Effectiveness of powered hospital bed movers for reducing physiological strain and back muscle activation

Battery powered bed movers are becoming increasingly common within the hospital setting. The use of powered bed movers is believed to result in reduced physical efforts required by health care workers, which may be associated with a decreased risk of occupation related injuries. However, little work has been conducted assessing how powered bed movers impact on levels of physiological strain and muscle activation for the user. The muscular efforts associated with moving hospital beds using three different methods; manual pushing, StaminaLift Bed Mover (SBM) and Gzunda Bed Mover (GBM)were measured on six male subjects. Fourteen muscles were assessed moving a weighted hospital bed along a standardized route in an Australian hospital environment. Trunk inclination and upper spine acceleration were also quantified. Powered bed movers exhibited significantly lower muscle activation levels than manual pushing for the majority of muscles. When using the SBM, users adopted a more upright posture which was maintained while performing different tasks (e.g. turning a corner, entering a lift), while trunk inclination varied considerably for manual pushing and the GBM. The reduction in lower back muscular activation levels and the load reducing effect of a more upright posture may result in lower incidence of lower back injury.

Bariatric patients and the use of mobile hoists : user experiences from three hospitals in South Australia

Nursing personnel are consistently identified as one of the occupational groups most at risk of work-related musculoskeletal disorders. During the moving and handling of bariatric patients, the weight of the patient combined with atypical body mass contributes to a significant risk of injury to the care provider and patient. This is further compounded by the shape, mobility and co-operation of the patient. The aim of this study was determine user experiences and design requirements for mobile hoists with bariatric patients. Structured interviews were conducted with six experienced injury management staff from the Manual Task Services department of three hospitals in Adelaide, South Australia. All staff had experience in patient handling, the use of patient handling equipment and the provision of patient handling training. A series of open-ended questions were structured around five main themes: 1) patient factors; 2) building/vehicle space and design; 3) equipment and furniture; 4) communication; and 5) staff issues. Questions focussed on the use of mobile hoists for lifting and transferring bariatric patients. Interviews were supplemented with a walk-through of the hospital to view the types of mobile hoists used, and the location and storage of equipment. Across the three hospitals there were differing classification systems to define bariatric patients. Ensuring patient dignity, respect and privacy were viewed as important in the management and rehabilitation of bariatric patients. Storage and space constraints were considered factors restricting the use of mobile floor hoists, with ceiling hoists being the preferred method for patient transfers. When using mobile floor hoists, the forces required to push, pull and manoeuvre, as well as sudden unstable movements of the hoist were considered important risks factors giving rise to a risk of injury to the care provider. Record keeping and purchasing policies appeared to inhibit the effective use of patient handling equipment. The moving and handling of bariatric patients presents complex and challenging issues. A co-ordinated and collaborative approach for moving and handling bariatric patients is needed across the range of care providers. Designers must consider both user and patient requirements.

Evaluation of an Australian solar community : implications for education and training

1.1 Background What is renewable energy education and training? A cursory exploration of the International Solar Energy Society website (www.ises.org) reveals numerous references to education and training, referring collectively to concepts of the transfer and exchange of information and good practices, awareness raising and skills development. The purposes of such education and training relate to changing policy, stimulating industry, improving quality control and promoting the wider use of renewable energy sources. The primary objective appears to be to accelerate a transition to a better world for everyone (ISEE), as the greater use of renewable energy is seen as key to climate recovery; world poverty alleviation; advances in energy security, access and equality; improved human and environmental health; and a stabilized society. The Solar Cities project – Habitats of Tomorrow – aims at promoting the greater use of renewable energy within the context of long term planning for sustainable urban development. The focus is on cities or communities as complete systems; each one a unique laboratory allowing for the study of urban sustainability within the context of a low carbon lifestyle. The purpose of this paper is to report on an evaluation of a Solar Community in Australia, focusing specifically on the implications (i) for our understandings and practices in renewable energy education and training and (ii) for sustainability outcomes. 1.2 Methodology The physical context is a residential Ecovillage (a Solar Community) in sub-tropical Queensland, Australia (latitude 28o south). An extensive Architectural and Landscape Code (A&LC) ‘premised on the interconnectedness of all things’ and embracing ‘both local and global concerns’ governs the design and construction of housing in the estate: all houses are constructed off-ground (i.e. on stumps or stilts) and incorporate a hybrid approach to the building envelope (mixed use of thermal mass and light-weight materials). Passive solar design, gas boosted solar water heaters and a minimum 1kWp photovoltaic system (grid connected) are all mandatory, whilst high energy use appliances such as air conditioners and clothes driers are not permitted. Eight families participated in an extended case study that encompassed both quantitative and qualitative approaches to better understand sustainable housing (perceived as a single complex technology) through its phases of design, construction and occupation. 1.3 Results The results revealed that the level of sustainability (i.e. the performance outcomes in terms of a low-carbon lifestyle) was impacted on by numerous ‘players’ in the supply chain, such as architects, engineers and subcontractors, the housing market, the developer, product manufacturers / suppliers / installers and regulators. Three key factors were complicit in the level of success: (i) systems thinking; (ii) informed decision making; and (iii) environmental ethics and business practices. 1.4 Discussion The experiences of these families bring into question our understandings and practices with regard to education and training. Whilst increasing and transferring knowledge and skills is essential, the results appear to indicate that there is a strong need for expanding our education efforts to incorporate foundational skills in complex systems and decision making processes, combined with an understanding of how our individual and collective values and beliefs impact on these systems and processes.

