Effect of abscisic acid on the mobilisation of galactomannan and embryo development of Sesbania virgata (Cav.) Pers. (Leguminosae - Faboideae)

Galactomannans (GM) are storage cell wall polysaccharides present in endospermic seeds of legumes. They are thought to be storage polymers, since it has been observed for a few species (among them Sesbania virgata) that they are completely broken down after germination and their products are transferred to the growing embryo. We examined the effect of 10-4 M abscisic acid (ABA) on the degradation of galactomannan in isolated endosperms and intact seeds of S. virgata. We found that after seed germination the initial embryo growth was retarded. Ultrastructural analysis showed that the embryo is completely surrounded by an endosperm which displays very thick galactomannan-containing cell walls. Although an inhibitory effect has been observed on the increase of fresh mass of the embryo, the effect of ABA on the dry mass was weaker and transitory (from 48 to 96 h). Endosperm dry mass and galactomannan degradation were significantly inhibited and the activity of alpha-galactosidase was strongly affected. The addition of ABA before and/or after the start of mobilisation in intact seeds or isolated endosperms, showed that whereas addition before mobilisation did not affect dry mass decrease in intact seeds, it was strongly affected in isolated endosperms. On the other hand, whereas it affected embryo fresh mass increase in intact seeds, but not in isolated embryos, no significant effect was observed on dry mass. These results suggest that ABA affects galactomannan degradation and by doing so, prevents water absorption by the embryo, rather than affect its dry mass. As ABA has been detected in the endosperm of seeds of S. virgata, it is proposed that it probably acts as a modulator of galactomannan mobilisation and consequently synchronises it with early growth of the embryo.

Quantitative variables applied to phenological studies of Sargassum vulgare C. Agardh (Phaeophyceae - Fucales) from Ilha Grande Bay, State of Rio de Janeiro

The suitability of quantitative variables for phenological studies was evaluated in a population of the brown seaweed Sargassum vulgare from "Praia das Gordas", Angra dos Reis, Ilha Grande Bay, state of Rio de Janeiro. From June 1998 to May 1999, twenty adult individuals were randomly sampled at bimonthly intervals. Fifteen variables related to the vegetative and reproductive development of perennial and non-perennial parts of the individuals were quantified. Variables related to the non-perennial parts were more useful than those related to the perennial parts, because they showed a clear variation over the year. Vegetative development declined from June to October, and increased from October to February, when maximum median values of thallus height, total dry mass, non-perennial parts dry mass, and degree of branching were reached. This pattern coincided with those described for other species of the genus from warm temperate regions. Thallus height, a usually employed character in other phenological studies of Sargassum, showed lower coefficient of variation (53.2%) than those related to dry mass (72.0% to 182.3%). Peak of reproduction occurred from June to August, according to the following variables: fertile primary lateral branches number and dry mass and receptacles dry mass. Non-perennial parts dry mass and receptacles dry mass are recommended for phenological studies of S. vulgare. This methodological procedure avoids the sampling of the whole individual and warrants its regeneration from the perennial parts.

Viability and vigor of jamun (Syzygium cumini) seeds

Jamun (Syzygium cumini L. Skeels) (Black plum, Damson plum) fruits weigh between 2-5 g at maturity. Fresh seeds represented 20-80% of the total fruit weight; the seed coat and cotyledons contributed 6% and 94% to the total seed weight respectively, while the weight of the embryonic axis was insignificant. Only the embryonic axis stained with Tetrazolium, not the cotyledons. The seeds are polyembryonic with up to four embryos, of which at most three germinate. Decoated seeds germinated faster than coated seeds under nursery conditions, with high significant germination percentages, dry matter production rates and vigor indices. The lack of staining of the cotyledon by tetrazolium was probably due to the presence of an impermeable layer. Decoating seeds for faster germination is recommended.

