRP) rebars, hybrid rebars consisting of both FRP and steel are also being tried to overcome the problem of steel corrosion. This paper evaluates the performance of hybrid rebars as longitudinal reinforcement in normal strength concrete beams. Hybrid rebars used in this study essentially consist of glass fiber reinforced polymer (GFRP) strands of 2 mm diameter wound helically on a mild steel core of 6 mm diameter. GFRP stirrups have been used as shear reinforcement. An attempt has been made to evaluate the flexural and shear performance of beams having hybrid rebars in normal strength concrete with and without polypropylene fibers added to the concrete matrix

Nonlinear Analysis of Shear Dominant Prestressed Concrete Beams using ANSYS

This study reports the details of the finite element analysis of eleven shear critical partially prestressed concrete T-beams having steel fibers over partial or full depth. Prestressed T-beams having a shear span to depth ratio of 2.65 and 1.59 that failed in shear have been analyzed using the ‘ANSYS’ program. The ‘ANSYS’ model accounts for the nonlinearity, such as, bond-slip of longitudinal reinforcement, postcracking tensile stiffness of the concrete, stress transfer across the cracked blocks of the concrete and load sustenance through the bridging action of steel fibers at crack interface. The concrete is modeled using ‘SOLID65’- eight-node brick element, which is capable of simulating the cracking and crushing behavior of brittle materials. The reinforcement such as deformed bars, prestressing wires and steel fibers have been modeled discretely using ‘LINK8’ – 3D spar element. The slip between the reinforcement (rebars, fibers) and the concrete has been modeled using a ‘COMBIN39’- nonlinear spring element connecting the nodes of the ‘LINK8’ element representing the reinforcement and nodes of the ‘SOLID65’ elements representing the concrete. The ‘ANSYS’ model correctly predicted the diagonal tension failure and shear compression failure of prestressed concrete beams observed in the experiment. The capability of the model to capture the critical crack regions, loads and deflections for various types of shear failures in prestressed concrete beam has been illustrated.

Rice husk ash – A valuable reinforcement for high density polyethylene

This paper presents the results of a study on the use of rice husk ash (RHA) for property modification of high density polyethylene (HDPE). Rice husk is a waste product of the rice processing industry. It is used widely as a fuel which results in large quantities of RHA. Here, the characterization of RHA has been done with the help of X-ray diffraction (XRD), Inductively Coupled Plasma Atomic Emission Spectroscopy (ICPAES), light scattering based particle size analysis, Fourier transform infrared spectroscopy (FTIR) and Scanning Electron Microscope (SEM). Most reports suggest that RHA when blended directly with polymers without polar groups does not improve the properties of the polymer substantially. In this study RHA is blended with HDPE in the presence of a compatibilizer. The compatibilized HDPE-RHA blend has a tensile strength about 18% higher than that of virgin HDPE. The elongation-at-break is also higher for the compatibilized blend. TGA studies reveal that uncompatibilized as well as compatibilized HDPERHA composites have excellent thermal stability. The results prove that RHA is a valuable reinforcing material for HDPE and the environmental pollution arising from RHA can be eliminated in a profitable way by this technique.

Microwave exfoliated reduced graphene oxide epoxy nanocomposites for high performance applications

Graphene has captured the attention of scientific community due to recently emerging high performance applications. Hence, studying its reinforcing effects on epoxy resin is a significant step. In this study, microwave exfoliated reduced graphene oxide (MERGO) was prepared from natural graphite for subsequent fabrication of epoxy nanocomposites using triethylenetetramine (TETA) as a curing agent via insitu polymerization. Thermogravimetric analysis (TGA), X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), C13 NMR spectroscopy, X-ray photoelectron spectroscopy (XPS) and ultravioletevisible (UVevis) spectroscopy were employed to confirm the simultaneous reduction and exfoliation of graphene oxide. The reinforcing effect of MERGO on epoxy resin was explored by investigating its static mechanical properties and dynamic mechanical analysis (DMA) at MERGO loadings of 0 to 0.5 phr. The micro-structure of epoxy/MERGO nanocomposites was investigated using scanning electron microscope (SEM), transmission electron microscope (TEM) and XRD techniques. The present work reports an enhancement of 32%, 103% and 85% in tensile, impact and flexural strength respectively of epoxy by the addition of even 0.25 phr MERGO. At this loading elastic and flexural moduli also increased by 10% and 65%, respectively. Single-edge-notch three-point-Bending (SEN-TPB) fracture toughness (KIC) measurements were carried out where a 63% increase was observed by the introduction of 0.25 phr MERGO. The interfacial interactions brought about by graphene also benefited the dynamic mechanical properties to a large extent in the form of a significant enhancement in storage modulus and slightly improved glass transition temperature. Considerable improvements were also detected in dielectric properties. The epoxy nanocomposite also attained an ac conductivity of 10 5 S/m and a remarkable increase in dielectric constant. The simple and cost effective way of graphene synthesis for the fabrication of epoxy/MERGO nanocomposites may be extended to the preparation of other MERGO based polymer nanocomposites. This remarkable class of materials has thrown open enormous opportunities for developing conductive adhesives and in microelectronics