Member moment capacities of mono-symmetric LiteSteel beam floor joists with web openings

Recently developed cold-formed LiteSteel beam (LSB) sections have found increasing popularity in residential, industrial and commercial buildings due to their light weight and cost-effectiveness. Another beneficial characteristic is that they allow torsionally rigid rectangular flanges to be combined with economical fabrication processes. Currently, there is significant interest in the use of LSB sections as flexural members in floor joist systems. When used as floor joists, these sections require openings in the web to provide access for inspection and other services. At present, however, there is no design method available that provides accurate predictions of the moment capacities of LSBs with web openings. This paper presents the results of an investigation of the buckling and ultimate strength behaviour of LSB flexural members with web openings. A detailed fine element analysis (FEA)-based parametric study was conducted with the aim of developing appropriate design rules and making recommendations for the safe design of LSB floor joists. The results include the required moment capacity curves for LSB sections with a range of web opening combinations and spans and the development of appropriate design rules for the prediction of the ultimate moment capacities of LSBs with web openings.

Design of LiteSteel Beam floor joists with web opening using an equivalent web thickness method

The LiteSteel Beam (LSB) is an innovative cold-formed steel hollow flange section. When used as floor joists, the LSB sections require holes in the web to provide access for various services. In this study a detailed investigation was undertaken into the elastic lateral distortional buckling behaviour of LSBs with circular web openings subjected to a uniform moment using finite element analysis. Validated ideal finite element models were used first to study the effect of web holes on their elastic lateral distortional buckling behaviour. An equivalent web thickness method was then proposed using four different equations for the elastic buckling analyses of LSBs with web holes. It was found that two of them could be successfully used with approximate numerical models based on solid web elements with an equivalent reduced thickness to predict the elastic lateral distortional buckling moments.

Development of an Innovative Hybrid-Composite Floor System

This paper discusses the research carried out towards the development of a hybrid-composite floor plate systems (HCFPS) using polyurethane (PU), glass-fibre reinforced cement (GRC) and thin perforated steel laminate. HCFPS is configured in such a way where positive inherent properties of individual component materials are combined to offset any weakness and achieve the optimum performance. Finite Element modeling of HCFPS with ABAQUS 6.9-1, comparative studies of HCFPS with the steel deck composite system and experimental investigations which will be carried out are briefly described in the paper.

Effects of whole-body cryotherapy (-110 degrees C) on proprioception and indices of muscle damage

The purpose of this study was to investigate the effects of whole-body cryotherapy (WBC) on proprioceptive function, muscle force recovery following eccentric muscle contractions and tympanic temperature (TTY). Thirty-six subjects were randomly assigned to a group receiving two 3-min treatments of −110 ± 3 °C or 15 ± 3 °C. Knee joint position sense (JPS), maximal voluntary isometric contraction (MVIC) of the knee extensors, force proprioception and TTY were recorded before, immediately after the exposure and again 15 min later. A convenience sample of 18 subjects also underwent an eccentric exercise protocol on their contralateral left leg 24 h before exposure. MVIC (left knee), peak power output (PPO) during a repeated sprint on a cycle ergometer and muscles soreness were measured pre-, 24, 48 and 72 h post-treatment. WBC reduced TTY, by 0.3 °C, when compared with the control group (P<0.001). However, JPS, MVIC or force proprioception was not affected. Similarly, WBC did not effect MVIC, PPO or muscle soreness following eccentric exercise. WBC, administered 24 h after eccentric exercise, is ineffective in alleviating muscle soreness or enhancing muscle force recovery. The results of this study also indicate no increased risk of proprioceptive-related injury following WBC.

Is –110°C cold air cryotherapy effective in improving post-exercise recovery in sports people?

Whole body cryotherapy (WBC) involves repeatedly exposing an individual, dressed in minimal clothing, to extremely cold air (–100 to –130°C) for a short period. One specific claim that is often made is that WBC is effective in treating exercise-induced muscle soreness and damage. However, our results suggest that two bouts of WBC were ineffective in improving recovery from eccentric exercise when administered 24 hours after eccentric exercise.