Concanavalin A-reactive nuclear matrix glycoprotein

The binding capacity of concanavalin A (Con A) to condensed euchromatin and heterochromatin was investigated in chicken erythrocyte nuclei (CEN), mouse liver cells, Zea mays mays meristematic cells and Drosophila melanogaster polytene chromosomes after 4 N HCl hydrolysis to determine whether binding was preferentially occurring in bands and heterochromatin. Dry mass (DM) variation was investigated in CEN by interference microscopy. Feulgen and Con A reactions were employed for all materials to correlate the loci of the two reactions. Quantifications and topological verifications were carried out by video image analysis (high performance cytometry). It was observed that 4 N HCl hydrolysis caused an important DM loss in CEN leaving a level corresponding to the average DNA DM content. In this material, Con A binding was restricted to the nuclear envelope, which reinforces the idea of the absence of a nuclear matrix in these cells. The other cell types exhibited a correspondence of Feulgen-positive and Con A-reactive areas. The Con A reaction was highly positive in the condensed chromatin areas and heterochromatin. This fact led us to speculate that Con A-positive proteins may play a role in the chromatin condensation mechanism, endowing this structure with physico-chemical stability towards acid hydrolysis and contributing to its rheological properties.

Physiological maturity of seeds and colorimetry of fruits of Jatropha curcas L.

The objective was to relate the coloration of fruits of Jatropha curcas L during the maturation process with morphometric (fruits and seeds) and germinative characteristics (seeds). Fruits were collected at various maturation stages from mast trees located in Eldorado/MS, and six maturation stages were visually classified based on fruit's epicarp color. Epicarp digital colorimetry was used to characterize maturation stages in addition to morphometric variables of length and width of fruits and seeds, as well their water content. For determining the physiological potential it was used germination test, emergence velocity index and first count of germination. Results indicated that seeds of J. curcas should be harvested when fruit epicarp shows a reading equal or smaller than 82, 70 or 65 nm of red, green or blue scales from a digital color analyzer. Seeds of fruits with that colorimetry can be harvested in virtue of the maxim acumululation of dry mass, water content below 38,5% and higher physiological potential.

Direct effects of soybean seed vigor on weed competition

Seed vigor is one of the factors that determines the speed and uniformity of seedling emergence and initial plant growth, which are crucial aspects in the competition against weeds. The objective of this study was to verify the direct effects of soybean seed vigor on weed competition and grain yield. A field experiment was conducted with three seed lots of the "Conquista" cultivar, previously characterized by physiological tests as having high, intermediate and low vigor. The experiment was divided into weeded and unweeded plots with six treatments. Crop plant height, weed dry mass accumulation and crop grain yield data were recorded. Seed vigor did not affect plant height and grain yield. Plants which developed from seeds with high and intermediate vigor showed the best results for competition against weeds, reducing weed dry mass accumulation. Plants which developed from high vigor seeds give the best results for grain yield for both weeded and unweeded treatments.

Chemical and biological treatments of castor bean seeds: effects on germination, emergence and associated microorganisms

The effect of chemical and biological treatments on castor bean emergence, seedling vigor, dry matter production, and also the control of microorganisms associated with seeds of the AL Guarany 2002 and Lyra cultivars, was evaluated. The products tested were carbendazim + thiram, carboxin + thiram and a product based on Trichoderma. Total seed and seedling emergence were evaluated at 27 days after sowing whereas dry matter production was verified for plants removed 45 days after sowing. The Guarany 2002 AL cultivar had a higher incidence of microorganisms than the Lyra cultivar. The chemical treatment was 100% effective in controlling fungi but the biological treatment did not reduce microorganism incidence on the seeds. Chemical treatment resulted in plants with more dry matter and the best results were for carbendazim + thiram and carboxin + thiram at doses of 60 g + 140 g and 50 g + 50 g/100 kg of seeds, respectively. The carbendazim + thiram mixture was the only treatment which was statistically higher for total emergence whereas the biological treatment increased emergence only for the Lyra cultivar, thus demonstrating its lower efficiency. The importance of fungicides to control pathogens associated with seeds was discussed.

Physiological maturity of fruits and seeds of Poincianella pyramidalis (Tul.) L.P. Queiroz

The Leguminosae family is one of the most representative botanical families of the Caatinga, with 80 endemic species, highlighting the catingueira (Poincianella pyramidalis). The objective of this research work was to study the maturation process of P. pyramidalis seeds based on the physiological maturity. Five harvest of fruits and seeds were carried out, with 15 days interval each, in a period from July to September 2010. The harvests began 75 days after anthesis (d.a.a.) and lasted until 135 d.a.a. Fruits and seeds were subjected to the following assessments: size, moisture content, and dry mass of fruits and seeds; and germination and vigor of seeds (first count of germination, germination speed index, length and dry mass of seedling). Under the environmental conditions of municipality of Soledade, State of Paraiba, Northeast Brazil, the point of physiological maturity of P. pyramidalis seeds occurs at 125 d.a.a., when the maximum accumulation of dry mass is 1.993 g and moisture content is 21%. The ideal point of harvest is between 130 d.a.a and 135 d.a.a., before natural dehiscence, when the moisture content of seeds is between 13.0% and 5.0%.