HDPE-Ash Nanocomposites

Ash-based polymer composites are assuming increasing importance because of the pollutant potential, fine particle size, and low price of ash. Fly ash and rice husk ash are two prominent ash materials on which some investigations have already been done for potential use in polymer composites. This article highlights the results of a study on the use of wood ash in HDPE. Wood ash is mainly a mixture of various metallic compounds and some silica. Here, the characterization of wood ash has been done with the help of XRD, ICPAES, light scattering based particle size analysis, FTIR, and SEM. The results show that wood ash particle size has an average value of 293 nm, much lower than other categories of ash. When blended with HDPE in the presence of a compatibilizer, wood ash gives rise to vastly improved mechanical properties over that of the base polymer. The results prove that wood ash is a valuable reinforcing material for HDPE and the environmental pollution due to wood ash can be solved in a most profitable way by this technique.

Studies on the use of Nanokaolin, MWCNT and Graphene in NBR and SBR

The current research investigates the possibility of using unmodified and modified nanokaolin, multiwalled carbon nanotube (MWCNT) and graphene as fillers to impart enhancement in mechanical, thermal, and electrical properties to the elastomers. Taking advantage of latex blending method, nanoclay, MWCNT and graphene dispersions, prepared by ultra sound sonication are dispersed in polymer latices. The improvement in material properties indicated better interaction between filler and the polymer.MWCNT and graphene imparted electrical conductivity with simultaneous improvement in mechanical properties. Layered silicates prepared by microwave method also significantly improve the mechanical properties of the nanocomposites. The thesis entitled ‘Studies on the use of Nanokaolin, MWCNT and Graphene in NBR and SBR’ consists of ten chapters. The first chapter is a concise introduction of nanocomposites, nanofillers, elastomeric matrices and applications of polymer nanocomposites. The state-of-art research in elastomer based nanocomposites is also presented. At the end of this chapter the main objectives of the work are mentioned. Chapter 2 outlines the specifications of various materials used, details of experimental techniques employed for preparing and characterizing nanocomposites. Chapter3 includes characterization of the nanofillers, optimsation of cure time of latex based composites and the methods used for the preparation of latex based and dry rubber based nanocomposites. Chapter4 presents the reinforcing effect of the nanofillers in XNBR latex and the characterization of the nanocomposites. Chapter5 comprises the effect of nanofillers on the properties of SBR latex and their characterization Chapter 6 deals with the study of cure characteristics, mechanical and thermal properties and the characterization of NBR based nanocomposites. Chapter7 is the microwave studies of MWCNT and graphene filled elastomeric nanocomposites. Chapter 8 gives details of the preparation of layered silicates, their characterization and use in different elastomeric matrices. Chapter 9 is the study of mechanical properties of nanoclay incorporated nitrile gloves .Chapter 10 presents the summary and conclusions of the investigation.

SHGs and Cooperatives in the Fishing Sector: An Inclusive Development Option for the Fisher folk of Kerala

The Kerala model of development mostly bypassed the fishing community, as the fishers form the main miserable groups with respect to many of the socio-economic and quality of life indicators. Modernization drive in the fishing sector paradoxically turns to marginalization drives as far as the traditional fishers in Kerala are concerned. Subsequent management and resource recuperation drives too seemed to be detrimental to the local fishing community. Though SHGs and cooperatives had helped in overcoming many of the maladies in most of the sectors in Kerala in terms of livelihood and employment in the 1980s, the fishing sector by that time had been moving ahead with mechanization and export euphoria and hence it bypassed the fishing sector. Though it has not helped the fishing sector in the initial stages, but because of necessity, it soon has become a vibrant livelihood and employment force in the coastal economy of Kerala. Initial success made it to link this with the governmental cooperative set up and soon SHGs and Cooperatives become reinforcing forces for the inclusive development of the real fishers.The fisheries sector in Kerala has undergone drastic changes with the advent of globalised economy. The traditional fisher folk are one of the most marginalized communities in the state and are left out of the overall development process mainly due to the marginalization of this community both in the sea and in the market due to modernization and mechanization of the sector. Mechanization opened up the sector a great deal as it began to attract people belonging to non-fishing community as moneylenders, boat owners, employers and middle men which often resulted in conflicts between traditional and mechanized fishermen. These factors, together with resource depletion resulted in the backwardness experienced by the traditional fishermen compared to other communities who were reaping the benefits of the overall development scenario.The studies detailing the activities and achievements of fisher folks via Self Help Groups (SHGs) and the cooperative movement in coastal Kerala are scant. The SHGs through cooperatives have been effective in livelihood security, poverty alleviation and inclusive development of the fisher folk (Rajasenan and Rajeev, 2012). The SHGs have a greater role to play as estimated fall in demand for marine products in international markets, which may result in reduction of employment opportunities in fish processing, peeling, etc. Also, technological advancement has made them unskilled to work in this sector making them outliers in the overall development process resulting in poor quality of physical and social infrastructure. Hence, it is all the more important to derive a strategy and best practice methods for the effective functioning of these SHGs so that the

