生态边缘效应与生态平衡变化方向

Human activities produce inany ecosystems which form new edges with original ones.On the other hand, the edge effects also change the quality of ecosystems. The new edge effects will show positive or negative ecological effect on the original ecosystems, which is named as edge effect directivity.Therefoe that human activities can affect the change directions of ecosystem quality with edge effects. It is important to study to the edge effect and the change direction of ecosystem balance,so as to regulate and control the ecosystems wisely.

Enhancements of the simulation method on the edge effect in resin transfer molding processes

In resin transfer molding processes, small clearances exist between the fiber preform and the mold edges, which result in a preferential resin flow in the edge channel and then disrupt the flow patterns during the mold filling stage. A mathematical model including the effect of cavity thickness on resin flow was developed for flow behavior involving the interface between an edge channel and a porous medium. According to the mathematical analysis of momentum equations in a fully developed rectangular duct and formulations of the equivalent edge permeability, comparing with three-dimensional Navier-Stokes equations, the governing equations were modified in the edge channel. The volume of fluid (VOF) method was applied to track the flow front. A simple case is numerically simulated using the modified governing equations. The effects of edge channel width and cavity thickness on flow front and inlet pressure are analyzed, and the evolution characteristics of simulated results are in agreement with the experimental results. (c) 2007 Elsevier B.V. All rights reserved

Simulated morphological landscape of polymer single crystals by phase-field model

The novel phase field model with the "polymer characteristic" was established based on a nonconserved spatiotemporal Ginzburg-Landau equation (TDGL model A). Especially, we relate the diffusion equation with the crystal growth faces of polymer single crystals. Namely, the diffusion equations are discretized according to the diffusion coefficient of every lattice site in various crystal growth faces and the shape of lattice is selected based on the real proportion of the unit cell dimensions.

Effect of shear on the crystallization behavior of glass bead filled polypropylene

Linkam CSS450 optical shearing stage, wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering(SAXS) were used to investigate the effect of shear on crystal structure and crystallization morphology of the glass bead filled polypropylene( PP). The results indicate that the glass bead worked as nucleating agent for the glass bead filled PP, compared with pure PP it restrained the formation of beta-crystal after shear treatment. When the mean size of glass bead is smaller(4 mu m) shear rate had less effect on the formation of beta-crystal of PP obviously.

Nanostructured bulk novel hard material with "rounded" grains obtained by nanocrystalline "rounded" (W0.5Al0.5)C powders

A novel nano-scaled bulk hard material (W0.5Al0.5)C-Co with "rounded" grains was prepared by nanocrystalline "rounded" (W0.5Al0.5)C powders with "rounded" particle shape in this study. The nano-scaled "rounded" particles do not contain sharp edges, which form local tensile stress concentrations on loading of the composite, thus leading to improved toughness and reduced sensitivity to crack. Nanocrystalline (W0.5Al0.5)C powders with "rounded" particle shape were used as starting materials. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used to characterize the samples.

Hot-corrosion behaviors of overlay-clad yttria-stabilized zirconia coatings in contact with vanadate-sulfate salts

A dense clad overlay with chemical inertness was achieved on top of the plasma-sprayed YSZ thermal barrier coatings by laser in order to protect them from hot-corrosion attack. The Al2O3-clad YSZ coating exhibited good hot-corrosion behavior in contact with salt mixture of vanadium pentoxide (V2O5) and sodium sulfate (Na2SO4) for a longtime of 100 h at 1173 K. The LaPO4-clad YSZ coating showed corrosion resistance inferior to the Al2O3-clad one. Yttria was leached from YSZ by reaction between Y2O3 and V2O5, which caused progressive destabilization transformation of YSZ from tetragonal (t) to monoclinic (m) phase. The chemical inertness of the clad layers and the restrained infiltration of the molten corrosive salts by the dense clad layers were primary contributions to improvement of the hot-corrosion resistances.

