Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.

Sisäilman laatuun vaikuttavat tekijät ja siivouskäytäntöjen laadunvarmistus

Sisäilman laatuun vaikuttaa moni eri tekijä. Sisäilma on tavallisesti laadultaan hyvää silloin, kun tilojen käyttäjät ovat siihen tyytyväisiä. Hyvän sisäilman saavuttamiseksi tulee ilmanvaihdon, lämmityslaitteiden, siivouksen ja talon rakenteiden olla kunnossa. Tämä työ on tehty Helsingin kaupungin Tilakeskukselle, ja se on osa vuoden jatkuvaa projektia, jossa selvitetään siivouksen riittävyyttä ja sen vaikutusta koulujen sisäilmaan. Työn tavoitteena on luoda siivouksen laadunvarmistusmenetelmä, jonka avulla voidaan varmistaa toteutunut siivouksen taso. Lisäksi projektissa selvitetään, pystytäänkö siivouksen palvelusopimus toteuttamaan käytännössä kunnolla. Työssä kehitettävät menetelmät ovat subjektiivinen ja objektiivinen pölyisyyden arviointi sekä kyselylomake koulujen opettajille. Työssä kehitetyn menetelmän laatutasojen raja-arvot noudattavat INSTA 800 -standardissa esitettäviä arvoja. Kehitettyä menetelmää käytettiin suoritetuissa lähtö- ja nollatasomittauksissa. Mittauksista saadut tulokset vastasivat silmämääräisesti tiloissa tehtyjä havaintoja.

Reduction of nitrogen oxide emissions in lime kiln

Different nitrogen oxide removal technologies for rotary lime kiln are studied in this thesis, the main focus being in commercial technologies. Post-combustion methods are investigated in more detail as potential possible NOx removal with combustion methods in rotary lime kiln is more limited or primary methods are already in use. However, secondary methods as NOx scrubber, SNCR or SCR technologies are not listed as the Best Available Technologies defined by European Union. BAT technologies for NOx removal in lime kiln are (1) Optimised combustion and combustion control, (2) Good mixing of fuel and air, (3) Low-NOx burner and (4) Fuel selection/low-N fuel. SNCR method is the most suitable technique for NOx removal in lime kiln when NOx removal from 50 % to 70 % is required in case primary methods are already in use or cannot be applied. In higher removal cases ammonia slip is an issue in SNCR. By using SCR better NOx reduction can be achieved but issues with catalyst materials are expected to arise because of the dust and sulphur dioxide which leads to catalyst poison formation in lower flue gas temperatures. NOx scrubbing has potential when simultaneous NOx and SO2 removal is required. The challenge is that NO cannot be scrubbed directly, but once it is oxidized to NO2 or further scrubbing can be performed as the solubility of NO2 is higher. Commercial installations have not been made regarding SNCR, SCR or NOx scrubbing regarding rotary lime kiln. For SNCR and SCR the closest references come from cement industry.