RR soybean seed quality after application of glyphosate in different stages of crop development

In consequence of several studies and speculations concerning the issue of RR transgenic soybean after the application of glyphosate, additional scientific investigations became necessary to clarify the actual viability of the product use when applied in different developmental stages of the soybean crop. Therefore, this study was aimed to evaluate the physiological quality as well as seed health quality of RR soybean subjected to application of the herbicide glyphosate in different phonological stages of the transgenic soybean, cultivar CD 219RR. For this, an experiment with a complete block experimental design with treatments randomly distributed within the block, with four replications, was carried out. The assessed treatments were foliar sprayings of glyphosate in three increasing dosages [0 (control); 1,440 g ha-1; and 2,880 g ha-1] of acid equivalent, applied in two crop developmental stages: vegetative (V6) and reproductive (R2). The variables assessed were: germination; first count of germination; fresh and dry mass of seedlings, lengths of seedling and root; vigor and viability by the tetrazolium test; and seed health quality. Glyphosate application may adversely affect physiological quality of RR soybean seeds, when applied in dosages varying from 1,440 to 2,880 g acid equivalent per hectare at the stages V6 and R2.

Modulaarinen arkkitehtuuri tuoteperheen kehittämisessä

Modulaarisen tuotteen kehittäminen tehostaa yrityksen kilpailukykyä ja helpottaa asiakkaiden tarpeiden tyydyttämistä. Tuoteperheen edut verrattaessa massatuotantoon ovat laajempi tuotevalikoima sekä parempi tuotettavuus massaräätälöintiin verrattuna. Eri tuotevaihtoehtoja ja moduuleja on mahdollista kehittää rinnakkain. Moduloitava tuoteperhe helpottaa yrityksen eri vaiheita aina tuotteen suunnittelusta huoltotoimenpiteisiin ja lopulta tuotteen purkamiseen. Asiakkaille tärkeitä hyötyjä moduloinnin osalta ovat tuotteiden parempi laatu ja huollettavuus. Täysin uuden modulaarisen tuoteperheen kehittäminen vaatii runsaasti resursseja suunnitteluosastolla. Modulaarisessa tuotteessa suunnittelutyö voidaan kohdistaa vain tietyn moduulin kohdalle ja suunnitteluaikoja saadaan täten lyhennettyä. Tässä kandidaatintyössä tutkittiin, miten hitsausautomaatiosovelluksissa modulaarisuus on toteutettu sekä pohditaan kehityskohteita, koska hitsausautomaatiosovelluksia tuotetaan runsaasti asiakasräätälöintinä. Tarkasteltavana tuoteperheenä oli robottihitsausportaalit ja hitsaustornit.