Insight into growth details and characteristics of windmill-like polyethylene crystals

The crystallization detail of polyethylene (PE) has been scarcely studied via in-situ approach since it is an extremely fast process. In this work, optical microscopy is used to investigate crystallization details and characteristics of windmill-like polyethylene crystals. It has been shown that the straight edges of the petals appear firstly and grow in pairs from their central junctions, which subsequently induce the surrounding domains in between each pairs of petals to nucleate and crystallize into twisted lamellar overgrowths. The remaining terrace-stacked lamellae which form curved edges of the petals start to develop only after the straight edges of the petals together with the twisted lamellar overgrowths have completed their growth. It is confirmed that the preferential growth direction of these petals are along crystallographic [113] axis, which has an angle of 65, with the typical direction along b-axis adopted also by the twisted lamellar overgrowths.

Micropatterning of polymeric semiconductor by selective lift-off method using epoxy mold

A simple and efficient method for patterning polymeric semiconductors for applications in the field of organic electronics is proposed. The entire polymer layer, except for the desired pattern, is selectively lifted off from a flat poly(dimethylsiloxane) (PDMS) stamp surface by an epoxy mold with a relief pattern. This is advantageous because the elastic deformation of the PDMS stamp around protrusions of a patterned stamp under pressure can assist the plastic deformation of a polymer film along the pattern edges, yielding large area and high quality patterns, and the PDMS surface has low surface energy, which allows the easy removal of the polymer film.

Crystallization Behavior and Mechanical Properties of Crosslinked Plasticized Poly(L-lactic acid)

Enhancing the stability of plasticized poly(L-lactic acid) (PLLA) with poly (ethylene glycol) (PEG) is necessary for its practical application. In this study, plasticized PLLA (PLLA/PEG 80/20 wt/wt) was crosslinked under I-ray (Co-60) in the presence of triallyl isocyanurate (TALC) as crosslinking agent. FTIR analysis revealed that PLLA, PEG, and TALC formed a cocrosslinking structure. Crystallization behavior and mechanical properties of the crosslinked plasticized PLLA were investigated by differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), scanning electron microscopy (SEM), and tensile tests. Experimental results indicated that the crystallization behaviors of both PEG and PLLA in the blends were restrained after irradiation. The melting peak of PEG in the crystallized samples disappeared at a low irradiation doses about 10 kGy. Although PLLA still owned the behavior of crystallize, its cold crystallization temperature and glass transition temperature shifted to higher temperature. Mechanical properties of the plasticized PLLA were strengthened through crosslinking. Both yield strength and elastic modulus of the samples increased after crosslinking.

Study on the variation of chemical constituents during combination of ginseng with trogopteroum feces and semen raphani by high performance liquid chromatography-mass spectrometry

A high performance liquid chroatography-electrospray ionization-mass spectrometric method was developed for analysis and identification of ginsenosides from the decoction of ginseng, ginseng with trogopteroum feces and ginseng with semen raphani. Ten ginsenosides were separated and detected. The content variation of these ginsenosides was researched. The experimental results showed, that ginsenosides were less in compatible decoction than in separate one expect Ro. the stripping of ginsenosides were restrained by semen raphani and during combination of ginseng with trogopteroum feces, the precipitates were produced by ginsenosides.

Synthesis, structure and photochromic properties of a novel 1,6-hexanediamine trimolybdate supramolecular compound

A novel supramolecular compound 1,6-hexanediamine trimolybdate ((C6H18N2[Mo3O10], denoted as HDAMo) has been synthesized by a hydrothermal method and its structure has been characterized by elemental analyses, Fourier transform infrared (FT-IR) spectra, single-crystal X-ray diffraction (XRD) technique. This single crystal compound consists of protonated 1,6-hexanediamine (HDA) cations and polyoxometalate [Mo3O10](2-) anions. Its crystal structure belongs to monoclinic system (space group P2(1)/n) with a = 7.7508(14), b = 11.467(2), c = 16.167(3) angstrom, beta = 92.689(3)degrees, V = 143 5.3(5) angstrom(3), Z = 4 and D-ealc = 2.619 g cm(-3). The final statistics based on F-2 are GOF = 0.980, R-1 = 0.0261 and wR(2) = 0.0506 for I > 2 sigma(I). XRD analysis revealed that in the crystal structure of HDAMo, novel infinite [Mo3O10](2-) chains parallel to a axis are made up of distorted MoO6 octahedra connected by corners and edges. The protonated HDA cations occupy channels formed by [Mo(3)O3(10)](2-) Chains and exhibit strong hydrogen bond interactions to terminal and bridging oxo groups of the chains. The [Mo3O10](2-) chains linked through protonated HAD cations formed a one-dimensional network. The HDAMo compound shows novel photochromic properties, i.e., its color changes from white to reddish brown gradually under UV irradiation. XRD, FT-IR, ESR spectra and XPS are used to investigate the photochromic behavior of the compound.

