966 resultados para 53-418_Site
Resumo:
Zeolite N, a zeolite referred to in earlier publications as MesoLite, is made by caustic reaction of kaolin at temperatures between 80 °C and 95 °C. This material has a very high cation exchange capacity (CEC ≈ 500 meq/100 g). Soil column leaching experiments have shown that K-zeolite N additions greatly reduce leaching of NH4+ fertilisers but the agronomic effectiveness of the retained K+ and NH4+ is unknown. To measure the bioavailability of K in this zeolite, wheat was grown in a glasshouse with K-zeolite N as the K fertiliser in highly-leached and non-leached pots for four weeks and compared with a soluble K fertiliser (KCl). The plants grown in non-leached pots and fertilised with K-zeolite N were slightly larger than those grown with KCl. The elemental compositions in the plants were similar except for Si being significantly more concentrated in the plants supplied with K-zeolite N. Thus K-zeolite N may be an effective K-fertiliser. Plants grown in highly-leached pots were significantly smaller than those grown in non-leached pots. Plants grown in highly-leached pots were severely K deficient as half of the K from both KCl and K-zeolite N was leached from the pots within three days.
Resumo:
The surface amorphous layer of articular cartilage is of primary importance to its load-bearing and lubrication function. This lipid-filled layer is degraded/disrupted or eliminated when cartilage degenerates due to diseases. This article examines further the characteristic of this surface overlay using a combination of microscopy and imaging methods to evaluate the hypothesis that the surface of articular cartilage can be repaired by exposing degraded cartilage to aqueous synthetic lipid mixtures. The preliminary results demonstrate that it is possible to create a new surface layer of phospholipids on the surface of cartilage following artificial lipid removal, but such a layer does not possess enough mechanical strength for physiological function when created with either unsaturated palmitoyloleoyl- phosphatidylcholine or saturated dipalmitoyl-phosphatidylcholine component of joint lipid composition alone. We conclude that this may be due to low structural cohesivity, inadequate time of exposure, and the mix/content of lipid in the incubation environment.
Resumo:
Nowadays, Opinion Mining is getting more important than before especially in doing analysis and forecasting about customers’ behavior for businesses purpose. The right decision in producing new products or services based on data about customers’ characteristics means profit for organization/company. This paper proposes a new architecture for Opinion Mining, which uses a multidimensional model to integrate customers’ characteristics and their comments about products (or services). The key step to achieve this objective is to transfer comments (opinions) to a fact table that includes several dimensions, such as, customers, products, time and locations. This research presents a comprehensive way to calculate customers’ orientation for all possible products’ attributes. A use case study is also presented in this paper to show the advantages of using OLAP and data cubes to analyze costumers’ opinions.
Resumo:
To evaluate the effect of soft contact lens type on the in vivo tear film surface quality (TFSQ) on daily disposable lenses and to establish whether two recently developed techniques for noninvasive measurement of TFSQ can distinguish between different contact lens types.
Resumo:
Purpose: Young novice drivers continue to be overrepresented in fatalities and injuries arising from crashes even with the introduction of countermeasures such as graduated driver licensing (GDL). Enhancing countermeasures requires a better understanding of the variables influencing risky driving. One of the most common risky behaviours performed by drivers of all ages is speeding, which is particularly risky for young novice drivers who, due to their driving inexperience, have difficulty in identifying and responding appropriately to road hazards. Psychosocial theory can improve our understanding of contributors to speeding, thereby informing countermeasure development and evaluation. This paper reports an application of Akers’ social learning theory (SLT), augmented by Gerrard and Gibbons’ prototype/willingness model (PWM), in addition to personal characteristics of age, gender, car ownership, and psychological traits/states of anxiety, depression, sensation seeking propensity and reward sensitivity, to examine the influences on self-reported speeding of young novice drivers with a Provisional (intermediate) licence in Queensland, Australia. Method: Young drivers (n = 378) recruited in 2010 for longitudinal research completed two surveys containing the Behaviour of Young Novice Drivers Scale, and reported their attitudes and behaviours as pre-Licence/Learner (Survey 1) and Provisional (Survey 2) drivers and their sociodemographic characteristics. Results: An Akers’ measurement model was created. Hierarchical multiple regressions revealed that (1) personal characteristics (PC) explained 20.3%; (2) the combination of PC and SLT explained 41.1%; and (3) the combination of PC, SLT and PWM explained 53.7% of variance in self-reported speeding. Whilst there appeared to be considerable shared variance, the significant predictors in the final model included gender, car ownership, reward sensitivity, depression, personal attitudes, and Learner speeding. Conclusions: These results highlight the capacity for psychosocial theory to improve our understanding of speeding by young novice drivers, revealing relationships between previous behaviour, attitudes, psychosocial characteristics and speeding. The findings suggest multi-faceted countermeasures should target the risky behaviour of Learners, and Learner supervisors should be encouraged to monitor their Learners’ driving speed. Novice drivers should be discouraged from developing risky attitudes towards speeding.