Teollisuuspuhaltimille tarkoitetun suunnittelujärjestelmän kehittäminen

Diplomityön tavoitteena oli kehittää Dust Control Systems Oy:n nykyistä suunnittelujärjestelmää yrityksen toiminnan laadun ja suunnittelun tehokkuuden parantamiseksi. Suunnittelun suurin pullonkaula on valmistusdokumenttien tuottaminen, joten keskeinen tehtävä oli dokumenttien laadun parantaminen ja tuottamisen nopeuttaminen. Lisäksi tärkeää oli selkeyttää nykyistä nimikkeiden hallintaa ja ylläpitoa. Kehitystyö keskittyi suurelta osin suunnittelujärjestelmän ohjelmistoympäristön päivittämiseen ja sen muokkaamiseen. Teoriaosuudessa käsiteltiin nykyaikaista suunnittelua ja sen kehittämismahdollisuuksia. Lisäksi tarkasteltiin suunnittelun automatisoinnin tuomia hyötyjä sekä erilaisia tuotannon tehostamismenetelmiä. Kehitysosiossa tutkittiin yrityksen nykyistä suunnittelujärjestelmää ja ohjelmistoympäristöä, tuotteiden asettamia vaatimuksia sekä järjestelmän puutteita. Näihin liittyi suuresti yhteistyö henkilöstön sekä ohjelmistotoimittajan kanssa. Tutkimuksen perusteella ryhdyttiin kehittämään uutta järjestelmäkokonaisuutta, johon liitettiin tarvittavia ohjelmistoja ja päivityksiä. Käyttöönottoa varten ohjelmistot konfiguroitiin yrityksen tarpeita vastaaviksi. Työn tuloksena saatiin kehittyneempi ja nykyaikaisempi suunnittelujärjestelmä ja ohjelmistoympäristö. Suunnittelijoiden työtaakkaa saadaan kevennettyä toistuvien työvaiheiden pidemmälle viedyllä automatisoinnilla. Uudistettu ohjelmistoympäristö luo osaltaan ehtoja ja sääntöjä, jotta virheitä syntyy yhä vähemmän. Lisäksi suunnittelun läpimenoaikaa saadaan lyhennettyä parannetulla dokumenttien tuottamisella.

Teollisuuspuhaltimien runkorakenteiden ja siipipyörien suunnittelu

Tämä diplomityö tehtiin Voikkaalla Dust Control Systems Oy:lle. Työ on osa teollisuuspuhaltimien tuotekehitystä yrityksen olemassaolevan puhallinratkaisujen, sekä suunnitteluprosessin kautta. Työn tavoitteena oli tutkia puhaltimen toiminnasta aiheutuvan värähtelyn vaikutusta puhaltimen rakenteisiin nykyisillä puhallinmalleilla, sekä tutkia eri rakenneratkaisujen käyttöä yrityksen normaalista tuotelinjasta suuremmilla puhaltimilla. Työ toteutettiin kahden toteutuneen puhallinprojektin yhteydessä, joiden rakenteellisia ominaisuuksia pyrittiin arvioimaan normaalin suunnitteluprosessin ohella puhallinkomponenttien mitoituksen suhteen. Molemmat projektit olivat yrityksen mittakaavassa huomattavan suuria sekä suunnittelultaan haastavia, joten ne sopivat diplomityön toteutukseen hyvin. Suunnittelussa käytettiin FE-mallinnukseen Femap ja COMSOL-ohjelmistoja, sekä värähtelyn simulointiin yliopistolla kehitettyä RoBeDyn – laskentaohjelmaa. Työn aikana todettiin, että tarkempi FE-mallinnus yrityksen valmiista 3D-malleista on varsin hankala toteuttaa ja vaatisi mallien suunnittelun erityisesti lujuuslaskentaa varten. Laskennassa päädyttiin käyttämään yksinkertaistettuja malleja, joiden avulla saatiin johdonmukaisia arvioita puhaltimien toiminnasta eri materiaalivahvuuksilla. Käytännössä tuloksien oikeellisuutta päästään arvioimaan kesällä 2015 puhaltimien valmistuttua.