Hydrogen Sensor Application of Anodic Titanium Oxide Nanostructures

Hydrogen (H2) fuel cells have been considered a promising renewable energy source. The recent growth of H2 economy has required highly sensitive, micro-sized and cost-effective H2 sensor for monitoring concentrations and alerting to leakages due to the flammability and explosiveness of H2 Titanium dioxide (TiO2) made by electrochemical anodic oxidation has shown great potential as a H2 sensing material. The aim of this thesis is to develop highly sensitive H2 sensor using anodized TiO2. The sensor enables mass production and integration with microelectronics by preparing the oxide layer on suitable substrate. Morphology, elemental composition, crystal phase, electrical properties and H2 sensing properties of TiO2 nanostructures prepared on Ti foil, Si and SiO2/Si substrates were characterized. Initially, vertically oriented TiO2 nanotubes as the sensing material were obtained by anodizing Ti foil. The morphological properties of tubes could be tailored by varying the applied voltages of the anodization. The transparent oxide layer creates an interference color phenomena with white light illumination on the oxide surface. This coloration effect can be used to predict the morphological properties of the TiO2 nanostructures. The crystal phase transition from amorphous to anatase or rutile, or the mixture of anatase and rutile was observed with varying heat treatment temperatures. However, the H2 sensing properties of TiO2 nanotubes at room temperature were insufficient. H2 sensors using TiO2 nanostructures formed on Si and SiO2/Si substrates were demonstrated. In both cases, a Ti layer deposited on the substrates by a DC magnetron sputtering method was successfully anodized. A mesoporous TiO2 layer obtained on Si by anodization in an aqueous electrolyte at 5°C showed diode behavior, which was influenced by the work function difference of Pt metal electrodes and the oxide layer. The sensor enabled the detection of H2 (20-1000 ppm) at low operating temperatures (50–140°C) in ambient air. A Pd decorated tubular TiO2 layer was prepared on metal electrodes patterned SiO2/Si wafer by anodization in an organic electrolyte at 5°C. The sensor showed significantly enhanced H2 sensing properties, and detected hydrogen in the range of a few ppm with fast response/recovery time. The metal electrodes placed under the oxide layer also enhanced the mechanical tolerance of the sensor. The concept of TiO2 nanostructures on alternative substrates could be a prospect for microelectronic applications and mass production of gas sensors. The gas sensor properties can be further improved by modifying material morphologies and decorating it with catalytic materials.

Asuntorakentamisen vakioidut tekniset ratkaisut rakennettavuuden ja kustannustehokkuuden varmistamiseksi suunnittelunohjauksessa

Rakennushankkeen suunnitteluvaiheen ratkaisut määrittävät merkittävästi hankkeen laatua, aikataulutusta ja kustannustasoa. Tutkimuksen tavoitteena oli selvittää teknisten suunnittelualustojen ja vakioinnin käytön nykytilaa sekä kustannusvaikutuksia kohdeyrityksessä. Kirjallisuustutkimuksessa suunnittelualustat nähtiin työkaluna vakioinnin lisäämiseen suunnitteluprosessissa ja hyvänä keinona suunnittelijoiden ohjaamiseksi. Työ on tutkimusmenetelmiltään laadullinen tapaustutkimus, jossa teknisten ratkaisuiden vakiointipotentiaalia ja kustannustehokkuutta tutkittiin kolmessa erityyppisessä rakenneratkaisussa. Kohdeyrityksen kustannustiedon ja asiantuntijahaastattelujen avulla vertaillut rakenteet oli ilmastointikonehuone, kylpyhuone ja parveke-elementti. Tutkimuksen keskeisissä tuloksissa suunnittelualustan ratkaisuiden käyttö kohdeyrityksessä on varsin säännönmukaista ja valvottua alustan käytön integroituessa osaksi suunnitteluprosessia. Vakioinnin ja esivalmistusasteen lisääminen tarjoaa potentiaalia parantaa rakennettavuutta ja laatua. Vakioinnin mahdollistama sarjavalmistuksen tehokkaampi hyödyntäminen ja vakioinnin volyymiedut ovat potentiaalinen keino alentaa yksikkökustannuksia. Vakioinnin ja esivalmistuksen aikatauluetujen kustannusvaikutus on merkittävä tuotannon aikasidonnaisten kustannusten pienentyessä ja pääoman käytön tehostuessa.