Resumo:
In order to make good decisions about the design of information systems, an essential skill is to understand process models of the business domain the system is intended to support. Yet, little knowledge to date has been established about the factors that affect how model users comprehend the content of process models. In this study, we use theories of semiotics and cognitive load to theorize how model and personal factors influence how model viewers comprehend the syntactical information of process models. We then report on a four-part series of experiments, in which we examined these factors. Our results show that additional semantical information impedes syntax comprehension, and that theoretical knowledge eases syntax comprehension. Modeling experience further contributes positively to comprehension efficiency, measured as the ratio of correct answers to the time taken to provide answers. We discuss implications for practice and research.
Resumo:
This paper discusses the research carried out towards the development of a hybrid-composite floor plate systems (HCFPS) using polyurethane (PU), glass-fibre reinforced cement (GRC) and thin perforated steel laminate. HCFPS is configured in such a way where positive inherent properties of individual component materials are combined to offset any weakness and achieve the optimum performance. Finite Element modeling of HCFPS with ABAQUS 6.9-1, comparative studies of HCFPS with the steel deck composite system and experimental investigations which will be carried out are briefly described in the paper.
Resumo:
Background Scientific research is an essential component in guiding improvements in health systems. There are no studies examining the Sri Lankan medical research output at international level. The present study evaluated the Sri Lankan research performance in medicine as reflected by the research publications output between years 2000-2009. Methods This study was based on Sri Lankan medical research publication data, retrieved from the SciVerse Scopus® from January 2000 to December 2009. The process of article selection was as follows: Affiliation - 'Sri Lanka' or 'Ceylon', Publication year - 'January 2000 to December 2009' and Subject area - 'Life and Health Sciences'. The articles identified were classified according to disease, medical speciality, institutions, major international collaborators, authors and journals. Results Sri Lanka's cumulative medical publications output between years 2000-2009 was 1,740 articles published in 160 different journals. The average annual publication growth rate was 9.1%. Majority of the articles were published in 'International' (n = 950, 54.6%) journals. Most articles were descriptive studies (n = 611, 35.1%), letters (n-345, 19.8%) and case reports (n = 311, 17.9%). The articles were authored by 148 different Sri Lankan authors from 146 different institutions. The three most prolific local institutions were Universities of; Colombo (n = 547), Kelaniya (n = 246) and Peradeniya (n = 222). Eighty four countries were found to have published collaborative papers with Sri Lankan authors during the last decade. UK was the largest collaborating partner (n = 263, 15.1%). Malaria (n = 75), Diabetes Mellitus (n = 55), Dengue (n = 53), Accidental injuries (n = 42) and Lymphatic filariasis (n = 40) were the major diseases studied. The 1,740 publications were cited 9,708 times, with an average citation of 5.6 per paper. The most cited paper had 203 citations, while there were 597 publications with no citations. The Sri Lankan authors' contribution to the global medical research output during the last decade was only 0.086%. Conclusion The Sri Lankan medical research output during the last decade is only a small fraction of the global research output. There it is a necessity to setup an enabling environment for research, with a proper vision, support, funds and training. In addition, collaborations across the region need to be strengthened to face common regional health challenges. Keywords: Sri Lanka, Medical research, Publication, Analysis
Resumo:
Background The risk factors and co-factors for sporadic childhood BL are unknown. We investigated demographic and age-specific characteristics of childhood BL (0–14 years) in the U.S. Procedure BL age-standardized incidence rates (2000 U.S. standard population), were calculated using data obtained from 12 registries in the NCI’s Surveillance, Epidemiology, and End Results program for cases diagnosed from 1992 through 2005. Incidence rate ratios and 95% confidence intervals (95% CI) were calculated by gender, age-group, race, ethnicity, calendar-year period, and registry. Results Of 296 cases identified, 56% were diagnosed in lymph nodes, 21% in abdominal organs, not including retroperitoneal lymph nodes, 14% were Burkitt cell leukemia, and 9% on face/head structures. The male-to-female case ratio was highest for facial/head tumors (25:1) and lowest for Burkitt cell leukemia (1.6:1). BL incidence rate was 2.5 (95% CI 2.3–2.8) cases per million person-years and was higher among boys than girls (3.9 vs. 1.1, p<0.001) and higher among Whites and Asians/Pacific Islanders than among Blacks (2.8 and 2.9 vs.1.2, respectively, p<0.001). By ethnicity, BL incidence was higher among non-Hispanic Whites than Hispanic Whites (3.2 vs. 2.0, p=0.002). Age-specific incidence rate for BL peaked by age 3–5 years (3.4 cases per million), then stabilized or declined with increasing age, but it did not vary with calendar-year or registry area. Conclusions Our results indicate that early childhood exposures, male-sex, and White race may be risk factors for sporadic childhood BL in the United States. Keywords: epidemiology, pediatric cancer, non-Hodgkin lymphoma, HIV/AIDS
Resumo:
In persons with HIV/AIDS (PWHAs), Hodgkin lymphoma (HL) risk is increased. However, HL incidence in PWHAs has unexpectedly increased since highly active antiretroviral therapy (HAART) was introduced. We linked nationwide HIV/AIDS and cancer registry data from 1980 through 2002. Immunity was assessed by CD4 T-lymphocyte counts at AIDS onset. Annual HL incidence rates were calculated for 4 through 27 months after AIDS onset. During 477 368 person years (py's) of follow-up in 317 428 persons with AIDS (PWAs), 173 HL cases occurred (36.2 per 105 py's). Incidence was significantly higher in 1996 to 2002 than earlier. Incidence in PWAs with 150 to 199 CD4 cells/μL was 53.7 per 105 py's, whereas in PWAs with fewer than 50 CD4 cells/μL, it was 20.7 per 105 py's (Ptrend = .002). For each HL subtype, incidence decreased with declining CD4 counts, but nodular sclerosing decreased more precipitously than mixed cellularity, thereby increasing the proportion of mixed cellularity HL seen in PWAs. We conclude that HL incidence is lower with severe immunosuppression than with moderate immunosuppression, and HAART-related improvements in CD4 counts likely explain the increasing HL incidence in PWHAS observed since 1996. With more severe immunosuppression, nodular sclerosing HL becomes infrequent, explaining the higher proportion of mixed cellularity HL found in PWAs. Pathogenesis implications are discussed.