Regional Labor Market Disparities

Regionale Arbeitsmärkte unterscheiden sich erheblich hinsichtlich wesentlicher Kennzahlen wie der Arbeitslosenquote, des Lohnniveaus oder der Beschäftigungsentwicklung. Wegen ihrer Persistenz sind diese Unterschiede von hoher Relevanz für die Politik. Die wirtschaftswissenschaftliche Literatur liefert bereits theoretische Modelle für die Analyse regionaler Arbeitsmärkte. In der Regel sind diese Modelle aber nicht dazu geeignet, regionale Arbeitsmarktunterschiede endogen zu erklären. Das bedeutet, dass sich die Unterschiede regionaler Arbeitsmärkte in der Regel nicht aus den Modellzusammenhängen selbst ergeben, sondern „von außen“ eingebracht werden müssen. Die empirische Literatur liefert Hinweise, dass die Unterschiede zwischen regionalen Arbeitsmärkten auf die Höhe der regionalen Arbeitsnachfrage zurückzuführen sind. Die Arbeitsnachfrage wiederum leitet sich aus den Gütermärkten ab: Es hängt von der Entwicklung der regionalen Gütermärkte ab, wie viele Arbeitskräfte benötigt werden. Daraus folgt, dass die Ursachen für Unterschiede regionaler Arbeitsmärkte in den Unterschieden zwischen den regionalen Gütermärkten zu suchen sind. Letztere werden durch die Literatur zur Neuen Ökonomischen Geographie (NÖG) untersucht. Die Literatur zur NÖG erklärt Unterschiede regionaler Gütermärkte, indem sie zentripetale und zentrifugale Kräfte gegenüberstellt. Zentripetale Kräfte sind solche, welche hin zur Agglomeration ökonomischer Aktivität wirken. Im Zentrum dieser Diskussion steht vor allem das Marktpotenzial: Unternehmen siedeln sich bevorzugt an solchen Standorten an, welche nahe an großen Märkten liegen. Erwerbspersonen wiederum bevorzugen solche Regionen, welche ihnen entsprechende Erwerbsaussichten bieten. Beides zusammen bildet einen sich selbst verstärkenden Prozess, der zur Agglomeration ökonomischer Aktivität führt. Dem stehen jedoch zentrifugale Kräfte gegenüber, welche eine gleichmäßigere Verteilung ökonomischer Aktivität bewirken. Diese entstehen beispielsweise durch immobile Produktionsfaktoren oder Ballungskosten wie etwa Umweltverschmutzung, Staus oder hohe Mietpreise. Sind die zentripetalen Kräfte hinreichend stark, so bilden sich Zentren heraus, in denen sich die ökonomische Aktivität konzentriert, während die Peripherie ausdünnt. In welchem Ausmaß dies geschieht, hängt von dem Verhältnis beider Kräfte ab. Üblicherweise konzentriert sich die Literatur zur NÖG auf Unterschiede zwischen regionalen Gütermärkten und geht von der Annahme perfekter Arbeitsmärkte ohne Arbeitslosigkeit aus. Die Entstehung und Persistenz regionaler Arbeitsmarktunterschiede kann die NÖG daher üblicherweise nicht erklären. An dieser Stelle setzt die Dissertation an. Sie erweitert die NÖG um Friktionen auf dem Arbeitsmarkt, um die Entstehung und Persistenz regionaler Arbeitsmarktunterschiede zu erklären. Sie greift dazu auf eine empirische Regelmäßigkeit zurück: Zahlreiche Studien belegen einen negativen Zusammenhang zwischen Lohn und Arbeitslosigkeit. In Regionen, in denen die Arbeitslosigkeit hoch ist, ist das Lohnniveau gering und umgekehrt. Dieser Zusammenhang wird als Lohnkurve bezeichnet. Auf regionaler Ebene lässt sich die Lohnkurve mithilfe der Effizienzlohntheorie erklären, die als theoretische Grundlage in der Dissertation Anwendung findet. Konzentriert sich nun die ökonomische Aktivität aufgrund der zentripetalen Kräfte in einer Region, so ist in diesem Zentrum die Arbeitsnachfrage höher. Damit befindet sich das Zentrum auf einer günstigen Position der Lohnkurve mit geringer Arbeitslosigkeit und hohem Lohnniveau. Umgekehrt findet sich die Peripherie auf einer ungünstigen Position mit hoher Arbeitslosigkeit und geringem Lohnniveau wieder. Allerdings kann sich die Lohnkurve in Abhängigkeit des Agglomerationsgrades verschieben. Das komplexe Zusammenspiel der endogenen Agglomeration mit den Arbeitsmarktfriktionen kann dann unterschiedliche Muster regionaler Arbeitsmarktdisparitäten hervorrufen. Die Dissertation zeigt auf, wie im Zusammenspiel der NÖG mit Effizienzlöhnen regionale Arbeitsmarktdisparitäten hervorgerufen werden. Es werden theoretische Modelle formuliert, die diese Interaktionen erklären und welche die bestehende Literatur durch spezifische Beiträge erweitern. Darüber hinaus werden die zentralen Argumente der Theorie einem empirischen Test unterworfen. Es kann gezeigt werden, dass das zentrale Argument – der positive Effekt des Marktpotentials auf die Arbeitsnachfrage – relevant ist. Außerdem werden Politikimplikationen abgeleitet und der weitere Forschungsbedarf aufgezeigt.