Pulssitettu laserablaatio mikrofluidisten kanavistojen sarjatuotantomenetelmänä

Puolijohteiden yleistyttyä vuodesta 1948 alkaen, ovat elektroniset laitteet pienentyneet jatkuvasti tehojen kuitenkin kasvaessa. Kasvaneet tehotiheydet kuitenkin vaikeuttavat laitesuunnittelua, sillä puoljohdekomponenttien suorituskyvylle ja eliniälle on oleellista lämpötilojen ja lämpötilavaihteluiden minimointi. Perinteisen ilmajäähdytyksen lähestyessä rajojaan niin kokonaistehon kuin järkevän energiatehokkuudenkin suhteen, on parhaaksi seuraavaksi teknologiaksi ennustettu kaksifaasijäähdytystä, jonka suorituskyky ja energiatehokkuus ovat vaaditulla tasolla. Kaksifaasijäähdytyksen optimaaliselle toiminnalle tärkeää on hyvin suunniteltu ja tarkasti valmistettu lämmönsiirtopinta, jota kutsutaan mikrokanavistoksi. Pulssitettu laserkaiverrus on edistynyt valmistustekniikka, jonka tarkkuus ja luotettavuus sopisivat mikrokanavistojen valmistamiseen. Laserkaiverruksella saavutettavat lopputulokset vaihtelevat kuitenkin materiaalista riippuen ja kupari – jota käytetään yleisesti lämmönjohteena – on eräs huonoimmin lasertyöstöön reagoivista materiaaleista ja siksi on oleellista selvittää laser-kaiverruksen toimivuutta kuparisten mikrokanavistojen valmistuksessa. Pulssitetun laser-kaiverruksen eri variaatioista nanosekunti-luokan pulssinpituuksilla toimivat laitteet ovat jatkuvan tuotannon kannalta paras vaihtoehto niiden hyvän tuottavuuden, saatavuuden sekä kohtuullisen alkuinvestoinnin vuoksi. Käytännön kaiverruskokeiden perusteella selvisi, että menetelmä on laatunsa ja tarkkuutensa puolesta sopiva varsinaiseen tuotantoon. Kaiverruksen tehokkuus kuparia työstettäessä on kuitenkin ennakoituakin heikompi ja niin valmistus- kuin suunnitelu-prosessikin vaativat vielä jatkotutkimusta ja -kehitystä.

Impact of different irrigation strategies on grapes and wine quality of four grapevine cultivars (Vitis sp.) in cool climate conditions. An investigation into the relationships among ABA, water status, grape cultivar and wine quality

Niagara Peninsula of Ontario is the largest viticultural area in Canada. Although it is considered to be a cool and wet region, in the last decade many water stress events occurred during the growing seasons with negative effects on grape and wine quality. This study was initiated to understand and develop the best strategies for water management in vineyards and those that might contribute to grape maturity advancement. The irrigation trials investigated the impact of time of initiation (fruit set, lag phase and veraison), water replacement level based on theoretical loss through crop evapotranspiration (ETc; 100,50 and 25%) and different irrigation strategies [partial root zone drying (PRD) versus regulated deficit irrigation (RD!)] on grape composition and wine sensory profiles. The irrigation experiments were conducted in a commercial vineyard (Lambert Vineyards Inc.) located in Niagara-on-the-Lake, Ontario, from 2005 through 2009. The two experiments that tested the combination of different water regimes and irrigation time initiation were set up in a randomized block design as follows: Baco noir - three replicates x 10 treatments [(25%, 50% and 100% of ETc) x (initiation at fruit set, lag phase and veraison) + control]; Chardonnay - three replicates x seven treatments [(25%, 50% and 100% of ETc) x (initiation at fruit set and veraison) + control]. The experiments that tested different irrigation strategies were set up on two cultivars as follows: Sauvignon blanc - four replicates x four treatments [control, fully irrigated (100% ETc), PRD (100% ETc) and RDI (25% ETc)]; Cabemet Sauvignon - four replicates x five treatments [control, fully irrigated (100% ETc), PRD (100% ETc), RDI (50% ETc) and RDI (25% ETc)]. The controls in each experiment were nonirrigated. The irrigation treatments were compared for many variables related to soil water status, vine physiology, berry composition, wine sensory profile, and hormone composition [(abscisic acid (ABA) and its catabolites]. Soil moisture profile was mostly affected by irrigation treatments between 20 and 60 em depth depending on the grapevine cultivar and the regime of water applied. Overall soil moisture was consistently higher throughout the season in 100 and 50% ETc compare to the control. Transpiration rates and leaf temperature as well as shoot growth rate were the most sensitive variables to soil water status. Drip irrigation associated with RDI treatments (50% ETc and 25% ETc) had the most beneficial effects on vine physiology, fruit composition and wine varietal typicity, mainly by maintaining a balance between vegetative and reproductive parts of the vine. Neither the control nor the 100 ETc had overall a positive effect on grape composition and wine sensory typicity. The time of irrigation initiation affected the vine physiology and grape quality, the most positive effect was found in treatments initiated at lag phase and veraison. RDI treatments were overall more consistent in their positive effect on grape composition and wine varietal typicity comparing to PRD treatment. The greatest difference between non-irrigated and irrigated vines in most of the variables studied was found in 2007, the driest and hottest season of the experimental period. Soil water status had a greater and more consistent effect on red grapevine cultivars rather than on white winegrape cultivars. To understand the relationships among soil and plant water status, plant physiology and the hormonal profiles associated with it, abscisic acid (ABA) and its catabolites [phaseic acid (PA), dihydrophaseic acid (DPA), 7-hydroxy-ABA (TOH-ABA), 8' -hydroxy-ABA, neophaseic acid and abscisic acid glucose ester (ABA-GE)] were analyzed in leaves and berries from the Baco noir and Chardonnay irrigation trials over two growing seasons. ABA and some of its catabolites accurately described the water status in the vines. Endogenous ABA and some of its catabolites were strongly affected in Baco noir and Chardonnay by both the water regime (i.e. ET level) and timing of irrigation initiation. Chardonnay grapevines produced less ABA in both leaves and berries compared to Baco noir, which indicated that ABA synthesis is also cultivar dependant. ABA-GE was the main catabolite in treatments with high water deficits, while PA and DPA were higher in treatments with high water status, suggesting that the vine produced more ABA-GE under water deficits to maintain rapid control of the stomata. These differences between irrigation treatments with respect to ABA and catabolites were particularly noticeable in the dry 2007 season. Two trials using exogenous ABA investigated the effect of different concentrations of ABA and organs targeted for spraying, on grape maturation and berry composition of Cabemet Sauvignon grapevines, in two cool and wet seasons (2008-2009). The fIrst experiment consisted of three replicates x three treatments [(150 and 300 mg/L, both applications only on clusters) + untreated control] while the second experiment consisted in three replicates x four treatments [(full canopy, only clusters, and only leaves sprayed with 300 ppm ABA) + untreated control]. Exogenous ABA was effective in hastening veraison, and improving the composition of Cabemet Sauvignon. Ability of ABA to control the timing of grape berry maturation was dependant on both solution concentration and the target organ. ABA affected not only fruit composition but also yield components. Berries treated with ABA had lower weight and higher skin dry mass, which constitutes qualitative aspects desired in the wine grapes. Temporal advancement of ripening through hormonal control can lead to earlier fruit maturation, which is a distinct advantage in cooler areas or areas with a high risk of early frost occurrence. Exogenous ABA could provide considerable benefits to wine industry in terms of grape composition, wine style and schedule activities in the winery, particularly in wet and cool years. These trials provide the ftrst comprehensive data in eastern North America on the response of important hybrid and Vitis vinifera winegrape cultivars to irrigation management. Results from this study additionally might be a forward step in understanding the ABA metabolism, and its relationship with water status. Future research should be focused on ftnding the ABA threshold required to trigger the ripening process, and how this process could be controlled in cool climates.