Resumo:
Natural convection in a triangular enclosure subject to non-uniformly cooling at the inclined surfaces and uniformly heating at the base is investigated numerically. The numerical simulations of the unsteady flows over a range of Rayleigh numbers and aspect ratios are carried out using Finite Volume Method. Since the upper surface is cooled and the bottom surface is heated, the air flow in the enclosure is potentially unstable to Rayleigh Benard instability. It is revealed that the transient flow development in the enclosure can be classified into three distinct stages; an early stage, a transitional stage and a steady stage. It is also found that the flow inside the enclosure strongly depends on the governing parameters; Rayleigh number and aspect ratio. The asymmetric behaviour of the flow about the geometric centre line is discussed in detailed. The heat transfer through the roof and the ceiling as a form of Nusselt number is also reported in this study.
Resumo:
Unsteady natural convection inside a triangular cavity has been studied in this study. The cavity is filled with a saturated porous medium with non-isothermal left inclined wall while the bottom surface is isothermally heated and the right inclined surface is isothermally cooled. An internal heat generation is also considered which is dependent on the fluid temperature. The governing equations are solved numerically by finite volume method. The Prandtl number, Pr of the fluid is considered as 0.7 (air) while the aspect ratio and the Rayleigh number, Ra are considered as 0.5 and 105 respectively. The effect of heat generation on the fluid flow and heat transfer have been presented as a form of streamlines and isotherms. The rate of heat transfer through three surfaces of the enclosure is also presented.
Resumo:
Brisbane writers and writing are increasingly represented as important to the city’s identity as a site of urban cool, at least in marketing and public relations paradigms. It is therefore remarkable that recent Brisbane fiction clings strongly to a particular relationship to the climatic and built environment that is often located in the past and which seemingly turns away, or at least elides, the ‘new’ technologically-driven Brisbane. Literary Brisbane is often depicted in the context of nostalgia for the Brisbane that once was—a tropical, timbered, luxuriant city in which sex is associated with heat, and, in particular, sweat. In this writing sweat can produced by adrenaline or heat, but in particular, in Brisbane novels, it is the sweat of sex that characterises the literary city. Given that Brisbane is in fact a subtropical city, it is interesting that metaphors of a tropical climate and vegetation occur so frequently in Brisbane stories (and narratives set in other parts of the state) that writer Thea Astley was prompted at one point to remark that Queensland writing was in danger of developing into a tropical cliché.
Resumo:
Two Australian researchers specializing in China's creative industries examine recent developments in southern China commonly associated with the shanzhai phenomenon (e.g., production and sale of cheap local facsimiles of globally branded goods). While shanzhai is often condemned as the embodiment of China's "knock-off" industries, the authors argue that it might be more appropriately viewed as an instance of China's emerging creative economy and an example of rapid prototyping. The paper traces the evolution of shanzhai mobile phones and the materialization of the shanzhai ethos in popular culture. In arguing that shanzhai provides inputs into creative industries, the paper describes the fuzzy boundary between formal and informal culture and notes the interaction between three spheres of activity: official culture, the market, and grassroots culture.
Resumo:
This article sketches some of the ways in which the language and concepts of cultural diversity are being taken up internationally. The debate has been driven in part by concerns about the treatment of cultural goods, services and knowledge in trade agreements. But it also involves larger questions about the role of the state, the role of non-state actors in domestic policy formation, and the shape and function of international policy communities comprising both state and non-state actors. The extent of the discussion of cultural diversity internationally is described through new formal and informal cultural networks and work towards an international instrument for cultural diversity to lay our ground rules for international trade, cultural exchange and policy principles to guide governmental responsibilities. The article concludes with analysis of some of these new networks, and investigates why Canada has been so prominent in these international efforts.