Immunoglobulin E and systemic lupus erythematosus

Systemic lupus erythematosus (SLE) is an autoimmune disease characterized by intense polyclonal production of autoantibodies and circulating immune complexes. Some reports have associated SLE with a Th2 immune response and allergy. In the present study 21 female patients with SLE were investigated for total IgE and IgE antibodies to dust house aeroallergens by an automated enzyme-linked fluorescent assay, and were also evaluated for antinuclear IgE autoantibodies by a modified indirect immunofluorescence test using HEp-2 cells as antigen substrate. Additionally, immunocapture ELISA was used to investigate serum anti-IgE IgG autoantibodies. Serum IgE above 150 IU/ml, ranging from 152 to 609 IU/ml (median = 394 IU IgE/ml), was observed in 7 of 21 SLE patients (33%), 5 of them presenting proteinuria, urinary cellular casts and augmented production of anti-dsDNA antibodies. While only 2 of 21 SLE patients (9.5%) were positive for IgE antibodies to aeroallergens, all 10 patients with respiratory allergy (100%) from the atopic control group (3 males and 7 females), had these immunoglobulins. SLE patients and healthy controls presented similar anti-IgE IgG autoantibody titers (X = 0.37 ± 0.20 and 0.34 ± 0.18, respectively), differing from atopic controls (0.94 ± 0.26). Antinuclear IgE autoantibodies were detected in 17 of 21 (81%) sera from SLE patients, predominating the fine speckled pattern of fluorescence, that was also observed in IgG-ANA. Concluding, SLE patients can present increased IgE levels and antinuclear IgE autoantibodies without specific clinical signs of allergy or production of antiallergen IgE antibodies, excluding a possible association between SLE and allergy.

Novel Cellular Luminescence Probes for Immunological and Toxicological Assessments

Escherichia coli K-12 (pEGFPluxABCDEAmp) (E. coli-lux), constitutively emitting bioluminescence (BL), was constructed and its BL emitting properties tested in different growth and killing conditions. The BL emission directly correlated with the number of viable E. coli-lux cells, and when subjected to the antimicrobial agent, the diminishment of the BL signal was linked directly to the number of killed bacterial cells. The method provided a very convenient application, especially when compared to conventional plate counting assays. This novel real-time based method was utilized in both immunological and toxicological assessments. The parameters such as the activation phase, the lytic phase and the capacity of the killing of the serum complement system were specified not only in humans but also in other species. E. coli-lux was also successfully used to study the antimicrobial activities of insect haemolymph. The mechanisms of neutrophil activity, like that of a myeloperoxidase (MPO)-H2O2-halide system, were studied using the E. coli-lux approach. The fundamental role of MPO was challenged, since during the actual killing in described circumstances in phagolysosome the MPO system was inactivated and chlorination halted. The toxicological test system, assessing indoor air total toxicity, particularly suitable for suspected mold damages, was designed based on the E. coli-lux method. Susceptibility to the vast number of various toxins, both pure chemicals and dust samples from the buildings and extracts from molds, were investigated. The E. coli-lux application was found to possess high sensitivity and specificity attributes. Alongside the analysis system, the sampling kit for indoor dust was engineered based on the swipe stick and the container. The combination of practical specimen collector and convenient analysis system provided accurate toxic data from the dust sample within hours. Neutrophils are good indicators of the pathophysiological state of the individual, and they can be utilized as a toxicological probe due to their ability to emit chemiluminescence (CL). Neutrophils can either be used as probe cells, directly exposed to the agent studied, or they can act as indicators of the whole biological system exposed to the agent. Human neutrophils were exposed to the same toxins as tested with the E. coli-lux system and measured as luminol amplified CL emission. The influence of the toxins on the individuals was investigated by exposing rats with moniliniformin, the mycotoxin commonly present in Finnish grains. The activity of the rat neutrophils was found to decrease significantly during the 28 days of exposure.

Responses of IgE, IgG1, and IgG4 to concanavalin A-binding Blomia tropicalis antigens in allergic patients