Effect of cerium on microstructure and electrochemical performance of Ti-V-Cr-Ni electrode alloy

Effect of cerium on the microstructure and electrochemical performance of the Ti0.25V0.35-xCexCr0.1Ni0.3 (x = 0, 0.005) electrode alloy was investigated by X-ray diffraction (XRD), field emission scanning electron microscopy/energy dispersive X-ray spectrometry (FESEM-EDS), and electrochemical impedance spectroscopy (EIS) measurements. On the basis of XRD and FESEM-EDS analysis, the alloy was mainly composed of V-based solid solution with body-centered-cubic structure and TiNi-based secondary phase. Ce did not exist in two phases, instead, it existed as Ce-rich small white particles, with irregular edges, distributed near the grain boundaries of the V-based solid solution phase. Discharge capacity, cycle stability, and high-rate discharge ability of the alloy electrode were effectively improved with the addition of Ce at 293 K. It was very surprising that the charge retention was abnormal with larger discharge capacity after standing at the open circuit for 24 h. EIS indicated that addition of Ce improved the dynamic performance, which caused the charge transfer resistance (R-T) to decrease and exchange current density (I-0) to increase markedly. The exchange current density of the electrochemical reaction on the alloy surface with Ce addition was about 2.07 and 3.10 times larger than that of the alloy without Ce at 303 and 343 K, respectively.

In situ synthesis of silica gel nanowire/Na+-montmorillonite nanocomposites by the sol-gel route

Silica-gel nanowire/Na+-montmorillonite (Na+-MMT) nanocomposites were prepared by the in situ sol-gel process of tetraethyl orthosilicate (TEOS) in the presence of Na+-MMT and ammonia as catalyst. Microstructure characterization of the nanocomposites was done by SEM, , EDX, XRD and FTIR. It was found that a lot of silica-gel nanowires grew along the edges of Na+-MMT. The combination between the nanowires and Na+-MMT was accomplished via polycondensation of the hydrolyzed TEOS and the edge-OH groups of Na+-MMT.

Micropatterning of metal films coated on polymer surfaces with epoxy mold and its application to organic field effect transistor fabrication

In this letter, a simple and versatile approach to micropatterning a metal film, which is evaporated on a Si substrate coated with polymer, is demonstrated by the use of a prepatterned epoxy mold. The polymer interlayer between the metal and the Si substrate is found important for the high quality pattern. When the metal-polymer-Si sandwich structure is heated with the temperature below T-m but above T-g of the polymer, the plastic deformation of the polymer film occurs under sufficiently high pressure applied. It causes the metal to crack locally or weaken along the pattern edges. Further heating while applying a lower pressure results in the formation of an intimate junction between the epoxy stamp and the metal film. Under these conditions the epoxy cures further, ensuring adhesion between the stamp and the film. The lift-off process works because the adhesion between the epoxy and the metal film is stronger than that between the metal film and the polymer. A polymer field effect transistor is fabricated in order to demonstrate potential applications of this micropatterning approach.

Hydrothermal synthesis, structure, and characterization of two one-dimensional chainlike hybrid complexes [(CuX)(2)(o-phen)](infinity) (X = Br, Cl; o-phen = o-phenanthroline)

Two novel organic-inorganic hybrid complexes [(CuX)(2)(o-phen)](infinity) (X = Br (1), Cl (2); o-phen = o-phenanthroline) have been synthesized hydrothermally and characterized structurally by elemental analyses, IR, ESR, XPS spectrum, TG analyses and single-crystal X-ray diffraction. Both title compounds exhibit novel one-dimensional chainlike copper halide scaffolding constructed by the unusual [Cu3X3] hexagon motifs by sharing opposite edges, where a single Cu site of each [Cu3X3] hexagon is chelated with N donors of o-phen group. To our knowledge, such basic o-phen-copper halide skeleton has not been reported hitherto. Moreover, TG analyses indicate that both title compounds possess high thermal stability.