Investigating shape representation in area V4 with HMAX: Orientation and Grating selectivities

The question of how shape is represented is of central interest to understanding visual processing in cortex. While tuning properties of the cells in early part of the ventral visual stream, thought to be responsible for object recognition in the primate, are comparatively well understood, several different theories have been proposed regarding tuning in higher visual areas, such as V4. We used the model of object recognition in cortex presented by Riesenhuber and Poggio (1999), where more complex shape tuning in higher layers is the result of combining afferent inputs tuned to simpler features, and compared the tuning properties of model units in intermediate layers to those of V4 neurons from the literature. In particular, we investigated the issue of shape representation in visual area V1 and V4 using oriented bars and various types of gratings (polar, hyperbolic, and Cartesian), as used in several physiology experiments. Our computational model was able to reproduce several physiological findings, such as the broadening distribution of the orientation bandwidths and the emergence of a bias toward non-Cartesian stimuli. Interestingly, the simulation results suggest that some V4 neurons receive input from afferents with spatially separated receptive fields, leading to experimentally testable predictions. However, the simulations also show that the stimulus set of Cartesian and non-Cartesian gratings is not sufficiently complex to probe shape tuning in higher areas, necessitating the use of more complex stimulus sets.

Portal web per la localitzacó de restaurants

Desenvolupament,anàlisi, disseny i implementació d’un portal web, tipus cercador, per la recerca i localització d’establiments tipus restaurant, bars, bufets, etc,. Per altra banda es pretén oferir un sistema de gestió d’informació on les empreses del sector gastronòmic puguin mostrar la seva informació i la seva oferta

Efectos de un programa de intervención individualizado de fomento de la competencia lectora en alumnos inmigrantes y con dificultades de aprendizaje del primer ciclo de la ESO : un estudio piloto.

Seleccionado en la convocatoria: Concurso de proyectos de cooperación en materia de investigación entre departamentos universitarios y departamentos de Institutos de Educación Secundaria o equipos de personal docente, Gobierno de Aragón 2010-2011

Una de llibres!

S'acosta la primavera i el sol comença a escalfar les taules i les cadires a les terrasses dels bars, que s'omplen de gent. I els cambrers van servint les tapes, les cerveses, els martinis ben fresquets... La revista Engega us vol fer de cambrer i us porta a la taula uns quants títols que no són sinó un aperitiu de tot el que conté la carta d'aquesta mena de local fantàstic que és la Universitat de Girona. Feu-los servir com millor us vingui de gust. Feu veure que el de poesia és el vermut i el d'història les olives i, un de filosofia, encara, les patates fregides. I quan després us vingui de gust dinar, demaneu la carta, que a la cuina, volem dir a les biblioteques, tenim tot el que és necessari per fer-vos passar la gana

Autoclau pel processament de materials compòsits

Disseny d’un autoclau pel processat de materials compòsits, seguint les especificacions de disseny següents: Diàmetre interior útil: 1500mm, Longitud interior útil 3500mm, Pressió de treball: 12 bars, Temperatura de treball: 250º. A més a més, el sistema ha de disposar en el seu interior de connexions per fer el buit i s’ha d’assegurar l’homogeneïtat tèrmica recirculant l’aire durant el procés