Blomia tropicalis (Bt) and Dermatophagoides pteronyssinus (Dp) are the prevalent house dust mites in tropical countries and are associated with allergic diseases. Glycosylated antigens are highly immunogenic and involved in different pathologies. We evaluated the presence of IgE, IgG1, and IgG4 to concanavalin A-binding antigens (Bt-Con-A) isolated from Bt-total extract in sera of allergic and non-allergic subjects. Bt-total and Bt-Con-A extracts were evaluated by SDS-PAGE and ELISA for reacting with IgE, IgG1, and IgG4 in sera of 121 patients with allergic rhinitis and 36 non-allergic individuals. All subjects were skin prick tested with Bt-total extract and inhibition tests were performed for IgE, IgG1, and IgG4 using both extracts (Bt-total and Bt-Con-A). Skin prick test showed that 58% of the patients were sensitized to Bt (Bt+), with 52% reactive to both mites (Bt and Dp) and 6% to Bt only. A broad spectrum of proteins (14-152 kDa) was visualized in Bt-total and components >27 kDa for the Bt-Con-A extract. ELISA showed a similar profile of IgE, IgG1 and IgG4 levels in response to Bt-total and Bt-Con-A extracts in different groups, although Bt+ patients showed a lower IgG4 reactivity to Bt-Con-A extract. Specific IgG1 levels were higher in Bt+ patients than in control subjects, and IgG4 levels showed no significant difference among groups. ELISA inhibition showed a partial IgE and total IgG1 and IgG4 cross-reactivity with Dp extract for Bt-total and Bt-Con-A extracts. We conclude that Con-A-binding components isolated from Bt constitute major allergens and are involved in both allergen sensitization (IgE response) and homeostasis maintenance (IgG1 and IgG4 responses).

Humoral and cellular immune responses to Blomia tropicalis and concanavalin A-binding fractions in atopic patients

Blomia tropicalis, Dermatophagoides pteronyssinus and D. farinae are prevalent house dust mites. Concanavalin A-binding components derived from B. tropicalis (Bt-ConA extract) are highly immunogenic in allergic diseases. The aim of the present study was to evaluate the humoral and cellular immune responses to B. tropicalis in mite-sensitized patients. A total of 137 patients with allergic rhinitis with/without asthma and 109 non-atopic subjects were selected and analyzed by the skin prick test, and for total serum IgE and specific IgE levels to both Bt-total and Bt-ConA extracts, their proliferative response and cytokine (IFN-γ and IL-5) production by peripheral blood mononuclear cells (PBMC) stimulated with both extracts. Skin prick test showed that 70% of the patients were sensitized to Bt (Bt+) and similar levels of specific IgE to Bt-total and Bt-ConA extracts were demonstrable in Bt+ patients. Significant PBMC proliferation was observed in response to Bt-total extract in Bt+, but not in Bt- patients and non-atopic subjects (P < 0.001). Bt-ConA extract induced increased proliferative responses in all patient groups compared to medium alone (P < 0.05), but these responses were significantly decreased in the presence of the mannopyranoside ConA inhibitor (P < 0.05). Significant IFN-γ production was observed after Bt-ConA stimulation of Bt+ patients (P < 0.05), while Bt-total extract had no effect. IL-5 production was consistently detected in Bt+ patients after allergen-specific stimulation or with no stimulus, indicating that PBMC from allergic patients are prone to produce Th2 profile cytokines, spontaneously or inductively by allergen restimulation. These data showed that ConA-binding components isolated from B. tropicalis may contain relevant antigens that are involved in both humoral and cellular immune responses. However, without an additional purification procedure to eliminate the residual contamination with ConA, its use in immunotherapeutic procedures cannot be recommended.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

The use of film coating on the performance of treated corn seed

The main objective of seed coating technology using polymers is to improve the physical, physiological and sanitary characteristics of seed performance. The objectives of the present study were to determine: the plantability of corn seeds treated with insecticide, fungicide and graphite, covered with a film coating; the dust retention on treated corn seeds; and the leaching of applied products on corn seeds covered by a film coating. Seed plantability was determined by counting the skips and double seeds; dust was determined by using fiberglass paper in mg.100 g-1 of seeds; and the leaching was determined by collecting the material leached in a 10 cm layer of sand after irrigation. The following conclusions were made: seeds covered with film coating effectively reduce skips and double seeds; film coating effectively reduces the formation of dust from the seeds; film coated seeds minimize the leaching of the insecticide applied in seed treatment; and there are differences in effectiveness related to film coating type and dosage.