Applying 3D modelling technology to traditional craftwork : rapid prototyping in artisanal jewellery making and its impact on the perceived value of jewellery

Depuis la révolution industrielle, l’évolution de la technologie bouleverse le monde de la fabrication. Aujourd'hui, de nouvelles technologies telles que le prototypage rapide font une percée dans des domaines comme celui de la fabrication de bijoux, appartenant jadis à l'artisanat et en bouscule les traditions par l'introduction de méthodes plus rapides et plus faciles. Cette recherche vise à répondre aux deux questions suivantes : - ‘En quoi le prototypage rapide influence-t-il la pratique de fabrication de bijoux?’ - ‘En quoi influence-t-il de potentiels acheteurs dans leur appréciation du bijou?’ L' approche consiste en une collecte de données faite au cours de trois entretiens avec différents bijoutiers et une rencontre de deux groupes de discussion composés de consommateurs potentiels. Les résultats ont révélé l’utilité du prototypage rapide pour surmonter un certain nombre d'obstacles inhérents au fait-main, tel que dans sa géométrie, sa commercialisation, et sa finesse de détails. Cependant, il se crée une distance entre la main du bijoutier et l'objet, changeant ainsi la nature de la pratique. Cette technologie est perçue comme un moyen moins authentique car la machine rappelle la production de masse et la possibilité de reproduction en série détruit la notion d’unicité du bijou, en réduisant ainsi sa charge émotionnelle. Cette recherche propose une meilleure compréhension de l'utilisation du prototypage rapide et de ses conséquences dans la fabrication de bijoux. Peut-être ouvrira-t-elle la voie à une recherche visant un meilleur mariage entre cette technique et les méthodes traditionnelles.