Prevention of pelvic sepsis in major open pelviperineal injury

Compound pelvic fractures are deemed to be one of the most severe orthopaedic injuries with an extremely high morbidity and mortality. After the initial resuscitation phase the prevention of pelvic sepsis is one of the main treatment goals for patients with an open pelvic fracture. If there is a suspicion of a rectal injury or if the wounds are in the perineal area, The Princess Alexandra Hospital's management plan includes early faecal diversion combined with vigorous soft tissue debridement, VAC(®) therapy and (if indicated) external fixation of the pelvic fracture. We present our flowchart for the treatment of trauma patients with compound pelvic fractures illustrated by a case report describing a 32 year old patient who sustained an open pelvic ring injury in a workplace accident. The aim of this paper is to underline the importance of a safe, straightforward approach to compound pelvic fractures.

Training the public to collect oral histories of our community : the OHAA Queensland Chapter’s model

In a digital age, the skills required to undertake an oral history project have changed dramatically. For community groups, this shift can be new and exciting, but can also invoke feelings of anxiety when there is a gap in the skill set. Addressing this gap is one of Oral History Association of Australia, Queensland (OHAA Qld) main activities. This paper reports on the OHAA Qld chapter’s oral history workshop program, which was radically altered in 2011.

Assisting ICU training management with virtual worlds

Conventional training methods for nurses involve many physical factors that place limits on potential class sizes. Alternate training methods with lower physical requirements may support larger class sizes, but given the tactile quality of nurse training, are most appropriately applied to supplement the conventional methods. However, where the importance of physical factors are periphery, such alternate training methods can provide an important way to increase upper class-size limits and therefore the rate of trained nurses entering the important role of critical care. A major issue in ICU training is that the trainee can be released into a real-life intensive care scenario with sub optimal preparation and therefore a level of anxiety for the student concerned, and some risk for the management level nurses, as patient safety is paramount. This lack of preparation places a strain on the allocation of human and non-human resources to teaching, as students require greater levels of supervision. Such issues are a concern to ICU management, as they relate to nursing skill development and patient health outcomes, as nursing training is potentially dangerous for patients who are placed in the care of inexperienced staff. As a solution to this problem, we present a prototype ICU handover training environment that has been developed in a socially interactive virtual world. Nurses in training can connect remotely via the Internet to this environment and engage in collaborative ICU handover training classes.

Theoretical perspectives on motorcycle training: reducing risk taking

Little past empirical support has been found for the efficacy of motorcycle rider training as a road safety countermeasure. However, it has been argued that rider training should focus more particularly on the psychosocial factors that influence risk taking behaviour in addition to the traditional practice of developing vehicle-handling skills. This paper examines how rider training to reduce risk taking could be guided by appropriate theories. Two fundamental perspectives are examined: firstly training can be considered in terms of behaviour change, and secondly in terms of adult learning. Whilst behaviour change theories assume some pre-existing level of dysfunctional behaviour, an adult learning perspective does not necessarily carry this assumption. This distinction in perspectives conceptually aligns with the notions of intervention and prevention (respectively), with possible implications for specific target groups for pre-licence and post-licence training. The application of the Theory of Reasoned Action (Ajzen & Fishbein, 1975, 1980) and Transformative Learning Theory (Mezirow, 1997) to a pre-licence rider training program in Queensland, Australia is discussed.

Measuring the effect of motorcycle rider training on psychosocial influences for risk taking

Aim: Whilst motorcycle rider training is commonly incorporated into licensing programs in many developed nations, little empirical support has been found in previous research to prescribe it as an effective road safety countermeasure. It has been posited that the lack of effect of motorcycle rider training on crash reduction may, in part, be due to the predominant focus on skills-based training with little attention devoted to addressing attitudes and motives that influence subsequent risky riding. However, little past research has actually endeavoured to measure attitudinal and motivational factors as a function of rider training. Accordingly, this study was undertaken to assess the effect of a commercial motorcycle rider training program on psychosocial factors that have been shown to influence risk taking by motorcyclists. Method: Four hundred and thirty-eight motorcycle riders attending a competency-based licence training course in Brisbane, Australia, voluntarily participated in the study. A self-report questionnaire adapted from the Rider Risk Assessment Measure (RRAM) was administered to participants at the commencement of training, then again at the conclusion of training. Participants were informed of the independent nature of the research and that their responses would in no way effect their chance of obtaining a licence. To minimise potential demand characteristics, participants were instructed to seal completed questionnaires in envelopes and place them in a sealed box accessible only by the research team (i.e. not able to be viewed by instructors). Results: Significant reductions in the propensity for thrill seeking and intentions to engage in risky riding in the next 12 months were found at the end of training. In addition, a significant increase in attitudes to safety was found. Conclusions: These findings indicate that rider training may have a positive short-term influence on riders’ propensity for risk taking. However, such findings must be interpreted with caution in regard to the subsequent safety of riders as these factors may be subject to further influence once riders are licensed and actively engage with peers during on-road riding. This highlights a challenge for road safety education / training programs in regard to the adoption of safety practices and the need for behavioural follow-up over time to ascertain long-term effects. This study was the initial phase of an ongoing program of research into rider training and risk taking framed around Theory of Planned Behaviour concepts. A subsequent 12 month follow-up of the study participants has been undertaken with data analysis pending.