Kaukolämpöliiketoiminnan kehittäminen Mäntsälän Sähkö osakeyhtiössä

Tämän diplomityön tarkoitus oli selvittää Mäntsälän Sähkö Oy:n kaukolämpöliiketoiminnan nykytila ja kehityskohteet. Tutkimuskysymykset olivat: 1) Millaisilla toimenpiteillä varmistetaan kaukolämpöliiketoiminnan kannattavuus tulevaisuudessa? ja 2) Millaisia mahdollisuuksia älykäs kaukolämpö tuo kaukolämpöliiketoiminnalle? Tutkimus suoritettiin perehtymällä aiheen kirjallisuuteen ja uutisiin. Takaisinmaksuajan menetelmällä arvioitiin maakaasun korvaamisen kannattavuutta. Työn tuloksena voitiin todeta, että kaukolämmön hinnoittelua kannattaa kehittää kustannusvastaavampaan suuntaan. Nykyinen kaukolämmön energiankulutukseen painottuva hinnoittelu ei sovi uusille rakennuksille, jotka kuluttavat vähän energiaa. Yleistyvät hybridilämmitysjärjestelmät on otettava huomioon hinnoittelussa. Kaukolämmön kausihinnoittelu toisi etuja asiakkaalle, kaukolämpöyhtiölle sekä ympäristölle. Kaukolämmön kulutuksen tuntimittaus mahdollistaisi siirtymisen kaukolämpötehoon perustuvaan hinnoitteluun. Kaukolämmön hinta on ollut Mäntsälän Sähkö Oy:llä suhteellisen korkea. Korkea hinta johtuu enimmäkseen maakaasulla tuotetun kaukolämmön korkeista tuotantokustannuksista. Kaukolämmön tuotantoa voidaan kehittää kannattavammaksi, vaikka lämmöntalteenottolaitoksen oletettu lämmöntuotanto kattaa Mäntsälän lämmöntarpeesta noin puolet ja vähentää tuotantokustannuksia. Nykyisten maakaasukattiloiden käyttäminen pelletin pölypolttoon olisi teknisten muutoksien avulla mahdollista. Pölypolton kannattavuus riippuu erityisesti puupelletin ja maakaasun hintaerosta. Älykäs kaukolämpöjärjestelmä voisi automaattisesti tasoittaa kaukolämmön kysyntää yhdessä lämpövaraston kanssa. Tällöin huippulämpölaitosten käyttö vähentyisi ja lämmöntuotannon kustannukset pienentyisivät. Älykäs kaukolämpöjärjestelmä ja kaukolämpötehon tuntimittaus mahdollistaisivat myös kaksisuuntaisen kaukolämpökaupan.

Pollen and grain size records in abyssal sediments of the northwest Pacific Ocean as proxies of Plio-Pleistocene climate change /

A distinctive period of global change occurred during the PUocene between the warm Miocene and subsequent Quaternary cooling. Samples from Ocean Drilling Project Site 11 79 (-5586 mbsl, 41°4'N, 159°57'E), Site 881 (-5765 mbsl, 47°6.133'N, 161°29.490'E) and Site 882 (-3255 mbsl, 50°22'N, 167°36'E) were studied to determine the magnitude and composition ofterrigenous flux to the western mid-latitude North Pacific and its relation to climate change in East Asia since the mid-Pliocene. Dust-sized particles (including pollen), sourced from the arid regions and loess plateaus in East Asia are entrained by prevailing westerly winds and transported to the midlatitude northwest North Pacific Ocean. This is recorded by peaks in the total concentration of pollen and spores, as well as the mean grain size of allochthonous and autochthonous silicate material in abyssal marine sediments. Aridification of the Asian interior due to the phased uplift of the Himalayan-Tibetan Plateau created the modem East Asian Monsoon system dominated by a strengthening of the winter monsoon. The winter monsoon is further enhanced during glacials due to the expansion of desert and steppe environments at the expense ofwoodlands and forests recorded by the composition of palynological assemblages. The late Pliocene-Pleistocene glacials at ODP Sites 1 179, 881, and 882 are characterized by increases in grain size, magnetic susceptibility, pollen and spore concentrations around 3.5-3.3, 2.6-2.4, 1.7-1.6, and 0.9-0.7 Ma (ages based on magnetostratigraphic and biostratigraphic datums). The peaks during these times are relatively rich in pollen taxa derived primarily from steppe and boreal vegetation zones, recording cool, dry climates. The overall size increase of sediment and abundance of terrestrial palynomorphs record enhanced wind strength. The increase in magnitude of pollen and spore concentrations as well as grain size record global cooling and Northern Hemisphere glaciation. The peaks in grain size as well as pollen and spore abundance in marine sediments correlate with the mean grain size of loess in East Asia, consistent with the deflation of unarmoured surfaces during glacials. The transport of limiting nutrients to marine environments enhanced sea surface productivity and increased the rate of sediment accumulation.

Two leaves from a Medieval breviary (prayer-book), c.1350-1400

The actual scripture quotations begin with blue and gold illuminated letters. Towards the end of each passage, there is a small red “R” that marks the “Response”. At the conclusion of the Response, the next lesson is announced. There are three lessons on these leaves. The first leaf begins with the word “Requiem” with the initial letter illuminated. The third lesson begins with the illuminated letter “M” on the word “Manus”. This passage is from the Book of Job, Chapter 10, verses 8-11 which reads: Your hands have formed me and fashioned me; will you then turn and destroy me? Oh, remember that you fashioned me from clay. Will you then bring me down to dust again? Did you not pour me out as milk, and thicken me like cheese? With skin and flesh you clothed me, with bones and sinews knit me together.

Étude polarimétrique d’étoiles jeunes

Afin de mieux comprendre l'évolution des étoiles jeunes, nous avons utilisé un code Monte Carlo simulant leur environnement afin d'étudier une nouvelle distribution chez les étoiles Herbig Ae/Be et pour reproduire des cartes d'intensité et de polarisation linéaire obtenues au télescope Canada-France-Hawaii (TCFH) en novembre 2003. Le code datant de la fin des années 80, nous avons dû non seulement le corriger, mais aussi ajouter quelques éléments afin de tenir compte des dernières avancées dans le domaine de la polarisation provenant du milieu circumstellaire. Les étoiles à l'étude étant jeunes (moins de quelques millions d'années), leur voisinage est toujours constitué de grains de poussière mélangés avec du gaz. Selon leur âge, nous retrouvons cette poussière sous différentes structures soit, par exemple, par un disque entouré d'une enveloppe (objets jeunes de classe I) ou par un simple disque (objets de classe II et III). Selon la structure que prend la poussière, les cartes de polarisation et d'intensité qui en résultent vont changer. Nous allons discuter de cette variation des cartes de polarisation selon la distribution de poussière. Suite aux modifications apportées au code, il a fallu s'assurer que celui-ci fonctionne bien. Pour ce faire, nous avons mis au point quelques critères qui nous assurent, s'ils sont satisfaits, que le code Monte Carlo produit de bons résultats. Après avoir validé le code, il est maintenant possible de l'utiliser aux fins d'avancer le domaine de la polarisation. En effet, Dullemond et al.(2001) proposent une nouvelle distribution de grain autour des étoiles Herbig Ae/Be afin de mieux expliquer leur distribution d'énergie spectrale. Par contre, qu'en est-il des cartes de polarisation résultantes? C'est sur cette question que nous nous sommes arrêtés. Par la suite, nous avons essayé de reproduire du mieux possible, tenant compte des limitations du code, les cartes de polarisation obtenues au TCFH. Nous avons étudié en détail les données de R Mon (résultats qui seront présentés sous forme d'article pour fin de publication) et de V376 Cas. De plus, notre étude de V376 Cas nous a permis d'amener des conclusions sur les processus causant les vecteurs parallèles aux disques des étoiles jeunes.